One-step green method to prepare progressive burning gun propellant through gradient denitration strategy

Gradiently denitrated gun propellant(GDGP)prepared by a“gradient denitration”strategy is obviously superior in progressive burning performance to the traditional deterred gun propellant.Currently,the preparation of GDGP employed a tedious two-step method involving organic solvents,which hinders the large-scale preparation of GDGP.In this paper,GDGP was successfully prepared via a novelty and environmentally friendly one-step method.The obtained samples were characterized by FT-IR,Raman,SEM and XPS.The results showed that the content of nitrate groups gradiently increased from the surface to the core in the surface layer of GDGP and the surface layer of GDGP exhibited a higher compaction than that of raw gun propellant,with a well-preserved nitrocellulose structure.The denitration process enabled the propellant surface with regressive energy density and good progressive burning performance,as confirmed by oxygen bomb and closed bomb test.At the same time,the effects of different solvents on the component loss of propellant were compared.The result showed that water caused the least component loss.Finally,the stability of GDGP was confirmed by methyl-violet test.This work not only provided environmentally friendly,simple and economic preparation of GDGP,but also confirmed the stability of GDGP prepared by this method.

Noether＇s theorem and one-step corrections method for holonomic system

In this paper, a new computational method for improving the accuracy of numerically computed solutions is introduced. The computational method is based on the one-step method and conserved quantities of holonomic systems are considered as kinematical constraints in this method.

Constraint Stabilization and One-Step Correction Method for Dynamical Systems

A computational method of constraint stabilization and correction is introduced. The method is based on the Baumgart＇s one-step method. Constraint conditions are addressed to stabilize and correct the solution. Two examples are given to illustrate the results of the method.

A LOW-PRESSURE AND ONE-STEP METHOD FOR THE SYNTHESIS OF ALKYLIDYNETRICOBALT NONACARBONYL CLUSTERS:RCCo_8(CO)_9

Metal clusters RCCo_3(CO)_9(R-H,C1,Br,CH_3,Ph) were prepared in 18.8-57.3% yields from the reaction of cobalt(Ⅱ)salt and RCX_a under mild PTC conditions(latm CO,25℃).The cobalt salt was reduced to Co(CO)_4 in the presence of Na_3S_2O_4.

One-step Eco-friendly Fabrication of Antibacterial Polyester Via On-line Amination Reaction by Melt Coextrusion

The work is dedicated to develop a one-step eco-friendly method to prepare antibacterial polyethylene terephthalate(PET).We report a one-step eco-friendly method to manufacture antibacterial PET via on-line amination reaction by melt coextrusion.Beside evenly mixing of poly(hexamethylene guanidine)(PHMG)and PET in the melt coextrusion procedure,the amination reaction also occurred between PHMG and PET under high temperature(230-270℃).The antibacterial ability of composite PET showed obvious PHMG concentration dependence,and antibacterial activity reached more than 99%when PHMG content was 2.5 wt%.Moreover,LIVE/DEAD fluorescence test further confirmed that the composite PET could kill bacteria quickly and efiectively(within 30 min);while negligible cytotoxicity was observed to HSF and HUVEC cells.Onestep eco-friendly fabrication of composite antibacterial PET was accomplished by on-line melt coextrusion.The composite antibacterial PET has potential use in multiple fields to combat with pathogenic including textiles,packaging materials,decoration materials and biomedical devices,etc.

