期刊文献+
共找到1,944篇文章
< 1 2 98 >
每页显示 20 50 100
Corrosion Inhibition by Co-Immobilized Lysozyme and Lipase in Circulating Cooling Water System 被引量:3
1
作者 Liu Fang Lü Yucui +3 位作者 Jiang Guofei Chen Xiaorui Sun Juan Zhao Chaocheng 《China Petroleum Processing & Petrochemical Technology》 SCIE CAS 2017年第2期21-32,共12页
The corrosion inhibition performance of co-immobilized lysozyme and lipase was investigated in a recirculating cooling water system. Four methods were carried out in co-immobilization, and the operating parameters wer... The corrosion inhibition performance of co-immobilized lysozyme and lipase was investigated in a recirculating cooling water system. Four methods were carried out in co-immobilization, and the operating parameters were optimized by using the respond surface methodology(RSM). The corrosion inhibition performance of co-immobilized lipase and lysozyme was evaluated by weight loss measurements and electrochemical measurements. The results revealed that the optimal co-immobilization method should be the sequential immobilization of lysozyme and then lipase. The inhibition efficiency was 86.10% under the optimal co-immobilized conditions. Electrochemical data showed that co-immobilized lysozyme and lipase was a mixed-type inhibitor and the corrosion inhibition efficiency was 81%. 展开更多
关键词 circulating cooling water CO-IMMOBILIZATION LYSOZYME LIPASE corrosion inhibition
下载PDF
Optimization of circulating cooling water systems based on chance constrained programming 被引量:2
2
作者 Bo Liu Yufei Wang Xiao Feng 《Chinese Journal of Chemical Engineering》 SCIE EI CAS CSCD 2021年第12期167-178,共12页
Recent research on deterministic methods for circulating cooling water systems optimization has been well developed. However, the actual operating conditions of the system are mostly variable, so the system obtained u... Recent research on deterministic methods for circulating cooling water systems optimization has been well developed. However, the actual operating conditions of the system are mostly variable, so the system obtained under deterministic conditions may not be stable and economical. This paper studies the optimization of circulating cooling water systems under uncertain circumstance. To improve the reliability of the system and reduce the water and energy consumption, the influence of different