Effects of spot size on the operation mode of Ga As photoconductive semiconductor switch employing extrinsic photoconductivity

To guide the illuminating design to improve the on-state performances of gallium arsenide(GaAs)photoconductive semiconductor switch(PCSS),the effect of spot size on the operation mode of GaAsPCSS based on a semi-insulating wafer with a thickness of 1 mm,triggered by a 1064-nm extrinsic laser beam with the rectangular spot,has been investigated experimentally.It is found that the variation of the spot size in length and width can act on the different parts of the output waveform integrating the characteristics of the linear and nonlinear modes,and then significantly boosts the PCSS toward different operation modes.On this basis,a two-channel model containing the active and passive parts is introduced to interpret the relevant influencing mechanisms.Results indicate that the increased spot length can peak the amplitude of static domains in the active part to enhance the development of the nonlinear switching,while the extended spot width can change the distribution of photogenerated carriers on both parts to facilitate the linear switching and weaken the nonlinear switching,which have been proved by comparing the domain evolutions under different spot sizes.

Energy Storage Operation Modes in Typical Electricity Market and Their Implications for China

As the Chinese government proposes ambitious plans to promote low-carbon transition,energy storage will play a pivotal role in China’s future power system.However,due to the lack of a mature electricity market environment and corresponding mechanisms,current energy storage in China faces problems such as unclear operational models,insufficient cost recovery mechanisms,and a single investment entity,making it difficult to support the rapid development of the energy storage industry.In contrast,European and American countries have already embarked on certain practices in energy storage operation models.Through exploration of key issues such as investment entities,market participation forms,and cost recovery channels in both front and back markets,a wealth of mature experiences has been accumulated.Therefore,this paper first summarizes the existing practices of energy storage operation models in North America,Europe,and Australia’s electricity markets separately from front and back markets,finding that perfect market mechanisms and reasonable subsidy policies are among the main drivers for promoting the rapid development of energy storage markets.Subsequently,combined with the actual development of China’s electricity market,it explores three key issues affecting the construction of costsharing mechanisms for energy storage under market conditions:Market participation forms,investment and operation modes,and cost recovery mechanisms.Finally,in line with the development expectations of China’s future electricitymarket,suggestions are proposed fromfour aspects:Market environment construction,electricity price formation mechanism,cost sharing path,and policy subsidy mechanism,to promote the healthy and rapid development of China’s energy storage industry.

An Improved Multi-Objective Hybrid Genetic-Simulated Annealing Algorithm for AGV Scheduling under Composite Operation Mode

This paper presents an improved hybrid algorithm and a multi-objective model to tackle the scheduling problem of multiple Automated Guided Vehicles(AGVs)under the composite operation mode.The multi-objective model aims to minimize the maximum completion time,the total distance covered by AGVs,and the distance traveled while empty-loaded.The improved hybrid algorithm combines the improved genetic algorithm(GA)and the simulated annealing algorithm(SA)to strengthen the local search ability of the algorithm and improve the stability of the calculation results.Based on the characteristics of the composite operation mode,the authors introduce the combined coding and parallel decoding mode and calculate the fitness function with the grey entropy parallel analysis method to solve the multi-objective problem.The grey entropy parallel analysis method is a combination of the grey correlation analysis method and the entropy weighting method to solve multi-objective solving problems.A task advance evaluation strategy is proposed in the process of crossover and mutation operator to guide the direction of crossover and mutation.The computational experiments results show that the improved hybrid algorithm is better than the GA and the genetic algorithm with task advance evaluation strategy(AEGA)in terms of convergence speed and solution results,and the effectiveness of the multi-objective solution is proved.All three objectives are optimized and the proposed algorithm has an optimization of 7.6%respectively compared with the GA and 3.4%compared with the AEGA in terms of the objective of maximum completion time.

High-speed performance self-powered short wave ultraviolet radiation detectors based onκ(ε)-Ga_(2)O_(3)

High-speed solar-blind short wavelength ultraviolet radiation detectors based onκ(ε)-Ga_(2)O_(3)layers with Pt contacts were demonstrated and their properties were studied in detail.Theκ(ε)-Ga_(2)O_(3)layers were deposited by the halide vapor phase epitaxy on patterned GaN templates with sapphire substrates.The spectral dependencies of the photoelectric properties of struc-tures were analyzed in the wavelength interval 200-370 nm.The maximum photo to dark current ratio,responsivity,detectiv-ity and external quantum efficiency of structures were determined as:180.86 arb.un.,3.57 A/W,1.78×10^(12) Hz^(0.5)∙cm·W^(-1) and 2193.6%,respectively,at a wavelength of 200 nm and an applied voltage of 1 V.The enhancement of the photoresponse was caused by the decrease in the Schottky barrier at the Pt/κ(ε)-Ga_(2)O_(3)interface under ultraviolet exposure.The detectors demon-strated could functionalize in self-powered mode due to built-in electric field at the Pt/κ(ε)-Ga_(2)O_(3)interface.The responsivity and external quantum efficiency of the structures at a wavelength of 254 nm and zero applied voltage were 0.9 mA/W and 0.46%,respectively.The rise and decay times in self-powered mode did not exceed 100 ms.

