Separation and Characterization of Nitrogen-Rich Components in Coker Gas Oils from Athabasca Bitumen

It is well known that gas oils from oilsands bitumen are difficult to hydrotreat. In order to develop the most appropriate flow sheet and operating conditions, a thorough knowledge of the molecular structure and behaviour of bitumen and its gas oil products is needed. In this work, the gas oil samples are fractionated in an attempt to isolate and identify the problematic molecular species for hydrotreating. It is found that the major nitrogen sources in coker gas oils are associated with relatively small pentane insoluble species and an even smaller, highly polar, hexane insoluble species. Structural information obtained for these fractions indicates that they are formed during the cracking of resin molecules. Nitrogen speciation shows that the pyrroles are the primary nitrogen type, with pyridines also being an important species. Both nitrogen species are undesirable in the hydrotreating process. Pyrroles in particular are subject to polymerisation, producing gums and sediments that foul filters and other equipment while pyridines can directly deactivate the hydrotreating catalyst.

Separation of Toluene Insoluble Matter from Syncrude Coker Heavy Gas Oil

Toluene insoluble matter (TIM) in coker heavy gas oil (CHGO) from oil sands bitumen is harmful to the downstream hydrotreating, and it may be difficult to be removed by conventional filtration. In order to determine its origin, the TIM must first be separated from CHGO for characterization. Two techniques are described to accomplish this goal. In the ultra-centrifugation approach used in this work, CHGO is blended with a miscible liquid and centrifuged under 366000 G (gravity) force. Through this procedure toluene and hexane diluents yielded TIM contents of 24μg·g-1 and 88μg·g-1 respectively. In an alternative simplified procedure, the initial ultra-centrifugation step is omitted. Several different solvents are evaluated for use as diluents but, in each case, toluene is still used in the subsequent washing steps. TIM contents determined by this method range from 23 to about 200μg·g-1. The amount of TIM separated by means of this method depends primarily on the initial diluent used. Other conditions, such as diluent-oil ratio, water-oil ratio, mixing time, temperature and water pH value, are also studied.

Cocracking and Separate Cracking of Straight-Run Gasoline and Light Gas Oil

This paper presents experimental results of cocracking of straight-run gasoline (SRG) and light gaS oil (LGO) in an improved pulsed-micro-pyrolyzer. It is shown that there are negative opergistic effect on the yields and selectivities of ethylene and propylene in cocracking. The difference in coking tendencies betWeen the cocracking and the separate cracking is compared as well.

Extraction of essential oil from shaddock peel and analysis of its components by gas chromatography-mass spectrometry

Essential oil, with more than thirty kinds of compounds separated and identified by gas chromatography-mass spectrometry, was extracted from Shatian shaddock peel and Sweet shaddock peel by squeeze-steam distillation and direct steam distillation method. Among their composition, the main components are terpene compounds, which account for 93.926% (mass fraction, the same below) and 85.843% of essential oils extracted from Shatian shaddock peel and Sweet shaddock peel, respectively. Although nootkatone is the major contributor of shaddock characteristic scent, and its contents are 1.069% and 1.749% of essential oils from Sweet shaddock peel and Shatian shaddock peel, respectively. The results show that squeeze-steam distillation gives higher yield and good quality of essential oil and the compositions of essential oils from two kinds of shaddock peels are different, but the main contributors of the shaddock scent are the same.

Investment in deepwater oil and gas exploration projects:a multi-factor analysis with a real options model

Deepwater oil and gas projects embody high risks from geology and engineering aspects, which exert substantial influence on project valuation. But the uncer- tainties may be converted to additional value to the projects in the case of flexible management. Given the flexibility of project management, this paper extends the classical real options model to a multi-factor model which contains oil price, geology, and engineering uncertainties. It then gives an application example of the new model to evaluate deepwater oil and gas projects with a numerical analytical method. Compared with other methods and models, this multi-factor real options model contains more project information. It reflects the potential value deriving not only from oil price variation but also from geology and engi- neering uncertainties, which provides more accurate and reliable valuation information for decision makers.

