Dynamic soaring,which harvests energy from the wind,can enhance Unmanned Aerial Vehicles'(UAVs')range and endurance.However,energy harvesting efficiency issues hinder UAV applications,which can be addressed by...Dynamic soaring,which harvests energy from the wind,can enhance Unmanned Aerial Vehicles'(UAVs')range and endurance.However,energy harvesting efficiency issues hinder UAV applications,which can be addressed by wing morphing.Therefore,this study investigates the influence of albatross wing morphing during dynamic soaring.By constructing a parametric model,the shape of the albatross wing can be modeled and achieve morphing based on joints.From the video data,this paper summarizes the typical wing morphing patterns of the albatross and notices that changes primarily occur during the leeward descent phase.This paper first analyzes the aerodynamic performance of different wing morphing patterns and finds that the drag coefficient can be reduced by 7.75%with a suitable morphing pattern.This paper also explores the drag coefficient reduction mechanism and finds that downwash airflow decreases by 30.32%after wingtip anhedral.Interestingly,the lift-to-drag ratio shows minimal variation under different morphing patterns,within 2%.From the stability perspective,this study finds that the neutral point position changes after morphing.The maximum longitudinal static margin change is 4.9%,enhancing longitudinal stability by increasing the restorative moment arm.The lateral neutral point is 4.87%closer to the center of gravity,decreasing the roll and yaw moments.It can be observed that wingtip anhedral significantly increases the stability of the albatross.Moreover,a flight simulation is carried out to study the morphing influence on trajectory and energy harvesting.The results show that maximum energy gained is improved by 47.99%,and endurance is increased by 13.05%.The results also indicate that the effects of wing morphing are global rather than limited to the phase of morphing occurrence.Finally,based on the results,this paper proposes wing morphing regularity about the wingtip for UAVs.Wingtip bends downward can significantly increase the UAVs'stability and reduce drag,but the overall trajectory needs to be reconsidered after introducing wing morphing.展开更多
Achieving the detachment of divertor can help to alleviate excessive heat load and sputtering problems on the target plates,thereby extending the lifetime of divertor components for fusion devices.In order to provide ...Achieving the detachment of divertor can help to alleviate excessive heat load and sputtering problems on the target plates,thereby extending the lifetime of divertor components for fusion devices.In order to provide a fast but relatively reliable prediction of plasma parameters along the flux tube for future device design,a one-dimensional(1D)modeling code for the operating point of impurity seeded detached divertor is developed based on Python language,which is a fluid model based on previous work(Plasma Phys.Control.Fusion 58045013(2016)).The experimental observation of the onset of divertor detachment by neon(Ne)and argon(Ar)seeding in EAST is well reproduced by using the 1D modeling code.The comparison between the 1D modeling and two-dimensional(2D)simulation by the SOLPS-ITER code for CFETR detachment operation with Ne and Ar seeding also shows that they are in good agreement.We also predict the radiative power loss and corresponding impurity concentration requirement for achieving divertor detachment via different impurity seeding under high heating power conditions in EAST and CFETR phase II by using the 1D model.Based on the predictions,the optimized parameter space for divertor detachment operation on EAST and CFETR is also determined.Such a simple but reliable 1D model can provide a reasonable parameter input for a detailed and accurate analysis by 2D or three-dimensional(3D)modeling tools through rapid parameter scanning.展开更多
Roxarsone(ROX)is a commonly used antibacterial and growth-promoting additive to animal feed.The development of an effective method for detecting ROX and its conversion products is of importance because of their potent...Roxarsone(ROX)is a commonly used antibacterial and growth-promoting additive to animal feed.The development of an effective method for detecting ROX and its conversion products is of importance because of their potential harm to human health and ecosystem.Herein,we report the designed synthesis of a novel one-dimensional covalent organic framework(1D COF),named EP-COF,and its application as a fluorescent probe for ROX sensing.EP-COF is constructed based on imine linkages,exhibiting high crystallinity,strong fluorescence emission,and good dispersibility in water.It displays a remarkable capability to efficiently detect ROX,with an impressive detection limit of 4.5 nmol/L.Moreover,EP-COF also offers advantages of excellent selectivity,and high structural stability.This work not only presents a promising approach for the detection of harmful substances like ROX,but also serves as a valuable reference for exploring application of 1D COFs in chemical sensing.展开更多