Experimental investigation of the polarityswitching process with different bipolar ionic liquid thruster operating frequencies

The bipolar ionic liquid thruster employs ionic liquid as a propellant to discharge positively and negatively charged high-energy particles under an alternating current(AC)power source,effectively suppressing electrochemical reaction and ensuring charge neutrality.Determining an optimal AC supply power source frequency is critical for sustained stable thruster operation.This study focuses on the emission characteristics of the ionic liquid thruster under varied AC conditions.The AC power supply was set within the frequency range of 0.5-64 Hz,with eight specific frequency conditions selected for experimentation.The experimental results indicate that the thruster operates steadily within a voltage range of±1470 to±1920 V,with corresponding positive polarity current ranging from 0.41 to 4.91μA and negative polarity current ranging from−0.49 to−4.10μA.During voltage polarity switching,an emission delay occurs,manifested as a prominent peak signal caused by circuit capacitance characteristics and a minor peak signal resulting from liquid droplets.Extended emission test was conducted at 16 Hz,demonstrating approximately 1 h and 50 min of consistent emission before intermittent discharge.These findings underscore the favorable impact of AC conditions within the 8-16 Hz range on the self-neutralization capability of the ionic liquid thruster.

Discussion on Biomass Fuel Operation Model Dominated by Tobacco Straw

With the gradually popularization of replacing coal tobacco leaf flue-curing technology with biomass fuel, the operation of raw materials collection and transportation links faces many problems. In this paper, the existing problems in view of biomass fuel operation dominated by tobacco straw in current tobacco leaf flue-curing were analyzed, and the 3 kinds of fuel operation modes （＂contracting processing mode, displacement mode and commercialization mode＂） were put forward, each of which was also briefly analyzed, with the aim to expand the way of thinking about biomass raw materials processing by cooperative organization.

Multi-mode process monitoring based on a novel weighted local standardization strategy and support vector data description

There are multiple operating modes in the real industrial process, and the collected data follow the complex multimodal distribution, so most traditional process monitoring methods are no longer applicable because their presumptions are that sampled-data should obey the single Gaussian distribution or non-Gaussian distribution. In order to solve these problems, a novel weighted local standardization(WLS) strategy is proposed to standardize the multimodal data, which can eliminate the multi-mode characteristics of the collected data, and normalize them into unimodal data distribution. After detailed analysis of the raised data preprocessing strategy, a new algorithm using WLS strategy with support vector data description(SVDD) is put forward to apply for multi-mode monitoring process. Unlike the strategy of building multiple local models, the developed method only contains a model without the prior knowledge of multi-mode process. To demonstrate the proposed method's validity, it is applied to a numerical example and a Tennessee Eastman(TE) process. Finally, the simulation results show that the WLS strategy is very effective to standardize multimodal data, and the WLS-SVDD monitoring method has great advantages over the traditional SVDD and PCA combined with a local standardization strategy(LNS-PCA) in multi-mode process monitoring.

An Integrated Dynamic Model of Ocean Mining System and Fast Simulation of Its Longitudinal Reciprocating Motion