uncertain parameters is taken into consideration. The chance constrained programming method is used to build a model under uncertain conditions, where the confidence level indicates the degree of constraint violation. Probability distribution functions are used to describe the form of uncertain parameters. The objective is to minimize the total cost and obtain the optimal cooling network configuration simultaneously.An algorithm based on Monte Carlo method is proposed, and GAMS software is used to solve the mixed integer nonlinear programming model. A case is optimized to verify the validity of the model. Compared with the deterministic optimization method, the results show that when considering the different types of uncertain parameters, a system with better economy and reliability can be obtained(total cost can be reduced at least 2%). 展开更多
关键词 circulating cooling water system UNCERTAINTY Chance constrained programming DESIGN OPTIMIZATION SIMULATION
下载PDF
MIC in Circulating Cooling Water System 被引量:1
3
作者 Ping Xu Zhaoyi Xu +2 位作者 Jin Wang Yajun Zhang Li Zhang 《Journal of Water Resource and Protection》 2012年第4期203-206,共4页
MIC is one of the main problems of circulating cooling water system. The direct economic loss by MIC is about 300 to 500 billion dollars. It is good to understand MIC in order to control MIC. Source and species of mic... MIC is one of the main problems of circulating cooling water system. The direct economic loss by MIC is about 300 to 500 billion dollars. It is good to understand MIC in order to control MIC. Source and species of microorganisms was introduced firstly. There are three kinds of microorganisms in the system, including bacteria, fungi and algae. Species of these microorganisms are shown in the paper. Then, mechanisms of MIC are analysed. Although there is no universal mechanism of MIC, MIC is still mainly an electrochemical corrosion in nature. Meanwhile, the mechanisms on SRB and iron bacteria are introduced in details. At last, several methods of microorganisms control are put forward in the paper. 展开更多
关键词 circulating cooling water System MIC MICROORGANISMS SPECIES MECHANISM Of MIC Control Methods
下载PDF
Ion Exchange Softening and Alkalization Treatment for Zerodischarge of Circulating Cooling Water 被引量:1
4
