About Some Aspects of Use of Optical Sensors for Monitoring the Aquatic Environment

Multi-channel polarization optical technology is increasingly used for prompt monitoring of water systems.Optical devices during the assessment of water quality determine the intensity of light through the studied aquatic environment.Spectrophotometric devices measure the spectrum of weakening of light through the aquatic environment.Spectroellipsometric devices receive spectra in vertical and horizontal polarizations.The presented article develops an adaptive optical hardware and image system for monitoring water bodies.The system is combined.It consists of 2 parts:1)automated spectrophotometer-refractometer,and 2)adaptive spectroellipsometer.The system is equipped with a corresponding algorithmic and software,including algorithms for identifying spectral curves,databases and knowledge of spectral curves algorithms for solving reverse problems.The presented system is original since it differs from modern foreign systems by a new method of spectrophotometric and spectroellipsometric measurements,an original elemental base of polarization optics and a comprehensive mathematical approach to assessing the quality of a water body.There are no rotating polarization elements in the system.Therefore,this makes it possible to increase the signal-to-noise ratio and,as a result,improve measurement stability and simplify multichannel spectrophotometers and spectroellipsometers.The proposed system can be used in various water systems where it is necessary to assess water quality or identify the presence of a certain set of chemical elements.

A Modified Principal Component Analysis Method for Honeycomb Sandwich Panel Debonding Recognition Based on Distributed Optical Fiber Sensing Signals

The safety and integrity requirements of aerospace composite structures necessitate real-time health monitoring throughout their service life.To this end,distributed optical fiber sensors utilizing back Rayleigh scattering have been extensively deployed in structural health monitoring due to their advantages,such as lightweight and ease of embedding.However,identifying the precise location of damage from the optical fiber signals remains a critical challenge.In this paper,a novel approach which namely Modified Sliding Window Principal Component Analysis(MSWPCA)was proposed to facilitate automatic damage identification and localization via distributed optical fiber sensors.The proposed method is able to extract signal characteristics interfered by measurement noise to improve the accuracy of damage detection.Specifically,we applied the MSWPCA method to monitor and analyze the debonding propagation process in honeycomb sandwich panel structures.Our findings demonstrate that the training model exhibits high precision in detecting the location and size of honeycomb debonding,thereby facilitating reliable and efficient online assessment of the structural health state.

Dispersion Monitoring Techniques in High Bit-rate Optical Communication Systems

For the efficient dynamic dispersion compensation, it is essential to monitor the dispersion accurately. The existing main dispersion monitoring techniques in high bit-rate optical communication systems are presented as well as their operating principles and research progress. The advantages and disadvantages of these methods are analyzed and discussed.

A Self-Referenced Fiber-Optic Refractive Index Sensor for Cure Monitoring of Epoxy Composites

A self referenced fiber optic refractive index sensor is developed to measure quantitative cure extent of epoxy. In case the sensor is applied to in situ cure monitoring of epoxy composites, each sensor embedded in different location within the structure is self referenced and can be normalized to a common scale. Therefore, the real time comparative of each sensor’s output becomes possible and variations in the extent of cure at different locations can be monitored. The developed sensor was used to monitor the isothermal cure of an epoxy system. The output of the sensor was compared with the results of the differential scanning calorimetry (DSC). The self referencing function of the sensor is confirmed.

Construction monitoring of lock head base plate using distributed optical fibre sensing technique

The concrete hydration heat release process of the base plate is monitored using Roman optical time domain reflectometry（ROTDR） sensing sensors. The monitoring data shows that the internal maximum temperature of the base plate is about 54 ℃ after the concrete was cured for 120 h. The fiber Bragg grating （FBG） temperature sensors are adopted to measure the surface temperature of the concrete and the temperature results are used to compensate the data measured by the pulse-prepump Brillouin optical time-domain analyzer （PPP-BOTDA） to obtain the real concrete surface strain of the base plate. The monitoring data is analyzed to obtain a clear understanding of the strain state of the base plate under the effect of concrete hydration heat release. The monitoring results demonstrate the potential of distributed optical fibre sensing techniques as a powerful tool in real-time construction monitoring, and also provide an important insight into the design, construction and maintenance of large hydraulic structures.