An integrated dynamic model of China＇s deep ocean mining system is developed and the fast simulation analysis of its longitudinal reciprocating motion operation processes is achieved. The seafloor tracked miner is built as a three-dimensional single-body model with six-degree-of-freedom. The track-terrain interaction is modeled by partitioning the track-terrain interface into a certain number of mesh elements with three mutually perpendicular forces, including the normal force, the longitudinal shear force and the lateral shear force, acting on the center point of each mesh element. The hydrodynamic force of the miner is considered and applied. By considering the operational safety and collection efficiency, two new mining paths for the miner on the seafloor are proposed, which can be simulated with the established single-body dynamic model of the miner. The pipeline subsystem is built as a three-dimensional multi-body discrete element model, which is divided into rigid elements linked by flexible connectors. The flexible connector without mass is represented by six spring-damper elements. The external hydrodynamic forces of the ocean current from the longitudinal and lateral directions are both considered and modeled based on the Morison formula and applied to the mass center of each corresponding discrete rigid element. The mining ship is simplified and represented by a general kinematic point, whose heave motion induced by the ocean waves and the longitudinal and lateral towing motions are considered and applied. By integrating the single-body dynamic model of the miner and the multi-body discrete element dynamic model of the pipeline, and defining the kinematic equations of the mining ship, the integrated dynamic model of the total deep ocean mining system is formed. The longitudinal reciprocating motion operation modes of the total mining system, which combine the active straight-line and turning motions of the miner and the ship, and the passive towed motions of the pipeline, are proposed and simulated with the developed 3D dynamic model. Some critical simulation results are obtained and analyzed, such as the motion trajectories of key subsystems, the velocities of the buoyancy modules and the interaction forces between subsystems, which in a way can provide important theoretical basis and useful technical reference for the practical deep ocean mining system analysis, operation and control.

Low Power Consumption Distributed-Feedback Quantum Cascade Lasers Operating in Continuous-Wave Mode above 90℃ at λ～7.2μm

We report on the design and fabrication of λ-7.2μm distributed feedback quantum cascade lasers lot very high temperature cw operation and low electrical power consumption. The cw operation is reported above 90℃. For a 2-mm-long and 10-μm-wide laser coated with high-reflectivity on the rear facet, more than 170mW of output power is obtained at 20℃ with a threshold power consumption of 2.4 W, corresponding to 30mW with a threshold power consumption of 3.9 W at 90℃. Robust single-mode emission with a side-mode suppression ratio above 25 dB is continuously tunable by the heat sink temperature or injection current.

Operation Mode on Pulse Modulation in Atmospheric Radio Frequency Glow Discharges

The discharge operation regime of pulse modulated atmospheric radio frequency （RF） glow discharge in helium is investigated on the duty cycle and frequency of modulation pulses. The characteristics of radio frequency discharge burst in terms of breakdown voltage, alpha（s）- gamma（γ） mode transition voltage and current are demonstrated by the discharge current voltage characteristics. The minimum breakdown voltage of RF discharge burst was obtained at the duty cycle of 20% and frequency of 400 kHz, respectively. The α-γ mode transition of RF discharge burst occurs at higher voltage and current by reducing the duty cycle and elevating the modulation frequency before the RF discharge burst evolving into the ignition phase, in which the RF discharge burst can operate stably in the γ mode. It proposes that the intensity and stability of RF discharge burst can be improved by manipulating the duty cycle and modulation frequency in pulse modulated atmospheric RF glow discharge.

The Architecture and Operation Mode of Virtual Supply Chain

Virtual supply chain, as a modern collaborative mode of enterprises, is important to decrease the cost and improve the efficiency and the quality of supply chains, and to satisfy customers. Based on the analysis of the conception and characteristics of the virtual supply chain, the architecture of virtual supply chain is built, and corresponding objects, tasks, information and technologies are described. Three operation modes-Order-driven, manufacturer-centered, and retailer-centered are researched. As a case, virtual supply chain is applied in the electronic commerce and networked customization system of ceramic products.

Research on representative brand and operation mode of second-hand clothing in Europe

In order to study the current situation and operation mode of second-hand clothing brand in Europe,this paper makes a field investigation on the second-hand clothing shops in European countries.Through classification of the inspected shops,five representative brands with certain popularity and influence and different operation modes in Europe are selected out from high-grade antique boutiques,non-profit charity organizations,professional retailers and middle-grade consignment shops in the second-hand clothing market.This paper analyzes and discusses the development history of stores,the source of goods,the form of stores,and the operation mode,so as to provide a reference for the development and standardization of the second-hand clothing market in China.

An integrated operation mode for green logistics of enterprises

The integrated operation mode of green logistics is a new enterprise＇s logistics operation and management mode concerning, environment issues based on the traditional integrated mode. Through comparative study on the integrated operation mode of logistics based on self.operation, the operation mode of an integrated logistics of enterprises based on TPL the green-supply chain management, and the operation mode of eco-iadustrial park （EIP）, a relatively complete objective system structure is put forward for the integrated operation mode of green logistics of enterprises. Furthermore, the correspondent practical mode is also set up to help enterprises, especially for the manufacturing companies, not only improve the environment effectively, but support the technological framework for the enterprise＇s economic performance and social benefits in order to realize economic, social and environmental benefits are concerned.

