The Impact of Model Based Offset Scaling Technique on the Amplitude Variation with Offset Responses from 3D Seismic Data Acquired from the Tano Basin, Offshore Ghana

Amplitudes have been found to be a function of incident angle and offset. Hence data required to test for amplitude variation with angle or offset needs to have its amplitudes for all offsets preserved and not stacked. Amplitude Variation with Offset (AVO)/Amplitude Variation with Angle (AVA) is necessary to account for information in the offset/angle parameter (mode converted S-wave and P-wave velocities). Since amplitudes are a function of the converted S- and P-waves, it is important to investigate the dependence of amplitudes on the elastic (P- and S-waves) parameters from the seismic data. By modelling these effects for different reservoir fluids via fluid substitution, various AVO geobody classes present along the well and in the entire seismic cube can be observed. AVO analysis was performed on one test well (Well_1) and 3D pre-stack angle gathers from the Tano Basin. The analysis involves creating a synthetic model to infer the effect of offset scaling techniques on amplitude responses in the Tano basin as compared to the effect of unscaled seismic data. The spectral balance process was performed to match the amplitude spectra of all angle stacks to that of the mid (26°) stack on the test lines. The process had an effect primarily on the far (34° - 40°) stacks. The frequency content of these stacks slightly increased to match that of the near and mid stacks. In offset scaling process, the root mean square (RMS) amplitude comparison between the synthetic and seismic suggests that the amplitude of the far traces should be reduced relative to the nears by up to 16%. However, the exact scaler values depend on the time window considered. This suggests that the amplitude scaling with offset delivered from seismic processing is only approximately correct and needs to be checked with well synthetics and adjusted accordingly prior to use for AVO studies. The AVO attribute volumes generated were better at resolving anomalies on spectrally balanced and offset scaled data than data delivered from conventional processing. A typical class II AVO anomaly is seen along the test well from the cross-plot analysis and AVO attribute cube which indicates an oil filled reservoir.

基于SBAS-InSAR与Offset-Tracking的色东普流域灾前形变探究

利用SAR偏移量追踪(offset-tracking)技术获取冰川形变作为SBAS-InSAR的补充,采用2种技术计算2018-01~10色东普流域灾前形变,联合分析灾前形变特征及影响因素。结果表明,色东普流域冰川与沟道在2018-10-17冰崩灾害发生前已出现形变;冰川主要形变区形变趋势表现为加速-平缓-加速,7~9月形变量达到-7.69 m;沟道内堆积物长期呈下滑趋势,7月后与冰川均加速形变;气温升高是冰崩碎屑流灾害发生的主导因素。联合SBAS-InSAR与offset-tracking技术能够满足不同形变量级的监测需求,可用于冰崩灾害的早期识别与形变反演,为青藏高原地区冰崩灾害防治提供参考。

Permanent Magnet Temperature Estimation for PMSMs Using Virtual Position-offset Injection

This paper proposes a virtual position-offset injection based permanent magnet temperature estimation approach for permanent magnet synchronous machines(PMSMs). The concept of virtual position-offset injection is mathematically transforming the machine model to a virtual frame with a position-offset. The virtual frame temperature estimation model is derived to calculate the permanent magnet temperature(PMT) directly from the measurements with computation efficiency. The estimation model involves a combined inductance term, which can simplify the establishment of saturation compensation model with less measurements. Moreover, resistance and inverter distorted terms are cancelled in the estimation model, which can improve the robustness to the winding temperature rise and inverter distortion. The proposed approach can achieve simplified computation in temperature estimation and reduced memory usage in saturation compensation. While existing model-based approaches could be affected by either the need of resistance and inverter information or complex saturation compensation. Experiments are conducted on the test machine to verify the proposed approach under various operating conditions.

Analytical Determination of Size and Location of Roadside Horizontal Sightline Offsets for Compound Curves

AASHTO’s guideline for geometric design of highways and similar guidelines require that roadside areas on the inside of horizontal curves be cleared of high objects to provide stopping sight distance. The guidelines have analytical models for determining the extent of clearance, known as the horizontal sightline offset or clearance offset, for simple curves. Researchers in the past have developed analytical models for clearance offsets for spiraled and reverse curves. Very few researchers developed analytical models for available sight distances for compound curves. Still missing are models for horizontal sightline offsets and locations of the offsets for compound curves. The objective of this paper is to present development of analytical models and charts for determining horizontal sightline offsets and their locations for compound curves. The paper considers curves whose component arcs are individually shorter than stopping sight distance. The resulting models and the charts have been verified with accurate values determined using graphical methods. The models and the charts will find application in geometric design of highway compound curves.