Fiber optic monitoring of an anti-slide pile in a retrogressive landslide

Anti-slide piles are one of the most important reinforcement structures against landslides,and evalu-ating the working conditions is of great significance for landslide mitigation.The widely adopted analytical methods of pile internal forces include cantilever beam method and elastic foundation beam method.However,due to many assumptions involved in calculation,the analytical models cannot be fully applicable to complex site situations,e.g.landslides with multi-sliding surfaces and pile-soil interface separation as discussed herein.In view of this,the combination of distributed fiber optic sensing(DFOS)and strain-internal force conversion methods was proposed to evaluate the working conditions of an anti-sliding pile in a typical retrogressive landslide in the Three Gorges reservoir area,China.Brillouin optical time domain reflectometry(BOTDR)was utilized to monitor the strain distri-bution along the pile.Next,by analyzing the relative deformation between the pile and its adjacent inclinometer,the pile-soil interface separation was profiled.Finally,the internal forces of the anti-slide pile were derived based on the strain-internal force conversion method.According to the ratio of calculated internal forces to the design values,the working conditions of the anti-slide pile could be evaluated.The results demonstrated that the proposed method could reveal the deformation pattern of the anti-slide pile system,and can quantitatively evaluate its working conditions.

Optical Surface Monitoring系统跟踪运动靶区的位置精度和剂量精度验证

目的:评估Optical Surface Monitoring System(OSMS)测量靶区运动的几何精度和使用OSMS跟踪运动靶区放疗时的剂量精度。方法:①分别使用OSMS与锥形束CT监测腹部模体的位置,通过移动治疗床使模体产生位移和旋转,对比二者对模体位置的测量结果;②用呼吸运动平台搭载MatriXX二维电离室阵列,测量不同跟踪阈值时模体内相对剂量,分别与计划剂量分布对比,分析不同跟踪阈值时计划验证的gamma通过率。结果:OSMS和锥形束CT系统对模体平移和旋转预设偏移的测量结果差异很小,使用OSMS门控技术时OSMS的阈值越小gamma通过率越高,相对剂量分布与计划剂量的一致性也越好。结论:OSMS系统对模体表面位置监测精度高,可以应用到实际放射治疗的辅助摆位。使用OSMS门控技术跟踪运动靶区可以提高靶区的剂量精度,而且对患者不附加任何电离辐射,适合应用于分次间的辅助摆位和分次内的靶区跟踪。

基于改进CGAN的海冰SAR-to-Optical影像转换

遥感海冰监测是当前研究热点,通过条件生成对抗网络(CGAN)将海冰SAR影像转换成光学影像,可获得全天时全天候且形象直观的监测数据,但该方法得到的转换结果存在影像模糊、纹理弱化和颜色失真等问题。本文针对以上问题设计了改进的CGAN网络,综合当前的改进方式,新模型在网络结构上加入了空洞空间金字塔模块并设计了加入交叉特征融合模块的跳跃连接,使用结构相似性和L1范数联合损失函数。本文选取东波弗特海地区5景Sentinel-1影像和7景Sentinel-2影像开展实验,实验结果表明,改进CGAN转换的影像具有更好的视觉效果,峰值信噪比(PSNR)提高了3.4 dB,结构相似性(SSIM)提高了0.11,均方根误差(RMSE)降低了13%,并且经过转换后的影像比SAR影像海冰分类结果准确度提高了7.33%。

Structural Deformation Monitoring of Flight Vehicles Based on Optical Fiber Sensing Technology:A Review and Future Perspectives

Structural deformation monitoring of flight vehicles based on optical fiber sensing(OFS)technology has been a focus of research in the field of aerospace.After nearly 30 years of research and development,Chinese and international researchers have made significant advances in the areas of theory and methods,technology and systems,and ground experiments and flight tests.These advances have led to the development of OFS technology from the laboratory research stage to the engineering application stage.However,a few problems encountered in practical applications limit the wider application and further development of this technology,and thus urgently require solutions.This paper reviews the history of research on the deformation monitoring of flight vehicles.It examines various aspects of OFS-based deformation monitoring including the main varieties of OFS technology,technical advantages and disadvantages,suitability in aerospace applications,deformation reconstruction algorithms,and typical applications.This paper points out the key unresolved problems and the main evolution paradigms of engineering applications.It further discusses future development directions from the perspectives of an evolution paradigm,standardization,new materials,intelligentization,and collaboration.

An Optical Fiber Sensor Probe Using a PMMA/CPR Coated Bent Optical Fiber as a Transducer for Monitoring Trace Ammonia

Ammonia sensors have broad spectrum of applications for industrial process control as well as for environ-mental monitoring. An optical fiber ammonia sensor probe has been developed by using a bent optical fiber having dual poly(methyl methacrylate) (PMMA)/chlorophenol red (CPR) coatings as a transducer. This sen-sor probe was tested for monitoring trace ammonia in gas samples using air as sample matrix. The reaction of ammonia with CPR causes a color change of the reagent, which was detected by using fiber optic evanes-cent wave absorption spectrometry as a sensing signal. By adopting a dual layer coating structure, the sensor probe has faster response compared to a sensor using a broadly accepted sensing reagent-immobilized poly-mer coating structure. The sensor developed in this work is sensitive, has a detection limit of 2.7 ppb NH3 in air, which is the most sensitive among the reported optical fiber ammonia sensors to the best knowledge of the authors. The sensor is also reversible and has a response time of 25 minutes. The features of high sensi-tivity, reversibility and reasonable response time make this sensor technique very attractive for air quality monitoring.

