Effect of titanium on the sticking of pellets based on hydrogen metallurgy shaft furnace:Behavior analysis and mechanism evolution

Direct reduction based on hydrogen metallurgical gas-based shaft furnace is a promising technology for the efficient and low-carbon smelting of vanadium-titanium magnetite.However,in this process,the sticking of pellets occurs due to the aggregation of metal-lic iron between the contact surfaces of adjacent pellets and has a serious negative effect on the continuous operation.This paper presents a detailed experimental study of the effect of TiO2 on the sticking behavior of pellets during direct reduction under different conditions.Results showed that the sticking index(SI)decreased linearly with the increasing TiO2 addition.This phenomenon can be attributed to the increase in unreduced FeTiO3 during reduction,leading to a decrease in the number and strength of metallic iron interconnections at the sticking interface.When the TiO2 addition amount was raised from 0 to 15wt%at 1100°C,the SI also increased from 0.71%to 59.91%.The connection of the slag phase could be attributed to the sticking at a low reduction temperature,corresponding to the low sticking strength.Moreover,the interconnection of metallic iron became the dominant factor,and the SI increased sharply with the increase in re-duction temperature.TiO2 had a greater effect on SI at a high reduction temperature than at a low reduction temperature.

A novel one-time-programmable memory unit based on Schottky-type p-GaN diode

In this work,a novel one-time-programmable memory unit based on a Schottky-type p-GaN diode is proposed.During the programming process,the junction switches from a high-resistance state to a low-resistance state through Schottky junction breakdown,and the state is permanently preserved.The memory unit features a current ratio of more than 10^(3),a read voltage window of 6 V,a programming time of less than 10^(−4)s,a stability of more than 108 read cycles,and a lifetime of far more than 10 years.Besides,the fabrication of the device is fully compatible with commercial Si-based GaN process platforms,which is of great significance for the realization of low-cost read-only memory in all-GaN integration.

Evaluation of the Effectiveness and Safety of One-Time Endodontics in the Treatment of Chronic Apical Periodontitis with Sinus Tract in Pediatric Deciduous Teeth

Objective:To observe the effectiveness and safety of one-time endodontics in the treatment of chronic apical periodontitis with sinus tract in pediatric deciduous teeth.Methods:109 cases of children with chronic apical periodontitis with sinus tract in the deciduous teeth treated in our hospital from January 2022 to December 2023 were selected and grouped by the randomized numerical table method,with 54 cases in the experimental group and 55 cases in the control group.The experimental group was treated with one-time endodontics and the control group was treated with conventional endodontics.Results:After the treatment,the total effective rate of treatment was higher in the experimental group than in the control group(P<0.05);the incidence of adverse events was lower in the experimental group than in the control group(P<0.05);the satisfaction of the children's family members was higher in the experimental group than in the control group(P<0.05);the pain duration was lower in the experimental group than in the control group(P<0.05).Conclusion:In the experimental group,children with chronic apical periodontitis with sinus tract of the deciduous teeth were given one-time endodontic treatment,and the results of its implementation were relatively good.

An Artificial Intelligence Algorithm for the Real-Time Early Detection of Sticking Phenomena in Horizontal Shale Gas Wells

Sticking is the most serious cause of failure in complex drilling operations.In the present work a novel“early warning”method based on an artificial intelligence algorithm is proposed to overcome some of the known pro-blems associated with existing sticking-identification technologies.The method is tested against a practical case study(Southern Sichuan shale gas drilling operations).It is shown that the twelve sets of sticking fault diagnostic results obtained from a simulation are all consistent with the actual downhole state;furthermore,the results from four groups of verification samples are also consistent with the actual downhole state.This shows that the pro-posed training-based model can effectively be applied to practical situations.