Offset restoration in total hip arthroplasty:Important:A current review

Normal vertical and horizontal offset is essential for hip biomechanics,muscle functioning and gait pattern.Total hip arthroplasty(THA)should aim to restore normal offset with implantation of femoral and acetabular components.This would be possible with proper preoperative planning,templating and ensuring implant options are available for offset restoration.Templating is essential for understanding the vertical and horizontal offset change,especially in hip arthritis presenting late with significant limb length discrepancy at THA.Planning should include appropriate soft tissue releases and the use of ideal implants to achieve restoration of horizontal and vertical offset.Under correction of horizontal offset at THA for fracture neck of femur could result in abductor fatigue,limp and increased wear.Restoration of horizontal offset is imperative at THA for a fractured neck of the femur to achieve optimal abductor function.Horizontal offset is necessary for optimal abductor muscle tension and function.Revision THA for acetabular bone loss would require hip center restoration with the acetabular and femoral offset correction to achieve limb length correction and abductor length.The inability to achieve vertical and horizontal offset correction could lead to dislocation or signs of abductor fatigue.Careful vertical and horizontal femur offset restoration is required for normal hip biomechanics,decreased wear and increased longevity.

Near resonance vibration isolation on a levered-dual response(LEDAR)Coulomb-damped system by differential preloads/offsets in linear springs

The levered-dual response(LEDAR)Coulomb-damped system attains near resonant vibration isolation by differential preloads/offsets in linear springs.It takes the advantages of both the preloads/offsets in linear springs and the guiderail friction for realizing different levels of vibration isolation.The isolation capacities are investigated on the strategies with both the horizontal and vertical guiderails,with the horizontal rail only,and without guiderails.The compressive preloads generally result in the consumption of most of the initial excitation energy so as to overcome the potential threshold.The isolation onsets at the frequency ratio of 1∓0.095 on the left-hand side(LHS)and the right-hand side(RHS)of the lever are relative to the load plate connector.The observed near resonant isolation thus makes the LEDAR system a candidate for the isolation of the mechanical systems about resonance while opening a path for simultaneous harvesterisolation functions and passive functions at extreme frequencies.

The Effect of Lateral Offset Distance on the Aerodynamics and Fuel Economy of Vehicle Queues

The vehicle industry is always in search of breakthrough energy-saving and emission-reduction technologies.In recent years,vehicle intelligence has progressed considerably,and researchers are currently trying to take advantage of these developments.Here we consider the case of many vehicles forming a queue,i.e.,vehicles traveling at a predetermined speed and distance apart.While the majority of existing studies on this subject have focused on the influence of the longitudinal vehicle spacing,vehicle speed,and the number of vehicles on aerodynamic drag and fuel economy,this study considers the lateral offset distance of the vehicle queue.The group fuel consumption savings rate is calculated and analyzed.As also demonstrated by experimental results,some aerodynamic benefits exist.Moreover,the fuel consumption saving rate of the vehicle queue decreases as the lateral offset distance increases.

A Residual Frequency Offset Estimation Method Based on Range Migration Fitting

Recently,researchers have proposed an emitter localization method based on passive synthetic aperture.However,the unknown residual frequency offset(RFO)between the transmit-ter and the receiver causes the received Doppler signal to shift,which affects the localization accu-racy.To solve this issue,this paper proposes a RFO estimation method based on range migration fitting.Due to the high frequency modulation slope of the linear frequency modulation(LFM)-mod-ulation radar signal,it is not affected by RFO in range compression.Therefore,the azimuth time can be estimated by fitting the peak value position of the pulse compression in range direction.Then,the matched filters are designed under different RFOs.When the zero-Doppler time obtained by the matched filters is consistent with the estimated azimuth time,the given RFO is the real RFO between the transceivers.The simulation results show that the estimation error of azimuth distance does not exceed 20 m when the received signal duration is not less than 3 s,the pulse repe-tition frequency(PRF)of the transmitter radar signal is not less than 1 kHz,the range detection is not larger than 1000 km,and the signal noise ratio(SNR)is not less than-5 dB.

Modulation Recognition with Frequency Offset and Phase Offset over Multipath Channels

Modulation recognition becomes unreliable at low signal-to-noise ratio(SNR)over fading channel.A novel method is proposed to recognize the digital modulated signals with frequency and phase offsets over multi-path fading channels in this paper.This method can overcome the effects of phase offset,Gaussian noise and multi-path fading.To achieve this,firstly,the characteristic parameters search is constructed based on the cyclostationarity of received signals,to overcome the phase offset,Gaussian white noise,and influence caused by multi-path fading.Then,the carrier frequency of the received signal is estimated,and the maximum characteristic parameter is searched around the integer multiple carriers and their vicinities.Finally,the modulation types of the received signal with frequency and phase offsets are classified using decision thresholds.Simulation results demonstrate that the performance of the proposed method is better than the traditional methods when SNR is over 5dB,and that the proposed method is robust to frequency and phase offsets over multipath channels.

