Influence of sampling on three-dimensional surface shape measurement

In order to accurately measure an object’s three-dimensional surface shape,the influence of sampling on it was studied.First,on the basis of deriving spectra expressions through the Fourier transform,the generation of CCD pixels was analyzed,and its expression was given.Then,based on the discrete expression of deformation fringes obtained after sampling,its Fourier spectrum expression was derived,resulting in an infinitely repeated"spectra island"in the frequency domain.Finally,on the basis of using a low-pass filter to remove high-order harmonic components and retaining only one fundamental frequency component,the inverse Fourier transform was used to reconstruct the signal strength.A method of reducing the sampling interval,i.e.,reducing the number of sampling points per fringe,was proposed to increase the ratio between the sampling frequency and the fundamental frequency of the grating.This was done to reconstruct the object’s surface shape more accurately under the condition of m>4.The basic principle was verified through simulation and experiment.In the simulation,the sampling intervals were 8 pixels,4 pixels,2 pixels,and 1 pixel,the maximum absolute error values obtained in the last three situations were 88.80%,38.38%,and 31.50%in the first situation,respectively,and the corresponding average absolute error values are 71.84%,43.27%,and 32.26%.It is demonstrated that the smaller the sampling interval,the better the recovery effect.Taking the same four sampling intervals in the experiment as in the simulation can also lead to the same conclusions.The simulated and experimental results show that reducing the sampling interval can improve the accuracy of object surface shape measurement and achieve better reconstruction results.

Measurement system that improves the accuracy of polyp size determined at colonoscopy

AIM:To assess the accuracy of polyp size using an endoscopic lesion measurement system(ELMS).METHODS:The accuracy of polyp size assessment was compared among measurements acquired by visual estimation,disposable graduated biopsy forceps(DGBF;used as a"scale-plate")and the ELMS.RESULTS:There were 192 polyps from 166 cases included in this study.The mean diameter of the post polypectomy measurement was 0.85±0.53 cm(range:0.2-3.0 cm).The mean diameter by visual estimation was 1.10±0.53 cm,which was significantly different compared to the actual size of the polyp(P<0.001).The mean diameters obtained using DGBF(0.87±0.54cm)and ELMS(0.85±0.53 cm)did not significantly differ from the actual size of the polyp.The difference between the measurements from the ELMS and DGBF was not significant.CONCLUSION:Unlike visual estimations at colonoscopy,endoscopic graduated biopsy forceps and the endoscopic lesion measurement system are accurate methods to estimate polyp size.

Theoretical description of improving measurement accuracy for incoherence Mie Doppler wind lidar

For the nonlinearity of Fabry-Perot interferometer（FPI） transmission spectrum,the measurement uncertainty of incoherent Mie Doppler wind lidar based on it increases evidently with the increase of backscattering signal Doppler shift.A method of repeating the use of the approximate linear part of FPI transmission spectra for reducing the high uncertainty of a big Doppler shift is proposed.One of the ways of realizing this method is discussed in detail,in which the characteristics of FPI transmission spectrum changing with thickness and incident angle are utilized simultaneously.Under different atmosphere conditions,it has been proved theoretically that the range of measurement uncertainty drops to one-sixth while its minimum has no serious change.This method can be used not only to guide the new system design,but also as a new working way for the fabricated system.

In-situ 3D contour measurement for laser powder bed fusion based on phase guidance

In-situ layerwise imaging measurement of laser powder bed fusion(LPBF)provides a wealth of forming and defect data which enables monitoring of components quality and powder bed homogeneity.Using high-resolution camera layerwise imaging and image processing algorithms to monitor fusion area and powder bed geometric defects has been studied by many researchers,which successfully monitored the contours of components and evaluated their accuracy.However,research for the methods of in-situ 3D contour measurement or component edge warping identification is rare.In this study,a 3D contour mea-surement method combining gray intensity and phase difference is proposed,and its accuracy is verified by designed experiments.The results show that the high-precision of the 3D contours can be achieved by the constructed energy minimization function.This method can detect the deviations of common ge-ometric features as well as warpage at LPBF component edges,and provides fundamental data for in-situ quality monitoring tools.

