Multi-objective optimization of process parametersduring low-pressure die casting of AZ91Dmagnesium alloy wheel castings

Multi-objective optimization has been increasingly applied in engineering where optimal decisions need to be made in the presence of trade-offs between two or more objectives. Minimizing the volume of shrinkage porosity, while reducing the secondary dendritic arm spacing of a wheel casting during low-pressure die casting(LPDC) process, was taken as an example of such problem. A commercial simulation software Pro CASTTM was applied to simulate the filling and solidification processes. Additionally, a program for integrating the optimization algorithm with numerical simulation was developed based on SiPESC. By setting pouring temperature and filling pressure as design variables, shrinkage porosity and secondary dendritic arm spacing as objective variables, the multi-objective optimization of minimum volume of shrinkage porosity and secondary dendritic arm spacing was achieved. The optimal combination of AZ91 D wheel casting was: pouring temperature 689 °C and filling pressure 6.5 kPa. The predicted values decreased from 4.1% to 2.1% for shrinkage porosity, and 88.5 μm to 81.2 μm for the secondary dendritic arm spacing. The optimal results proved the feasibility of the developed program in multi-objective optimization.

A Penalty Function Algorithm with Objective Parameters and Constraint Penalty Parameter for Multi-Objective Programming

In this paper, we present an algorithm to solve the inequality constrained multi-objective programming (MP) by using a penalty function with objective parameters and constraint penalty parameter. First, the penalty function with objective parameters and constraint penalty parameter for MP and the corresponding unconstraint penalty optimization problem (UPOP) is defined. Under some conditions, a Pareto efficient solution (or a weakly-efficient solution) to UPOP is proved to be a Pareto efficient solution (or a weakly-efficient solution) to MP. The penalty function is proved to be exact under a stable condition. Then, we design an algorithm to solve MP and prove its convergence. Finally, numerical examples show that the algorithm may help decision makers to find a satisfactory solution to MP.

A Modified Interactive Stability Algorithm for Solving Multi-Objective NLP Problems with Fuzzy Parameters in Its Objective Functions

This paper presents a modified method to solve multi-objective nonlinear programming problems with fuzzy parameters in its objective functions and these fuzzy parameters are characterized by fuzzy numbers. The modified method is based on normalized trade-off weights. The obtained stability set corresponding to α-Pareto optimal solution, using our method, is investigated. Moreover, an algorithm for obtaining any subset of the parametric space which has the same corresponding α-Pareto optimal solution is presented. Finally, a numerical example to illustrate our method is also given.

Circular object recognition based on shape parameters

To recognize circular objects rapidly in satellite remote sensing imagery, an approach using their geometry properties is presented. The original image is segmented to be a binary one by one dimension maximum entropy threshold algorithm and the binary image is labeled with an algorithm based on recursion technique. Then, shape parameters of all labeled regions are calculated and those regions with shape parameters satisfying certain conditions are recognized as circular objects. The algorithm is described in detail, and comparison experiments with the randomized Hough transformation （RHT） are also provided. The experimental results on synthetic images and real images show that the proposed method has the merits of fast recognition rate, high recognition efficiency and the ability of anti-noise and anti-jamming. In addition, the method performs well when some circular objects are little deformed and partly misshapen.

An Objective Identification Method for Wintertime Cold Fronts in Eurasia

The present study identifies wintertime cold fronts in Eurasia from gridded datasets using a new objective two-step identification scheme.The simple and classic conception of a front is adopted,where a cold front is identified as the warm boundary of the frontal zone with a suitable horizontal temperature gradient and cold advection.We combine the traditional thermal front parameter with temperature advection to first identify the cold frontal zone,and then its eastern and southern boundaries are objectively plotted as a cold front in Eurasia.By comparing different cold front identification methods,the results from this two-step cold front identification method and subjective analysis are more consistent,and the positions of the cold front identified with our method are more reasonable.This objective technique is also applied to a nationwide cold wave event over China.Results show that the horizontal extent and movement of the cold front are in good agreement with the related circulation and the associated cold weather.The proposed method and results in this study may shed light on the rapid identification of cold fronts in operational weather analysis and facilitate further research on the long-term activity characteristics of continental cold fronts.