A new method for coseismic offset detection from GPS coordinate time series

Currently,the extraction of coseismic offset signals primarily relies on earthquake catalog data to determine the occurrence time of earthquakes.This is followed by the process of differencing the average GPS coordinate time series data,with a time interval of 3 to 5 days before and after the earthquake.In the face of the huge amount of GPS coordinate time series data today,the conventional approach of relying on earthquake catalog data to assist in obtaining coseismic offset signals has become increasingly burdensome.To address this problem,we propose a new method for automatically detecting coseismic offset signals in GPS coordinate time series without an extra earthquake catalog for reference.Firstly,we pre-process the GPS coordinate time series data for filtering out stations with significant observations missing and detecting and removing outliers.Secondly,we eliminate other signals and errors in the GPS coordinate time series,such as trend and seasonal signals,leaving the coseismic offset signals as the primary signal.The resulting coordinate time series is then modeled using the first-order difference and data stacking method.The modeling method enables automatic detection of the coseismic offset signals in the GPS coordinate time series.The aforementioned method is applied to automatically detect coseismic offset signals using simulated data and the Searles Valley GPS data in California,USA.The results demonstrate the efficacy of our proposed method,successfully detecting coseismic offsets from vast amounts of GPS coordinate time series data.

Reconstructing in vivo spatially offset Raman spectroscopy of human skin tissue using a GPU-accelerated Monte Carlo platform

As one type of spatially offset Raman spectroscopy(SORS), inverse SORS is particularly suited to in vivo biomedical measurements due to its ring-shaped illumination scheme. To explain inhomogeneous Raman scattering during in vivo inverse SORS measurements, the light–tissue interactions when excitation and regenerated Raman photons propagate in skin tissue were studied using Monte Carlo simulation. An eight-layered skin model was first built based on the latest transmission parameters. Then, an open-source platform, Monte Carlo e Xtreme(MCX), was adapted to study the distribution of 785 nm excitation photons inside the model with an inverse spatially shifted annular beam. The excitation photons were converted to emission photons by an inverse distribution method based on excitation flux with spatial offsets Δs of 1 mm, 2 mm, 3 mm and 5 mm. The intrinsic Raman spectra from separated skin layers were measured by continuous linear scanning to improve the simulation accuracy. The obtained results explain why the spectral detection depth gradually increases with increasing spatial offset, and address how the intrinsic Raman spectrum from deep skin layers is distorted by the reabsorption and scattering of the superficial tissue constituents. Meanwhile, it is demonstrated that the spectral contribution from subcutaneous fat will be improved when the offset increases to 5 mm, and the highest detection efficiency for dermal layer spectral detection could be achieved when Δs = 2 mm. Reasonably good matching between the calculated spectrum and the measured in vivo inverse SORS was achieved, thus demonstrating great utility of our modeling method and an approach to help understand the clinical measurements.

Assessment of the ballistic response of honeycomb sandwich structures subjected to offset and normal impact

In the present study,experimental and numerical investigations were carried out to examine the behavior of sandwich panels with honeycomb cores.The high velocity impact tests were carried out using a compressed air gun.A sharp conical nosed projectile was impacted normally and with some offset distance(20 mm and 40 mm).The deformation,failure mode and energy dissipation characteristics were obtained for both kinds of loading.Moreover,the explicit solver was run in Abaqus to create the finite element model.The numerically obtained test results were compared with the experimental to check the accuracy of the modelling.The numerical result was further employed to obtain strain energy dissipation in each element by externally running user-defined code in Abaqus.Furthermore,the influence of inscribe circle diameter and cell wall and face sheet thickness on the energy dissipation,deformation and failure mode was examined.The result found that ballistic resistance and deformation were higher against offset impact compared to the normal impact loading.Sandwich panel impacted at 40 mm offset distance required 3 m/s and 1.9 m/s more velocity than 0 and 20 mm offset distance.Also,increasing the face sheet and wall thickness had a positive impact on the ballistic resistance in terms of a higher ballistic limit and energy absorption.However,inscribe circle diameter had a negative influence on the ballistic resistance.Also,the geometrical parameters of the sandwich structure had a significant influence on the energy dissipation in the different deformation directions.The energy dissipation in plastic work was highest for circumferential direction,regardless of impact condition followed by tangential,radial and axial directions.