作者 Huiming Zeng Jiuyang Lin +3 位作者 Chunsong Ye Lihui Tong Xiaolan Chen Fei Yu 《Journal of Electromagnetic Analysis and Applications》 2009年第1期6-10,共5页
In order to solve the problems including pipe corrosion, scaling and microbial growth, which severely threat safe op-eration of circulating cooling water system, this paper proposes ion exchange softening and alkaliza... In order to solve the problems including pipe corrosion, scaling and microbial growth, which severely threat safe op-eration of circulating cooling water system, this paper proposes ion exchange softening and alkalization process to solve these problems and carries out a series of studies to study the feasibility of ion exchange softening and alkaliza-tion process in the simulation process of circulating cooling water system. The studies include product water quality of ion exchange softening and alkalization process, effect on the performance of carbon steel and brass, and the inhibition that suppresses microbial growth. The results indicate that ion exchange softening and alkalization process is feasible to prevent the circulating cooling water system from scaling, pipe corrosion, and microbial growth without any other chemicals. Thus circulating cooling water system can achieve zerodischarge of wastewater. 展开更多
关键词 ION EXCHANGE SOFTENING and ALKALIZATION circulating cooling water Zerodischarge
下载PDF
Laccase Immobilized on Mesoporous Silica Materials and Its Corrosion Inhibition Performance in Circulating Cooling Water System 被引量:2
5
作者 Liu Fang Lü Yucui +3 位作者 Zhong Huiyun Zhang Shuang Fan Fengtao Zhao Chaocheng 《China Petroleum Processing & Petrochemical Technology》 SCIE CAS 2015年第4期8-19,共12页
Mesoporous SiO_2 microspheres were synthesized using the sol-gel method and were characterized by TEM, FT-IR and BET techniques. The diameter of the microspheres is about 100—150 nm, and the average mesopore diameter... Mesoporous SiO_2 microspheres were synthesized using the sol-gel method and were characterized by TEM, FT-IR and BET techniques. The diameter of the microspheres is about 100—150 nm, and the average mesopore diameter is 2.55 nm, while the specific surface area is 1 088.9 m2/g. Mesoporous SiO_2 microspheres adsorb glutaraldehyde and immobilize laccase by means of the aldehyde group in glutaral which can react with the amidogen of laccase. The immobilization conditions were optimized at a