In this paper,numerical experiments are carried out to investigate the impact of penalty parameters in the numerical traces on the resonance errors of high-order multiscale discontinuous Galerkin(DG)methods(Dong et al...In this paper,numerical experiments are carried out to investigate the impact of penalty parameters in the numerical traces on the resonance errors of high-order multiscale discontinuous Galerkin(DG)methods(Dong et al.in J Sci Comput 66:321–345,2016;Dong and Wang in J Comput Appl Math 380:1–11,2020)for a one-dimensional stationary Schrödinger equation.Previous work showed that penalty parameters were required to be positive in error analysis,but the methods with zero penalty parameters worked fine in numerical simulations on coarse meshes.In this work,by performing extensive numerical experiments,we discover that zero penalty parameters lead to resonance errors in the multiscale DG methods,and taking positive penalty parameters can effectively reduce resonance errors and make the matrix in the global linear system have better condition numbers.展开更多
Mud is a ubiquitous building material in Nigeria,perhaps this is the reason why it is hardly seen as the outright building material that it is.The most popular contribution of mud to Nigerian architecture can only be ...Mud is a ubiquitous building material in Nigeria,perhaps this is the reason why it is hardly seen as the outright building material that it is.The most popular contribution of mud to Nigerian architecture can only be seen in the ancient traditional huts all over the country.Although still a building material in the suburbs of the country,mud is seen as a relic of the past,a symbol of a primitive tale of Nigerian building construction.The primary effort here is to redefine mud as a“skin”with infinite possibilities of imagery and texture,rather than its typical application as a wall in Nigerian architecture.Mud is attempted to be expressed via a new geometric vocabulary by re-evaluating its surreptitious properties including its ability to behave like a formally defined NURBS(non-uniform rational basis spline)surface.The properties of mud and clay are unconventionally simulated in computer modelling and analysis software to understand the ways in which it can be optimized for advanced building applications.Streamlined calculations and algorithmic calculations serve as tools to discover the NURBS-propensity of mud.This provides a whole new low-cost construction opportunity for the building of irregularly flowing structures.展开更多
Searching for one-dimensional(1D)nanostructure with ferromagnetic(FM)half-metallicity is of significance for the development of miniature spintronic devices.Here,based on the first-principles calculations,we propose t...Searching for one-dimensional(1D)nanostructure with ferromagnetic(FM)half-metallicity is of significance for the development of miniature spintronic devices.Here,based on the first-principles calculations,we propose that the 1D CrN nanostructure is a FM half-metal,which can generate the fully spin-polarized current.The ab initio molecular dynamic simulation and the phonon spectrum calculation demonstrate that the 1D CrN nanostructure is thermodynamically stable.The partially occupied Cr-d orbitals endow the nanostructure with FM half-metallicity,in which the half-metallic gap(?s)reaches up to 1.58 eV.The ferromagnetism in the nanostructure is attributed to the superexchange interaction between the magnetic Cr atoms,and a sizable magnetocrystalline anisotropy energy(MAE)is obtained.Moreover,the transverse stretching of nanostructure can effectively modulate?s and MAE,accompanied by the preservation of half-metallicity.A nanocable is designed by encapsulating the CrN nanostructure with a BN nanotube,and the intriguing magnetic and electronic properties of the nanostructure are retained.These novel characteristics render the 1D CrN nanostructure as a compelling candidate for exploiting high-performance spintronic devices.展开更多
Raptors are getting more attention from researchers because of their excellent flight abilities.And the excellent wing morphing ability is critical for raptors to achieve high maneuvering flight,which can be a good bi...Raptors are getting more attention from researchers because of their excellent flight abilities.And the excellent wing morphing ability is critical for raptors to achieve high maneuvering flight,which can be a good bionic inspiration for unmanned aerial vehicles(UAV)design.However,morphing wing motions of Falco peregrinus with multi postures cannot be consulted since such a motion database was nonexistent.This study aimed to provide data reference for future research in wing morphing kinetics.We used the computed tomography(CT)approach to obtain nine critical postures of the Falco peregrinus wing skeleton,followed with motion analysis of each joint and bone.Based on the obtained motion database,a six-bar kinematic model was proposed to regenerate wing motions with a high fidelity.展开更多