Intelligent Antenna Attitude Parameters Measurement Based on Deep Learning SSD Model

Due to the consideration of safety,non-contact measurement methods are be-coming more acceptable.However,massive measurement will bring high labor-cost and low working efficiency.To address these limitations,this paper introduces a deep learning model for the antenna attitude parameter measurement,which can be divided into an an-tenna location phase and a calculation phase of the attitude parameter.In the first phase,a single shot multibox detector(SSD)is applied to automatically recognize and discover the antenna from pictures taken by drones.In the second phase,the located antennas’fea-ture lines are extracted and their attitude parameters are then calculated mathematically.Experiments show that the proposed algorithms outperform existing related works in effi-ciency and accuracy,and therefore can be effectively used in engineering applications.

Optimization of Cutting Parameters in Helical Milling of Carbon Fiber Reinforced Polymer

To investigate cutting performance in the helical milling of carbon fiber reinforced polymer(CFRP),experiments were conducted with unidirectional laminates.The results show that the influence of cutting parameters is very significant in the helical milling process. The axial force increases with the increase of cutting speed, which is below 95 m/min; otherwise, the axial force decreases with the increase of cutting speed. The resultant force always increases when cutting speed increases; with the increase of tangential and axial feed rates, cutting forces increase gradually. In addition, damage rings can appear in certain regions of the entry edges; therefore, the relationship between machining performance(cutting forces and holemaking quality) and cutting parameters is established using the nonlinear fitting methodology. Thus, three cutting parameters in the helical milling of CFRP, under the steady state, are optimized based on the multi-objective genetic algorithm, including material removal rate and machining performance. Finally, experiments were carried out to prove the validity of optimized cutting parameters.

Optimization of Cutting Parameters for Trade-off Among Carbon Emissions, Surface Roughness, and Processing Time

As the manufacturing industry is facing increasingly serious environmental problems, because of which carbon tax policies are being implemented, choosing the optimum cutting parameters during the machining process is crucial for automobile panel dies in order to achieve synergistic minimization of the environment impact, product quality, and processing efficiency. This paper presents a processing task-based evaluation method to optimize the cutting parameters, considering the trade-off among carbon emissions, surface roughness, and processing time. Three objective models and their relationships with the cutting parameters were obtained through input–output, response surface, and theoretical analyses, respectively. Examples of cylindrical turning were applied to achieve a central composite design(CCD), and relative validation experiments were applied to evaluate the proposed method. The experiments were conducted on the CAK50135 di lathe cutting of AISI 1045 steel, and NSGA-Ⅱ was used to obtain the Pareto fronts of the three objectives. Based on the TOPSIS method, the Pareto solution set was ranked to find the optimal solution to evaluate and select the optimal cutting parameters. An S/N ratio analysis and contour plots were applied to analyze the influence of each decision variable on the optimization objective. Finally, the changing rules of a single factor for each objective were analyzed. The results demonstrate that the proposed method is effective in finding the trade-off among the three objectives and obtaining reasonable application ranges of the cutting parameters from Pareto fronts.

Optimization of CNC Turning Machining Parameters Based on Bp-DWMOPSO Algorithm

Cutting parameters have a significant impact on the machining effect.In order to reduce the machining time and improve the machining quality,this paper proposes an optimization algorithm based on Bp neural networkImproved Multi-Objective Particle Swarm(Bp-DWMOPSO).Firstly,this paper analyzes the existing problems in the traditional multi-objective particle swarm algorithm.Secondly,the Bp neural network model and the dynamic weight multi-objective particle swarm algorithm model are established.Finally,the Bp-DWMOPSO algorithm is designed based on the established models.In order to verify the effectiveness of the algorithm,this paper obtains the required data through equal probability orthogonal experiments on a typical Computer Numerical Control(CNC)turning machining case and uses the Bp-DWMOPSO algorithm for optimization.The experimental results show that the Cutting speed is 69.4 mm/min,the Feed speed is 0.05 mm/r,and the Depth of cut is 0.5 mm.The results show that the Bp-DWMOPSO algorithm can find the cutting parameters with a higher material removal rate and lower spindle load while ensuring the machining quality.This method provides a new idea for the optimization of turning machining parameters.