Biopsy forceps are useful for measuring esophageal varices in vitro

BACKGROUND To avoid acute variceal bleeding in cirrhosis,current guidelines recommend screening for high-risk esophageal varices(EVs)by determining variceal size and identifying red wale markings.However,visual measurements of EV during routine endoscopy are often inaccurate.AIM To determine whether biopsy forceps(BF)could be used as a reference to improve the accuracy of binary classification of variceal size.METHODS An in vitro self-made EV model with sizes ranging from 2 to 12 mm in diameter was constructed.An online image-based survey comprising 11 endoscopic images of simulated EV without BF and 11 endoscopic images of EV with BF was assembled and sent to 84 endoscopists.The endoscopists were blinded to the actual EV size and evaluated the 22 images in random order.RESULTS The respondents included 48 academic and four private endoscopists.The accuracy of EV size estimation was low in both the visual(13.81%)and BF-based(20.28%)groups.The use of open forceps improved the ability of the endoscopists to correctly classify the varices by size(small≤5 mm,large>5 mm)from 71.85%to 82.17%(P<0.001).CONCLUSION BF may improve the accuracy of EV size assessment,and its use in clinical practice should be investigated.

Test measurements for accuracy of absolute and relative GPS positioning

The paper, after the introduction, briefly outlines the principles of both absolute and relative GPS positioning. It deals with factors and error resources affecting the accuracy of these surveying procedures. It reviews the geodetic determination of a reference point and a base line used for the test measurements. The study describes the completed test measurements, and on the basis of results, it draws the conclusions for the accuracy of the investigated surveying methods. Finally, considering these accuracy measures, their possible application in mine surveying is also mentioned very shortly.

Effect of the nonlinearity of the CCD in Fourier transform profilometry on spectrum overlapping and measurement accuracy

In Fourier transform profilometry （FTP）, we must restrain spectrum overlapping caused by the nonlinearity of the charge coupled device （CCD） and increase the measurement accuracy of the object shape. Firstly, the causes of producing higher-order spectrum components and inducing spectrum overlapping are analysed theoretically, and a simple physical ex- planation and analytical deduction are given. Secondly, aiming to suppress spectrum overlapping and improve measurement accuracy, the influence of spatial carrier frequency of projection grating on them is analysed. A method of increasing the spatial carrier frequency of projection grating to restrain or reduce the spectrum overlapping significantly is proposed. We then analyze the mechanism of how the spectrum overlapping is reduced. Finally, the simulation results and experimental measurements verify the correction of the proposed theory and method.

The Accuracy Analysis of Measurement Tools for Traffic Accident Investigation

The objective of traffic accident reconstruction is to recreate the event, which is necessary for analyzing the collision dynamics that is used as evidence in court cases. Traffic accident reconstruction and a demonstration of the event require precise data pertaining to scene measurement. However, there are differences between the individual measuring tools and methods related to traffic accident investigation, just as there are differences between the extent of their use and measurement accuracy. The most commonly applied method is the measuring tape, followed by measurements with total stations and laser rangefinders, while photogrammetry is also becoming increasingly important. The advantages and disadvantages of individual tools and methods affect the required number of investigators, portability, measurement range, applicability depending on the amount of light and weather conditions, on the possibility of remote measurement, on data collection time, on the scope, on the option to later process, the collected data and above all on the accuracy of all gathered data. The latter is crucial for proving the guilt or innocence of traffic accident participants at court, as inaccurate data can lead to an unjust sentence. Measurement accuracy using the above mentioned tools and methods also varies depending on which ones are used, as well as on other factors.

Reliability and Validity of the New Shooting Accuracy Measurement （SAM） System Software

The aim of this study was to investigate the reliability and validity of the New Shooting Accuracy Measurement Software （SAMS）. Thirty two male collegian soccer players performed three inner side kicking to the transparent goal construction. A High speed camera was placed at the back of the construction to determine where the ball contacted. Recorded video results were assessed with the SAMS and Kinovea software. To investigate test-retest reliability, three kicking results were examined twice by SAMS. Moreover kicking accuracy results obtained with SAMS were compared with results provided by Kinovea in order to investigate validity. Test-retest reproducibility of the new software was excellent, with Concordance Correlation Coefficient for distance to target （0.99, 0.99 and 0.99 respectively） and for angular degree of the ball （0.97, 0.99 and 0.99 respectively）, low Coefficients of Variation （between 2.10 to 6.33 for distance to target and 2.40 to 2.69 for angular degree） and random error （between _.＋ 0.55 to __＋ 3.44 for distance to target and ___ 0.63 to ___ 2.75 for angular degree）. Constant error （between 0.44 to 1.28 for distance to target and -1.16 to __. -2.51 for angular degree） and proportional error （between 0.97 to 0.98 for distance to target and 1.00 to 1.01 for angular degree） were very low for validity. In conclusion, the SAMS represents a valid and reliable instrument to measure accuracy of shooting to target.

