On-Line Measurement of the Chemical Oxygen Demand in Wastewater in a Pulp and Paper Mill Using Near Infrared Spectroscopy

Although near infrared (NIR) spectroscopy has been evaluated for numerous applications, the number of actual on-line or even on-site industrial applications seems to be very limited. In the present paper, the attempts to produce online predictions of the chemical oxygen demand (COD) in wastewater from a pulp and paper mill using NIR spectroscopy are described. The task was perceived as very challenging, but with a root mean square error of prediction of 149 mg/l, roughly corresponding to 1/10 of the studied concentration interval, this attempt was deemed as successful. This result was obtained by using partial least squares model regression, interpolated reference values for calibration purposes, and by evenly distributing the calibration data in the concentration space. This work may also represent the first industrial application of online COD measurements in wastewater using NIR spectroscopy.

A METHOD OF ON-LINE MEASUREMENT FOR THE FREQUENCY RESPONSE AND IMPULSE RESPONSE FUNCTIONS OF MULTIVARIATE SYSTEM

In this paper,a method of multipoint pseudorandom combined excita-tion with the orthogonal reciprocal repeated sequences(ORRS)is presented on thebackground of the on-line identification of multivariate system.The capacity of therestraint to the identification error caused by the non-random D.C.drift of the mul-ti-input excitation with the ORRS in the multivariate system is also discussed.Thevalidity of the method described in this paper is proved by the modelling tests of themulti-plate rotor system.

On-line Temperature Rise Measurement of Submersible Motors

A new approach to the on-line temperature rise measurement of submersible pump's motors is presented. A new method of power supply and signed transmission for the measurement device in the pump well is also put forward here. The design and some experimental results are given.

Integrated On-line Instrumentation System of Magnetic Properties Measurement

A portable microcomputer-controlled inspection system has been developed for detection of magnetic properties of soft magnetic materials. It incorporates custom designed software for control of the magnetic field during operation such as demagnetization, field sweeping, and for data logging and analysis. Results are recorded using a 12-bit analog to digital converter and are then stored on disk. The magnetic hysteresis loop and Barkhausen noise data can be converted into important magnetic parameters: coecivity, remanence, and hysteresis loss, Barkhausen amplitude, and Barkhausen noise energy. This system incorporated with the magnetostriction, and magnetoacoustic emission, is then related with the nondestructive detection of material degradation.

Effects of on-line solution and off-line heat treatment on microstructure and hardness of die-cast AZ91D alloy

The effects of on-line solution, off-line solution and aging heat treatment on the microstructure and hardness of the die-cast AZ91D alloys were investigated. Brinell hardness of die-cast AZ91D alloy increases through on-line solution and off-line aging treatment but decreases after off-line solution treatment. By X-ray diffractometry, optical microscopy, differential thermal analysis, scanning electron microscopy and X-ray energy dispersive spectroscopy, it is found that the microstructures of the die-cast AZ91D magnesium alloy before and after on-line solution and off-line aging are similar, consisting of α-Mg and β-Al12Mg17. The precipitation of Al element is prevented by on-line solution so that the effect of solid solution strengthening is enhanced. The β-Al12Mg17 phases precipitate from supersaturated Mg solid solution after off-line aging treatment, and lead to microstructure refinement of AZ91D alloy, so the effect of precipitation hardening is enhanced. The β-Al12Mg17 phases dissolve in the substructure after off-line solution treatment, which leads to that the grain boundary strengthening phase is reduced significantly and the hardness of die cast AZ91D is reduced.

A Study on Comprehensive Modeling for Errors in on-line Measuring System of Machining Center

Based on the theory of multi-body system (MBS), bine’s and huston’s methods are applied to an on-line measuring system of machining center in this paper. Through the study on modeling technique, the comprehensive model for errors calculation in an on-line measuring System of machining center have been built for the first time. Using this model, the errors can be compensated by soft.ware and the measuring accuracy can be enhanced without any more inveSt. This model can be used in all kinds of machining center.