Estimating Soil Hydraulic Parameters Characterizing Rainwater Infiltration and Runoff Properties of Dryland Floodplains

The two-layered (0 - 50 and 50 - 250 mm) surface horizon hydraulic parameters of three dryland floodplain soil-types under aquafer water management in Postmasburg, Northern Cape Province of South Africa were estimated with HYDRUS-1D model. Time dependent water infiltration measurements at 30 and 230 mm depths from simulated rainfalls on undisturbed 1 m2 small plots with intensities of 1.61 (high), 0.52 (medium) and 0.27 (low) mm·min-1, were minimised using a two-step inversion. Firstly, separate optimisation of the van Genuchten-Mualem model parameters for the two surface-horizon layers and secondly, simultaneous optimisation for the joint two-layered horizon with first step optimal parameters entered as initial values. The model reproduced transient water-infiltration data very well with the Nash-Sutcliffe model efficiency coefficient (NSE) of 0.99 and overestimated runoff (NSE;0.27 to 0.98). The upper surface horizon had highly optimised and variable parameters especially θs and Ks. Optimal Ks values from higher soil surface bulk-density (≥1.69 g·cm-3) were lower by at least one order of magnitude to double ring infiltrometers and water infiltration properties were different (P < 0.05) for the high rainstorm due to raindrop impact and surface crusting. Optimal α and n parameter values corresponded well with texture of the Addo (Greysols), Augrabies (Ferralsols) and Brandvlei (Cambisols) soil types. However, θs and Ksshowed greater sensitivity to model output and exerted greater influence on dryland floodplain water-infiltration and runoff characteristics. Increasing rainfall simulation period to attain near-surface saturated conditions and inclusion of surface ponding data in the inverse problem could considerable improve model prediction of hydro-physical parameters controlling surface-subsurface water distribution in fluvial environments.

Parameters optimization for direct contact membrane distillation based on orthogonal experiment

Parameter optimization integrating operation parameters and structure parameters for the purpose of high permeate flux,high productivity and low exergy consumption of direct contact membrane distillation (DCMD) process was conducted based on Taguchi experimental design. L16(45) orthogonal experiments were carried out with feed inlet temperature,permeate stream inlet temperature,flow rate,module packing density and length-diameter ratio as optimization parameters and with permeate flux,water productivity per unit volume of module and water production per unit exergy loss separately as optimization objectives. By using range analysis method,the dominance degree of the various influencing factors for the three objectives was analyzed and the optimum condition was obtained for the three objectives separately. Furthermore,the multi-objectives optimization was performed based on a weight grade method. The combined optimum conditions are feed inlet temperature 75℃,packing density 30% ,length-diameter ratio 10,permeate stream inlet temperature 30 ℃ and flow rate 25 L/h,which is in order of their dominance degree,and the validity of the optimization scheme was confirmed.

