Electrically and Optically Bistable Operation in an Integration of a 1310 nm DFB Laser and a Tunneling Diode

We experimentally demonstrate an In P-based hybrid integration of a single-mode DFB laser emitting at around 1310 nm and a tunneling diode. The evident negative differential resistance regions are obtained in both electrical and optical output characteristics. The electrical and optical bistabilities controlled by the voltage through the tunneling diode are also measured. When the voltage changes between 1.46 V and 1.66 V, a 200-mV-wide hysteresis loop and an optical power ON/OFF ratio of 17 dB are obtained. A side-mode suppression ratio of the integrated device in the ON state is up to 43 dB. The tunneling diode can switch on/off the laser within a very small voltage range compared with that directly controlled by a voltage source.

Research and Review on the Development of Mechanical and Electrical Integration of System Function Principle and Related Technologies

In this paper, we conduct research on the development of mechanical and electrical integration of system function principle and related technologies. Along with the rapid and continuous development of modem science and technology, it ＇ s for the penetration and cross of different subjects great push, the more important is caused by technological revolution in the field of engineering and mechanical engineering field under the rapid development of computer technology and microelectronic technology and penetration to the mechanical and electrical integration, which is formed by the mechanical industry lead to trigger a particularly large changes in the mechanical industry management system and mode of production, product and technical structure, composition and function, thus result in industrial production from the previous mechanical electrification progressively electromechanical integration which lead the trend of the current technology.

First-Principles Study of Structural Stabilities, Electronic and Optical Properties of SrF2 under High Pressure

An investigation of structural stabilities, electronic and optical properties of SrF2 under high pressure is conducted using a first-principles calculation based on density functional theory （DFT） with the plane wave basis set as implemented in the CASTEP code. Our results predict that the second high-pressure phase of SrF2 is of a Ni2In- type structure, and demonstrate that the sequence of the pressure-induced phase transition of SrF2 is the fluorite structure （Fm3m） to the PbC12-type structure （Pnma）, and to the Ni2In-type phase （P63/mmc）. The first and second phase transition pressures are 5. 77 and 45.58 GPa, respectively. The energy gap increases initially with pressure in the Fm3m, and begins to decrease in the Pnma phases at 30 GPa. The band gap overlap metallization does not occur up to 210 GPa. The pressure effect on the optical properties is discussed.

Effects of Annealing Temperature on Structural and Optical Properties of ZnO Thin Films

The effects of annealing temperature on the structural and optical properties of ZnO films grown on Si （100） substrates by sol-gel spin-coating are investigated. The structural and optical properties are characterized by x-ray diffraction, scanning electron microscopy and photoluminescence spectra. X-ray diffraction analysis shows the crystal quality of ZnO films becomes better after annealing at high temperature. The grain size increases with the temperature increasing. It is found that the tensile stress in the plane of ZnO films first increases and then decreases with the annealing temperature increasing, reaching the maximum value of 1.8 GPa at 700℃. PL spectra of ZnO films annealed at various temperatures consists of a near band edge emission around 380 nm and visible emissions due to the electronic defects, which are related to deep level emissions, such as oxide antisite （OZn）, interstitial oxygen （Oi）, interstitial zinc （Zni） and zinc vacancy （VZn^-）, which are generated during annealing process. The evolution of defects is analyzed by PL spectra based on the energy of the electronic transitions.

Nonlinear Optical Properties and Ultrafast Dynamics of Undoped and Doped Bulk SiC

Ultrafast third-order nonlinear optical response of bulk 6H-SiC undoped and doped with different nitrogen concentrations are investigated utilizing femtosecond Z-scan and optical Kerr effect （OKE） techniques at the wavelength of 800hm. The Z-scan measurement shows that the third-order nonlinear optical susceptibilities of the doped samples are improved in comparison to the intrinsic sample. The OKE results additionally reveal that the instantaneous nonlinear optical response of the samples can be ascribed to the distortion of the electron cloud. The ultrafast transient spectroscopic measurements with the one-color and two-color pump-probe techniques demonstrate that the ultrafast recovery process in subpicosecond domain is induced by two-photon absorption process, while the slow relaxation component reflects the carrier dynamics of the excited electrons.