This paper proposes an adaptive neural control(ANC)method for the coupled nonlinear model of a novel type of embedded surface morphing aircraft which has a tiltable V-tail.A nonlinear model with sixdegrees-of-freedom ...This paper proposes an adaptive neural control(ANC)method for the coupled nonlinear model of a novel type of embedded surface morphing aircraft which has a tiltable V-tail.A nonlinear model with sixdegrees-of-freedom is established.The first-order sliding mode differentiator(FSMD)is applied to the control scheme to avoid the problem of“differential explosion”.Radial basis function neural networks are introduced to estimate the uncertainty and external disturbance of the model,and an ANC controller is proposed based on this design idea.The stability of the proposed ANC controller is proved using Lyapunov theory,and the tracking error of the closed-loop system is semi-globally uniformly bounded.The effectiveness and robustness of the proposed method are verified by numerical simulations and hardware-in-the-loop(HIL)simulations.展开更多
Periodic photonic structures can provide rich modulation in propagation of light due to well-defined band structures.Especially near band edges,light localization and the effect of near-zero refractive index have attr...Periodic photonic structures can provide rich modulation in propagation of light due to well-defined band structures.Especially near band edges,light localization and the effect of near-zero refractive index have attracted wide attention.However,the practically fabricated structures can only have finite size,i.e.,limited numbers of periods,leading to changes of the light propagation modulation compared with infinite structures.Here,we study the size effect on light localization and near-zero refractive-index propagation near band edges in one-dimensional periodic structures.Near edges of the band gap,as the structure's size shrinks,the broadening of the band gap and the weakening of the light localization are discovered.When the size is small,an added layer on the surface will perform large modulation in the group velocity.Near the degenerate point with Dirac-like dispersion,the zero-refractive-index effects like the zero-phase difference and near-unity transmittance retain as the size changes,while absolute group velocity fluctuates when the size shrinks.展开更多
Aluminum nitride (AIN) nanowires, serrated nanoribbons, and nanoribbons were selectively obtained through a simple chloride assisted chemical vapor deposition process. The morphologies of the products could be contr...Aluminum nitride (AIN) nanowires, serrated nanoribbons, and nanoribbons were selectively obtained through a simple chloride assisted chemical vapor deposition process. The morphologies of the products could be controlled by adjusting the deposition position and the flux of the reactant gas. The morphologies and structures of the AIN products were investigated in detail. The formation mechanism of the as-prepared different morphologies of AIN one-dimensional (ID) nanostructures was discussed on the basis of the experimental results.展开更多
By means of Muskhelishvili’s method and the technique of generalized conformal mapping,the physical plane problems are transformed into regular mathematical problems in quasicrystals(QCs).The analytical solution to a...By means of Muskhelishvili’s method and the technique of generalized conformal mapping,the physical plane problems are transformed into regular mathematical problems in quasicrystals(QCs).The analytical solution to an elliptical orifice problem with asymmetric cracks in one-dimensional(1D)orthorhombic QCs is obtained.By using the Dugdale-Barenblatt model,the plastic simulation at the crack tip of the elliptical orifice with asymmetric cracks in 1D orthorhombic QCs is performed.Finally,the size of the atomic cohesive force zone is determined precisely,and the size of the atomic cohesive force zone around the crack tip of an elliptical orifice with a single crack or two symmetric cracks is obtained.展开更多
Ultrasonic guided wave is an attractive monitoring technique for large-scale structures but is vulnerable to changes in environmental and operational conditions(EOC),which are inevitable in the normal inspection of ci...Ultrasonic guided wave is an attractive monitoring technique for large-scale structures but is vulnerable to changes in environmental and operational conditions(EOC),which are inevitable in the normal inspection of civil and mechanical structures.This paper thus presents a robust guided wave-based method for damage detection and localization under complex environmental conditions by singular value decomposition-based feature extraction and one-dimensional convolutional neural network(1D-CNN).After singular value decomposition-based feature extraction processing,a temporal robust damage index(TRDI)is extracted,and the effect of EOCs is well removed.Hence,even for the signals with a very large temperature-varying range and low signal-to-noise ratios(SNRs),the final damage detection and localization accuracy retain perfect 100%.Verifications are conducted on two different experimental datasets.The first dataset consists of guided wave signals collected from a thin aluminum plate with artificial noises,and the second is a publicly available experimental dataset of guided wave signals acquired on a composite plate with a temperature ranging from 20℃to 60℃.It is demonstrated that the proposed method can detect and localize the damage accurately and rapidly,showing great potential for application in complex and unknown EOC.展开更多
