Surface Metallization of Glass Fiber(GF)/Polyetheretherketone(PEEK) Composite with Cu Coatings Deposited by Magnetron Sputtering and Electroplating

Surface metallization of glass fiber(GF)/polyetheretherketone(PEEK)[GF/PEEK] is conducted by coating copper using electroplating and magnetron sputtering and the properties are determined by X-ray diffraction(XRD), scanning electron microscopy(SEM), and electron backscatter diffraction(EBSD).The coating bonding strength is assessed by pull-out tests and scribing in accordance with GB/T 9286-1998.The results show that the Cu coating with a thickness of 30 μm deposited on GF/PEEK by magnetron sputtering has lower roughness, finer grain size, higher crystallinity, as well as better macroscopic compressive stress,bonding strength, and electrical conductivity than the Cu coating deposited by electroplating.

One-step quantum dialogue

Quantum dialogue(QD)enables two communication parties to directly exchange secret messages simultaneously.In conventional QD protocols,photons need to transmit in the quantum channel for two rounds.In this paper,we propose a one-step QD protocol based on the hyperentanglement.With the help of the non-local hyperentanglement-assisted Bell state measurement(BSM),the photons only need to transmit in the quantum channel once.We prove that our one-step QD protocol is secure in theory and numerically simulate its secret message capacity under practical experimental condition.Compared with previous QD protocols,the one-step QD protocol can effectively simplify the experiment operations and reduce the message loss caused by the photon transmission loss.Meanwhile,the non-local hyperentanglement-assisted BSM has a success probability of 100%and is feasible with linear optical elements.Moreover,combined with the hyperentanglement heralded amplification and purification,our protocol is possible to realize long-distance one-step QD.

Effects of Electroplating Effluents on Growth, Heavy Metals Accumulation and Concentrations in Amaranthus viridis Lin.

Pollution in recent times has become prevalent due to industrial expansion,hence,releasing pollutants into the environ-ment.Thus,this study aimed at investigating the effects of effluents from electroplating companies on growth,heavy metals accumulation and concentrations in Amaranthus viridis.Seeds of A.viridis were obtained from the National Institute of Hor-ticulture,Ibadan.Loam soils were collected from Lagos State University and two samples of electroplating effluents were obtained from Oregun,Lagos.Seeds were sown,nursed,and transplanted in a uniform bucket filled with 5 kg loam soil and transplanted seedlings were treated with Effluent A(5 and 10%conc.)and Effluent B(5 and 10%conc.)and control respec-tively.Growth parameters such as plant height and so on were measured and plant samples harvested were analyzed for heavy metal concentrations using Atomic Absorption Spectrophotometer.Data collected were subjected to a one-way analysis of variance.Results revealed that Effluents A and B are highly acidic and above discharge limits.Also,the result revealed that 5%conc.of Effluents A and B had more effects on growth(p<0.05)of A.viridis across the harvests than 10%conc.in relation to control.This result showed that the effluent samples affect the growth rhythms of plants.Results further revealed vigorous–1–1 accumulation of the heavy metals:Zn(241.66µg kg±0.10 at third harvest in Effluent A:10%),Cu(68.25µg kg±0.23 at–1–1 first harvest in Effluent B:5%),Cr(500µg kg±0.90 in harvests at all concentrations.)and Ni(500µg kg±0.90 at third harvest in Effluent B:5%)and all these metals are far above the control and permissible limits of WHO/FAO recommenda-tions.From this study,it could be concluded that electroplating effluents had adverse effects on growth and increased metals’bioaccumulation in A.viridis.Therefore,the treatment of effluents to enhance an eco-friendly environment should be done.

Effect of the Retarder on Initial Hydration and Mechanical Properties of the"one-step"Alkaliactivated Composite Cementitious Materials

This paper studied the effects of different retarders on the performance of the"one-step"alkali-activated composite cementitious material(ACCM)which is composed of ground granulated blast slag(GGBS)and fly ash(FA),and analyzed its mechanical properties,hydration mechanism,and retardation mechanism.The effects of retarders on the hydration products,mechanical properties,and hydration kinetics of ACCM were investigated using XRD,SEM,FTIR,EDS,and thermoactive microcalorimetry.The results showed that Na_(2)B_(4)O_(7)·10H_(2)O(B)delayed the exotherm during the alkali activation process and could effectively delay the setting time of ACCM,but the mechanical properties were slightly decreased.The setting time of ACCM increased with the increase in SG content,but the mechanical properties of ACCM decreased with the increase in SG content.C1_(2)H_(22)O_(11)(CHO)could effectively delay the hydration reaction of ACCM and weakly enhanced the compressive strength.H_(3)PO_(4)(HP)at a concentration of 0.05 mol/L had a certain effect on ACCM retardation,but HP at a concentration of 0.07 and 0.09 mol/L had an effect of promoting the setting and hardening time of ACCM.