Massive Unsourced Random Access Under Carrier Frequency Offset

Unsourced random access(URA)is a new perspective of massive access which aims at supporting numerous machine-type users.With the appearance of carrier frequency offset(CFO),joint activity detection and channel estimation,which is vital for multiple-input and multiple-output URA,is a challenging task.To handle the phase corruption of channel measurements under CFO,a novel compressed sensing algorithm is proposed,leveraging the parametric bilinear generalized approximate message passing framework with a Markov chain support model that captures the block sparsity structure of the considered angular domain channel.An uncoupled transmission scheme is proposed to reduce system complexity,where slot-emitted messages are reorganized relying on clustering unique user channels.Simulation results reveal that the proposed transmission design for URA under CFO outperforms other potential methods.

Shaped Offset Quadrature Phase Shift Keying Based Waveform for Fifth Generation Communication

Fifth generation(5G)wireless networks must meet the needs of emerging technologies like the Internet of Things(IoT),Vehicle-to-everything(V2X),Video on Demand(VoD)services,Device to Device communication(D2D)and many other bandwidth-hungry multimedia applications that connect a huge number of devices.5G wireless networks demand better bandwidth efficiency,high data rates,low latency,and reduced spectral leakage.To meet these requirements,a suitable 5G waveform must be designed.In this work,a waveform namely Shaped Offset Quadrature Phase Shift Keying based Orthogonal Frequency Division Multiplexing(SOQPSK-OFDM)is proposed for 5G to provide bandwidth efficiency,reduced spectral leakage,and Bit Error Rate(BER).The proposed work is evaluated using a real-time Software Defined Radio(SDR)testbed-Wireless open Access Research Platform(WARP).Experimental and simulation results show that the proposed 5G waveform exhibits better BER performance and reduced Out of Band(OOB)radia-tion when compared with other waveforms like Offset Quadrature Phase Shift Key-ing(OQPSK)and Quadrature Phase Shift Keying(QPSK)based OFDM and a 5G waveform candidate Generalized Frequency Division Multiplexing(GFDM).BER analysis shows that the proposed SOQPSK-OFDM waveform attains a Signal to Noise Ratio(SNR)gain of 7.2 dB at a BER of 10�3,when compared with GFDM in a real-time indoor environment.An SNR gain of 8 and 6 dB is achieved by the proposed work for a BER of 10�4 when compared with QPSK-OFDM and OQPSK-OFDM signals,respectively.A significant reduction in OOB of nearly 15 dB is achieved by the proposed work SOQPSK-OFDM when compared to 16 Quadrature Amplitude Modulation(QAM)mapped OFDM.

孤岛微电网多虚拟同步发电机频率无差协调控制策略

传统虚拟同步发电机的频率控制为有差控制,且虚拟惯量的引入使得虚拟同步发电机呈现二阶振荡特性,导致孤岛微电网多虚拟同步发电机并联系统在受到负荷扰动时面临频率偏移和有功超调的问题。针对此,提出了一种多虚拟同步发电机频率无差协调控制方法。该方法包含了兼具有功精确分配的频率无差调节控制和阻尼改进控制两部分,通过利用母线频率全局一致的“通信”效果,以分散式的形式协调系统内各台虚拟同步发电机,可主动消除微电网频率稳态偏差且实现各台虚拟同步发电机按照容量承担负荷有功功率,并抑制系统的有功超调。最后,通过仿真和实验验证了所提控制方法的有效性。

主轴热偏移特性检测与影响分析

主轴的热偏移误差直接影响数控机床的定位精度及加工质量。针对数控机床主轴温升及热偏移误差的测试问题,利用磁吸式温度传感器、激光测试仪对主轴温度变化与各方向热偏移误差进行测量,了解机床主轴实际工况,收集主轴温升数据及热平衡时间、主轴热偏移空间状态,分析主轴温升与热偏移误差随测试组数的变化关系。实验结果表明:主轴温升与测试组数的增加呈正比例关系,高转速最大温升12.65℃,明显高于低转速温升8.55℃;主轴各方向热偏移误差随温升而变大,其中高转速下误差变化更剧烈,高、低转速下的最大热偏移分别为35.37μm和15.26μm。本研究成果为以后探寻误差成因及优化补偿设计提供了数据支撑。