Selection of a Minimal Complexity of a Transformation Functions of Pressure Sensors with a Maintained Given Measurement Accuracy

For series manufacture of pressure sensors, stage of technological tests is performed, related to a definition of the manufacturing accuracy of the sensors. Technological test plan of pressure sensors involves testing the sensors on certain fixed temperature and pressure points available in the table. According to a test results, we determine transformation function mathematical model coefficients of sensors and accordance by the claimed accuracy class, of the manufactured sensors. The cost of pressure sensors mostly depends on the cost of this step and determined by the complexity of the used transformation function model. The analysis of a contemporary works associated with the choice of transformation functions for smart pressure sensors. A new proposed indicator of model complexity of a sensor transformation function. In details shown features of the complexity indicator use and given an example. In the article was set and resolved the task to reduce the cost of the tests for commercially available sensors, by reducing the number of temperature points, without compromising the accuracy of the sensor measurement ability.

Influence of Adjusting Control Accuracy on Pressure Probe Measurements in Turbo Machines

This paper presents a new design of a probe adjusting device intended to position pressure and temperature probes in a flow field. 5-hole, 3-hole and temperature probes can be moved in radial direction and freely rotated about their axis. The high actuation accuracy of 3.9 ktm in radial direction and 0.09~ in angular position is validated in a 2-stage-turbine test rig which is installed at the Institute of Power Plant Technology, Steam and Gas Turbines, RWTH Aachen University. To meet the challenge to calculate the efficiency of a turbo machine which is mainly influenced by the temperature, all probe adjusting devices are positioned simultaneously and controlled by the MAS （measuring acquisition system） so that the same radial position in each stage is measured at the same time. For this purpose a new program has been developed to synchronize actuation and measurement. The slim design of 60 mm width allows measurement between the stages of turbo machines with small axial distances between vane and blade. In addition a CFD/FEA shows how the design and combination of materials compensate the thermal expansion of the engine during operation. This allows a minimal safety distance of 0.2 mm between rotor and probe to enable measurement as close to the physical boundary as possible. The actuation accuracy is demonstrated with pressure, temperature and angle distribution plots. It is also shown that the resolution of the measuring points, and therefore the actuation distances, has a large impact on the flow field analysis and should be set as high as possible. However the measuring time has to be taken into account.

Multiple Measurement Models of Articulated Arm Coordinate Measuring Machines

The existing articulated arm coordinate measuring machines（AACMM） with one measurement model are easy to cause low measurement accuracy because the whole sampling space is much bigger than the result in the unstable calibration parameters. To compensate for the deficiency of one measurement model, the multiple measurement models are built by the Denavit-Hartenberg＇s notation, the homemade standard rod components are used as a calibration tool and the Levenberg-Marquardt calibration algorithm is applied to solve the structural parameters in the measurement models. During the tests of multiple measurement models, the sample areas are selected in two situations. It is found that the measurement errors＇ sigma value（0.083 4 ram） dealt with one measurement model is nearly two times larger than that of the multiple measurement models（0.043 1 ram） in the same sample area. While in the different sample area, the measurement errors＇ sigma value（0.054 0 ram） dealt with the multiple measurement models is about 40% of one measurement model（0.137 3 mm）. The preliminary results suggest that the measurement accuracy of AACMM dealt with multiple measurement models is superior to the accuracy of the existing machine with one measurement model. This paper proposes the multiple measurement models to improve the measurement accuracy of AACMM without increasing any hardware cost.

Non-destructive Measurement of Magnetic Properties of Claw Pole

The magnetic properties of the claw pole have a direct effect on the output power of a generator Many methods can be used to measure these magnetic properties,each with its own advantages,but an important shortcoming is that all are destructive.In this study,a new non-destructive method to measure the magnetic properties of claw pole was proposed and a corresponding testing set-up was designed.A finite-element model was constructed to simulate the measurement process.Results proved that the measured magnetization-like curves had good agreement with the trend of the input magnetic curves and the effect of the positioning error in the measuring process could be neglected.To further validate the new method,seven types of claw poles of different materials subjected to different heat-treatment processes were forged and tested by both the new method and the conventional ring-sample method.Compared with the latter,the new method showed better consistency,relatively higher accuracy,and much stronger stability of measurement results;however,its sensitivity needs to be improved.The effects of material compositions and heat-treatment parameters on the magnetic properties of the claw pole were briefly analyzed.