Assessment of Knowledge, Attitude and Practices among Healthcare Workers in a Tertiary Care Hospital on Needle Stick Injury

Purpose: Needle-stick injury (NSI) is one of the most potential occupational hazards for healthcare workers because of the transmission of blood-borne pathogens. As per recent data, around 30 lakh healthcare workers sustain Needle stick injuries each year. This study was conducted to assess healthcare workers’ knowledge, attitude and practices regarding needle stick injury. Materials & Methods: A cross-sectional study was conducted in a Tertiary Care Hospital over the period of 3 months. The study population consisted of Intern Doctors, Post Graduate resident Doctors, Staff Nurses, laboratory technicians of Government Medical College and New Civil Hospital, Surat (n = 300). The data were collected using a self-administered questionnaire via the means of Google Forms. Questionnaire was made with prior review literature. The data obtained were entered and analysed in Microsoft Excel. Results: The prevalence of NSI in our study was 46%, with a higher prevalence among the PG residents (72%). Overall scores regarding knowledge and attitude were better in PG residents (knowledge score > 7 in 71% and Attitude Score > 7 in 68% of PG Residents). Even though the PG residents scored highest in the knowledge category, the majority of them suffered needle stick injuries as a result of poor practice scores. Among those who had NSI (n = 139/300), 70% of study participants had superficial injuries, only 9% reported the incident, 18% got medical attention within 2 hours of the incident, and 7% followed up to recheck their viral markers status. Most incidents of NSI were due to hypodermic needles while recapping needles. Conclusion: Exposure to needle stick injuries and their underreporting remains a common problem. It is imperative that healthcare workers receive regular training on the proper handling of sharp objects. We can also draw the conclusion that preventing NSIs requires putting knowledge into practice.

Effect of Mouth Opening Training Stick Combined with Oral Massage on Mouth Opening Difficulty in Head and Neck Cancer Patients after Treatment

Objective: To study the application effect of mouth-opening training sticks combined with oral massage on patients with mouth-opening difficulty after treatment for head and neck cancer. Methods: Using convenient sampling, 60 patients with mouth-opening difficulty after treatment for head and neck cancer admitted to the Oncology Department from February 2022 to October 2023 were selected for a 2-week exercise and nursing program. The patients were divided into a control group (February 1, 2022 to November 30, 2022) and an observation group (December 1, 2022 to October 31, 2023), with 30 patients in each group. The control group underwent routine mouth-opening functional exercises combined with cork for oral support training, while the observation group underwent routine mouth-opening functional exercises combined with oral massage and mouth-opening training sticks for oral support training. The mouth-opening degree, mouth-opening difficulty level, comfort level, compliance, and quality of life were observed in both groups. Results: Before the intervention, there were no statistically significant differences in mouth-opening degree and mouth-opening difficulty level between the two groups (P > 0.05). After the intervention, the mouth-opening degree, mouth-opening difficulty level, oral comfort level, compliance, and QLICP-HN scores in the observation group were all better than those in the control group, with statistically significant differences (P < 0.05). Conclusion: The combination of mouth-opening training sticks and oral massage with mouth-opening functional exercises can effectively improve the degree of mouth-opening difficulty, enhance oral comfort, increase compliance with mouth-opening exercises, and improve quality of life.

Effects of Plant Spacing and Finger Sticking Area Settings for Machine Transplanting on Yield of Double-season Early Rice

The effects of rice transplanters＇ transplanting settings（plant spacing and finger sticking area） on rice yield were investigated in two early-season rice cultivars：hybrid rice cultivar（Zhuliangyou 819） and conventional rice cultivar（Zhongjiazao 17）.The results showed that,different transplanting settings resulted in different numbers of transplanted basic seedlings,and the rice yield was significantly correlated with the number of transplanted basic seedlings.The number of transplanted basic seedlings increased with the decrease of plant spacing and the increase of finger sticking area.The rate of lost hills of machine transplanting decreased with the increase of finger sticking area.The leaf area index and amount of dry matter accumulation were highly correlated with the number of transplanted basic seedlings.The average yield of the rice transplanted with a plant spacing of11.5 cm was higher than that with a plant spacing of 13.8 cm.In the field transplanted with the rice under the plant spacing of 13.8 cm,the rice yield increased with the increase of finger sticking area,and the finger sticking area of 2.23 cm2 showed the highest rice yield of 8 174.16 kg/hm2 of Zhuliangyou 819 and 7 925.54kg/hm2 of Zhongjiaozao17.In the field transplanted with the rice under the plant spacing of 11.5 cm,the rice yield was the highest with the finger sticking area of 1.83 cm2,and then decreased with the large finger sticking area.Under the plant spacing of 11.5 cm,the highest rice yields of Zhuliangyou 819 and Zhongjiaozao17 were 8 492.94 kg/hm2 and 8 000.23 kg/hm2,respectively.Therefore,the preferred machine transplanting settings for double-season early rice are a plant spacing of11.5 cm and a finger sticking area of 1.83 cm2,while the finger sticking area should be increased to 2.23 cm2 for conventional rice cultivars.