一种基于Parameter对象实现组合查询的技巧

在数据库应用程序设计中,实现组合查询的程序被大量应用,一种能够快速实现组合查询程序设计的方法可以节约大量的编程时间,提高软件开发的效率。本论文以实例论述了一种利用Parameter对象实现组合查询的方法。这种方法在VB和其它开发工具下非常容易实现。

基于FME Object的多源数据坐标转换关键技术实现

介绍了当前空间数据坐标转换的常用方法,特别是对基于FME的空间数据坐标转换的方法进行了分类总结。针对测绘成果基准各异、格式多样的特点,介绍了采用FME object技术实现多源数据坐标转换系统的开发。针对当前空间数据转换难以保证完整性和正确性的问题,总结了利用FME object读写空间数据的关键技术。此外,文章还介绍了坐标转换过程中转换模型选择和参数计算的方法。

Differences and relations of objectives, constraints, and decision parameters in the optimization of individual heat exchangers and thermal systems

Performance improvement of heat exchangers and the corresponding thermal systems benefits energy conservation, which is a multi-parameters, multi-objectives and multi-levels optimization problem. However, the optimized results of heat exchangers with improper decision parameters or objectives do not contribute and even against thermal system performance improvement. After deducing the inherent overall relations between the decision parameters and designing requirements for a typical heat exchanger network and by applying the Lagrange multiplier method, several different optimization equation sets are derived, the solutions of which offer the optimal decision parameters corresponding to different specific optimization objectives, respectively. Comparison of the optimized results clarifies that it should take the whole system, rather than individual heat exchangers, into account to optimize the fluid heat capacity rates and the heat transfer areas to minimize the total heat transfer area, the total heat capacity rate or the total entropy generation rate, while increasing the heat transfer coefficients of individual heat exchangers with different given heat capacity rates benefits the system performance. Besides, different objectives result in different optimization results due to their different intentions, and thus the optimization objectives should be chosen reasonably based on practical applications, where the inherent overall physical constraints of decision parameters are necessary and essential to be built in advance.

Multi-objective optimization of gas metal arc welding parameters and sequences for low-carbon steel (Q345D) T-joints

Q345D high-quality low-carbon steel has been extensively employed in structures with stringent weld- ing quality requirements. A multi-objective optimization of welding stress and deformation was presented to design reasonable values of gas metal arc welding parameters and sequences of Q345D T-joints. The optimized factors included continuous variables （welding current （I）, welding voltage （U） ahd welding speed （V）） and discrete variables （welding sequence （S） and welding direc- tion （D））. The concepts of the pointer and stack in Visual Basic （VB） and the interpolation method were introduced to optimize the variables. The optimization objectives included the different combina- tions of the angular distortion and transverse welding stress along the transverse and longitudinal dis- tributions. Based on the design of experiments （DOE） and the polynomial regression （PR） model, the finite element （FE） results of the T-joint were used to establish the mathematical models. The Pareto front and the compromise solutions were obtained by using a multi-objective particle swarm optimization （MOPSO） algorithm. The optimal results were validated by the corresponding results of the FE method, and the error between the FE results and the two-objective results as well as that be-tween the FE results and the three-objective optimization results were less than 17.2% and 21.5%, respectively. The influence and setting regularity of different factors were discussed according to the compromise solutions.

基于Object ARX的木门加工代码生成系统

针对木门加工领域中客户的个性化定制需求,每加工一扇木门,即使尺寸只变动一点,也必须重新制图和规划加工路径,造成生产加工耗时过多、生产效率降低。文中基于Object ARX程序设计,通过参数驱动方式绘制CAD加工图纸,对于加工尺寸改动较小的木门,只需调整变动参数,即可快速绘制木门加工图纸。根据绘制的加工图纸,从菜单上选取加工所需的刀具类型及刀具半径等参数,该界面软件快速绘图、设计加工轨迹和生成CNC加工G代码。该方法已经应用于企业生产且效果良好。

Object-Oriented Design for FDTD Visual Scientific Computing

A scheme for general purposed FDTD visual scientific computing software is introduced in this paper using object-oriented design (OOD) method. By abstracting the parameters of FDTD grids to an individual class and separating from the iteration procedure, the visual software can be adapted to more comprehensive computing problems. Real-time gray degree graphic and wave curve of the results can be achieved using DirectX technique. The special difference equation and data structure in dispersive medium are considered, and the peculiarity of parameters in perfectly matched layer are also discussed.