First-Principles Study of Electronic and Optical Properties of Y1-xCaxTiO3 （x=0, 0.25, 0.5, 0.75）

The full potential linearized augmented plane wave （FP-LAPW） method with the generalized gradient approximation （GGA） is applied to study the electronic and optical properties of perovskite-type compounds Y1-xCaxTiO3. The lattice parameters, magnetic moment, band structure, density of states and optical conductivity are obtained. The results show that the Ca ion plays an important role in the electronic properties and optical responses. Moreover, the optical properties including the dielectric function, absorption spectrum, extinction coefficient, energy-loss spectrum and refractive index are also discussed.

First-Principles Investigations of the Phase Transition and Optical Properties of Solid Oxygen

Using density-functional-theory calculations, a monoclinic metallic post-ζ phase （space group C2/c） is predicted at 215 GPa. The calculated phonon dispersion curves suggest that this structure is stable at least up to 310 GPa. Oxygen remains a molecular crystal and there is no dissociation in the related pressure range. Moreover, it is found that the phase transition from （ to post-ζ phase is attributed to phonon softening, The significant change in the optical properties can be used to identify the phase transition.

Mechanical Reinforcement and Piezoelectric Properties of PZT Ceramics Embedded with Nano-Crystalline

The double-scale lead zirconate titanate （PZT） piezoelectric ceramics were prepared by the solid state processing with PZT nano-crystalline and micro-powder. The microstructures, electrical and mechanical properties of the double-scale PZT are investigated. All the sintered ceramics exhibit a single perovskite structure and the grain size of the dou ble-scale PZT reduces due to the incorporation of PZT nano-crystalline. Compared to normal PZT, the mechanical properties increase significantly and the piezoelectric properties decrease slightly. Mechanisms responsible for the reinforcement of the double-scale PZT are discussed.

Mechanical Properties and Anisotropy in PbWO4 Single Crystal

The mechanical properties of PbWO4 （PWO） crystals grown by the vertical Bridgman method are systematically investigated using the microindentation technique. In the present work, the Vickers microhardness Hν, fracture toughness Kc, yield strength σy and friability index Bi of PbWO4 crystals are measured. The Vickers microhardness Hν on the （100） wafer is about 140 MPa, which means that PWO is a little soft＇＇ scintillator. The anisotropy of mechanical properties is also investigated under a steady load of 0.5 kg. The （100） wafer of the crystal exhibits combined mechanical properties more excellent than those of （111） and （001） wafers, and the values of Kc, σy, and Bi are 0.538 MPa＆#12539;m1/2, 51.11 kg/mm2 and 284.96 νm-1/2, respectively.

Mechanical and Magnetic Properties of Rh and RhH： First-Principles Calculations

Mechanical and magnetic properties of Rh in bcc, fcc structures and RhH in cubic structure are investigated by using first-principles calculations. Theoretical strengths of these structures are given for the first time. The results show that the NaCl-type cubic RhH has a lower bulk modulus and a theoretical strength larger than those of Rh in bcc and fcc structures. A strong magneto-volume effect of a transition from low magnetic moment-low cell volume＇＇ to high magnetic moment-large cell volume＇＇ is also found for both the bcc and fcc Rh structures as well as RhH.

Effect of Annealing on Microstructure and Electrical Characteristics of Doped Poly （3-Hexylthiophene） Films

The effect of annealing on the microstructure and electrical characteristics of poly （3-hexylthiophene） （P3HT） films doped with very small amounts of the electron acceptor 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane （F4-TCNQ） is studied. X-ray diffraction and UV-vis spectrum studies show that unlike the pure P3HT film, the thermal treatment on the doped fihns under an Ar atmosphere can effectively enhance the crystalline order of P3HT films, as well as successfully facilitate the orientation of the polymer chains. This improvement is attributed to the electrostatic force between P3HT and F4-TCNQ molecules. This force induces the polymer chains to crystallize and orient during the annealing process. As a result, annealing significantly improves performance, especially for the Ion/Ioff ratio of the TFTs based on the doped P3HT films.