In-situ-selective-UV crosslinking fabrication of solid liquid host guest electrolyte: A facile one-step method realizing highly flexible electrochromic device

Flexible electrochromic devices (FECDs) are promising candidates for the next generation of wearable electronics due to their low operating voltage and energy consumption. For the flexible electrochromic devices, the electrolyte is an important component. Typically, the electrolyte needs to be formulated according to the device structure and usage scenario. A high-performance electrolyte involves consideration of many factors, including choosing the right polymer, solvent, curing agent, and ion type to satisfy particular device specifications. In this work, a ultraviolet-curable solid–liquid host–guest (UV-SLHG) electrolyte is developed. Several aspects of performance are improved by introducing the solid–liquid coexisting microstructure without changing the electrolyte formulation, including excellent adhesion, a 30% increase in tensile characteristics, and a seven-fold increase in ionic conductivity when compared to a fully cured solid-state electrolyte. More importantly, the unique advantage of SLHG electrolytes lies that the thickness will not change significantly during bending. The FECD made by using the UV-SLHG-based electrolyte sustained 10,000 bending cycles at the bending radius of 2.5 mm while maintaining outstanding optical modulation. A wearable ring-type ECD and a battery-free FECD wine label were made as demonstrators. The UV-SLHG strategy is not only suitable for the FECDs but also universally applicable to other electrolyte-based of flexible electronics such as flexible capacitors and batteries.

Synthesis of Codon-optimized Human Interleukin-18 Gene by Combination of Chemical and Enzymatic Method

According to the amino acid sequence and codon preference of E. coli, the human interleukin-18（IL-18） gene was optimized to avoid the rare codons. The total length of the synthesized gene is 571 bp; 18 oligonucleotides, DNA fragments were designed and synthesized by the phosphoramidite four-step chemical method. The whole DNA sequence was synthesized by a one-step total gene synthesis method, and then inserted in pUC18 vector. Five positive clones identified by blue-white colony screening were sent to Shanghai Sangon Biological Engineering Technology and Service Co., Ltd. for sequencing. The sequencing result shows that one clone contained the complete correct gene in all the five positive clones.

One-Step Multiplex PCR for Simultaneous Detection and Identification of Eight Medically Important <i>Candida</i>Species

Recently, the incidence of Candida infections has substantially increased. Conventional identification methods for Candida species are technically difficult to conduct and cannot accurately distinguish each species. The purpose of the present study was to design primers to identify and detect simultaneously eight medically important Candida species using one-step multiplex PCR. PCR primers were designed based on partial sequences of intergenic spacer (IGS) and internal transcribed spacer (ITS) genes of eight medically important Candida species. These primers were able to distinguish each Candida species and did not display cross-reactivity with representative Candida species other than the eight Candida species. Moreover, our developed one-step multiplex PCR method is accurate, specific, cost-effective, time-saving, and worked without requiring DNA extraction.

Simulation of bulk metal forming processes using one-step finite element approach based on deformation theory of plasticity

The bulk metal forming processes were simulated by using a one-step finite element(FE)approach based on deformation theory of plasticity,which enables rapid prediction of final workpiece configurations and stress/strain distributions.This approach was implemented to minimize the approximated plastic potential energy derived from the total plastic work and the equivalent external work in static equilibrium,for incompressibly rigid-plastic materials,by FE calculation based on the extremum work principle.The one-step forward simulations of compression and rolling processes were presented as examples,and the results were compared with those obtained by classical incremental FE simulation to verify the feasibility and validity of the proposed method.

Physiochemical and Biological Properties of Modified Collagen Sponge from Porcine Skin

The aim of the present study was to compare one-step method to EDC/NHS crosslinking （EDC/NHS group） and one-step simultaneous method to EDC/NHS crosslinking and heparin immobilization （EDC/NHS- Heparin group） in improving physiochemical and biological properties of native collagen sponge （Control group）. Modified collagen sponge overcome the disadvantages of native collagen sponge. IR spectra suggest the change of the functional groups. DSC data indicate that the stability of caloric transformation in EDC/NHS group is slightly higher than that of EDC/NHS-Heparin group. The crosslinking degree, stability against enzymes, stability in morphologically and biomechanical properties of EDC/NHS-Heparin group are higher than those of EDC/NHS group, whereas, the water-binding capacity in EDC/NHS-Heparin group is lower than that of EDC/NHS group. HUVECs in EDC/NHS-Heparin group scaffold proliferate fast, migrate well and distribute uniformly. One-step simultaneous method gains the better effects in above aspects, heparinized collagen matrices increase in angiogenic potential and suit for defect repairing and tissue engineering.

