A Yb optical clock with a lattice power enhancement cavity

We construct a power enhancement cavity to form an optical lattice in an ytterbium optical clock.It is demonstrated that the intra-cavity lattice power can be increased by about 45 times,and the trap depth can be as large as 1400Er when laser light with a power of only 0.6 W incident to the lattice cavity.Such high trap depths are the key to accurate evaluation of the lattice-induced light shift with an uncertainty down to~1×10-18.By probing the ytterbium atoms trapped in the power-enhanced optical lattice,we obtain a 4.3 Hz-linewidth Rabi spectrum,which is then used to feedback to the clock laser for the close loop operation of the optical lattice clock.We evaluate the density shift of the Yb optical lattice clock based on interleaving measurements,which is-0.46(62)mHz.This result is smaller compared to the density shift of our first Yb optical clock without lattice power enhancement cavity mainly due to a larger lattice diameter of 344μm.

Finesse measurement for high-power optical enhancement cavity

Finesse is a critical parameter for describing the characteristics of an optical enhancement cavity(OEC). This paper first presents a review of finesse measurement techniques, including a comparative analysis of the advantages, disadvantages, and potential limitations of several main methods from both theoretical and practical perspectives. A variant of the existing method called the free spectral range(FSR) modulation method is proposed and compared with three other finesse measurement methods, i.e., the fast-switching cavity ring-down(CRD) method, the rapidly swept-frequency(SF) CRD method, and the ringing effect method. A high-power OEC platform with a high finesse of approximately 16000 is built and measured with the four methods. The performance of these methods is compared, and the results show that the FSR modulation method and the fast-switching CRD method are more suitable and accurate than the other two methods for high-finesse OEC measurements. The CRD method and the ringing effect method can be implemented in open loop using simple equipment and are easy to perform. Additionally, recommendations for selecting finesse measurement methods under different conditions are proposed, which benefit the development of OEC and its applications.

Controllable optical bistability in a Fabry-Pérot cavity with a nonlinear three-dimensional Dirac semimetal

Optical bistability(OB)is capable of rapidly and reversibly transforming a parameter of an optical signal from one state to another,and homologous nonlinear optical bistable devices are core components of high-speed all-optical communication and all-optical networks.In this paper,we theoretically investigated the controllable OB from a Fabry-Pérot(FP)cavity with a nonlinear three-dimensional Dirac semimetal(3D DSM)in the terahertz band.The OB stems from the third-order nonlinear bulk conductivity of the 3D DSM and the resonance mode has a positive effect on the generation of OB.This FP cavity structure is able to tune the OB because the transmittance and the reflectance can be modulated by the Fermi energy of the 3D DSM.We believe that this FP cavity configuration could provide a reference concept for realizing tunable bistable devices.

Continuous-wave optical enhancement cavity with 30-kW average power

Optical enhancement cavity(OEC)is a powerful tool for fundamental research and diagnostics.In this paper,the progress of a continuous-wave OEC to realize of megawatt cavity for a novel light source based on a steady-state microbunching(SSMB)mechanism,is reported.After efficiently suppressing all external noise and optimizing the alignment,mode-matching,and polarization matching,stable and long-term locking is achieved with the help of two feedback loops.The modal instability phenomenon caused by the surface thermoelastic deformation is observed.A pair of D-shape mirrors are utilized to remove the high-order modes.Finally,an intra-cavity average power of 30 kW is reached.