Formation conditions and exploration direction of large natural gas reservoirs in the oil-prone Bohai Bay Basin, East China

The Bohai Bay Basin is a typical oil-prone basin, in which natural gas geological reserves have a small proportion. In this basin, the gas source rock is largely medium-deep lake mudstone with oil-prone type Ⅱ2-Ⅱ1 kerogens, and natural gas preservation conditions are poor due to active late tectonic movements. The formation conditions of large natural gas fields in the Bohai Bay Basin have been elusive. Based on the exploration results of Bohai Bay Basin and comparison with large gas fields in China and abroad, the formation conditions of conventional large-scale natural gas reservoirs in the Bohai Bay Basin were examined from accumulation dynamics, structure and sedimentation. The results show that the formation conditions of conventional large natural gas reservoirs in Bohai Bay Basin mainly include one core element and two key elements. The core factor is the strong sealing of Paleogene "quilt-like" overpressure mudstone. The two key factors include the rapid maturation and high-intensity gas generation of source rock in the late stage and large scale reservoir. On this basis, large-scale nature gas accumulation models in the Bohai Bay Basin have been worked out, including regional overpressure mudstone enriching model, local overpressure mudstone depleting model, sand-rich sedimentary subsag depleting model and late strongly-developed fault depleting model. It is found that Bozhong sag, northern Liaozhong sag and Banqiao sag have favorable conditions for the formation of large-scale natural gas reservoirs, and are worth exploring. The study results have important guidance for exploration of large scale natural gas reservoirs in the Bohai Bay Basin.

Nanopore structure comparison between shale oil and shale gas:examples from the Bakken and Longmaxi Formations

In order to analyze and compare the differences in pore structures between shale gas and shale oil formations, a few samples from the Longmaxi and Bakken Formations were collected and studied using X-ray diffraction, LECO TOC measurement, gas adsorption and field-emission scanning electron microscope. The results show that samples from the Bakken Formation have a higher TOC than those from the Longmaxi Formation. The Longmaxi Formation has higher micropore volume and larger micropore surface area and exhibited a smaller average distribution of microsize pores compared to the Bakken Formation. Both formations have similar meso-macropore volume. The Longmaxi Formation has a much larger meso-macropore surface area, which is corresponding to a smaller average meso-macropore size. CO_2 adsorption data processing shows that the pore size of the majority of the micropores in the samples from the Longmaxi Formation is less than 1 nm, while the pore size of the most of the micropores in the samples from the Bakken Formation is larger than 1 nm. Both formations have the same number of pore clusters in the 2–20 nm range, but the Bakken Formation has two additional pore size groups with mean pore size diameters larger than 20 nm. Multifractal analysis of pore size distribution curves that was derived from gas adsorption indicates that the samples from the Longmaxi Formation have more significant micropore heterogeneity and less meso-macropore heterogeneity. Abundant micropores as well as mesomacropores exist in the organic matter in the Longmaxi Formation, while the organic matter of the Bakken Formation hosts mainly micropores.

Risk measurement of international oil and gas projects based on the Value at Risk method

International oil and gas projects feature high capital-intensity, high risks and contract diversity. Therefore, in order to help decision makers make more reasonable decisions under uncertainty, it is necessary to measure the risks of international oil and gas projects. For this purpose, this paper constructs a probabilistic model that is based on the traditional economic evaluation model, and introduces value at risk(VaR) which is a valuable risk measure tool in finance, and applies Va R to measure the risks of royalty contracts, production share contracts and service contracts of an international oil and gas project. Besides, this paper compares the influences of different risk factors on the net present value(NPV) of the project by using the simulation results. The results indicate:(1) risks have great impacts on the project's NPV, therefore, if risks are overlooked, the decision may be wrong.(2) A simulation method is applied to simulate the stochastic distribution of risk factors in the probabilistic model. Therefore, the probability is related to the project's NPV, overcoming the inherent limitation of the traditional economic evaluation method.(3) VaR is a straightforward risk measure tool, and can be applied to evaluate the risks of international oil and gas projects. It is helpful for decision making.