glutaraldehyde concentration of 0.75%, a crosslinking time of 8 h, a laccase concentration of 0.04 L/L and an immobilization time of 10 h. When diesel leakage concentration was 80 mg/L, the highest corrosion inhibition efficiency of immobilized laccase reached 49.23%, which was slightly lower than the corrosion inhibition efficiency of free laccase(59%). The diesel degradation ratio could reach up to 45%. It has been proved that the immobilized laccase could degrade diesel to inhibit corrosion. 展开更多
关键词 固定化条件 循环冷却水系统 漆酶 缓蚀性能 硅材料 介孔 交联时间 FT-IR
下载PDF
电化学水处理技术降低循环水硬度的实验研究 被引量:1
6
作者 李火银 员佳琦 +3 位作者 李攀 程应伟 朱学智 于新功 《水处理技术》 CAS CSCD 北大核心 2024年第3期37-41,47,共6页
使用电化学法处理某焦化企业实际循环水的实验,探究了循环水的硬度和碱度去除率随处理时间的变化情况。分析了电流密度、水力停留时间、极板间距等实验操作参数以及商用阻垢剂对电解效果和能耗的影响。结果表明:硬度和碱度去除率随处理... 使用电化学法处理某焦化企业实际循环水的实验,探究了循环水的硬度和碱度去除率随处理时间的变化情况。分析了电流密度、水力停留时间、极板间距等实验操作参数以及商用阻垢剂对电解效果和能耗的影响。结果表明:硬度和碱度去除率随处理时间呈现先上升后平稳的趋势,且碱度去除率总是高于硬度去除率;电流密度为70 A/m^(2)、水力停留时间为6 min、极板间距为3 cm时电解效果最佳,硬度和碱度去除率可达27%以上,单位能耗低至13 kWh/kg;商用阻垢剂对电解效果具有阻碍作用。 展开更多
关键词 循环冷却水 电化学 电解效果 单位能耗 阻垢剂
下载PDF
QDQ2-1型水电解制氢设备冷却循环水控制改进方法研究
7
作者 张捷军 梁建平 +1 位作者 柯莉萍 蒋珍姣 《气象水文海洋仪器》 2024年第3期38-40,共3页
为了保障制氢设备的良好运行,文章进行水电解制氢设备冷却循环水控制改进方法的研究,利用温度控制电路将电解槽温度控制在预设范围,使水电解制氢设备始终工作在最佳温度。通过10个月的试用检验,设备未出现超温停机现象,改造效果理想。... 为了保障制氢设备的良好运行,文章进行水电解制氢设备冷却循环水控制改进方法的研究,利用温度控制电路将电解槽温度控制在预设范围,使水电解制氢设备始终工作在最佳温度。通过10个月的试用检验,设备未出现超温停机现象,改造效果理想。研究方法具有在同型号制氢设备中推广的可行性。 展开更多
关键词 制氢系统 冷却循环水 改进
下载PDF
水能风机在循环水冷却系统的应用
8
作者 叶海云 单龙玉 +1 位作者 李军 王子昊 《氯碱工业》 CAS 2024年第3期32-34,共3页
介绍了循环水冷却系统中采用水能风机代替大功率电动机实现节能降耗的实施措施,分析了改造后带来的经济效益。
关键词 水能风机 循环水 冷却系统 节能降耗
下载PDF
焦炭与不锈钢耦合阴极的电化学水软化性能研究
9
作者 王俊达 王立达 +3 位作者 赵津 刘锦程 邓海涛 刘贵昌 《工业水处理》 CAS CSCD 北大核心 2024年第3期97-103,共7页
以304不锈钢网作为外层支撑床,锯齿不锈钢网作为内部支撑结构,在复合锯齿网的锯齿空隙中填充焦炭,制备了一种由焦炭与不锈钢两种材料耦合的填充床电极,用于解决电化学水软化阴极无法长期高效运行的问题。探究了最优的电极结构参数,结果... 以304不锈钢网作为外层支撑床,锯齿不锈钢网作为内部支撑结构,在复合锯齿网的锯齿空隙中填充焦炭,制备了一种由焦炭与不锈钢两种材料耦合的填充床电极,用于解决电化学水软化阴极无法长期高效运行的问题。探究了最优的电极结构参数,结果表明,在阴阳极间距、外层平网孔径和表观电流密度分别为1.5 cm、20目、80 A/m^(2)时,电极对总硬度为700 mg/L的模拟循环冷却水的软化速率达到最佳,为46.873 g(/m^(2)·h)。当电极表面被垢层覆盖导致软化速率大幅下降时,通过振动方式对电极进行再生,研究了电极的使用寿命,结果表明,维持电极连续工作37 d,电极对循环冷却水仍保持较高的软化速率,可维持电化学水软化系统的长期高效运行。本研究可为解决电化学水软化阴极因无法有效再生导致的电化学水软化系统性能下降问题提供参考。 展开更多
关键词 电化学水软化 阴极再生 长寿命电极 循环冷却水
下载PDF
充水式潜水电机温度场仿真分析
10
作者 李佳欣 鲍晓华 +2 位作者 狄冲 燕靖文 朱庆龙 《电气工程学报》 CSCD 北大核心 2024年第1期141-149,共9页