The dynamical behavior of real-world phenomena is implausible graphically due to the complexity of mathematical coding. The present article has mainly focused on some one-dimensional real maps’ dynamical behavior irr...The dynamical behavior of real-world phenomena is implausible graphically due to the complexity of mathematical coding. The present article has mainly focused on some one-dimensional real maps’ dynamical behavior irrespective of using coding. In continuation, linear, quadratic, cubic, higher-order, exponential, logarithmic, and absolute value maps have been used to scrutinize their dynamical behavior, including the characteristics of the orbit of points. Dynamical programming software (DPS.exe) will be proposed as a new technique to ascertain the dynamical behavior of said maps. Thus, a mathematician can automatically determine one-dimensional real maps’ dynamical behavior apart from complicated programming code and analytical solutions.展开更多
In this paper,we investigate the interfacial behavior of a thin one-dimensional(1D)hexagonal quasicrystal(QC)film bonded on an elastic substrate subjected to a mismatch strain due to thermal variation.The contact inte...In this paper,we investigate the interfacial behavior of a thin one-dimensional(1D)hexagonal quasicrystal(QC)film bonded on an elastic substrate subjected to a mismatch strain due to thermal variation.The contact interface is assumed to be nonslipping,with both perfectly bonded and debonded boundary conditions.The Fourier transform technique is adopted to establish the integral equations in terms of interfacial shear stress,which are solved as a linear algebraic system by approximating the unknown phonon interfacial shear stress via the series expansion of the Chebyshev polynomials.The expressions are explicitly obtained for the phonon interfacial shear stress,internal normal stress,and stress intensity factors(SIFs).Finally,based on numerical calculations,we briefly discuss the effects of the material mismatch,the geometry of the QC film,and the debonded length and location on stresses and SIFs.展开更多
基金sponsored by Innovation Foundation for Doctor Dissertation of Northwestern Polytechnical University,China(No.CX2024037)。
文摘Dynamic soaring,which harvests energy from the wind,can enhance Unmanned Aerial Vehicles'(UAVs')range and endurance.However,energy harvesting efficiency issues hinder UAV applications,which can be addressed by wing morphing.Therefore,this study investigates the influence of albatross wing morphing during dynamic soaring.By constructing a parametric model,the shape of the albatross wing can be modeled and achieve morphing based on joints.From the video data,this paper summarizes the typical wing morphing patterns of the albatross and notices that changes primarily occur during the leeward descent phase.This paper first analyzes the aerodynamic performance of different wing morphing patterns and finds that the drag coefficient can be reduced by 7.75%with a suitable morphing pattern.This paper also explores the drag coefficient reduction mechanism and finds that downwash airflow decreases by 30.32%after wingtip anhedral.Interestingly,the lift-to-drag ratio shows minimal variation under different morphing patterns,within 2%.From the stability perspective,this study finds that the neutral point position changes after morphing.The maximum longitudinal static margin change is 4.9%,enhancing longitudinal stability by increasing the restorative moment arm.The lateral neutral point is 4.87%closer to the center of gravity,decreasing the roll and yaw moments.It can be observed that wingtip anhedral significantly increases the stability of the albatross.Moreover,a flight simulation is carried out to study the morphing influence on trajectory and energy harvesting.The results show that maximum energy gained is improved by 47.99%,and endurance is increased by 13.05%.The results also indicate that the effects of wing morphing are global rather than limited to the phase of morphing occurrence.Finally,based on the results,this paper proposes wing morphing regularity about the wingtip for UAVs.Wingtip bends downward can significantly increase the UAVs'stability and reduce drag,but the overall trajectory needs to be reconsidered after introducing wing morphing.