Diffusion coefficients of natural gas in foamy oil systems under high pressures

The diffusion coefficient of natural gas in foamy oil is one of the key parameters to evaluate the feasibility of gas injection for enhanced oil recovery in foamy oil reservoirs. In this paper, a PVT cell was used to measure diffusion coefficients of natural gas in Venezuela foamy oil at high pressures, and a new method for deter- mining the diffusion coefficient in the foamy oil was de- veloped on the basis of experimental data. The effects of pressure and the types of the liquid phase on the diffusion coefficient of the natural gas were discussed. The results indicate that the diffusion coefficients of natural gas in foamy oil, saturated oil, and dead oil increase linearly with increasing pressure. The diffusion coefficient of natural gas in the foamy oil at 20 MPa was 2.93 times larger than that at 8.65 MPa. The diffusion coefficient of the natural gas in dead oil was 3.02 and 4.02 times than that of the natural gas in saturated oil and foamy oil when the pressure was 20 MPa. However, the gas content of foamy oil was 16.9 times higher than that of dead oil when the dissolution time and pressure were 20 MPa and 35.22 h, respectively.

Produced Water from Oil and Gas Exploration—Problems, Solutions and Opportunities

Large volumes of water are generated in gas- and oil-production. This includes the water that is present originally in the reservoirs, but also water that is injected into the wells. While currently much of the produced water is either reinjected or disposed of after treatment, treated produced water is increasingly seen as an interesting resource, especially in water-scarce regions. This review looks at different PW treatment methods available, with an emphasis on the management of PW in oil- and gas production on the Arabian Peninsula.

CO_2-triggered gelation for mobility control and channeling blocking during CO_2 flooding processes

CO2 flooding is regarded as an important method for enhanced oil recovery （EOR） and greenhouse gas control. However, the heterogeneity prevalently dis- tributed in reservoirs inhibits the performance of this technology. The sweep efficiency can be significantly reduced especially in the presence of ＂thief zones＂. Hence, gas channeling blocking and mobility control are important technical issues for the success of CO2 injection. Normally, crosslinked gels have the potential to block gas channels, but the gelation time control poses challenges to this method. In this study, a new method for selectively blocking CO2 channeling is proposed, which is based on a type of CO2-sensitive gel system （modified polyacry- lamide-methenamine-resorcinol gel system） to form gel in situ. A CO2-sensitive gel system is when gelation or solidification will be triggered by CO2 in the reservoir to block gas channels. The CO2-sensitivity of the gel system was demonstrated in parallel bottle tests of gel in N2 and CO2 atmospheres. Sand pack flow experiments were con- ducted to investigate the shutoff capacity of the gel system under different conditions. The injectivity of the gel system was studied via viscosity measurements. The results indi- cate that this gel system was sensitive to CO2 and had good performance of channeling blocking in porous media. Advantageous viscosity-temperature characteristics were achieved in this work. The effectiveness for EOR in heterogeneous formations based on this gel system was demonstrated using displacement tests conducted in double sand packs. The experimental results can provide guideli- nes for the deployment of theCO2-sensitive gel system for field applications.

Purification of Orange Roughy Oil

In this work, some treatments of the orange roughy oil have investigated by analysis of UV - Visible spectra and gas chromatography. When the raw oil is treated by thepartial hydrogenation under ordinary pressure at 100℃, not only the highly unsaturatcd fatty oil will be reduced partially, but also the odor and re - odor of the fish oil would be decreased.