为了避免充水式潜水电机在运行过程中局部过热导致绝缘失效,造成匝间短路故障的问题,提高电机运行的可靠性,以一台500k W充水式潜水电机为例,搭建了充水式潜水电机包括冷却器、外部水道、吸水罩在内的三维全域温度场仿真模型。模型对定... 为了避免充水式潜水电机在运行过程中局部过热导致绝缘失效,造成匝间短路故障的问题,提高电机运行的可靠性,以一台500k W充水式潜水电机为例,搭建了充水式潜水电机包括冷却器、外部水道、吸水罩在内的三维全域温度场仿真模型。模型对定子槽内部分进行了简化的同时考虑了定子槽内冷却水的流通,进一步提高了温度场仿真的精度。最后,对充水式潜水电机内外循环散热过程进行了仿真分析,并通过搭建充水式潜水电机试验平台对温度场仿真结果进行了验证。 展开更多
关键词 充水式潜水电机 温度场仿真 全域等效模型 循环冷却过程
下载PDF
循环冷却水系统的电化学水质稳定技术案例分析
11
作者 张延进 张泽坤 +4 位作者 徐星 韩英强 高宪 江波 徐浩 《工业水处理》 CAS CSCD 北大核心 2024年第2期184-189,共6页
水垢沉积和金属腐蚀会导致循环冷却水系统传热效率下降和能耗增加,严重影响工业生产的安全稳定运行。以某厂循环水系统的电化学除垢设备为案例,通过分析其处理效果和经济效益,为电化学技术处理循环冷却水的应用推广提供依据。现场所得... 水垢沉积和金属腐蚀会导致循环冷却水系统传热效率下降和能耗增加,严重影响工业生产的安全稳定运行。以某厂循环水系统的电化学除垢设备为案例,通过分析其处理效果和经济效益,为电化学技术处理循环冷却水的应用推广提供依据。现场所得运行数据表明,该厂所采用的电化学除垢设备能够有效改善水质,防止结垢,控制循环冷却水系统的腐蚀情况。每年减少循环水系统补水量和排污量各4.38×10^(5) t,并显著降低药剂投加量。经济核算显示该电化学系统每年可节省约212.9万元。 展开更多
关键词 循环冷却水 电化学除垢 水质稳定技术
下载PDF
电磁场与电化学对循环冷却水系统中设备腐蚀及结垢的影响
12
作者 陈翔宇 王东强 +2 位作者 张元鸣 黎刚生 董学武 《中原工学院学报》 CAS 2024年第2期19-25,34,共8页
循环冷却水对工业生产至关重要,但若长期使用,会使传输管道及换热设备产生腐蚀和结垢,这一直是循环冷却水使用过程中存在的顽疾。将环保、高效、时兴的新技术电磁场(旋磁加能器)和电化学(吸垢仪)创新地联合运用到水质更差的中水中,探索... 循环冷却水对工业生产至关重要,但若长期使用,会使传输管道及换热设备产生腐蚀和结垢,这一直是循环冷却水使用过程中存在的顽疾。将环保、高效、时兴的新技术电磁场(旋磁加能器)和电化学(吸垢仪)创新地联合运用到水质更差的中水中,探索这种联合技术在循环冷却水系统上的防腐、防垢效果。通过搭建的小型工业水循环系统平台,验证了这种联合技术可有效减少循环冷却水系统的腐蚀和结垢问题,改善循环冷却水系统的运行状态,另外,为工业循环水企业提供了将中水用作循环冷却水的新思路,可为企业增加经济效益,实现节能减排。 展开更多
关键词 循环冷却水 电磁场 电化学 腐蚀 结垢
下载PDF
Removal of kathon by UV-C activated hydrogen peroxide:Kinetics,mechanisms,and enhanced biodegradability assessment
13
作者 Jinzhi Cui Guiqiao Wang +6 位作者 Xing Rong Wensu Gao Yaxin Lu Yawen Luo Lichao Zhang Zhongfa Cheng Canzhu Gao 《Chinese Journal of Chemical Engineering》 SCIE EI CAS CSCD 2024年第1期178-187,共10页
Kathon(CMI-MI),a mixture of 5-chloro-2-methyl-4-isothiazolin-3-one(CMI)and 2-methyl-4-isothiazolin-3-one(MI),was extensively used in industry as a nonoxidizing biocide or disinfectant.However,it would show adverse eff... Kathon(CMI-MI),a mixture of 5-chloro-2-methyl-4-isothiazolin-3-one(CMI)and 2-methyl-4-isothiazolin-3-one(MI),was extensively used in industry as a nonoxidizing biocide or disinfectant.However,it would show adverse effects on aquatic life when it is discharged into surface water.In this study,the removal performance,parameter influence,degradation products and enhancement of subsequent biodegradation of CMI-MI in UV/H_(2)O_(2)system were systematically investigated.The degradation rate of CMI-MI could reach 90%under UV irradiation for 20 min when the