Three-dimensional visualization technology for guiding one-step percutaneous transhepatic cholangioscopic lithotripsy for the treatment of complex hepatolithiasis

BACKGROUND Biliary stone disease is a highly prevalent condition and a leading cause of hospitalization worldwide.Hepatolithiasis with associated strictures has high residual and recurrence rates after traditional multisession percutaneous transhepatic cholangioscopic lithotripsy(PTCSL).AIM To study one-step PTCSL using the percutaneous transhepatic one-step biliary fistulation(PTOBF)technique guided by three-dimensional(3D)visualization.METHODS This was a retrospective,single-center study analyzing,140 patients who,between October 2016 and October 2023,underwent one-step PTCSL for hepatolithiasis.The patients were divided into two groups:The 3D-PTOBF group and the PTOBF group.Stone clearance on choledochoscopy,complications,and long-term clearance and recurrence rates were assessed.RESULTS Age,total bilirubin,direct bilirubin,Child-Pugh class,and stone location were similar between the 2 groups,but there was a significant difference in bile duct strictures,with biliary strictures more common in the 3D-PTOBF group(P=0.001).The median follow-up time was 55.0(55.0,512.0)days.The immediate stone clearance ratio(88.6%vs 27.1%,P=0.000)and stricture resolution ratio(97.1%vs 78.6%,P=0.001)in the 3D-PTOBF group were significantly greater than those in the PTOBF group.Postoperative complication(8.6%vs 41.4%,P=0.000)and stone recurrence rates(7.1%vs 38.6%,P=0.000)were significantly lower in the 3D-PTOBF group.CONCLUSION Three-dimensional visualization helps make one-step PTCSL a safe,effective,and promising treatment for patients with complicated primary hepatolithiasis.The perioperative and long-term outcomes are satisfactory for patients with complicated primary hepatolithiasis.This minimally invasive method has the potential to be used as a substitute for hepatobiliary surgery.

Study of the reaction mechanism for preparing powdered activated coke with SO_(2)adsorption capability via one-step rapid activation method under flue gas atmosphere

In this study,the impact of different reaction times on the preparation of powdered activated carbon(PAC)using a one-step rapid activation method under flue gas atmosphere is investigated,and the underlying reaction mechanism is summarized.Results indicate that the reaction process of this method can be divided into three stages:stage I is the rapid release of volatiles and the rapid consumption of O_(2),primarily occurring within a reaction time range of 0-0.5 s;stage II is mainly the continuous release and diffusion of volatiles,which is the carbonization and activation coupling reaction stage,and the carbonization process is the main in this stage.This stage mainly occurs at the reaction time range of 0.5 -2.0 s when SL-coal is used as material,and that is 0.5-3.0 s when JJ-coal is used as material;stage III is mainly the activation stage,during which activated components diffuse to both the surface and interior of particles.This stage mainly involves the reaction stage of CO_(2)and H2O(g)activation,and it mainly occurs at the reaction time range of 2.0-4.0 s when SL-coal is used as material,and that is 3.0-4.0 s when JJ-coal is used as material.Besides,the main function of the first two stages is to provide more diffusion channels and contact surfaces/activation sites for the diffusion and activation of the activated components in the third stage.Mastering the reaction mechanism would serve as a crucial reference and foundation for designing the structure,size of the reactor,and optimal positioning of the activator nozzle in PAC preparation.

Cyanide-free silver electroplating process in thiosulfate bath and microstructure analysis of Ag coatings

Cyanide-free silver electroplating was conducted in thiosulfate baths containing AgNO3 and AgBr major salts, respectively. The effects of major salt content and current density on surface quality, deposition rate and microhardness of Ag coatings were investigated. The optimized electroplating parameters were established. The adhesion strength of Ag coating on Cu substrate was evaluated and the grain size of Ag coating was measured under optimized electroplating parameters. The optimized AgNO3 content is 40 g/L with current density of 0.25 A/dm2. The deposited bright, smooth, and well adhered Ag coating had nanocrystalline grains with mean size of 35 nm. The optimized AgBr content was 30 g/L with current density of 0.20 A/dm2. The resultant Ag coating had nanocrystalline grains with mean size of 55 nm. Compared with the bath containing AgBr main salt, the bath containing AgNO3 main salt had a wider current density range, and corresponding Ag coating had a higher microhardness and a smaller grain size.