High CO methanation activity on zirconia-supported molybdenum sulfide catalyst

In this study, different methods were used to prepare MoO3/ZrO2 catalysts for sulfur resistant methanation reaction. It was found that MoO3/ZrO2 catalyst prepared by one-step co-precipitation method achieved high methanation performance. CO conversion could reach up to 90% on 25 wt% MoO3/ZrO2 catalyst, much higher than that on the conventional 25 wt% MoO3/Al2O3 catalyst. The Mo-based catalysts were characterized by XRF, XRD, Raman, BET, TEM and H2-TPR etc. It was found that MoO3 particles were highly dispersed on ZrO2 support for 25 wt% MoO3/ZrO2 catalyst prepared at 65-85℃ because of its relatively larger pore size, which contributed to a high CO conversion. Meanwhile, when MoO3 loading exceeded the monolayer coverage, the formed crystalline MoO3 and ZrM020g might block the micropores of the catalyst and make the methanation activity declined. These results are useful for preparing highly efficient catalyst for CO methanation process.

EFFICIENT ESTIMATION OF FUNCTIONAL-COEFFICIENT REGRESSION MODELS WITH DIFFERENT SMOOTHING VARIABLES

In this article,a procedure for estimating the coefficient functions on the functional-coefficient regression models with different smoothing variables in different coefficient functions is defined.First step,by the local linear technique and the averaged method,the initial estimates of the coefficient functions are given.Second step,based on the initial estimates,the efficient estimates of the coefficient functions are proposed by a one-step back-fitting procedure.The efficient estimators share the same asymptotic normalities as the local linear estimators for the functional-coefficient models with a single smoothing variable in different functions.Two simulated examples show that the procedure is effective.

One-step quadratic convergence of noninterior continuation method for NCP

A noninterior continuation method is presented, with only the certering step used at each iteration, for nonlinear complementarity problem. It is shown that the algorithm is globally linearly and locally quadratically convergent under certain conditions.

A one-step method for producing microencapsulated phase change materials

This short communication reports our recent work on the synthesis and characterisation ofmicrocapsules of phase change materials using silica as the shell material through a one-step method. The method uses no surfactants or dispersants for stabilising the capsules. The results show that the one-step method allows the tuning of the size and polydispersity of the capsules, and the use of different core materials. Analyses of the capsules show that they contain about 65% phase change materials. The results also suggest no need for a stabilising agent due to self-stabilisation by the amine groups. Further work is underway to investigate the mechanical and thermal properties of the microcapsules and the scale-up of the method.

PbI_(2)/Pb_(5)S_(2)I_(6)van der Waals Heterojunction Photodetector

Investigations of two-dimensional(2D)/one-dimensional(1D)van der Waals(vdW)heterojunctions have attracted significant attention due to their excellent properties such as the smooth heterointerface,the highly gate-tunable bandgap,and the ultrafast carrier transport.However,the complicated method of manufacturing vdW heterojunction represents a major problem that severely limits their practical applications.Herein,we develop one-step hydrothermal method and use it to synthesize 2D PbI_(2)/1D Pb_(5)S_(2)I_(6)vdW heterojunction.The PbI_(2)/Pb_(5)S_(2)I_(6)vdW heterojunction photodetector(PD)displays lower dark current(<20 pA),higher responsivity(up to 134 mA·W-1),self-powered and wider response spectrum in comparison with that of pristine PbI_(2)PD and Pb_(5)S_(2)I_(6)PD.This one-step hydrothermal method provides a new idea for preparing other mixed-dimensional heterojunction.