过盈配合工况下收缩管吸能特性分析及结构参数优化

轨道车辆收缩管在轴向冲击载荷及过盈配合下的吸能特性是吸能结构研究中的重要课题,其吸能过程依靠收缩管与锥形衬套之间的摩擦做工及收缩管的塑性变形实现,过盈配合通过影响收缩管与衬套间的接触力提高收缩管的能量耗散。为提高收缩管的吸能特性,研究过盈配合对吸能能力的影响,采用试验与有限元模型相结合的方法,基于多目标优化算法获取包括过盈量在内的收缩管最优结构参数。进行空心轴与轴套过盈静压试验,验证接触力理论公式的正确性;利用台车冲击试验研究收缩管碰撞过程中的吸能特性,构建有限元模型进行验证;推导过盈配合条件下收缩管接触表面压力的理论模型;使用全因子和Hammersley设计方法对过盈配合工况下收缩管结构参数进行研究,包括厚度(T)、过盈量(I_(ntf))、锥角长边(α_(x))和收缩比(R_(atio))。基于此,利用移动最小二乘法(MLSM)构建峰值力(PCF)、比吸能(SEA)和平均力(MCF)的近似模型。主效应分析表明,收缩比对PCF、SEA和MCF的影响最为显著。以获取最小PCF、最大SEA以及MCF最接近设计要求650 kN为优化目标,进行全局响应面(GRSM)优化,获得最优结构配置,与初始设计相比,SEA提高28.54%,PCF降低12.37%。代理模型最优解得出的MCF与有限元模型误差为2.01%,证明构建的代理模型具有较高的精度,可用于优化计算。优化后的结构有效提高了收缩管的吸能能力,降低了碰撞的初始峰值力。

改进YOLOv5s对病理学图像中猪只小肠绒毛的检测

为解决传统小肠绒毛需要专业人员手动检测耗时耗力且存在主观性和不稳定性等问题,同时提高在复杂病理学图像中小肠绒毛检测的准确率和效率,该研究提出基于改进YOLOv5s检测复杂病理学图像下猪只小肠绒毛的方法。首先,采用串联形式的混合池化对空间金字塔进行优化,增强特征提取与特征表达,提升检测精度;然后引入一种基于注意力机制的网络模块(simpleattentionmechanism,SimAM)与Bottleneck中的残差连接相结合,使用SimAM对Bottleneck中的特征图进行加权,得到加权后的特征表示,利用注意力机制加强模型对目标的感知。试验结果表明,该研究算法的平均精度(average precision)和每秒传输帧数(frame per second,FPS)达到92.43%和40帧/s。改进后的YOLOv5s在召回率和平均精度上相较改进前提高2.49和4.62个百分点,在不增加模型参数量的情况下,每帧图片的推理时间缩短1.04 ms。与经典的目标检测算法SSD、Faster R-CNN、YOLOv6s、YOLOX相比,平均精度分别提高15.16、10.56、2.03和4.07个百分点。结果表明,该方法能够实现病理学图像中猪只小肠绒毛自动化检测,保证复杂图像检测速度的同时,提高了小肠绒毛的检测精度。

改进多目标蜂群算法优化洗出运动及仿真实验

针对经典洗出算法参数选择不当导致信号缺失,引起失真,影响洗出效果等问题,提出一种改进的多目标人工蜂群算法,利用该算法对经典洗出算法中的滤波器参数进行优化来改善洗出算法的洗出效果。针对传统蜂群算法初始化和局部优化中存在的问题,引入Circle映射和Pareto局部优化算法;建立人体感知误差模型、加速度差值模型、位移模型,将模型函数作为目标函数,用改进后的多目标人工蜂群算法对经典洗出算法进行参数优化;建立仿真模型对优化后的洗出算法进行仿真验证,应用飞行模拟器运动实验平台进行实验验证。结果表明:经优化后的洗出算法,洗出逼真度得到有效提升,降低了误差峰值,改善了相位延迟,节省了运动空间。