Mechanical Integrity and Failure Analysis of Photovoltaic Modules under Simulated Snow Loads Using Pneumatic Airbag Setup

Photovoltaic (PV) modules have emerged as an ideal technology of choice for harvesting vastly available renewable energy resources. However, the efficiency of PV modules remains significantly lower than that of other renewable energy sources such as wind and hydro. One of the critical elements affecting a photovoltaic module’s efficiency is the variety of external climatic conditions under which it is installed. In this work, the effect of simulated snow loads was evaluated on the performance of PV modules with different types of cells and numbers of busbars. According to ASTM-1830 and IEC-1215 standards, a load of 5400 Pa was applied to the surface of PV modules for 3 hours. An indigenously developed pneumatic airbag test setup was used for the uniform application of this load throughout the test, which was validated by load cell and pressure gauge. Electroluminescence (EL) imaging and solar flash tests were performed before and after the application of load to characterize the performance and effect of load on PV modules. Based on these tests, the maximum power output, efficiency, fill factor and series resistance were determined. The results show that polycrystalline modules are the most likely to withstand the snow loads as compared to monocrystalline PV modules. A maximum drop of 32.13% in the power output and a 17.6% increase in series resistance were observed in the modules having more cracks. These findings demonstrated the efficacy of the newly established test setup and the potential of snow loads for reducing the overall performance of PV module.

Configuration of an optical waveguide interconnect mesh network based on EOPCB

An optical waveguide interconnect mesh network scheme for parallel multiprocessor systems based on an electro-optical printed circuit board （EOPCB） with multimode polymer waveguide is proposed. The system consists of 2×2 processor element chips interconnected in a mesh network configuration. An additional layer with optical waveguide structure is embedded in a conventional printed circuit board to construct the EOPCB. Vertical cavity surface emitting laser （VCSEL）/positive intrinsic-negative （PIN） arrays are ap- plied as the optical transmitters/receivers. Three 1 ~ 12 VCSEL/PIN parallel optical transmitting/receiving modules are used to provide 32 input/output optical channels required by the 2~2 chip-to-chip optical mesh interconnect system. The data rate in each optical channel is 3.125 Gbps and thus 10 Gbps parallel optical interconnect link for each direction of a chip is obtained. The optical signals from a processor element chip can be transmitted to another chip through optical waveguide interconnect embedded in the board. Thus the optical interconnect mesh network for parallel multiprocessor system can be implemented.

GKPA-联合全局与关键区域的光学-SAR中分辨率遥感影像场景分类

遥感影像场景分类是自然灾害检测和城市功能规划等实际应用的基础,因此研究遥感影像场景分类具有重要意义。基于深度学习的方法由于其强大的特征提取能力已经成为遥感影像场景分类领域最常用的方法,此类方法强烈依赖数据集的质量。现阶段场景分类领域的数据集大多为高分辨率的光学影像,易于提取有效的语义特征。在面对中分辨率场景时,影像中细节信息更匮乏,有效特征不够显著,场景分类具有更大难度,相较于高分辨率场景分类精度不够理想。在此情况下,利用其他模态的数据如合成孔径雷达(SAR)提供互补特征可以有效改善场景分类精度。考虑到以上现状,本文构建光学-SAR遥感影像场景分类数据集(OS-RSISC),基于此数据集进一步提出了一个联合全局与关键区域的感知注意力双模态场景分类框架(GKPA-RSSC)。实验结果显示GKPA-RSSC相较于对比方法具有最高的分类精度,总体精度达81.97%。光学-SAR数据与单模态数据的对比试验结果突显双模态数据的优势,进而验证了本文提出的光学-SAR场景分类数据集的重要意义。

Phase-Transition and Magnetic Moment of the Gd3＋ Ion in the Gd2Fe17 Compound

The structure and magnetic phase transitions of the Gd2Fe17 compound are investigated by using a differential thermal/thermogravimetric analyzer, x-ray diffraction, and magnetization measurements. The result shows that there are two phase structures for the Gd2Fe17 compound： the hexagonal Th2Nilr-type structure at high temperatures （above 1243℃）, and the rhombohedral Th2Zn17-type structure, respectively. A method to measure the magnetic moments of the Gd-sublattice and the Fe-sublattice in the Gd2Fe17 compound is presented. The moments of the Gd-sublattice and the Fe-sublattice in the Gd2Fe17 compound from 77 to 500 K are measured in this way with a vibrating sample magnetometer. A detailed discussion is presented.