Posterior quadrantic disconnection maintains the activity of isolated temporal-parietal-occipital nerve tissue: neuroprotective measures in the surgical treatment of epilepsy

Extensive lesions involving the posterior quadrant of the cerebral hemisphere （temporal, parietal, and occipital lobes） induce intractable epilepsy. These patients are potential candidates for surgical treatmenttu. Maintenance of isolated nerve tissue activity after surgery plays a crucial role in the neuroprotective effects of neurosurgery treatment. Disconnection surgery of the posterior quadrant is used to completely isolate nerve fibers, while blood supply at the isolated lobes is maintained. Subsequently, cavities caused by cystic or necrotic nerve tissues should be reduced as much as possible,

Causes and Treatment Measures of Rural Highway Concrete Pavement Damages in Mountainous Area

Combined with the practical experience in constructing and maintenance managing the concrete pavement damage repair of Gaotang-Nenghuashan forest highway of Jiangle County,the common damage types and causes of rural highway concrete pavement in the northwestern mountainous area of Western Fujian Province were analyzed,and corresponding treatment measures to various damage were put forward.

Development of an automatic measurement system using atmospheric pressure photoionization ultrahigh-resolution mass spectrometry and application for on-line analysis of particulate matter

On-line chemical characterization of atmospheric particulate matter(PM)with soft ionization technique and ultrahigh-resolution Mass Spectrometry(UHRMS)provides molecular information of organic constituents in real time.Here we describe the development and application of an automatic measurement system that incorporates PM_(2.5)sampling,thermal desorption,atmospheric pressure photoionization,and UHRMS analysis.Molecular formulas of detected organic compounds were deducted from the accurate(±10 ppm)molecular weights obtained at a mass resolution of 100,000,allowing the identification of small organic compounds in PM_(2.5).Detection efficiencies of 28 standard compounds were determined and we found a high sensitivity and selectivity towards organic amines with limits of detection below 10 pg.As a proof of principle,PM_(2.5)samples collected off-line in winter in the urban area of Beijing were analyzed using the Ionization Module and HRMS of the system.The automatic system was then applied to conduct on-line measurements during the summer time at a time resolution of 2 hr.The detected organic compounds comprised mainly CHON and CHN compounds below 350 m/z.Pronounced seasonal variations in elemental composition were observed with shorter carbon backbones and higher O/C ratios in summer than that in winter.This result is consistent with stronger photochemical reactions and thus a higher oxidation state of organics in summer.Diurnal variation in signal intensity of each formula provides crucial information to reveal its source and formation pathway.In summary,the automatic measurement system serves as an important tool for the on-line characterization and identification of organic species in PM_(2.5).

Measurement and Analysis on Hardness and Residual Stress of Heavy Forging after Heat Treatment

The hardness and residual stress in the forging for cold roller during low temperature tempering,and the relationship of residual stress and cooling temperature of high temperature tempering for heavy forgings were studied.The stress relaxation constant at low temperature tempering and the elasto-plastisity inversion temperature at high temperature tempering were found.The results are of great importance to determine rational tempering cooling process of heavy forgings.

Why Should We Bother on Measurement in Wastewater Treatment Operation?

The question of wastewater treatment and control is reflected from a very specific viewpoint: the low priority given to accurate and useful measurements within wastewater treatment. The matter is discussed from four various perspectives, that may be labelled “Legal understanding”;“Needs for accurate measurement results already in the planning and design stage”;“The measurement problem and human behaviour”;“The understanding of the short term and long term dynamics and changes in pollution and flow loads on a wastewater treatment plant (WWTP)”. All these aspects bring about much improved needs for an accurate and frequent measurement scheme both for pollutants and flows entering a WWTP. The conclusion is stated as follows: A far more and well elaborated on-line measurement system at the plants would become a needed tool for improved water environment protection at lower costs.