AN EFFECTIVE SEQUENTIAL QUADRATIC PROGRAMMING ALGORITHM FOR NONLINEAR OPTIMIZATION PROBLEMS

In this paper, a new globally convergent algorithm for nonlinear optimization problems with equality and inequality constraints is presented. The new algorithm is of SQP type which determines a search direction by solving a quadratic programming subproblem per iteration. Some revisions on the quadratic programming subproblem have been made in such a way that the associated constraint region is nonempty for each point x generated by the algorithm, i.e. , the subproblems always have optimal solutions. The new algorithm has two important properties. The computation of revision parameter for guaranteeing the consistency of quadratic subproblem and the computation of the second order correction step for superlinear convergence use the same inverse of a matrix per iteration, so the computation amount of the new algorithm will not be increased much more than other SQP type algorithms; Another is that the new algorithm can give automatically a feasible point as a starting point for the quadratic subproblems per iteration, this will obivously simplify the computation procedure of the subproblems. Some numerical results are reported.

Large-area gold nanohole arrays fabricated by one-step method for surface plasmon resonance biochemical sensing

Surface plasmon resonance(SPR) nanosensors based on metallic nanohole arrays have been widely reported to detect binding interactions in biological specimens. A simple and effective method for constructing nanoscale arrays is essential for the development of SPR nanosensors. In this work, we report a one-step method to fabricate nanohole arrays by thermal nanoimprinting in the matrix of IPS(Intermediate Polymer Stamp). No additional etching process or supporting substrate is required. The preparation process is simple, time-saving and compatible for roll-to-roll process, potentially allowing mass production. Moreover, the nanohole arrays were integrated into detection platform as SPR sensors to investigate different types of biological binding interactions. The results demonstrate that our one-step method can be used to efficiently fabricate large-area and uniform nanohole arrays for biochemical sensing.

Explicit High Order One-Step Methods for Decoupled Forward Backward Stochastic Differential Equations

By using the Feynman-Kac formula and combining with Itˆo-Taylor expansion and finite difference approximation,we first develop an explicit third order onestep method for solving decoupled forward backward stochastic differential equations.Then based on the third order one,an explicit fourth order method is further proposed.Several numerical tests are also presented to illustrate the stability and high order accuracy of the proposed methods.

A Class of Multiderivative Hybrid One-step Methods

This paper presents a class of hybrid one-step methods that are obtained by using Cramer's rule and rational approximations to function exp(q). The algorithms fall into the catalogue of implicit formula, which involves sth order derivative and s+1 free parameters. The order of the algorithms satisfies s+1≤p≤2s+2. The stability of the methods is also studied, necessary and sufficient conditions for A-stability and L-stability are given. In addition, some examples are also given to demonstrate the method presented.

Effect of sulfur source on photocatalytic degradation performance of CdS/MoS2 prepared with one-step hydrothermal synthesis

Cd S/Mo S2,an extremely efficient photocatalyst,has been extensively used in hydrogen photoproduction and pollutant degradation.Cd S/Mo S2can be synthesized by a facile one-step hydrothermal process.However,the effect of the sulfur source on the synthesis of Cd S/Mo S2via one-step hydrothermal methods has seldom been investigated.We report herein a series of one-step hydrothermal preparations of Cd S/Mo S2using three different sulfur sources：thioacetamide,L-cysteine,and thiourea.The results revealed that the sulfur source strongly affected the crystallization,morphology,elemental composition and ultraviolet（UV）–visible-light-absorption ability of the Cd S/Mo S2.Among the investigated sulfur sources,thioacetamide provided the highest visible-light absorption ability for Cd S/Mo S2,with the smallest average particle size and largest surface area,resulting in the highest efficiency in Methylene Blue（MB）degradation.The photocatalytic activity of Cd S/Mo S2synthesized from the three sulfur sources can be arranged in the following order：thioacetamideL-cysteinethiourea.The reaction rate constants（k）for thioacetamide,L-cysteine,and thiourea were estimated to be 0.0197,0.0140,and 0.0084 min^（-1）,respectively.However,thioacetamide may be limited in practical application in terms of its price and toxicity,while L-cysteine is relatively economical,less toxic and exhibited good photocatalytic degradation performance toward MB.