Operational Mode Identification Based on Sliding Time Window Method and Eigensystem Realization Algorithm

The identification result of operational mode is eurychoric while operational mode identification is investigated under ambient excitation,which is influenced by the signal size and the time interval.The operational mode identification method,which is based on the sliding time window method and the eigensystem realization algorithm(ERA),is investigated to improve the identification accuracy and stability.Firstly,the theory of the ERA method is introduced.Secondly,the strategy for decomposition and implementation is put forward,including the sliding time window method and the filtration method of modes.At last,an example is studied,where the model of a cantilever beam is built and the white noise exciting is input.Results show that the operational mode identification method can realize the modes,and has high robustness to the signal to noise ratio and signal size.

Oxidization resistance of Ni76Cr19AlTi valve alloy at temperatures under operating mode of heavy-duty engines

The oxidization resistance of the Ni76Cr19A1Ti alloy was studied by a static oxidization experiment at 600-800℃. The results show that the oxidation behavior of the alloy can be explained by a kinetic equation： （△m/S）2 = Kpt ＋ C, where Kp is a kinetic constant of the nickel-base alloy. The higher the experimental temperature, the higher the value of Kp. It is discovered that the microstructure of the oxide scales is compact and the thickness of it is less than 10 μm The oxidization of the alloy is in the first grade. It is also found that the oxide scales are mainly composed of Cr2O3 and TiO2. Chrome and titanium react more easily with oxygen at temperatures under the operating mode.

Operation Modes and Control Schemes for Internet-Based Teleoperation System with Time Delay

Teleoperation system plays an important role in executing task under hazard environment. As the computer networks such as the Internet are being used as the communication channel of teleoperation system, varying time delay causes the overall system unstable and reduces the performance of transparency. This paper proposed twelve operation modes with different control schemes for teleoperation on the Internet with time delay. And an optimal operation mode with control scheme was specified for teleoperation with time delay, based on the tradeoff between passivity and transparency properties. It experimentally confirmed the validity of the proposed optimal mode and control scheme by using a simple one DOF master-slave manipulator system.

Discussi on on IPTV Operations Modes

IPTV is a promising broadband video service to which telecom operators are attaching great importance. However,there are many challenges especially to confirm operations modes. Under the circumstances of industry regulation in China,the telecom operators may adopt a standard IPTV mode,IP+TV mode or pure IP mode according to specific requirements when deploying IPTV services that are personalized and interactive. The development of IPTV faces numerous difficulties such as unclear supervision policy,industry barrier difficult to be removed,vague profit models,and imperfect technology specifications. However,the general development tendency decides a bright future of IPTV.

Research on the Effects of Train Operation Mode for Vehicle Energy Consumption

The research background is based on great consumption of urban rail transit energy, through summarizing the research of scholars at home and abroad, the comprehensive research including train operation pattern, the train traction characteristics and optimization design of integrated research has carried out in this paper, by using OPENTRACK software simulation to verify the optimization results according to different line features finally. The aim of this paper is to explore ways and methods of traction strategy optimization under the condition of trains timing energy saving. The main research contents of this paper are based on the research status at home and abroad, first of all, the different operating modes of the train running on the line are analysed, including the time saving mode, the energy saving mode and timing energy saving mode, and quantitative analysed the influence of different operation modes on vehicle energy consumption. The influence factors and traction calculation method of energy consumption of train running are studied. Firstly, the factors that affect the energy consumption of the train are analysed, including the basic facilities and transport organization mode. On the basis of this, the train load and running status of the train are analysed, and the model of the train movement and energy consumption are calculated. The OPENTRACK software is used to establish the actual circuit model, and the simulation is verified. The results show that the reasonable operation mode of the train operation mode can greatly reduce the energy consumption.

Research on the development mode of long-term nursing insurance ——taking Qingdao as an example

With the gradual development of society, scientific and technological progress, aging gradually aggravated, has become a hot topic of society. People to old age, self-care ability than in the past, not only suffer from disease, life has become difficult, coupled with the large number of empty nest family, the cost of care is also very high, whether it is to receive home care or professional institutions of care have great difficulties. Therefore, the community should be a large number of people with long-term care needs of the appropriate economic compensation, in this context, long-term care insurance is born. As a leading city in Shandong Province, Qingdao has introduced long-term care insurance and achieved good results. This paper analyzes the practical problems faced by Qingdao, that is, the development background of Qingdao long-term nursing insurance model, obtains the deficiency of Qingdao long-term nursing insurance, and then puts forward the corresponding countermeasures, and then ponders how to choose the long-term nursing insurance model of our country＇s future development.