基金Project supported by the National Key Research and Development Program of China (Grant No.2022YFE03030001)the National Natural Science Foundation of China (Grant No.12075283)。
文摘Achieving the detachment of divertor can help to alleviate excessive heat load and sputtering problems on the target plates,thereby extending the lifetime of divertor components for fusion devices.In order to provide a fast but relatively reliable prediction of plasma parameters along the flux tube for future device design,a one-dimensional(1D)modeling code for the operating point of impurity seeded detached divertor is developed based on Python language,which is a fluid model based on previous work(Plasma Phys.Control.Fusion 58045013(2016)).The experimental observation of the onset of divertor detachment by neon(Ne)and argon(Ar)seeding in EAST is well reproduced by using the 1D modeling code.The comparison between the 1D modeling and two-dimensional(2D)simulation by the SOLPS-ITER code for CFETR detachment operation with Ne and Ar seeding also shows that they are in good agreement.We also predict the radiative power loss and corresponding impurity concentration requirement for achieving divertor detachment via different impurity seeding under high heating power conditions in EAST and CFETR phase II by using the 1D model.Based on the predictions,the optimized parameter space for divertor detachment operation on EAST and CFETR is also determined.Such a simple but reliable 1D model can provide a reasonable parameter input for a detailed and accurate analysis by 2D or three-dimensional(3D)modeling tools through rapid parameter scanning.
基金the Science and Technology Commission of Shanghai Municipality(No.20JC1415400)for financial support。
文摘Roxarsone(ROX)is a commonly used antibacterial and growth-promoting additive to animal feed.The development of an effective method for detecting ROX and its conversion products is of importance because of their potential harm to human health and ecosystem.Herein,we report the designed synthesis of a novel one-dimensional covalent organic framework(1D COF),named EP-COF,and its application as a fluorescent probe for ROX sensing.EP-COF is constructed based on imine linkages,exhibiting high crystallinity,strong fluorescence emission,and good dispersibility in water.It displays a remarkable capability to efficiently detect ROX,with an impressive detection limit of 4.5 nmol/L.Moreover,EP-COF also offers advantages of excellent selectivity,and high structural stability.This work not only presents a promising approach for the detection of harmful substances like ROX,but also serves as a valuable reference for exploring application of 1D COFs in chemical sensing.
基金supported by the National Science Foundation grant DMS-1818998.
文摘In this paper,numerical experiments are carried out to investigate the impact of penalty parameters in the numerical traces on the resonance errors of high-order multiscale discontinuous Galerkin(DG)methods(Dong et al.in J Sci Comput 66:321–345,2016;Dong and Wang in J Comput Appl Math 380:1–11,2020)for a one-dimensional stationary Schrödinger equation.Previous work showed that penalty parameters were required to be positive in error analysis,but the methods with zero penalty parameters worked fine in numerical simulations on coarse meshes.In this work,by performing extensive numerical experiments,we discover that zero penalty parameters lead to resonance errors in the multiscale DG methods,and taking positive penalty parameters can effectively reduce resonance errors and make the matrix in the global linear system have better condition numbers.
文摘Mud is a ubiquitous building material in Nigeria,perhaps this is the reason why it is hardly seen as the outright building material that it is.The most popular contribution of mud to Nigerian architecture can only be seen in the ancient traditional huts all over the country.Although still a building material in the suburbs of the country,mud is seen as a relic of the past,a symbol of a primitive tale of Nigerian building construction.The primary effort here is to redefine mud as a“skin”with infinite possibilities of imagery and texture,rather than its typical application as a wall in Nigerian architecture.Mud is attempted to be expressed via a new geometric vocabulary by re-evaluating its surreptitious properties including its ability to behave like a formally defined NURBS(non-uniform rational basis spline)surface.The properties of mud and clay are unconventionally simulated in computer modelling and analysis software to understand the ways in which it can be optimized for advanced building applications.Streamlined calculations and algorithmic calculations serve as tools to discover the NURBS-propensity of mud.This provides a whole new low-cost construction opportunity for the building of irregularly flowing structures.
基金the National Natural Science Foundation of China(Grant Nos.12004137,62071200,and 12104236)Shandong Provincial Natural Science Foundation of China(Grant Nos.ZR2020QA052,ZR2020ZD28,ZR2021MA040,and ZR2021MA060).