APPLICATION OF 2-D MOIRE INTERFEROMETRYOF STICKING FILM IN HUMAN TIBIA MEASUREMENT

This paper makes use of the method of testing and measuring the human body tibia by using2-D moire interferometry of sticking film. hased on the J'--y direction moire patterns recorded synchronously by 2-D optical path,the elastic constant,strain and displacement of the tibia are measured.Compared with the electric measuring method the error is samll and the sensitivity is high.

One-time fertilization at first flowering improves lint yield and dry matter partitioning in late planted short-season cotton

Cotton producers have substantially reduced their inputs(labor,nutrients,and management)mainly by adopting a shortseason cropping management that is characterized by late sowing,high density,and reduced fertilization with one-time application at the first bloom stage without lint yield reduction.However,it has been hypothesized that one-time fertilization at an earlier growth stage could be a more effective and economic management practice.A two-year field experiment was conducted by applying five fertilizer one-time fertilization at 0(FT1),5(FT2),10(FT3),15(FT4),and 20(FT5)days after the first flower appeared in the field and one three-split fertilizer application taken as the conventional control(FT6),making six treatments altogether.Cotton growth period,biomass accumulation,yield,and its formation were quantified.The results showed that the one-time fertilization did not affect the cotton growth progress as compared to FT6,however,the total crop cycles for FT3–FT5 were 3 days shorter.FT1 produced the highest cotton lint yield(1396 kg ha–1),which was similar to the FT6 but higher than the other treatments,and could be attributed to more bolls per unit area and higher lint percentage.Cotton yield was positively correlated with cotton plant biomass accumulated.FT1 had both the highest average(VT)(193.7 kg ha–1 d–1)and the highest maximum(VM)(220.9 kg ha–1 d–1)rates during the fast biomass accumulation period.These results suggest that one-time fertilizer application at the first flower stage might be an adjustment that is more effective than at first bloom,and allowed for easier decision making for application date due to non counting of plants with flowers is needed.

Test research on sticking mechanism during hot rolling of SUS 430 ferritic stainless steel

The sticking phenomenon during hot rolling of SUS 430 ferritic stainless steel was investigated by means of a two-disc type high-temperature wear tester. The test results indicate that sticking particles on the surfaces of high chromium steel （HiCr） and high-speed steel （HSS） rolls undergo nucleation, growth, and saturation stages. Grooves on the roll surface generated by grinding provide nucleation sites for sticking particles. The number of sticking particles on the HiCr roll surface is greater than that on the HSS roll surface. The average surface roughnesses （Ra） of HiCr and HSS rolls change from 0.502 and 0.493 μm at the initial stage to 0.837 and 0.530 μm at the saturation stage, respectively. The test further proves that the sticking behavior is strongly dependent on roll materials, and the HSS roll is more benefi- cial to prevent particles sticking compared with the HiCr roll under the same hot-rolling conditions.