Distributed fiber optic sensors for tunnel monitoring:A state-of-the-art review

Distributed fiber optic sensors(DFOSs)possess the capability to measure strain and temperature variations over long distances,demonstrating outstanding potential for monitoring underground infrastructure.This study presents a state-of-the-art review of the DFOS applications for monitoring and assessing the deformation behavior of typical tunnel infrastructure,including bored tunnels,conventional tunnels,as well as immersed and cut-and-cover tunnels.DFOS systems based on Brillouin and Rayleigh scattering principles are both considered.When implementing DFOS monitoring,the fiber optic cable can be primarily installed along transverse and longitudinal directions to(1)measure distributed strains by continuously adhering the fiber to the structure’s surface or embedding it in the lining,or(2)measure point displacements by spot-anchoring it on the lining surface.There are four critical aspects of DFOS monitoring,including proper selection of the sensing fiber,selection of the measuring principle for the specific application,design of an effective sensor layout,and establishment of robust field sensor instrumentation.These four issues are comprehensively discussed,and practical suggestions are provided for the implementation of DFOS in tunnel infrastructure monitoring.

Multiple-impairment monitoring for optical duobinary system based on delay-tap asynchronous sampling

A technique using artificial neural networks trained with parameters derived from delay tap plots for optical performance monitoring in 40 Gbit/s duobinary system is demonstrated. Firstly, the optical signal is delay tap sampled to obtain two-dimensional histogram, known as delay tap plots. Secondly, the features of delay tap plots are extracted to train the feed forward, three-layer preceptor structure artificial neural networks. Finally, the outputs of trained neural network are used to monitor optical duobinary signal impairments. Simulation of optical signal noise ratio （ OSNR）, chromatic dispersion （CD）, and differential group delay （DGD） monitoring in 40 Gbit/s optical duo- binary system is presented. The proposed monitoring scheme can accurately identify simultaneous impairments without requiring synchronous sampling or data clock recovery. The proposed technique is simple, cost-effective and suitable for in-service distributed OPM.

Optical Remote-sensing Monitoring and Forecasting of Atmospheric Pollution in Huaibei Area, China

Huaibei is an energy city. Coal as the primary energy consumption brings a large number of regional pollution in Huaibei area. Differential optical absorption spectroscopy （DOAS） as optical remote sensing technology has been applied to monitor regional average concen- trations and inventory of nitrogen dioxide, sulfur dioxide and ozone. DOAS system was set up and applied to monitor the main air pollutants in Huaibei area. Monitoring data were obtained from 7 to 28 August, 2011. Monitoring results show measurements in controlling pollution are effective, and emissions of pollutants are up to the national standard in Huaibei area. Prediction model was also created to track changing trend of pollutions. These will provide raw data support for effective evaluation of environmental quality in Huaibei area.

Optically powered gas monitoring system using single-mode fibre for underground coal mines

We present an optically powered,intrinsically safe gas monitoring system to measure four essential environmental gases(CH_(4),CO_(2),CO and O_(2)),together with ambient temperature and pressure,for underground mines.The system is based on three key technologies developed at UNSW:(1)power-over-fbre(PoF)at 1550 nm using a single industry-standard,low-cost single-mode fbre(SMF)for both power delivery and information transmission,(2)liquid–crystal-based optical transducers for optical telemetry,and(3)ultra-low power consumption design of all electronics.Together,this approach allows each gas monitoring station to operate with less than 150 mW of optical power,meeting the intrinsic safety requirements specifed by the IEC60079-28 standard.A 2-month feld trial at BMA’s Broadmeadow underground mine proved the cabling compatibility to the mine’s existing optical network and the stability of the system performance.Compared with conventional electrically powered gas sensors,this technology bypasses the usual roadblocks of underground gas monitoring where electrical power is either unsafe or unavailable.Furthermore,using one fbre for both power delivery and communication enables longer distance coverage,reduces optical cabling and increases multiplexing possibilities and data throughput for better awareness of underground environment.