文摘Searching for one-dimensional(1D)nanostructure with ferromagnetic(FM)half-metallicity is of significance for the development of miniature spintronic devices.Here,based on the first-principles calculations,we propose that the 1D CrN nanostructure is a FM half-metal,which can generate the fully spin-polarized current.The ab initio molecular dynamic simulation and the phonon spectrum calculation demonstrate that the 1D CrN nanostructure is thermodynamically stable.The partially occupied Cr-d orbitals endow the nanostructure with FM half-metallicity,in which the half-metallic gap(?s)reaches up to 1.58 eV.The ferromagnetism in the nanostructure is attributed to the superexchange interaction between the magnetic Cr atoms,and a sizable magnetocrystalline anisotropy energy(MAE)is obtained.Moreover,the transverse stretching of nanostructure can effectively modulate?s and MAE,accompanied by the preservation of half-metallicity.A nanocable is designed by encapsulating the CrN nanostructure with a BN nanotube,and the intriguing magnetic and electronic properties of the nanostructure are retained.These novel characteristics render the 1D CrN nanostructure as a compelling candidate for exploiting high-performance spintronic devices.
基金supported by the National Natural Science Foundation of China(Grant Nos.52175279,52075489,and 51705459)the Natural Science Foundation of Zhejiang Province,China(Grant Nos.LY20E050022 and LGG20E050017)。
文摘Raptors are getting more attention from researchers because of their excellent flight abilities.And the excellent wing morphing ability is critical for raptors to achieve high maneuvering flight,which can be a good bionic inspiration for unmanned aerial vehicles(UAV)design.However,morphing wing motions of Falco peregrinus with multi postures cannot be consulted since such a motion database was nonexistent.This study aimed to provide data reference for future research in wing morphing kinetics.We used the computed tomography(CT)approach to obtain nine critical postures of the Falco peregrinus wing skeleton,followed with motion analysis of each joint and bone.Based on the obtained motion database,a six-bar kinematic model was proposed to regenerate wing motions with a high fidelity.
基金funded by the National Natural Science Foundation of China(No.61573286)the Natural Science Foundation of Shaanxi Province(2019JM-163,2020JQ-218)+1 种基金the Fundamental Research Funds for the Central Universities(3102019ZDHKY07)supported by Shaanxi Province Key Laboratory of Flight Control and Simulation Technology。
文摘This paper proposes an adaptive neural control(ANC)method for the coupled nonlinear model of a novel type of embedded surface morphing aircraft which has a tiltable V-tail.A nonlinear model with sixdegrees-of-freedom is established.The first-order sliding mode differentiator(FSMD)is applied to the control scheme to avoid the problem of“differential explosion”.Radial basis function neural networks are introduced to estimate the uncertainty and external disturbance of the model,and an ANC controller is proposed based on this design idea.The stability of the proposed ANC controller is proved using Lyapunov theory,and the tracking error of the closed-loop system is semi-globally uniformly bounded.The effectiveness and robustness of the proposed method are verified by numerical simulations and hardware-in-the-loop(HIL)simulations.
基金the National Key Basic Research Program of China(Grant No.2022YFA1404800)the National Natural Science Foundation of China(Grant Nos.12234007 and 12221004)supported by Science and Technology Commission of Shanghai Municipality,China(Grant Nos.19XD1434600,2019SHZDZX01,19DZ2253000,20501110500,and 21DZ1101500)。
文摘Periodic photonic structures can provide rich modulation in propagation of light due to well-defined band structures.Especially near band edges,light localization and the effect of near-zero refractive index have attracted wide attention.However,the practically fabricated structures can only have finite size,i.e.,limited numbers of periods,leading to changes of the light propagation modulation compared with infinite structures.Here,we study the size effect on light localization and near-zero refractive-index propagation near band edges in one-dimensional periodic structures.Near edges of the band gap,as the structure's size shrinks,the broadening of the band gap and the weakening of the light localization are discovered.When the size is small,an added layer on the surface will perform large modulation in the group velocity.Near the degenerate point with Dirac-like dispersion,the zero-refractive-index effects like the zero-phase difference and near-unity transmittance retain as the size changes,while absolute group velocity fluctuates when the size shrinks.
基金the National Natural Science Foundation of China under grant Nos.10674138 and 20571022.