Energy Transfer from Ce^3＋ to Eu^2＋ in LiSrBO3 and Its Potential Application in UV-LED-Based White LEDs

Ce3＋/Eu2＋ codoped LiSrBO3 phosphor is synthesized, and its luminescent characteristics are investigated. LiSrBO3：Ce3＋,Eu2＋ phosphor exhibits varied hues from blue to white and eventually to yellow by resonance-type energy transfer from Ce3＋ ion to Eu2＋ ion and tuning the relative proportion of Ce3＋/Eu2＋ properly. Energy transfer mechanism in LiSrBOa：Ce3＋, Eu2＋ phosphor is dominated by the dipole-dipole interaction, and the critical distance of the energy transfer is estimated to be about 2 nm by both spectral overlap and concentration quenching methods. Under UV radiation, white light is generated by coupling 436 and 565nm emission bands attributed to Ce3＋ and Eu2＋ radiations, respectively.

Synthesis and Properties of Magnetic Composites of Carbon Nanotubes/Fe Nanoparticle

Magnetic composites of carbon nanotubes （CNTs） are synthesized by the in situ catalytic decomposition of benzene at temperatures as low as 400℃ over Fe nanoparticles （mean grain size = 26 nm） produced by sol-gel fabrication and hydrogen reduction. The yield of CNT composite is up to about 3025% in a run of 6 h. FE- SEM and HRTEM investigations reveal that one-dimensional carbon species are produced in a large quantity. A relatively high value of magnetization is observed for the composite due to the encapsulation of ferromagnetic Fe3 C and/or α-Fe. The method is suitable for the mass-production of CNT composites that contain magnetic nanoparticles.

Integrated Optical Waveguide Sensor for Lighting Impulse Electric Field Measurement

A Lithium niobate （LiNbO3） based integrated optical E-field sensor with an optical waveguide Mach-Zehnder interferometer （MZI） and a tapered antenna has been designed and fabricated for the measurement of the pulsed electric field. The minimum detectable E-field of the sensor was 10kV/m. The sensor showed a good linear characteristic while the input E-fields varied from 10kV/m to 370kV/m. Furthermore, the maximum detectable E-field of the sensor, which could be calculated from the sensor input/output characteristic, was approximately equal to 1000kV/m. All these results suggest that such sensor can be used for the measurement of the lighting impulse electric field.

Effects of H on Electronic Structure and Ideal Tensile Strength of W： A First-Principles Calculation

We investigate the structure, energetics, and the ideal tensile strength of tungsten （W） with hydrogen （H） using a first-principles method. Both density of states （DOS） and the electron localization function （ELF） reveal the underlying physical mechanism that the tetrahedral interstitial H is the most energetically favorable. The firstprinciples computational tensile test （FPCTT） shows that the ideal tensile strength is 29.1 GPa at the strain of 14% along the [001] direction for the intrinsic W, while it decreases to 27.1 GPa at the strain of 12% when one impurity H atom is embedded into the bulk W. These results provide a useful reference to understand W as a plasma facing material in the nuclear fusion Tokamak.

Preparation and Thermal Characterization of Diamond-Like Carbon Films

Diamond-like carbon （DLC） films are prepared on silicon substrates by microwave electron cyclotron resonance plasma enhanced chemical vapor deposition. Raman spectroscopy indicates that the films have an amorphous structure and typical characteristics. The topographies of the films are presented by AFM images. Effective thermal conductivities of the films are measured using a nanosecond pulsed photothermal reflectance method. The results show that thermal conductivity is dominated by the microstructure of the films.