Hydrocarbon-Generating Model of the Area Covered With Volcanic Rock

The distribution of Oil & gas fields shows their close relationship with the most active tectonic regions. This is not a coincidence but having a scientific reasons. The crustal active regions, refer to the places where the active natural earthquake, volcanic activities, underground water happened, and the areas of the leaking Off of natural gas to the surface of the crust. The magma of volcanic activities brings the organic "kitchen range body" hydrocarbon - generating model and inorganic genetic hydrocarbon to the regions covered by volcanic rock. Underground water brings a catalytic hydrocarbon generating model for organic matter, and the leaking - off of H2 and CO2 contributes a synthetic hydrocarbon - generating model. Volcanic activities bring the assemblage of Source, Reservoir and Seal formed by the sediments and magma the sedimentary basins, and the hydrocarbon - generating system with a "water - volcano" binary structure is formed. All these conditions are favorable and excellent for the formation of oil & gas fields. The distribution of AInerican oil & gas fields have very close relationship with the mines of Fe, Mn, Cr, Mo, W and V, deposits of Zn, Cu, V, Pb, Al and Hg, and the deposits of fluorite, sulfur, potassium salt, phosphate and halite, and the distribution of sulfate - chloride of river water. The reason why few oil & gas fields discovered in the regions covered by volcanic rock in western America maybe because of the view of "inconsistency between petroleum and volcano". Further more, It’s very difficult to carry out a geophysical exploration in such kinds of regions. This paper examined a few hydrocarbon - generating models (systems) mentioned above and came up with some flesh ideas on the exploration in the areas covered with volcanic rocks.

Reservoir forming conditions and key exploration technologies of Lingshui 17-2 giant gas field in deepwater area of Qiongdongnan Basin

On September 15,2014,China National Offshore Oil Co.,Ltd announced that a high production of oil and gas flow of 1.6
106 m3/d was obtained in Well LS17-2-1 in deepwater area in northern South China Sea,which is the first great oil and gas discovery for self-run deepwater exploration in China sea areas,and a strategic breakthrough was made in natural gas exploration in deepwater area of Lingshui sag in Qiongdongnan Basin.Under the combined action of climax of international deepwater exploration,high oil prices,national demands of China,practical needs of exploration,breakthroughs in seismic exploration and testing technologies,innovations in geological cognition and breakthroughs in deepwater operation equipment,Lingshui 17-2 gas field is discovered.Among these factors,the innovation in reservoir forming geological cognition directly promotes the discovery.The quality of seismic data in the early time is poor,so key reservoir forming conditions such as effective source rocks,high quality reservoirs and oil-gas migration pathways are unable to be ascertained;with support of new seismic acquisition and processing technology,some researches show that Lingshui sag is a successive large and deep sag with an area of 5000 km2 and the maximum thickness of Cenozoic stratum of 13 km.In the Early Oligocene,the Lingshui sag was a semi-closed delta-estuarine environment,where the coalmeasure and marine mudstones in Lower Oligocene Yacheng Formation were developed.The Lingshui sag is a sag with high temperature,and the bottom temperature of source rocks in Yacheng Formation can exceed 250C,but the simulation experiment of hydrocarbon generation at high temperature indicates that the main part of this set of source rock is still in the gas-generation window,with resources of nearly 1 trillion cubic meters,so the Lingshui sag is a hydrocarbon-rich generation sag.In the Neogene,the axial canyon channel from the Thu Bon River in Vietnam passed through the Lingshui sag,and five stages of secondary channels were developed in the axial canyon channel,where four types of reservoirs with excellent physical properties including the axial sand,lateral accretion sand,natural levee sand as well as erosion residual sand were developed,and lithologic traps or structural-lithologic traps were formed.The diapiric zone in the southern Lingshui sag connects deep source rocks in Yacheng Formation and shallow sandstones in the channels,and the migration pattern of natural gas is a T-type migration pattern,in other words,the natural gas generated from Yacheng Formation migrates vertically to the interior of the channel sandbody,and then migrates laterally in the channel reservoirs and forms the reservoirs.Innovations of geophysical exploration technologies for complicated geological conditions of deepwater areas are made,such as the detuning comprehensive quantitative amplitude hydrocarbon detection technology,which greatly improves the success rate of deepwater exploration;key technologies of deepwater safety exploratory well testing represented by the platform-dragged riser displacement technology are developed,which greatly reduces the drilling test cost.The above key exploration technologies provide a strong guarantee for the efficient exploration and development of Lingshui gas field.