Surface pretreatment of Mg alloys prior to Al electroplating in TMPAC-AlCl_3 ionic liquids

It is difficult to directly electroplate Al on Mg alloys. The effects of pretreatment parameters on the corrosion resistance of films obtained on AZ31 Mg alloy surface were studied by using potentiodynamic polarization curves, to produce a compact interfacial layer as zinc-immersion deposition. After the substrate was pretreated under optimized conditions, aluminum was electrodeposited on AZ31 from TMPAC-AlCl3 room temperature ionic liquids. The depositions were characterized by scanning electron microscope equipped with energy dispersion X-ray. The results show that the traditional pretreatment of Mg alloys was successfully used for the Al-electroplating process from TMPAC-AlCl3 ionic liquids. The entire procedure includes alkaline cleaning, chemical pickling, surface activation （400 mL/L HF acid, 10 min）, zinc-immersion （20 min） and anhydrous treatment. A relatively compact zinc-immersion film was prepared on the substrate surface. A silvery-colored satin aluminum deposition was obtained on AZ31 from TMPAC-AlCl3 using direct current plating.

Recovery of heavy metals from electroplating sludge and stainless steel pickle waste liquid by ammonia leaching method

A coordinative disposal process for treatment of electroplating sludge and stainless steel pickle waste liquid containing Cu, Ni, Zn, Cr and Fe etc., has been developed to recover valuable metals and to eliminate pollution. The recovery of Cu, Ni, Zn and Cr is 94%, 91%, 90% and 95%, respectively. The ammonia was recycled by the simplified process of CaO caustic distillation. The precipitated product of Cu, Ni and Zn obtained from caustic distillation of ammonia was separated by extraction or high\|pressure hydrogen reduction in an autoclave. The qualified metal salt products were obtained through extraction. The rich chromium residue from coordinative disposal was subjected to recover Cr by hydrothermal oxidation in NaOH medium and Fe\-3O\-4 was synthesized by wet methods from the residue produced by extracting Cr. Cr was a stable chemical fixed in Fe\-3O\-4 and harmless. The recovery process has been used in a pilot plant with sludge production capacity of 2000 t/a.

Electroless Nickel Plating and Electroplating on FBG Temperature Sensor

Metal-coated fiber Bragg grating（FBG）temperature sensors were prepared via electroless nickel（EN）plating and tin electroplating methods on the surface of normal bare FBG.The surface morphologies of the metal-coated layers were observed under a metallographic microscope.The effects of pretreatment sequence,pH value of EN plating solution and current density of electroplating on the performance of the metal-coated layers were analyzed.Meanwhile, the Bragg wavelength shift induced by temperature was monitored by an optical spectrum analyzer.Sensitivity of the metal-coated FBG（MFBG）sensor was almost two times that of normal bare FBG sensor.The measuring temperature of the MFBG sensor could be up to 280℃,which was much better than that of conventional FBG sensor.

Pulse electroplating of Ni-W-P coating and its anti-corrosion performance

Ni-W-P coatings were electrodeposited on copper substrates by pulse electroplating.Effects of electrolyte pH(1-3),temperature(40-80°C),average current density(1-7A/dm2)and pulse frequency(200-1000Hz)on deposition rate,structure and corrosion resistance performance of Ni-W-P coatings were studied by single factor method.Surface morphology,crystallographic structure and composition of Ni-W-P coatings were investigated by means of scanning electron microscopy,X-ray diffractometry and energy dispersive X-ray spectroscopy,respectively.Corrosion resistance performances of Ni-W-P coatings were studied by potentiodynamic polarization and electrochemical impedance spectroscopy in3.5%NaCl solution(mass fraction)and soil-containing solution.It was found that the pulse electroplated Ni-W-P coatings have superior corrosion resistance performance and the electroplating parameters significantly affect the structure and corrosion resistance performance of Ni-W-P coatings.The optimized parameters of pulse electroplating Ni-W-P coatings were as follows:pH2.0,temperature60°C,average current density4A/dm2,and pulse frequency600Hz.The Ni-W-P coating prepared under the optimized parameters has superior corrosion resistance(276.8kΩ)and compact surface without any noticeable defect.

