Optimal Configuration Method for Multi-Type Reactive Power Compensation Devices in Regional Power Grid with High Proportion of Wind Power

As the large-scale development of wind farms(WFs)progresses,the connection ofWFs to the regional power grid is evolving from the conventional receiving power grid to the sending power grid with a high proportion of wind power(WP).Due to the randomness of WP output,higher requirements are put forward for the voltage stability of each node of the regional power grid,and various reactive power compensation devices(RPCDs)need to be rationally configured to meet the stable operation requirements of the system.This paper proposes an optimal configuration method for multi-type RPCDs in regional power grids with a high proportion of WP.The RPCDs are located according to the proposed static voltage stability index(VSI)and dynamicVSI based on dynamic voltage drop area,and the optimal configuration model of RPCDs is constructed with the lowest construction cost as the objective function to determine the installed capacity of various RPCDs.Finally,the corresponding regional power grid model for intensive access to WFs is constructed on the simulation platform to verify the effectiveness of the proposed method.

Configuration optimization model of multi-energy distributed generation system

To integrate different renewable energy resources effectively in a microgrid, a configuration optimization model of a multi-energy distributed generation（DG） system and its auxiliary equipment is proposed. The model mainly consists of two parts, the determination of initial configuration schemes according to user preference and the selection of the optimal scheme. The comprehensive evaluation index（CEI）, which is acquired through the analytic hierarchy process（AHP） weight calculation method, is adopted as the evaluation criterion to rank the initial schemes. The optimal scheme is obtained according to the ranking results. The proposed model takes the diversity of different equipment parameters and investment cost into consideration and can give relatively suitable and economical suggestions for system configuration.Additionally, unlike Homer Pro, the proposed model considers the complementation of different renewable energy resources, and thus the rationality of the multi-energy DG system is improved compared with the single evaluation criterion method which only considers the total cost.

Optimization of capacity configuration and comprehensive evaluation of a renewable energy electrolysis of water for hydrogen production system

The global green hydrogen industry is experiencing rapid growth,but the high production costs are hindering its widespread adoption.To address this challenge,it is particularly important to rationally configure a renewable energy hydrogen production system.For this purpose,the study proposes a model for capacity optimization configuration of a renewable energy hydrogen production system,which integrates wind power,photovoltaic(PV)power,and concentrating solar power(CSP)with alkaline electrolyzer.It conducts capacity optimization configuration and comprehensive evaluations of the hydrogen production system across various scenarios.To minimize the total daily consumption cost,the CPLEX solver is utilized to solve the objective function and determine the capacity configuration of the renewable energy electrolysis of water hydrogen production system generator set under various scenarios.This approach achieves a utilization rate of over 99%for renewable energy.Through comprehensive evaluation,research has found that renewable energy-coupled hydrogen production significantly reduces generator capacity and electricity generation costs compared to separate hydrogen production,enhancing the economic efficiency of the system.The Wind-PV-CSP coupling hydrogen production system has the smallest generator assembly capacity and the lowest hydrogen production cost,which is 18.84 CNY·kg^(-1),significantly lower than the cost of PV-CSP coupling hydrogen production(25.78 CNY·kg^(-1))and wind-PV coupling hydrogen production(25.86 CNY·kg^(-1)).It has good development prospects and plays an important role in exploring the development path of large-scale on-site consumption of new energy.

Optimization of Wetland Plant Selection and Configuration in Urban Water Environment Ecological Restoration Projects

In urban water ecological restoration projects,the selection and configuration of wetland plants are crucial for water quality improvement,ecological diversity enhancement,and landscape beautification.Different plants have different characteristics,and a scientific and rational selection and optimization of plant species is needed.This paper proposes an optimized plant selection and configuration scheme for urban water ecological restoration based on the ecological characteristics and pollutant removal performance of wetland plants.It analyzes the diversity,removal mechanisms,and configuration modes of wetland plants,taking into account ecology,aesthetics,and cost-effectiveness,to provide scientific evidence for wetland plant configuration and support water environment management decision-making.

Optimal Static Partition Configuration in ARINC653 System

ARINC653 systems, which have been widely used in avionics industry, are an important class of safety-critical applications. Partitions are the core concept in the Arinc653 system architecture. Due to the existence of partitions, the system designer must allocate adequate time slots statically to each partition in the design phase. Although some time slot allocation policies could be borrowed from task scheduling policies, no existing literatures give an optimal allocation policy. In this paper, we present a partition configuration policy and prove that this policy is optimal in the sense that if this policy fails to configure adequate time slots to each partition, nor do other policies. Then, by simulation, we show the effects of different partition configuration policies on time slot allocation of partitions and task response time, respectively.