dosage of H_(2)O_(2)was 0.3 mmol·L^(–1).The DOC(dissolved organic carbon)mineralization rate of CMI-MI could reach 35%under certain conditions([H_(2)O_(2)]=0.3 mmol·L^(–1),UV irradiation for 40 min).kobs was inversely proportional to the concentration of CMI-MI and proportional to the concentration of H_(2)O_(2).The degradation rate of CMIMI was almost unchanged in the pH range from 4 to 10.Except the presence of CO_(3)^(2-)inhibited the removal rate of CMI-MI,SO_(4)^(2-),Cl^(-),NO_(3)^(-),and NH_(4)^(+) did not interfere with the degradation of CMI-MI in the system.It was found that UV/H_(2)O_(2)system had lower energy consumption and more economic advantage compared with UV/PS system by comparing the EEO(electric energy per order)values under the same conditions.Two main organic products were identified,namely HCOOH and CH_(3)NH_(2).There’s also the formation of Cl^(-)and SO_(4)^(2-).After UV and UV/H_(2)O_(2)photolysis,the biochemical properties of CMI-MI solution were obviously improved,especially the UV/H_(2)O_(2)treatment effect was better,indicating that UV/H_(2)O_(2)technology is expected to combine with biotechnology to remove CMI-MI effectively and environmentally friendly from wastewater. 展开更多
关键词 Kathon UV/H_(2)O_(2) Biological degradation circulating cooling water
下载PDF
氯离子对不锈钢冷却水管道腐蚀的分析及研究
14
作者 李辉 姚月姣 《工程建设与设计》 2024年第13期65-67,共3页
我国北方某已建项目中,不锈钢冷却水管道上出现多处孔蚀缺陷,论文以此为案例展开研究,分析不锈钢腐蚀的机理,研究不锈钢腐蚀的影响因素,提出适用于同类项目的氯离子浓度限值和相应的防腐解决方案,如改进焊接工艺、投加化学药剂、优化补... 我国北方某已建项目中,不锈钢冷却水管道上出现多处孔蚀缺陷,论文以此为案例展开研究,分析不锈钢腐蚀的机理,研究不锈钢腐蚀的影响因素,提出适用于同类项目的氯离子浓度限值和相应的防腐解决方案,如改进焊接工艺、投加化学药剂、优化补水水质、保持系统的定期运行等。 展开更多
关键词 工业冷却循环水 不锈钢管道 氯离子 腐蚀 浓度限值
下载PDF
基于热泵技术的余热回收供热系统
15
作者 杨晓玮 慕佳琪 +3 位作者 李孜绪 刘媛媛 徐胜利 刘晓华 《节能》 2024年第5期67-70,共4页
传统热电厂的循环冷却水中含有大量的低品位余热,利用热泵技术对其进行回收,能够显著提升供热系统的能源利用效率,有利于实现节能减排和“碳中和”目标。设计基于单、双吸收式热泵机组的余热回收供热系统,旨在有效利用循环冷却水中的余... 传统热电厂的循环冷却水中含有大量的低品位余热,利用热泵技术对其进行回收,能够显著提升供热系统的能源利用效率,有利于实现节能减排和“碳中和”目标。设计基于单、双吸收式热泵机组的余热回收供热系统,旨在有效利用循环冷却水中的余热,增加供热能力并分析系统性能。结果表明,与传统供热系统相比,两种余热回收供热系统均可显著回收循环冷却水的热量,提高系统供热量并大幅减少能源消耗,带来可观的经济收益;双吸收式热泵机组系统展现出更优异的热力性能,具备显著的节能减排优势。分析循环冷却水入口温度和一次网回水温度对双吸收式热泵机组性能的影响,发现循环冷却水温度对系统性能影响较大,随着循环冷却水温度的升高,系统的供热量增加比例、节约标煤量和新增供热面积均增加,而一次网回水温度对系统性能的影响较小,随一次网回水温度的升高,系统的供热量增加比例、节约标准煤量和新增供热面积几乎不变。 展开更多
关键词 吸收式热泵 循环冷却水 余热回收 供热系统 热电厂
下载PDF
高炉软水密闭循环冷却系统水温调控分析与探讨
16
作者 李亚光 净晓星 +1 位作者 王旭旦 刘磊 《冶金动力》 2024年第1期48-51,共4页