Removal of copper ions from electroplating rinse water using electrodeionization

An improved configuration of the membrane stack was adopted in the electrodeionization （EDI） cell to prevent precipitation of bivalent metal hydroxide during the running. The operational parameters that influenced the removal of copper ions from the dilute solution were optimized. The result showed that a moderate decrease in the inlet pH value and a moderate increase in the applied voltage could achieve a better removal effect. The steady process of electroplating wastewater treatment could be achieved with a removal efficiency of more than 99.5% and an enrichment factor of 5-14. The concentration of copper in purified water was less than 0.23 mg/L. This demonstrated the applicability of recovering heavy metal ions and purified water from electroplating effluent for industrial reuse.

Improvement of stability of trivalent chromium electroplating of Ti based IrO_2+Ta_2O_5 coating anodes

The preparation process and properties of the thermally prepared Ti anodes coated with IrO2+Ta2O5 was studied. The structure and morphologies of the IrO2+Ta2O5 coatings were determined by XRD and SEM. Their electrochemical properties were studied by polarization curve and cyclic voltammetry. Trivalent chromium electroplating using Ti/IrO2+Ta2O5 anodes is carried out and the results were analyzed. Results show that this anode exhibits excellent electrochemical activity and stability in sulfate electrolysis. The electrocatalytic activity is determined not only by the content of IrO2 but also the structure and morphology of the anode coatings. The electroplating results indicats that Ti/IrO2+Ta2O5 anodes have excellent capabilities and merits in improving the stability of trivalent chromium electroplating in sulfate system.

Electroplating of Ni/Co–pumice multilayer nanocomposite coatings: Effect of current density on crystal texture transformations and corrosion behavior

The present paper aims to investigate the influence of the current density in the electroplating process on the microstructure, crystal texture transformations, and corrosion behavior of Ni/Co pumice multilayer nanocomposite coatings. The Ni/Co pumice composite coatings were prepared by deposition of Ni, followed by the simultaneous deposition of pumice nanoparticles (NPs) in a Co matrix via an electroplating process at various current densities. Afterward, the morphology, size, topography, and crystal texture of the obtained samples were investigated. Furthermore, electrochemical methods were used to investigate the corrosion behavior of the produced coatings in a solution of 3.5wt% NaCl. The results indicated that increasing the plating current density changed the mechanism of coating growth from the cell state to the column state, in- creased the coating thickness, roughness, and texture coefficient (TC) of the Co (203) plane, and reduced the amount of pumice NPs incorporated into the Ni/Co pumice composite. The electrochemical results also indicated that increasing the current density enhanced the corrosion resistance of the Ni/Co pumice composite.

Progress of electroplating and electroless plating on magnesium alloy

The current research processes of electroplating and electroless Ni-P alloy plating on magnesium alloys were reviewed. Theoretically,the reason for difficulties in electroplating and electroless plating on magnesium alloys was given.The zinc immersion, copper immersion,direct electroless Ni-P alloy plating and electroplating and electroless plating on magnesium alloys prepared by chemical conversion coating were presented in detail.Especially,the research development of magnesium alloy AZ91 and AZ31 was discussed briefly.Based on the analysis,the existing problems and future research directions were then given.

Stimulation of Rare Earths in Quartz Optical Fiber Surface Metallization by Electroless Plating and Electroplating

This research aims to use several kind of rare earth oxides, such as Nd2O3, Yb2O3, Ce2O3 and La2O3, to improve the electroless plating and electroplating processes for surface metallization of quartz optical fiber (silicon fiber) for its practical uses. The effects of the rare earth oxides on the deposition rate of Ni-P-B, the stability of the plating solution and the surface property of the film were investigated and the comparisons of their behaviours were made. The effects of rare earth oxide of La2O3 on the hardness and surface property of the Ni film prepared by electroplating process were studied. The surface morphonogies, compositions and hardness of the Ni-P-B and Ni films were characterized and analyzed by SEM, MSM, ICP and DIMHM, respectively. The experimental results showed that Ce2O3 with the concentration of 4 mg·L-1 was the best one among the four rare earth oxides with suitable concentrations in increasing the deposition rate, enhancing the stability of the electroless plating solution and improving the surface property of the Ni-P-B film. The improvements of the hardness and surface property of the Ni film prepared by electroplating with adding La2O3 were discovered. No obvious influences of Ce2O3 and La2O3 on the compositions of Ni-P-B and Ce free in the Ni-P-B film were found because of its much more nagative deposition potential than those of the used reducing agents in this experiment. The total diameter of the quartz optical fiber with deposited Ni-P-B film and Ni film was about 1.7 mm, which could be satisfactorily for the practical uses of quartz optical fiber in many fields.