Optimal configuration of 5G base station energy storage considering sleep mechanism

The high-energy consumption and high construction density of 5G base stations have greatly increased the demand for backup energy storage batteries.To maximize overall benefits for the investors and operators of base station energy storage,we proposed a bi-level optimization model for the operation of the energy storage,and the planning of 5G base stations considering the sleep mechanism.A multi-base station cooperative system composed of 5G acer stations was considered as the research object,and the outer goal was to maximize the net profit over the complete life cycle of the energy storage.Furthermore,the power and capacity of the energy storage configuration were optimized.The inner goal included the sleep mechanism of the base station,and the optimization of the energy storage charging and discharging strategy,for minimizing the daily electricity expenditure of the 5G base station system.Additionally,genetic algorithm and mixed integer programming were used to solve the bi-level optimization model,analyze the numerical example test comparison of the three types of batteries and the net income of the configuration,and finally verify the validity of the model.Furthermore,the sleep mechanism,the charging and discharging strategy for energy consumption,and the economic benefits for the operators were investigated to provide reference for the 5G base station energy storage configuration.

Optimal observation configuration of UAVs based on angle and range measurements and cooperative target tracking in three-dimensional space

This article investigates the optimal observation configuration of unmanned aerial vehicles(UAVs) based on angle and range measurements, and generalizes predecessors' researches in two dimensions into three dimensions. The relative geometry of the UAVs-target will significantly affect the state estimation performance of the target, the cost function based on the Fisher information matrix(FIM) is used to derive the FIM determinant of UAVs' observation in three-dimensional space, and the optimal observation geometric configuration that maximizes the determinant of the FIM is obtained. It is shown that the optimal observation configuration of the UAVs-target is usually not unique, and the optimal observation configuration is proved for two UAVs and three UAVs in three-dimension. The long-range over-the-horizon target tracking is simulated and analyzed based on the analysis of optimal observation configuration for two UAVs. The simulation results show that the theoretical analysis and control algorithm can effectively improve the positioning accuracy of the target. It can provide a helpful reference for the design of over-the-horizon target localization based on UAVs.

Optimal Configuration Method for the Installed Capacity of the Solar-Thermal Power Stations

Because of the randomness of wind power and photovoltaic(PV)output of new energy bases,the problem of peak regulation capability and voltage stability of ultra-high voltage direct current(UHVDC)transmission lines,we proposed an optimum allocation method of installed capacity of the solar-thermal power station based on chance constrained programming in this work.Firstly,we established the uncertainty model of wind power and PV based on the chance constrained planning theory.Then we used the K-medoids clusteringmethod to cluster the scenarios considering the actual operation scenarios throughout the year.Secondly,we established the optimal configuration model based on the objective function of the strongest transient voltage stability and the lowest overall cost of operation.Finally,by quantitative analysis of actual wind power and photovoltaic new energy base,this work verified the feasibility of the proposed method.As a result of the simulations,we found that using the optimal configuration method of solar-thermal power stations could ensure an accurate allocation of installed capacity.When the installed capacity of the solar-thermal power station is 1×106 kW,the transient voltage recovery index(TVRI)is 0.359,which has a strong voltage support capacity for the system.Based on the results of this work,the optimal configuration of the installed capacity of the solar-thermal power plant can improve peak shaving performance,transient voltage support capability,and new energy consumption while satisfying the Direct Current(DC)outgoing transmission premise.

Investigation on the Optimizing Range of CombustionChamber Configuration Parameters of DSCS

Aim To obtain an optimizing range of the main configuration parameters of double swirls combustion system (DSCS) Methods To analyze the influence of DS combustion cham-ber configuration parameters on fuel spray and mixing by means of the fuel jet developmentperiphery charts obtained by the high speed photography with a modeling test device deve-loped by authors,and to examine it by the tests on a single cylinder diesel engine.Resultsand Conclusion The mixing process can be divided into four phases.The optimizing range of the ration of the inner chamber diameter to the cylinder bore,d2/D,is 0.4-0.7; and the outerchamber diameter,d1 the height of the circular ridge to the piston top face,h1,the radius of outer/inner chamber circle,R1,R2 ,the max depth of outer/inner chamber bowl,H1,H2,etc. are also important

GLOBAL OPTIMIZATION OF PUMP CONFIGURATION PROBLEM USING EXTENDED CROWDING GENETIC ALGORITHM

An extended crowding genetic algorithm (ECGA) is introduced for solvingoptimal pump configuration problem, which was presented by T. Westerlund in 1994. This problem hasbeen found to be non-convex, and the objective function contained several local optima and globaloptimality could not be ensured by all the traditional MINLP optimization method. The concepts ofspecies conserving and composite encoding are introduced to crowding genetic algorithm (CGA) formaintain the diversity of population more effectively and coping with the continuous and/or discretevariables in MINLP problem. The solution of three-levels pump configuration got from DICOPT++software (OA algorithm) is also given. By comparing with the solutions obtained from DICOPT++, ECPmethod, and MIN-MIN method, the ECGA algorithm proved to be very effective in finding the globaloptimal solution of multi-levels pump configuration via using the problem-specific information.