One-time sintering process to modify xLi2MnO3(1-x)LiMO2 hollow architecture and studying their enhanced electrochemical performances

To solve the critical problems of lithium rich cathode materials, e.g., structure instability and short cycle life, we have successfully prepared a ZrO2-coated and Zr-doping xLi2MnO3·(1–x)LiMO2 hollow architecture via one-time sintering process. The modified structural materials as lithium-ion cathodes present good structural stability and superior cycle performance in LIBs. The discharge capacity of the ZrO2-coated and Zr-doped hollow pristine is 220 mAh g-1 at the 20th cycle at 0.2 C(discharge capacity loss, 2.7%)and 150 m Ah g-1 at the 100 th cycle at 1 C(discharge capacity loss, 17.7%), respectively. However, hollow pristine electrode only delivers 203 m Ah g-1 at the 20 th cycle at 0.2 C and 124 mAh g-1 at the 100 th cycle at 1 C, respectively, and the corresponding to capacity retention is 92.2% and 72.8%, respectively.Diffusion coefficients of modified hollow pristine electrode are much higher than that of hollow pristine electrode after 100 cycles(approach to 1.4 times). In addition, we simulate the adsorption reaction of HF on the surface of ZrO2-coated layer by the first-principles theory. The calculations prove that the adsorption energy of HF on the surface of ZrO2-coated layer is about-1.699 e V, and the ZrO2-coated layer could protect the hollow spherical xLi2MnO3·(1–x)LiMO2 from erosion by HF. Our results would be applicable for systematic amelioration of high-performance lithium rich material for anode with the respect of practical application.

Sticking of iron ore pellets in direct reduction with hydrogen and carbon monoxide:Behavior and prevention

A series of reduction experiments of iron ore pellets with hydrogen,carbon monoxide and their mixture were carried out in a laboratory scale shaft furnace.The sticking behavior accompanying reduction of iron ore pellets was investigated.And morphology of the sticking interface forming during reduction was analyzed by SEM equipped with EDS.In order to evaluate the effects of the temperature and gas composition on sticking properties,reduction of iron ore pellets were conducted at 800-1000 ℃.The results show that the sticking strength of the pellets increases with temperature,however,decreases with hydrogen content in reducing gas.For an efficient shaft furnace operation in direct reduction(DR),relative prevention of sticking such as coating of pellets was also developed to solve sticking problem.The results show that CaO is a suitable material for the coating method.

Cryptanalysis of the One-Time Proxy Signature Scheme Used in Mobile Agents

We ayptanalyze Kim et. al's one-time proxy signature scheme used in mobileagents, and then a successful forgery is introduced It is showed that a dishonest customer cansuccessfully forge a valid one-time proxy signature by impersonating the stiver Furthermore, he canrequest the server with responsibility for the forged bidding information.

A New Method for Predicting Wall Sticking Occurrence Temperature of High Water Cut Crude Oil

In crude oil transportation, adhesion of oil on pipe wall can cause partial or total blockage of the pipe. This process is significantly affected by wall sticking occurrence temperature(WSOT). In this work, an efficient approach for estimating WSOT of high water-cut oil, which can agree well with the actual environment of multiphase transportation pipeline, is proposed. Based on the energy dissipation theory, it is possible to make comparison of average shear rates between the stirred vessel and the flow loop. The impacts of water content and shear rate on WSOT are investigated using the stirred vessel and the flow loop. Good agreement has been observed between the stirred vessel and the flow loop results with the maximum and the average absolute deviations equating to 3.30 °C and 2.18 °C, respectively. The development of gathering scheme can enjoy some benefits from this method.

Design of 32 kbit one-time programmable memory for microcontroller units

A 32 kbit OTP(one-time programmable)memory for MCUs(micro-controller units)used in remote controllers was designed.This OTP memory is used for program and data storage.It is required to apply 5.5V to BL(bit-line)and 11V to WL(word-line)for a OTP cell of 0.35μm ETOX(EEPROM tunnel oxide)type by MagnaChip.We use 5V transistors on column data paths to reduce the area of column data paths since they require small areas.In addition,we secure device reliability by using HV(high-voltage)transistors in the WL driver.Furthermore,we change from a static logic to a dynamic logic used for the WL driver in the core circuit.Also,we optimize the WD(write data)switch circuit.Thus,we can implement them with a small-area design.In addition,we implement the address predecoder with a small-area logic circuit.The area of the designed 32 kbit OTP with 5V and HV devices is 674.725μm×258.75μm(=0.1745mm2)and is 56.3% smaller than that using 3.3V devices.