Analysis and Application of the Synthetic Relative Measuring Method in On-Line Monitoring for Capacitive Equipment in Power Systems

On-line measurement for dielectric loss angle can effectively monitor the insulation condition of capacitive equipment in power systems. Synthetic relative measuring methods not only markedly overcome the shortcomings of traditional absolute measuring methods but also greatly improve the accuracy of dielectric loss angle measurement. However, synthetic relative measuring methods based on two or three pieces of capacitive equipment do not have the characteristic of generality. In this paper, a principle of synthetic relative measuring method is presented. The example of application for synthetic relative methods based on three and four pieces of capacitive equipment running in the same phase is taken to present the failure judgment matrices for N pieces of equipment. According to these matrices, the fault condition of N pieces of capacitive equipment can be watched, which is more general. Then some problems needing to be concerned along with two diagnostic methods used in diagnostic system are introduced. Finally, two programmable flow charts for the two methods are given and corresponding examples demonstrate their feasibility in practice.

Interpretation of diagnosis and treatment scheme of COVID-19 in Hunan province (the third trial version) based on three factors and measures

The similarities and differences between"Novel Coronavirus Infected pneumonia in Hunan province(trial second edition)"and"Novel Coronavirus Infected pneumonia(Trial seventh edition)"released by the National Health Commission and their ideas were interpreted based on"suiting measures to three factors".①In Hunan program,the third version of the trial adjustment more suitable for local characteristics of the disease;②The prevention program population classification is clear,support,eliminate pathogenic factors of the primary and secondary distinct;③The cause of disease is prominent,damp and toxin are mixed with dryness,and the treatment is mainly to moisten the lung and clear away heat,and the prescription is mostly Xinliang light agent.

Tracking Galloping Profile of Transmission Lines Using Wireless Inertial Measurement Units

Galloping of power transmission lines might bring about huge damage such as massive power outage and collapse of the transmission towers. To realize forecast of the galloping and provide data for study on the galloping mechanism, this paper proposes an online monitoring system for tracking galloping profile of power transmission lines based on wireless inertial measurement units (WIMUs). The system is composed of three modules: wireless inertial measurement nodes, monitoring base station, and remote monitoring station. After detailing the hardware system, the corresponding software which positions and displays galloping profile of the transmission line in real-time is outlined. The feasibility of the proposed on-line monitoring system is demonstrated through a series of experiments at the State Grid Key Laboratory of Power Overhead Transmission Line Galloping (Zhengzhou, China) by taking into account different vibration patterns.

A real-time measuring technology for studying distortion of hydraulic turbine blade castings during heat treatment process

During heat treatment process, the distortion behavior inevitably appears in hydraulic turbine blade castings. In this research, a technology was developed for real-time measurement of the distortion in hydraulic turbine blade castings at the still air cooling and forced air cooling stages during heat treatment process. The method was used to measure the distortion behavior at the cooling stages in both normalizing and tempering processes. At the normalization, the distortion at the blade comer near outlet side undergoes four stages with alternating bending along positive and negative directions. At the tempering stage, the distortion could be divided into two steps. The temperature difference between the two surfaces of blade casting was employed to analyze the distortion mechanism. The measured results could be applied to guide the production, and the machining allowance could be reduced by controlling the distortion behavior.

ON-LINE INSPECTION TECHNIQUES OF MANUFACTURING QUALITY OF ROLLED-STEEL SHEET

On-line measurement of manufaturing quality of rolled steel needs the performances of noncontact, high-responds, high-resolution and high aceuracy. The reccntly developed hardware makes it possible. This paper gives a review of the development of this techniques and introduces four kinds of developed measurement systems. And the future development trends in this field was also discussed.