Configuration optimization of high velocity arc spraying gun

In order to improve the in-flight characteristics of the atomizing droplets during high velocity wire arc spraying (HVAS), some changes have been operated on the original design of the HVAS gun configuration. A comparative study was carried out to investigate the microstructure and properties of the coatings produced by the original design spraying gun and the modified one, using 3Cr13 wires of 3 mm in diameter. The characteristics of their jets were examined during spraying. The results indicate that, the included angle between the two wires and the distance from the nozzle to the meeting point of the two vires may have a strong influence on the characteristics of the in-flight droplets and then the coatings. The jet divergence is found to be lower than that of the original one (about 12° against 25°). By modified gun, the adhesion strength, the microhardness and porosity of the coating deposited by modified gun are increased by 39% and 9% respectively. And the porosity of the coatings is decreased by 57%.

Optimal operation of cold–heat–electricity multi-energy collaborative system based on price demand response

In a multi-energy collaboration system, cooling, heating, electricity, and other energy components are coupled to complement each other. Through multi-energy coordination and cooperation, they can significantly improve their individual operating efficiency and overall economic benefits. Demand response, as a multi-energy supply and demand balance method, can further improve system flexibility and economy. Therefore, a multi-energy cooperative system optimization model has been proposed, which is driven by price-based demand response to determine the impact of power-demand response on the optimal operating mode of a multi-energy cooperative system. The main components of the multi-energy collaborative system have been analyzed. The multi-energy coupling characteristics have been identified based on the energy hub model. Using market elasticity as a basis, a price-based demand response model has been built. The model has been optimized to minimize daily operating cost of the multi-energy collaborative system. Using data from an actual situation, the model has been verified, and we have shown that the adoption of price-based demand response measures can significantly improve the economy of multi-energy collaborative systems.

Cooperative Optimization of Reconfigurable Machine Tool Configurations and Production Process Plan

The production process plan design and configurations of reconfigurable machine tool （RMT） interact with each other. Reasonable process plans with suitable configurations of RMT help to improve product quality and reduce production cost. Therefore, a cooperative strategy is needed to concurrently solve the above issue. In this paper, the cooperative optimization model for RMT configurations and production process plan is presented. Its objectives take into account both impacts of process and configuration. Moreover, a novel genetic algorithm is also developed to provide optimal or near-optimal solutions： firstly, its chromosome is redesigned which is composed of three parts, operations, process plan and configurations of RMTs, respectively; secondly, its new selection, crossover and mutation operators are also developed to deal with the process constraints from operation processes （OP） graph, otherwise these operators could generate illegal solutions violating the limits; eventually the optimal configurations for RMT under optimal process plan design can be obtained. At last, a manufacturing line case is applied which is composed of three RMTs. It is shown from the case that the optimal process plan and configurations of RMT are concurrently obtained, and the production cost decreases 6.28% and nonmonetary performance increases 22%. The proposed method can figure out both RMT configurations and production process, improve production capacity, functions and equipment utilization for RMT.

GEO Satellite Thruster Configuration and Optimization

A thruster configuration and optimization method for GEO satellite is proposed in this paper.All thrusters are installed on the back panel of satellite,which is not only compatible with the design of satellite subdivision structure,but also able to provide a large installation room for the payloads and components carried by the satellite.Chemical thruster and electric thruster were selected because they have complementary advantages and can effectively reduce propellant consumption.The working mode and tasks of the thruster were analyzed in detail for thruster configuration,which was optimized in order to minimize propellant consumption.Lastly,a GEO satellite thruster was configured and optimized using this method,with results showing that the method is feasible and effective,and consequently has value for engineering applications.

Optimization of Line Configuration and Balancing for Flexible Machining Lines

Line configuration and balancing is to select the type of line and allot a given set of operations as well as machines to a sequence of workstations to realize high-efficiency production. Most of the current researches for machining line configuration and balancing problems are related to dedicated transfer lines with dedicated machine workstations. With growing trends towards great product variety and fluctuations in market demand, dedicated transfer lines are being replaced with flexible machining line composed of identical CNC machines. This paper deals with the line configuration and balancing problem for flexible machining lines. The objective is to assign operations to workstations and find the sequence of execution, specify the number of machines in each workstation while minimizing the line cycle time and total number of machines. This problem is subject to precedence, clustering, accessibility and capacity constraints among the features, operations, setups and workstations. The mathematical model and heuristic algorithm based on feature group strategy and polychromatic sets theory are presented to find an optimal solution. The feature group strategy and polychromatic sets theory are used to establish constraint model. A heuristic operations sequencing and assignment algorithm is given. An industrial case study is carried out, and multiple optimal solutions in different line configurations are obtained. The case studying results show that the solutions with shorter cycle time and higher line balancing rate demonstrate the feasibility and effectiveness of the proposed algorithm. This research proposes a heuristic line configuration and balancing algorithm based on feature group strategy and polychromatic sets theory which is able to provide better solutions while achieving an improvement in computing time.