Inverse design and realization of an optical cavity-based displacement transducer with arbitrary responses

Optical cavity has long been critical for a variety of applications ranging from precise measurement to spectral analysis.A number of theories and methods have been successful in describing the optical response of a stratified optical cavity,while the inverse problem,especially the inverse design of a displacement sensitive cavity,remains a significant challenge due to the cost of computation and comprehensive performance requirements.This paper reports a novel inverse design methodology combining the characteristic matrix method,mixed-discrete variables optimization algorithm,and Monte Carlo method-based tolerance analysis.The material characteristics are indexed to enable the mixed-discrete variables optimization,which yields considerable speed and efficiency improvements.This method allows arbitrary response adjustment with technical feasibility and gives a glimpse into the analytical characterization of the optical response.Two entirely different light-displacement responses,including an asymmetric sawtooth-like response and a highly symmetric response,are dug out and experimentally achieved,which fully confirms the validity of the method.The compact Fabry-Perot cavities have a good balance between performance and feasibility,making them promising candidates for displacement transducers.More importantly,the proposed inverse design paves the way for a universal design of optical cavities,or even nanophotonic devices.

Optically pumped wavelength-tunable lasing from a GaN beam cavity with an integrated Joule heater pivoted on Si

Dynamically tunable laser sources are highly promising for realizing visionary concepts of integrated photonic circuits and other applications. In this paper, a Ga N-based laser with an integrated PN junction heater on Si is fabricated.The photoluminescence properties of the Ga N beam cavity are controlled by temperature, and the Joule heater provides electrically driven regulation of temperature. These two features of the cavity make it possible to realize convenient tuning of the lasing properties. The multi-functional Ga N beam cavity achieves optically pumped lasing with a single mode near 362.4 nm with a high Q-factor of 1394. The temperature of this device increases by 0–5℃ under the Joule heating effect. Then, electrical control of the lasing mode is demonstrated. The lasing resonant peak shows a continuous redshift of about 0.5 nm and the device also exhibits dynamic switching of its lasing mode. The lasing modulation can be ascribed to temperature-induced reduction of the bandgap. Our work may be of benefit for external optical modulation in future chip-based optoelectronic devices.

A Single Mode980 nm In Ga As/Ga As/Al Ga As Large Optical Cavity Quantum Well Laser with Low Vertical Divergence Angle

To achieve high optical power as well as low vertical divergence angle,a new kind of optim ized large opti- cal cavity (L OC) structure is applied to a ridge waveguide 980 nm In Ga As/ Ga As/ Al Ga As m ulti- quantum well laser.The optical power density in the waveguide is successfully reduced.The maxim um output power is more than 40 0 m W with a slope efficiency of 0 .89W/ A and the far- field vertical divergence angle is lowered to 2 3°.

Vibration insensitive optical ring cavity

The mounting configuration of an optical ring cavity is optimized for vibration insensitivity by finite element analysis. A minimum response to vertical accelerations is found by simulations made for different supporting positions.

A tunnel regenerated coupled multi-active-region large optical cavity laser with a high quality beam

A novel coupled multi-active-region large optical cavity structure cascaded by a tunnel junction is proposed to solve the problems of facet catastrophic optical damage （COD） and the large vertical divergence caused by the thin emitting area in conventional laser diodes. For a laser with three active regions, a slope efficiency as high as 1.49 W/A, a vertical divergence angle of 17.4~, and a threshold current density of 271 A/cm~ are achieved. By optimizing the structural parameters, the beam quMity is greatly improved, and the level of the COD power increases by more than two times compared with that of the conventional laser.

Superconducting Nanowire Single Photon Detector with Optical Cavity

Increasing the detection efficiency （DE） is a hot issue in the development of the superconducting nanowire single photon detector （SNSPD）. In this work, a cavity-integrated structure coupled to the SNSPD is used to enhance the light absorption of nanowire. Ultra-thin Nb films are successfully prepared by magnetron sputtering, which are used to fabricate Nb/Al SNSPD with the curve of lOOnm and the square area of 4 × 4μm2 by sputtering and the lift-off method. To characterize the optical and electrical performance of the cavity-integrated SNSPD, a reliable cryogenic research system is built up based on a He3 system. To satisfy the need of light coupling, a packaging structure with collimator is conducted. Both DE and the dark count rates increase with lb. It is also found that the DE of SNSPD with cavities can be up to 0.17% at the temperature of 0.7K under the infrared light of 1550nm, which is obviously higher than that of the SNSPD directly fabricated upon silicon without any cavity structure.