周边眼偏位空孔爆破设计优化研究与应用

依据已有研究对空孔效应和设置空孔时裂纹扩展规律进行探讨,发现空孔有利于裂纹贯通,对提升爆破效果有一定帮助,但也发现传统的直线型空孔布置会导致裂纹偏向,即在空孔附近转向、偏离原发展路径,影响原设计开挖轮廓。若设置偏位空孔,则可充分利用空孔效应及导向作用以提高开挖质量。对于偏位空孔在爆破中的效应,采用数值模拟研究了不同炮孔间距、空孔偏位角下的裂纹扩展规律和炮孔间贯通情况,探讨了最优偏位角度设计,并根据模拟结果对现场爆破方案进行优化,研究实际应用效果。研究结果表明:偏位空孔对爆生裂纹具有较直线空孔更明显的导向作用,主要表现在爆生裂纹尖端向空孔本身发展或被空孔裂纹引导偏向、最终主裂纹与空孔连通或在空孔范围之外主裂纹相贯通,更利于炮孔主裂纹扩展与贯通;通过提取模拟结果并测量裂纹范围,对于孔间距在60 cm及以下时,适用于周边眼爆破设计的最优偏位角为15°,在此情况下炮孔连线方向形成了与孔心连线相平行的裂纹,能显著提升贯通效果;对于优化后的福厦铁路某隧道爆破施工方案,通过振速监测及超欠挖断面扫描分析,发现周边眼起爆引起的爆破振速降低了超过50%,超欠挖值也由平均25 cm降低至15 cm以内,整体应用效果良好。该项研究可为隧道爆破减振及超欠挖控制研究提供一定参考。

盾构注浆荷载作用下带榫管片水平轴线偏移量计算方法研究

为探明隧道盾构注浆荷载作用引起带榫管片水平轴线偏移规律,以小曲率半径盾构隧道为例,分析壁后注浆引起管片上浮的诱因,考虑管片环“椭圆化”变形、纵向连接螺栓预应力、环缝影响范围和横向刚度等综合因素的影响,建立榫杆连接条件下带榫环缝的管片单元纵向等效抗弯刚度有效率计算式,并通过计算盾构注浆荷载作用下带榫管片的静态和动态上浮力,构建盾构注浆荷载作用下带榫管片上浮力计算表达式,由此分析小曲率半径隧道盾构注浆荷载作用下带榫管片受力情况及其在文克尔弹性地基梁假定条件下受上浮力作用的挠曲变形规律,建立盾构注浆荷载作用下带榫管片水平轴线偏移量计算方法,并依托实际工程加以验证。结果表明:该文理论值与模拟值和监测值均拟合良好,该文计算方法具有良好的工程适用性,可为盾构隧道工程及其类似工程中注浆荷载作用下管片偏移及错台问题提供有效的理论指导。

空空高速移动通信信号的频偏估计和跟踪算法

空空高速移动场景下飞行平台通信信号的多普勒频率范围大且变化快。针对现有频偏估计和跟踪算法难以兼顾估计精度和工程可实现性的难题,提出了低复杂度的新型高精度频偏估计和跟踪算法。首先根据空空高速移动场景下多普勒频率快速变化且具有时空相关性特征,在传统频偏模型的基础上构建适用于空空高速移动场景的时变频偏模型;然后基于此模型将相邻短前导的频偏估计值进行相互关联并处理,将频偏精度优化问题转化为经典的超定线性方程组的优化求解问题,最大限度地抑制了估计噪声,提高了频偏估计精度。仿真结果表明,该算法估计的残余频偏相对于经典算法大幅降低,当信噪比大于5 dB时,残余频偏的均方根误差控制在100 Hz范围内。针对该算法求解过程中存在的数值稳定性问题,给出了相应的工程可实现方法。该算法采用前馈补偿频偏跟踪方法,与传统的锁相环反馈跟踪方法相比,提高了系统的稳定性和时效性。

基于过零点斜率加窗解调的ACARS信号接收方法

飞机通信寻址与报告系统(ACARS)允许飞机和地面站之间发送和接收报文,在保障飞行安全、实现空中交通管制等方面具有重要意义。通信链路的噪声和频偏是影响ACARS信号接收性能的关键因素。针对ACARS信号接收过程中的失真等问题,深入研究频偏、噪声等因素与ACARS报文接收性能之间的关系;在充分考虑噪声与多普勒频移等因素的基础上,提出基于过零点斜率加窗解调的ACARS信号接收方法,并从理论和仿真分析2方面探讨不同方法的抗频偏抗噪声能力;设计并搭建基于软件无线电平台的ACARS信号接收系统。通过对ACARS报文接收性能的仿真分析和真实报文接收性能的对比分析,表明所提方法在提升抗噪声和频偏能力、降低误码率等方面均具有优势。