文摘Aluminum nitride (AIN) nanowires, serrated nanoribbons, and nanoribbons were selectively obtained through a simple chloride assisted chemical vapor deposition process. The morphologies of the products could be controlled by adjusting the deposition position and the flux of the reactant gas. The morphologies and structures of the AIN products were investigated in detail. The formation mechanism of the as-prepared different morphologies of AIN one-dimensional (ID) nanostructures was discussed on the basis of the experimental results.
基金Project supported by the National Natural Science Foundation of China(Nos.12162027 and 11962026)the Natural Science Key Project of Science and Technology Research in Higher Education Institutions of Inner Mongolia Autonomous Region(No.NJZZ22574)。
文摘By means of Muskhelishvili’s method and the technique of generalized conformal mapping,the physical plane problems are transformed into regular mathematical problems in quasicrystals(QCs).The analytical solution to an elliptical orifice problem with asymmetric cracks in one-dimensional(1D)orthorhombic QCs is obtained.By using the Dugdale-Barenblatt model,the plastic simulation at the crack tip of the elliptical orifice with asymmetric cracks in 1D orthorhombic QCs is performed.Finally,the size of the atomic cohesive force zone is determined precisely,and the size of the atomic cohesive force zone around the crack tip of an elliptical orifice with a single crack or two symmetric cracks is obtained.
基金Supported by National Natural Science Foundation of China(Grant Nos.52272433 and 11874110)Jiangsu Provincial Key R&D Program(Grant No.BE2021084)Technical Support Special Project of State Administration for Market Regulation(Grant No.2022YJ11).
文摘Ultrasonic guided wave is an attractive monitoring technique for large-scale structures but is vulnerable to changes in environmental and operational conditions(EOC),which are inevitable in the normal inspection of civil and mechanical structures.This paper thus presents a robust guided wave-based method for damage detection and localization under complex environmental conditions by singular value decomposition-based feature extraction and one-dimensional convolutional neural network(1D-CNN).After singular value decomposition-based feature extraction processing,a temporal robust damage index(TRDI)is extracted,and the effect of EOCs is well removed.Hence,even for the signals with a very large temperature-varying range and low signal-to-noise ratios(SNRs),the final damage detection and localization accuracy retain perfect 100%.Verifications are conducted on two different experimental datasets.The first dataset consists of guided wave signals collected from a thin aluminum plate with artificial noises,and the second is a publicly available experimental dataset of guided wave signals acquired on a composite plate with a temperature ranging from 20℃to 60℃.It is demonstrated that the proposed method can detect and localize the damage accurately and rapidly,showing great potential for application in complex and unknown EOC.
文摘The dynamical behavior of real-world phenomena is implausible graphically due to the complexity of mathematical coding. The present article has mainly focused on some one-dimensional real maps’ dynamical behavior irrespective of using coding. In continuation, linear, quadratic, cubic, higher-order, exponential, logarithmic, and absolute value maps have been used to scrutinize their dynamical behavior, including the characteristics of the orbit of points. Dynamical programming software (DPS.exe) will be proposed as a new technique to ascertain the dynamical behavior of said maps. Thus, a mathematician can automatically determine one-dimensional real maps’ dynamical behavior apart from complicated programming code and analytical solutions.
基金Project supported by the National Natural Science Foundation of China(Nos.11572289,1171407,11702252,and 11902293)the China Postdoctoral Science Foundation(No.2019M652563)。
文摘In this paper,we investigate the interfacial behavior of a thin one-dimensional(1D)hexagonal quasicrystal(QC)film bonded on an elastic substrate subjected to a mismatch strain due to thermal variation.The contact interface is assumed to be nonslipping,with both perfectly bonded and debonded boundary conditions.The Fourier transform technique is adopted to establish the integral equations in terms of interfacial shear stress,which are solved as a linear algebraic system by approximating the unknown phonon interfacial shear stress via the series expansion of the Chebyshev polynomials.The expressions are explicitly obtained for the phonon interfacial shear stress,internal normal stress,and stress intensity factors(SIFs).Finally,based on numerical calculations,we briefly discuss the effects of the material mismatch,the geometry of the QC film,and the debonded length and location on stresses and SIFs.