Dual-Wavelength Bad Cavity Laser as Potential Active Optical Frequency Standard

We experimentally realize the dual-wavelength bad cavity laser for the first time. As the Cs cell temperature is kept between 118℃ and 144℃, both the 1359nm and 147Ohm lasing outputs of dual-wavelength bad cavity laser are detected. The laser output power of dual-wavelength bad cavity laser is measured when changing the 455 nm pumping laser frequency and power at 127℃ Cs cell temperature. Both the 1359 nm laser and the 1470 nm laser are working at the deep bad cavity regime, and the ratio between the linewidth of cavity mode and the laser gain bandwidth a ≈ 40 for 1359nm and 1470nm lasers. The 147Ohm laser linewidth is measured to be 407.3Hz. The dual-wavelength bad cavity laser operating on atomic transitions demonstrated here has a potential in the application as a stable optical local oscillator, even an active optical frequency standard directly in the future.

Experimental Scheme of 633 nm and 1359 nm Good-Bad Cavity Dual-Wavelength Active Optical Frequency Standard

The experimental scheme of 633 nm and 1359 nm good-bad cavity dual-wavelength active optical frequency stan- dard is proposed, where He-Ne 633nm and Cs 1359nm stimulated emissions are working at good-cavity and bad-cavity regimes, respectively. The cavity length is stabilized by locking the 633nm output frequency to a super-cavity with the Pound Drever-Hall （PDH） technique. The frequency stability of 1359 nm bad-cavity stim- ulated emission output is then expected to be further improved by at least 1 order of magnitude than the 633nm PDH system due to the suppressed cavity pulling effect of active optical clock, and the quantum limited linewidth of 1359nm output is estimated to be 72.5 mHz.

Iterative physical optics method based on efficient occlusion judgment with bounding volume hierarchy technology

This paper builds a binary tree for the target based on the bounding volume hierarchy technology,thereby achieving strict acceleration of the shadow judgment process and reducing the computational complexity from the original O(N^(3))to O(N^(2)logN).Numerical results show that the proposed method is more efficient than the traditional method.It is verified in multiple examples that the proposed method can complete the convergence of the current.Moreover,the proposed method avoids the error of judging the lit-shadow relationship based on the normal vector,which is beneficial to current iteration and convergence.Compared with the brute force method,the current method can improve the simulation efficiency by 2 orders of magnitude.The proposed method is more suitable for scattering problems in electrically large cavities and complex scenarios.

Optical feedback characteristics in a helium neon laser with a birefringent internal cavity

The output characteristics of optical feedback in a helium neon laser with a birefringent internal cavity are studied systematically in five different regions of the gain curve for the two orthogonally polarized modes. When the laser operates in the two end regions of the laser gain curve, one of the two orthogonally polarized modes will be a leading one in optical feedback. Strong mode competition can be observed. However, when the laser operates in the middle region of the laser gain curve, the two modes can oscillate equally with optical feedback. Besides the intensity of the two polarized lights, the total light intensity is also studied at the same time. M-shaped optical feedback curves are found. Particularly, when the average intensities of the two lights are comparable, the intensity modulation curve of the total light is doubled, which can be used to improve the resolution of an optical feedback system.

Design and test of the microwave cavity in an optically-pumped Rubidium beam frequency standard

We are developing a compact rubidium atomic beam frequency standard with optical pumping and detection. The cavity for microwave interrogation is an important part of the clock. The cavity in our design is a Ramsey-type, E-bend one, which is the same as the conventional method in most cesium beam clocks. Requirements for the design are proposed based on the frequency shift associated with the cavity. The basic structure of the cavity is given by theoretical analysis and detailed dimensions are determined by means of electromagnetic field simulation with the help of commercial software.The cavity is manufactured and fabricated successfully. The preliminary test result of the cavity is given, which is in good agreement with the simulation. The resonant frequency is 6.835 GHz, equal to the clock transition frequency of87 Rb, and the loaded quality factor is 500. These values are adjustable with posts outside the cavity. Estimations on the Ramsey line width and several frequency shifts are made.