Electrochemical characteristics of electroplating and impregnation Ni-P/SiC/PTFE composite coating on 316L stainless steel

Ni-P/SiC/PTFE coating was obtained on the surface of 316L stainless steel by electrodeposition of Ni-P/SiC coating and immersion of PTFE(polytetrafluoroethylene).The surface morphology and composition were analyzed by scanning electron microscope and energy dispersive spectrometer.The corrosion resistance of the coating in 0.5 mol/L H2SO4+2×10−6 HF solution was studied by electrochemical method.Surface contact angle was used to test the hydrophobic properties of the coating.The results indicated that the Ni-P/SiC/PTFE coating prepared on the surface of stainless steel was uniform and compact,which significantly improved the self-corrosion potential of stainless steel.The self-corrosion current density decreased from 7.62 to 0.008μA/cm2.The durability performance of coating was tested under 0.6 V voltage and the stable corrosion current density value was 0.19μA/cm2,then wetting angle was tested after durability experiment and the value is 134.5°.

Electroplating process of amorphous Fe-Ni-Cr alloy

A novel process of electroplating amorphous Fe Cr Ni alloy in chloride aqueous solution with Fe(Ⅱ), Ni(Ⅱ) and Cr(Ⅲ) was reported. Couple plasma atomic emission spectrometry (ICP AES), X ray diffractometry(XRD), scanning electronic microscopy(SEM), microhardness test and rapid heating cooling method were adopted to detect the properties of the amorphous Fe Ni Cr deposit, such as composition, crystalline structure, micrograph, hardness, and adherence between deposit and substrate. The effects of the operating parameters on the electrodeposit of the amorphous Fe Ni Cr alloy were discussed in detail. The results show that a 8.7?μm thick mirror like amorphous Fe Ni Cr alloy deposit, with Vicker’s hardness of 530 and composition of 45%～55% Fe, 33%～37% Ni, 9%～23% Cr was obtained by electroplating for 20?min at room temperature(10～30?℃), cathode current 10～16?A/dm 2, pH=1.0～3.0. The XRD patterns show that there only appears a broad hump around 2 θ of 41?°～47?°for the amorphous Fe Ni Cr alloy deposit, while the SEM micrographs show that the deposit contains only a few fine cracks but no pinholes.

Thermal spray coating on conductor rolls in electroplating line

In electroplating lines,many conductor rolls are installed in electroplating bath.Typical electroplatings are tin plating(ETL) and zinc plating(EGL),and from required product qualities,a vertical cell for the former and a horizontal cell for the latter is often used.Generally,chrome plating or WC cermet thermal spray coating is applied to stainless steel conductor roll in ETL for prolonging service life by improvement of wear resistance and corrosion resistance.On the other hand,Hastelloy type alloy substrate is used for conductor rolls in EGL due to severe corrosion environment of electro plating solution.Thermal spray coating is effective for reducing wear,but there are many cases where the coating cannot complete expected service life when corrosion becomes an issue.In this study,thermal spray coating for ETL conductor roll and development of the coating for EGL conductor roll to meet expected service life are described.

Influence of additives and concentration of WC nanoparticles on properties of WC−Cu composite prepared by electroplating

The effects of additives(polyethylene glycol(PEG),sodium dodecyl sulfate(SDS))and WC nano-powder on the microstructure,relative density,hardness and electrical conductivity of electroplated WC−Cu composite were investigated.The preparation mechanism was also studied.The microstructure of samples was analyzed by XRD,SEM,EDS,TEM and HRTEM.The synergistic effect of PEG and SDS made the WC−Cu composite more compact during the electroplating process.The hardness of WC−Cu composites increased with the increase in WC content,while the electrical conductivity decreased with the increase in WC content.The density of samples tended to increase initially and then decreased with increase in the additive content.When the electroplating solution contained 10 g/L WC nanopowder,0.2 g/L PEG and 0.1 g/L SDS,the WC−Cu composite exhibited hardness of HV 221 and electric conductivity of 53.7 MS/m.Therefore,the results suggest that WC−Cu composite with excellent properties can be obtained by optimizing the content of additives and WC particles.