A light field measurement system through PSF estimation by a morphology-based method

Light field imaging technology can obtain three-dimensional(3D)information of a test surface in a single exposure.Traditional light field reconstruction algorithms not only take a long time to trace back to the original image,but also require the exact parameters of the light field system,such as the position and posture of a microlens array(MLA),which will cause errors in the reconstructed image if these parameters cannot be precisely obtained.This paper proposes a reconstruction algorithm for light field imaging based on the point spread function(PSF),which does not require prior knowledge of the system.The accurate PSF derivation process of a light field system is presented,and modeling and simulation were conducted to obtain the relationship between the spatial distribution characteristics and the PSF of the light field system.A morphology-based method is proposed to analyze the overlapping area of the subimages of light field images to identify the accurate spatial location of the MLA used in the system,which is thereafter used to accurately refocus light field imaging.A light field system is built to verify the algorithm’s effectiveness.Experimental results show that the measurement accuracy is increased over 41.0%compared with the traditional method by measuring a step standard.The accuracy of parameters is also improved through a microstructure measurement with a peak-to-valley value of 25.4%and root mean square value of 23.5%improvement.This further validates that the algorithm can effectively improve the refocusing efficiency and the accuracy of the light field imaging results with the superiority of refocusing light field imaging without prior knowledge of the system.The proposed method provides a new solution for fast and accurate 3D measurement based on a light field.

Error analysis of non-spherical raindrops on precipitation measurement

Radar cross section （RCS） of non-sphericai raindrops is calculated by using the software CST based on finite integral method and compared with RCS of spherical raindrops. The revised factor of non-spherical raindrops is obtained. The radar reflectivity with precipitation change of four distribution models of M-P, Gamma, JD and JT combining the revised factor is gotten using trapezoidal integration. When the infuence of non-spherical raindrops is considered, the accuracy of precipitation measurement of four distribution models can be separately improved 8.77%, 8.47%, 10.53% and 8.04% in the case of rain intensity is 100 mm/h.

Carrier fringe method of moire interferometry for tiny strain measurements in micro-field

In this paper, we demonstrate a new optical method for tiny strain measurements based on the principle of carrier fringes of moire interferometry. A cross-line grating with frequency of 1200 lp/mm is replicated on the specimen surface, and the strain can be deduced from the changes in carrier fringes before and after the deformation of an object. Four coherent laser beams are used to obtain the carrier fringe patterns of field U and V. Both theoretical analysis and numerical simulation indicate that the ideal accuracy of strain can be controlled within a range of ±1με. Case study of a plane extension experiment shows that the measurement accuracy of strain can be controlled within the range of ±10με. The average strain values of every row of field U and every column of field V can be obtained by using this method, and approximated strain of every pixel in the whole-field can be further acquired, and thus it is possible to measure tiny strains occurred in a micro-field. The technology in this paper can provide comprehensive information for analyzing related mechanical content in the field of MEMS.

A new method of phase measurement based on optimization

A new method of phase measurement based on optimization is presented. Simulations were ran with synthesized signals, and comparison was made with some spectral domain methods. The results show that, with a suitable number of samples processed, this method is superior to other methods in terms of accuracy, while the amplitude and phase of distortion component have no effect on accuracy.

Research on inter-satellite measurement technique in high dynamic environment

An improved measurement algorithm, based upon the theory of two-way time transfer （ TWTT）, is proposed to measure satellites with high speeds. The algorithm makes theoretical analyses and corresponding deductions on a relative motion model of two satellites, and eliminates the measurement error caused by the equipment delay when a satellite moves at a high speed. Theoretical analysis and simulation results demonstrate that in comparison with the conventional TWTT algorithm, the proposed algorithm can significantly enhance the measurement accuracy of the inter-satellite ranging and time synchronization, and the algorithm is more effective with the relative velocity between the satellites and transmitting delay becoming larger.

THE ESTIMATE AND MEASUREMENT OF TRANSVERSE WAVE INTENSITY

Transverse waves are a type of structural waves and should be considered in the analysis of high frequency vibration because the energy carried by transverse waves increases with the increase of frequency and becomes important at high frequencies. This paper studies the estimate theory and measuring technique of the transverse wave intensity in two-dimensional homogeneous structures. In general, the intensity vector is the sum of the effective intensity vector and the intensity variation vector. Each axial intensity component is proportional to two imaginary parts of cross spectral densities and its estimate is complicated. For the special case where transverse waves propagate in one direction, the intensity variation is zero and the estimate of the intensity is simplified. The intensity technique is formed based on the finite difference principle. Transverse wave intensity can be measured using a pair of two-transducer arrays lying in the orthogonal direction for the general case or a two-transducer array lying in the propagating direction for the special case. In order to assess the measurement accuracy of transverse wave intensify, the coupling loss factors from bending to transverse waves in building structures were measured using the intensity technique and compared with the results predicted and measured using the conventional method. It is shown that the agreement between the results measured using the intensity technique and that by the conventional method is good.