The Measurement and Control of Diameter in Large-Scale Part Processing

Based on laser-scanned measuring technology, a met ho d of on-line dynamic non-contact measurement and feedback control of processin g dimension, i.e. the double edges laser-scanned large diameter on-line dynami c measurement and control system is presented, which can be used to measure diam eter in large-scale machine part processing. In this paper, the working princip le, overall structure and microcomputer real-time control and data processing s ystem of the system are discussed in detail, the method of double edges scanned large diameter dimension measurement and control is theoretically analyzed, its possibility has been verified by experiments of lathing large diameters machine parts by a vertical lathe. The system adopts the measuring scheme of double edge s laser-scanned combined with grating displacement measurement. The two edges c haracteristic information of the measured diameter is given by the double edges laser-scanned measuring system, the non-contact measurement of large diameter dimension is realized to combine with the grating displacement measuring systems . The main controller gives out feedback control signal by means of measured res ults, and controls advance and retreat of lathe tool by the servo-control syste m of a vertical lathe to realize on-line dynamic non-contact measurement and c ontrol in processing.

Measurement of Particle Velocity, Particle Size Distribution and Concentration in Particulate Suspension by Transmission Fluctuation Correlation Spectrometry

In coal-fired power generation industry, parameters such as particle size affect combustion efficiency. Especially in the application of two-phase flow clean energy, the parameters such as particle velocity, particle size distribution and concentration are very important, because the coal particle velocity, concentration or size range have an impact on the whole combustion process. This paper introduces an optical measurement setup based on the transmission fluctuation correlation spectrum measurement technique, which realizes the simultaneous measurement of particle velocity, particle size distribution and concentration. Compared with image method, ultrasonic spectrum method and other methods, the experimental device is simple and low-cost.

External validation of the Moroccan Arabic version of the European Organization for Research and Treatment of Cancer colorectal(CR29)module:Monocentric study

BACKGROUND Quality of life(QoL)outcomes are a focal endpoint of cancer treatment strategies.AIM To externally validate the Moroccan Arabic version of the European Organization for Research and Treatment of Cancer(EORTC)QoL Questionnaire(QLQ)for colorectal cancer(CRC)patients(CR29).METHODS Both Moroccan Arabic modules of QLQ-CR29 and QLQ-C30 were administered to Moroccan CRC.Psychometric properties were retested by measuring Cronbach’s alpha coefficient for reliability and Intraclass correlation coefficient(ICC)to examine test-retest reproducibility.The multitrait-scaling analysis was performed to demonstrate the validity of the instrument and known-groups comparison was used to test the score’s ability to discriminate between different groups of patients.RESULTS In total,221 patients were included in our study and 34 patients completed the questionnaire twice.The Urinary Frequency scale and Stool Frequency scale had good internal consistency with alpha Cronbach coefficients of 0.79 and 0.83 respectively,while the same coefficients were moderately lower for the Blood and Mucus in Stool scale(0.61)and the Body Image scale(0.67).The ICCs ranged from 0.88 to 1 indicating good to excellent reproducibility.In multitrait scaling analyses,the criterion for item convergent and divergent validity was satisfactory.The known-group comparison showed statistically significant differences between patients according to age,gender,stoma status,tumor location,and radiotherapy.CONCLUSION The Moroccan Arabic version of the EORTC QLQ-CR29 is a valid and reliable tool that can be used safely for research and clinical purposes in Moroccan CRC patients.

钓鱼台隧道洞口崩塌成因分析与处治措施研究

对池祁高速钓鱼台隧道洞口大型崩塌的成因进行了深入分析,提出了相应的崩塌处治措施,并通过现场监测分析对崩塌处治效果进行了验证。研究结果表明,钓鱼台隧道洞口崩塌是地形、地质、降雨、施工措施不当等多种因素共同作用的结果,其中地形和地质条件是形成崩塌的内因,降雨和施工措施不当等因素是诱发崩塌的外因。基于以上影响因素并结合隧道洞口实际情况,提出了“临时支护+永久性防护”的综合处治方案,即采用洞内背拱加固、掌子面反压回填、崩塌体卸载、洞口双层小导管支护、接长明洞以及洞顶仰坡锚杆框架防护的方案。现场巡视与监测数据表明,隧道洞口崩塌处治措施得当,工程效果显著,实现了预期目的。