Wall Sticking of High Water-Cut, Highly Viscous and High Gel-Point Crude Oil Transported at Low Temperatures

Some crude oils with high water cut have the capability to flow below the oil gel point, while the oil particles adhere to the pipe wall in the form of paste, also called "wall sticking". Wall sticking is a serious problem during the pipeline transportation, leading to partial or total blockage of the pipeline and energy wastage. In this paper, a series of laboratory flow loop experiments were conducted to observe the wall sticking characteristics of crude oil with high water cut, high viscosity and high gel point at low transportation temperatures. The effects of shear stress and water cut on the wall sticking rate and occurrence temperature were investigated. Experimental results indicated that the wall sticking rate and occurrence temperature were lower under stronger shear stress and higher water cut conditions. A criterion of wall sticking occurrence temperature(WSOT) and a regression model of wall sticking rate were then established. Finally, the software was developed to calculate the pressure drop along the pipelines of crude oils with high water-cut. It was able to predict the wall sticking thickness of gelled oil and then calculate the pressure drop along the pipelines. A typical case study indicated that the prediction results obtained from the software were in agreement with actual measured values.

闭合复位内固定联合joy stick操纵杆技术治疗儿童难复性肱骨髁上骨折效果观察

目的观察闭合复位内固定联合joy stick操纵杆技术治疗儿童难复性肱骨髁上骨折的临床效果。方法选择因“肘关节外伤后肿痛伴活动受限”入院患儿4例,均诊断为GartlandⅢ型肱骨髁上骨折,均采用闭合复位内固定联合joy stick操纵杆技术治疗。结果4例患儿均获得满意复位,无一例转为切开复位,平均手术时间66 min,住院时间均<5 d。出院后规律复查换药,1月后均恢复良好,骨折线对位满意,未出现感染等短期并发症,拔除克氏针。结论Joy stick操纵杆技术不仅可以更加准确地控制肱骨轴的旋转,还能更快地获得复位和维持复位,进针顺利,手术时间短,减少转为切开复位,降低手术难度,且未增加围手术期并发症。

One-time Shaping Technological System of Lightweight Roof Greening

Lightweight roof greening is an important way for improving urban ecological environment and has good ecological and social benefits, but the investment is- too-high for the investors. Therefore, it is necessary to improve the system of lightweight roof greening. This study introduced a lightweight roof greening mode with low cost, simple construction, rapid formation, good economic benefit and convenient curing.

Influence of Oil and Water Components on Wall-sticking Occurrence Temperature in High Water-cut Crude Oil Pipeline

To study the wall-sticking phenomenon and prevent pipeline blockage accidents,two analytical methods are used to evaluate the influence of different crude oil components on the wall-sticking occurrence temperature(WSOT).The WSOT and the interactions among oil,water,and surface solids are measured and calculated by various devices under different values of the wax content,water pH,and salinity.The results show that there is greater correlation between the wax content and WSOT than between resins/asphaltenes and WSOT.Furthermore,the wax content,water pH,and salinity have different effects on WSOT.There is generally a positive correlation between wax content and WSOT,whereas the maximum WSOT occurs when the water pH is in the range 5.7–6.5,and decreases under more acidic or alkaline conditions.As the salinity increases,WSOT decreases slightly,but quickly becomes saturated.In terms of interactions,variations in the interfacial tension and adhesion work with pH and salinity are consistent with that of WSOT,while the contact angle exhibits the opposite relation.

Operational procedures of auricular point sticking technology

As an external treatment technique of traditional Chinese medicine(TCM),auricular point sticking,which is rooted in holographic biology theory and TCM viscera and meridian theory,is a safe and effective treatment method.This article introduces the technology overview and development process.The auricular point sticking technique for constipation is taken as an example to specify the basic requirements,assessment,operational points,acupoint selection and matters needing attention during the implementation of the auricular acupressure technique,providing a reference for the operating procedures of this technique in the clinical treatment of other diseases such as insomnia,diarrhea,colds,hypertension,headache,and dysmenorrhea.