Quantum logic operations on two distant atoms trapped in two optical-fibre-connected cavities

Based on the coupling of two distant three-level atoms in two separate optical cavities connected with two optical fibres, schemes on the generation of several two-qubit logic gates are discussed under the conditions of △ = δ- 2v cos πk/2 〉〉 g/2 and v-g. Discussion and analysis of the fidelity, gate time and experimental setups show that our schemes are feasible with current optical cavity, atomic trap and optical fibre techniques. Moreover, the atom-cavityfibre coupling can be used to generate an N-qubit nonlocal entanglement and transfer quantum information among N distant atoms by arranging N atom cavity assemblages in a line and connecting each two adjacent cavities with two optical fibres.

Generation of multi-atom W states via Raman transition in an optical cavity

A simple scheme is proposed to generate the W state of N A-type neutral atoms trapped in an optical cavity via Raman transition. Conditional on no photon leakage from the cavity, the N-qubit W state can be prepared perfectly by turning on a classical coupling field for an appropriate time. Compared with the previous ones, our scheme requires neither individual laser addressing of the atoms, nor demand for controlling N atoms to go through an optical cavity simultaneously with a constant velocity. We investigate the influence of cavity decay using the quantum jump approach and show that the preparation time decreases and the success probability increases with atom number because of a collective enhancement of the coupling.

Mechanical effects of light on the ■-type three-level atom in a high-finesse optical cavity

A theoretical study is carried out for the modification and implication of the effect on the type three level atom in a high-finesse optical cavity driven by light field including spontaneous emission and the cavity decay. Analytic expressions for the dipole force, the friction force, the optical potentials and the friction coefficient are obtained. Then the numerical and graphical methods are used to investigate the friction coefficient with the controlling parameters. It is shown that the friction coefficient is strongly dependent on the controlling parameters. The cooling rate can increase by one order of magnitude more than that of a two-level atomic system. The reason can be given using the dressed states and the Sisyphus cooling mechanism, which would stimulate further experimental investigations.

Electromagnetically induced transparency of single Λ-type three-level atoms in a high-finesse optical cavity

We study the features of electromagnetically induced transparency（EIT） in a single Λ-type three-level atom placed in a high-finesse cavity under the action of a coupling laser and a probe laser.Our calculations show that three transparency windows appear when the pump strength is large enough.This can be explained by the residual pump in the cavity mostly resulting in energy splitting.The level ｜3 is split into four slightly different energy levels,and interference takes place between the excitation pathways.Furthermore,it is also shown that the frequencies of the EIT windows can be tuned by changing the coupling field detuning 2,and that the reflection profile is very sensitive to the cavity field detuning △c.

Application of the Spectrum Peak Positioning Technology Based on BP Neural Network in Demodulation of Cavity Length of EFPI Fiber Optical Sensor

An Extrinsic Fabry-Perot Interferometric (EFPI) fiber optical sensor system is an online testing system for the gas density. The system achieves the measurement of gas density information mainly by demodulating the cavity length of EF- PI fiber optical sensor. There are many ways to achieve the demodulation of the cavity length. For shortcomings of the big intensity demodulation error and complex structure of phase demodulation, this paper proposes that BP neural net-work is used to locate the special peak points in normalized interference spectrum and combining the advantages of the unimodal and bimodal measurement achieves the demodulation of the cavity length. Through online simulation and actual measurement, the results show that the peak positioning technology based on BP neural network can not only achieve high-precision demodulation of the cavity length, but also achieve an absolute measurement of cavity length in large dynamic range.