Distributed optical fiber acoustic sensor for in situ monitoring of marine natural gas hydrates production for the first time in the Shenhu Area,China

The distributed acoustic sensor(DAS)uses a single optical cable as the sensing unit,which can capture the acoustic and vibration signals along the optical cable in real-time.So it is suitable for monitoring downhole production activities in the process of oil and gas development.The authors applied the DAS system in a gas production well in the South China Sea for in situ monitoring of the whole wellbore for the first time and obtained the distributed acoustic signals along the whole wellbore.These signals can clearly distinguish the vertical section,curve section,and horizontal production section.The collected acoustic signal with the frequency of approximately 50 Hz caused by the electric submersible pump exhibit a signal-to-noise ratio higher than 27 dB.By analyzing the acoustic signals in the production section,it can be located the layers with high gas production rates.Once an accurate physical model is built in the future,the gas production profile will be obtained.In addition,the DAS system can track the trajectory of downhole tools in the wellbore to guide the operation.Through the velocity analysis of the typical signals,the type of fluids in the wellbore can be distinguished.The successful application of the system provides a promising whole wellbore acoustic monitoring tool for the production of marine gas hydrate,with a good application prospect.

Instantaneous frequency measurement using two parallel I/Q modulators based on optical power monitoring

A scheme for instantaneous frequency measurement(IFM)using two parallel I/Q modulators based on optical power monitoring is proposed.The amplitude comparison function(ACF)can be constructed to establish the relationship between the frequency of radio frequency(RF)signal and the power ratio of two optical signals output by two I/Q modulators.The frequency of RF signal can be derived by measuring the optical power of the optical signals output by two I/Q modulators.The measurement range and measurement error can be adjusted by controlling the delay amount of the electrical delay line.The feasibility of the scheme is verified,and the corresponding measurement range and measurement error of the system under different delay amounts of the electrical delay line are given.Compared with previous IFM schemes,the structure of this scheme is simple.Polarization devices,a photodetector and an electrical power meter are not used,which reduces the impact of the environmental disturbance on the system and the cost of the system.In simulation,the measurement range can reach 0 GHz-24.5 GHz by adjusting the delay amount of the electrical delay lineτ=20 ps.The measurement error of the scheme is better at low frequency,and the measurement error of low frequency 0 GHz-9.6 GHz can reach-0.1 GHz to+0.05 GHz.

Optical Label-Based Cost-Effective DWDM Optical Network Performance Monitoring Using Low-Bandwidth PD with Novel SRS Mitigation DSP

Large-scale dense wavelength division multiplexing(DWDM)multi-channel performance monitoring is one of the indispensable technologies for the flexible optical networks.The existing Labelbased monitoring scheme requires expensive optical demultiplexing components/equipment to avoid the influence of stimulated Raman scattering(SRS),which is not only costly and bulky,but also could not monitor the wavelength channels simultaneously.In this paper,a low-cost,high-accuracy monitoring scheme based on Optical Label Method is proposed for DWDM networks,where the optical channel power and node identification(ID),as the main monitoring targets that both can indicate or evaluate the channel connection status,could be efficiently monitored.In the scheme,a novel digital signal processing(DSP)method of SRS mitigation is proposed and demonstrated,and an asynchronous code-division multiple access(A-CDMA)based digital label encoding and decoding method is adopted to distinguish the node ID so that channel initial added node can be accurately verified,thereby wavelength connection status can be reliably monitored by combining the channel power and node ID information.The simulation results show that each wavelength channel power and node ID can be accurately monitored only by low bandwidth photoelectric detector(PD)under the condition of 80 wavelengths and 10 spans at C-band.

Optical broadband monitoring of thin film growth

This contribution is focused on applications of spectroscopic methods for the precise control of deposition processes. In this context, the present study gives a review on selected combinations of conventional and ion deposition techniques with different broadband online spectrophotometric systems. Besides two systems operating in the VIS- and NIR-spectral range in combination with ion processes, also a monochromator system developed for conventional deposition processes in the DUV/VUV-spectral range will be discussed. The considerations will be concluded by a comparison of the major advantages of the specific combinations of processes with online monitoring concepts and by a brief outlook concerning future challenges.

Development of Dual-light Path Monitoring System of Optical Thin-film Thickness

The accurate monitoring of optical thin-film thickness is a key technique for depositing optical thin-film. For existing coating equipments, which are low precision and automation level on monitoring thin-film thickness, a new photoelectric control and analysis system has been developed. In the new system, main techniques include a photoelectric system with dual-light path, a dual-lock-phase circuit system and a comprehensive digital processing-control-analysis system.The test results of new system show that the static and dynamic stabilities and the control precision of thin-film thickness are extremely increased. The standard deviation of thin-film thickness, which indicates the duplication of thin-film thickness monitoring, is equal to or less than 0.72%. The display resolution limit on reflectivity is 0.02 %. In the system, the linearity of drift is very high, and the static drift ratio approaches zero.

RESEARCH ON OPTICAL METHOD OF MONITORING PHOTOCATHODE PROCESS

The principle of an optical method of photocathode processing control, which is one ofphotocathode processing monitoring techniques, is discussed. A designed monitoring apparatus is describedand has been applied to investigate the optical parameters of multialkali photoemitter during the process offabrication. Some actual schemes using the method to monitor the preparation of photocathodεs are sug-gested.