Repairable Configuration Optimization Model under Two-Echelon Inventory

Spares inventory configuration optimization is an effective way to improve readiness and reduce life cycle cost of equipment.Through analyzing two-echelon spares support system,the METRIC model basic theory was used.An inventory configuration optimization model of two-echelon spares support system was proposed which took the spares expected shortfall as the object and made the minimum repairable parts expected shortfall instead of the maximum spares supportability as the objective function.Marginal efficiency analysis algorithm was applied to optimizing the spares configuration and generating a rational spares inventory configuration.Finally,several examples are given to verify the model.

Optimal Pitch Size of a Biphilic Surface for Boiling Heat Transfer at Subatmospheric Pressures

To date,using biphilic surfaces is one of the most promising methods for enhancing heat transfer and critical heat flux during boiling simultaneously.However,most of studies on the effect of biphilic surfaces on boiling perfor-mance have been carried out under atmospheric pressure conditions.In this context,the issues of heat transfer enhancement and stabilization of the boiling process at subatmospheric pressures are particularly critical due to the interesting characteristics of boiling heat transfer and bubble dynamics at subatmospheric pressures and their practical significance including aerospace applications.This paper investigates the effect of the pitch size between hydrophobic spots on a biphilic surface on heat transfer and bubble dynamics during boiling at subatmospheric pressures(from 11.2 kPa up to atmospheric pressure).The data analysis using infrared thermography demonstrated that the maximum heat transfer rate was achieved on a surface with a uniform pitch size(6 mm)at all pressures.In this case,the heat transfer enhancement,compared a bare surface,reached 3.4 times.An analysis of the departure diameters of bubbles based on high-speed visualization indicated that the optimal configuration of the biphilic surface corresponds to the pitch size equal to the bubble departure diameter.Using high-speed visualization also demonstrated that an early transition to film boiling was evident for configurations with a very high density of hydrophobic spots(pitch size of 2 mm).

Configuration Optimization of Cables in Ductbank Based on Their Ampacity

Electrical power companies are using more underground cables rather than overhead lines to distribute power to their customers. In practice, cables are generally installed in some compact ductbanks. Since the cost of underground cables is very expensive, using the entire space of a ductbank is extremely important. But such usage is limited due to the overheating of cables. Overheating is generally caused by overload, which means the carrying current exceeds the ampacity of a cable. The ampacity of a cable depends on not only the material and design of a cable but also the distance between different cables. Thus the configuration of cables determines the total ampacity value and the potential use of a ductbank. In this paper, the best configuration based on ampacity is achieved for a three-row, five-column ductbank that is buried at a depth of one meter below the earth’s surface. Both balanced and unbalanced scenarios are considered, and all cables have two available types to be selected.

Variable Stiffness Identification and Configuration Optimization of Industrial Robots for Machining Tasks

Industrial robots are increasingly being used in machining tasks because of their high flexibility and intelligence.However,the low structural stiffness of a robot significantly affects its positional accuracy and the machining quality of its operation equipment.Studying robot stiffness characteristics and optimization methods is an effective method of improving the stiffness performance of a robot.Accordingly,aiming at the poor accuracy of stiffness modeling caused by approximating the stiffness of each joint as a constant,a variable stiffness identification method is proposed based on space gridding.Subsequently,a task-oriented axial stiffness evaluation index is proposed to quantitatively assess the stiffness performance in the machining direction.In addition,by analyzing the redundant kinematic characteristics of the robot machining system,a configuration optimization method is further developed to maximize the index.For numerous points or trajectory-processing tasks,a configuration smoothing strategy is proposed to rapidly acquire optimized configurations.Finally,experiments on a KR500 robot were conducted to verify the feasibility and validity of the proposed stiffness identification and configuration optimization methods.

The Configuration Optimization for Multilimbed Robots with the Viewpoint of Maximum Loading Capacity

This paper presents a method for optimizing the configuration of a multilimbed robot (the robot with both arms and legs) which works with a big load. A least-effort criterion is proposed as the base of optimization. When the applying Cartesian force and the task point are given, the best configuration of the robot will be easily found through a series of imaginary motions of the robot and some simple computations. The imaginary motion varies with the working environment related to the construction of the robot, the task point and the force direction. The working environment could be predicted by the proposed inequalities, so that the way of motion could be decided in advance.