介绍了首钢股份4 000 m~3高炉的软水密闭循环冷却系统的工艺流程、系统特点与运行效果。高炉软水密闭循环系统采用闭式冷却塔冷却降温,冷却水采用循环供水方式,通过冷却水量的合理分配,实现对软水的可靠降温。根据十年来的实际运行情况... 介绍了首钢股份4 000 m~3高炉的软水密闭循环冷却系统的工艺流程、系统特点与运行效果。高炉软水密闭循环系统采用闭式冷却塔冷却降温,冷却水采用循环供水方式,通过冷却水量的合理分配,实现对软水的可靠降温。根据十年来的实际运行情况,对软水密闭循环冷却系统水温调控存在的问题进行了整改,有效提升了降温能力,提高了系统的供水安全性。 展开更多
关键词 高炉 软水密闭循环 冷却水 降温
下载PDF
高炉风口水腔结垢原因及防治措施
17
作者 赵锦 贾利涛 +4 位作者 张玉瑶 董舒宇 武建龙 黄俊杰 徐萌 《冶金动力》 2024年第3期50-55,共6页
针对某钢铁厂高炉风口水腔结垢问题,对垢样进行X射线衍射(XRD)检测,检测结果显示垢样的主要成分为CaSO_(4)、CaSO_(4)·2H_(2)O和CaSO_(4)·0.5H_(2)O。分析高炉风口循环冷却水水质和原有阻垢剂性能,提出相应的改善措施,调控循... 针对某钢铁厂高炉风口水腔结垢问题,对垢样进行X射线衍射(XRD)检测,检测结果显示垢样的主要成分为CaSO_(4)、CaSO_(4)·2H_(2)O和CaSO_(4)·0.5H_(2)O。分析高炉风口循环冷却水水质和原有阻垢剂性能,提出相应的改善措施,调控循环冷却水硬度在400 mg/L以下,并在原阻垢剂中配加6 mg/L乙二胺四甲叉磷酸钠(EDTMPS),有效避免了风口水垢的形成,提高了高炉风口的寿命。 展开更多
关键词 风口 水垢 阻垢剂 硬度 循环冷却水
下载PDF
炼化企业污水回用至循环水系统的分析研究
18
作者 叶晓林 赵玥 孙飞 《给水排水》 CSCD 北大核心 2024年第5期66-72,共7页
我国水资源匮乏的问题日益突出,工业企业节水减排工作的重要性逐步提升。对某炼化企业的两套生化装置污水的水质条件及各生产单元的用水量等数据进行分析,初步确认了适合回用至循环冷却水系统的煤化工生化装置污水,水量为140 m3/h。在... 我国水资源匮乏的问题日益突出,工业企业节水减排工作的重要性逐步提升。对某炼化企业的两套生化装置污水的水质条件及各生产单元的用水量等数据进行分析,初步确认了适合回用至循环冷却水系统的煤化工生化装置污水,水量为140 m3/h。在不同的回用方案条件下,根据循环水水质标准计算该方案可以达到的最高浓缩倍数,得到两种优化回用方案,实现了污水回用背景下的循环水系统高浓缩倍数(≥5)运行。后续将继续在循环水药剂优化和污水处理单元提标改造等方面进行研究,进一步提升污水回用率,实现节水减排的更高目标。 展开更多
关键词 生化装置 水质 循环水 回用方案 炼化企业
下载PDF
西北地区某大型调相机外冷系统结垢成因解析与防垢对策研究
19
作者 李国斌 牛征 +6 位作者 谢强 郑金池 夏忠林 王彦明 梁博文 罗海平 马双忱 《热力发电》 CAS CSCD 北大核心 2024年第3期167-176,共10页
调相机外冷水系统换热器和冷却塔填料层表面结垢会严重影响冷却塔的换热效率,危及调相机安全运行。为了更有效地提出防垢措施,查明结垢成因,采用扫描电子显微镜-X射线能谱分析仪、X射线衍射分析仪、傅立叶红外光谱仪等表征手段对垢样微... 调相机外冷水系统换热器和冷却塔填料层表面结垢会严重影响冷却塔的换热效率,危及调相机安全运行。为了更有效地提出防垢措施,查明结垢成因,采用扫描电子显微镜-X射线能谱分析仪、X射线衍射分析仪、傅立叶红外光谱仪等表征手段对垢样微观形貌以及化学组分进行检测分析,对循环系统补充水、循环水采用电感耦合等离子体质谱仪以及化学分析方法进行检测分析。测试结果表明:该外冷却系统内结垢的主要成分为CaCO_(3)、SiO_(2)以及CaSiO_(3);冷却系统结垢与系统循环水没有排污措施,过高浓缩倍率运行以及地区风沙侵入有很大关系。结合上述分析及当地特殊的地理位置与天气条件,提出若干防垢措施与建议,有助于该类冷却系统现场运行时更有针对性地提出防垢措施,保障调相机运维的经济性以及安全性。 展开更多
关键词 调相机 循环冷却水 成分分析 防垢措施
下载PDF
基于正交实验的电化学法处理循环冷却水的应用研究
20
作者 易慧 王文兵 +3 位作者 曹雯雯 刘上月 余轶峰 米东旭 《印染助剂》 CAS 2024年第4期31-35,56,共6页
为解决循环冷却水成垢问题,采用实验室小试和中试研究相结合的方法,以广西柳州钢铁集团有限公司焦化厂的循环冷却水为研究对象,通过正交实验设计,探索了阴极极板材料、极板间距、电压、反应时间4个因素的交互影响,构建了正交实验表。实... 为解决循环冷却水成垢问题,采用实验室小试和中试研究相结合的方法,以广西柳州钢铁集团有限公司焦化厂的循环冷却水为研究对象,通过正交实验设计,探索了阴极极板材料、极板间距、电压、反应时间4个因素的交互影响,构建了正交实验表。实验结果表明,阴极材料的选择和实验参数的调整对电化学去除循环冷却水中Ca^(2+)和Cl^(-)的效果具有明显影响。极差分析结果显示,阴极材料对除垢效果的影响最为显著,而电压对除氯效果的影响最为显著。通过中试研究对小试实验结果进行验证,取得了显著的经济效益。 展开更多
关键词 正交实验 电化学法 循环冷却水 除垢
下载PDF
上一页 1 2 98 下一页 到第
使用帮助 返回顶部