SmartMicro Grid Energy System Management Based on Optimum Running Cost for Rural Communities in Rwanda

The governmental electric utility and the private sector are joining hands to meet the target of electrifying all households by 2024.However,the aforementioned goal is challenged by households that are scattered in remote areas.So far,Solar Home Systems(SHS)have mostly been applied to increase electricity access in rural areas.SHSs have continuous constraints to meet electricity demands and cannot run income-generating activities.The current research presents the feasibility study of electrifying Remera village with the smart microgrid as a case study.The renewable energy resources available in Remera are the key sources of electricity in that village.The generation capacity is estimated based on the load profile.The microgrid configurations are simulated with HOMER,and the genetic algorithm is used to analyze the optimum cost.By analyzing the impact of operation and maintenance costs,the results show that the absence of subsidies increases the levelized cost of electricity(COE)five times greater than the electricity price from the public utility.The microgrid made up of PV,diesel generator,and batteries proved to be the most viable solution and ensured continuous power supply to customers.By considering the subsidies,COE reaches 0.186$/kWh,a competitive price with electricity from public utilities in Rwanda.

Determination of the Series Resistance of a Series Vertical-Junction Silicon (N+/P/P+) Solar Cell under Polychromatic Illumination and Magnetic Field: Effect of Optimum Thickness

By solving the magneto-transport equation for excess minority charge carriers in the base of the series vertical-junction silicon cell, the phenomenological parameters of the cell can be determined from the boundary conditions. Photocurrent density and photovoltage are determined for each value of applied magnetic field and corresponding optimum thickness, to establish the current-voltage characteristic (Jph(Sf, Sb, z, B, Hop)-Vph(Sf, Sb, z, B, Hop) of the silicon cell under polychromatic illumination. This study will make it possible to reduce the material used (by reducing the optimum thickness), which will help to lower prices. It will also enable us to reduce betting effects (lower series resistance), thereby boosting solar cell efficiency.

OPTIMUM OF PRESSURE RATIOS OF MULTI-STAGE RECIPROCATING COMPRESSOR WITH PRACTICAL INTER-COOLING

The optimum pressure ratio distribution of a multistage reciprocating compressor is presented based on the assumption, i.e. the inter stage cooling is perfect and there are no pressure losses. The optimization of the two or three stage pressure ratio is analyzed in two cases of constant heat transfer rate for the inter cooler or constant inter stage inlet temperature, based on the minimum of the sum of theoretical compression power at each stage about a multi stage reciprocating compressor. Furthermore, with an example of two stage compressor the influence on the sum of the power of each stage is analyzed when practical pressure ratio deviates from the optimum value. It is obtained that under different cooling conditions the optimum pressure ratio distribution of the multi stage compression is various, and the change of the optimum pressure ratio within a small range has little influence on the sum of the power each stage. For the two stage compression, this range can be represented as ε 1=(0 96～1 06)ε 1j .

Study on Optimum Fertilization Model of Potato Intercropped with Sugarcane

[Objective] The paper was to study the effects of different ratios of N, P and K on yield of potato intercropped with sugarcane in Lateritic red earth area of Guangxi, and seek the best N, P and K ratio for nutrition model of potato inter- cropped with sugarcane. [Method]Two field experiments adopted the optimum com- pound design （311-A） were conducted in Long＇an County of Guangxi Province in 2011 and 2012, respectively. The polynomial regression models of fertilizer applica- tion and quadratic of three factors were established by SAS statistical analysis soft- ware, and optimum nutrient simulation models of potato were obtained by computer processing. [Result] The combined application of low nitrogen and mid-high potassi- um and phosphorus fertilizer contributed to higher potato yield in experimental condi- tion. The regression model of potato yield （Yll and Y12） and dosage of N（X1）, P （X2）, K（X3） were established by using SAS statistical analysis software, in 2011 and 2012, respectively. They were Y11 =14 725.28 -415.39X1 ＋741.99X2 ＋607.83）（3-447.92X1X2- 144.09X1X3 -405.83X2X3 -267.82X1^2-795.67X2^2 -642.10X3^2, R =0.927 2; and Y12 =14 342.60 -896.25X1 ＋548.62X2 ＋925.51 X3 ＋67.81 X1X2 ＋531.60X1X3 -99.00X2X3 -904.00X1^2 - 1121.36X2^2-596.64X3^2,R=0.926 6. The regression mathematics model of potato yields preferably fit with actual situation in the locality, and have higher practical value, so it could be used for fertilizer decision and forecast. Using the computer to carry on the optimization, the N, P and K dosage of the best potato yield intercropped with sugarcane was obtained. The dosage of N, P2O5, K2O were 108.8-140.6, 172.5-204.4 and 285.9 kg/hm2, respectively. [Conclusion] The best N, P and K ratio of potato yield intercropped with sugarcane was 1：（1.23-1.68）：（2.03-2.63）.

Analysis and Optimum Design of Differential Inductors Using Distributed Capacitance Model

A distributed capacitance model for monolithic inductors is developed to predict the equivalently parasitical capacitances of the inductor.The ratio of the self-resonant frequency (f SR) of the differential-driven symmetric inductor to the f SR of the single-ended driven inductor is firstly predicted and explained.Compared with a single-ended configuration,experimental data demonstrate that the differential inductor offers a 127% greater maximum quality factor and a broader range of operating frequencies.Two differential inductors with low parasitical capacitance are developed and validated.

Is There an Optimum Age For Foreign Language Learning?

Age is one of the factors which influnce foreign language learning, but not the most important one. Comparision on the effect of foreign language learning between adults and children cannot rely merely on age. So the question of an optimum age for foreign language learning is not a simple one which is only related to age. There are different optimum ages for different aims and demands of learning foreign language.

OPTIMUM CUTTING ANALYSIS METHOD OF MEMBRANE STRUCTURE

By the optimum theory, a new cutting analytical method of the membrane structure is developed. The B-spline curve is applied to make smooth the boundary of the membrane strip. By this method, the cutting accuracy is improved. Finally, a cutting analysis example of a tension membrane structure is given.

Optimum Design of Impedance Simulator for Phased Array Antnnas

The impedance of a solid state active phased array antenna varing with frequency and beam scanning scanning angle be matched with the solid state active matching network (SSAMN). In order to adjust and measure the radar conveniently and Securely, it is necessary for the impedance of the simulator of the phased array antennas to be optimized.Having selected the PIN dilde controlling circuits and the circuit parameters optimized,the simulator circuit is determined through numerical computation The experiment is given in support of the simulation.

DYNAMICAL OPTIMUM DESIGN OF THE MECHANICAL OSCILLATION SYSTEM IN FLUIDIC GENERATOR

文中通过对射流发电机工作原理、结构特点及作用荷载的分析，建立了射流发电机机械振动系统的动力优化设计数学模型，以结构尺寸为设计变量，使结构重量极小化，满足动力位移、应力响应、基频以及尺寸限等约束条件，利用振型迭加法和复合形法求解。优化和试验结果表明：经优化后，既减轻结构重量，又显著地提高了射流发电机的输出功率。

直动从动杆圆锥凸轮机构的最佳推程、回程运动角Optimum{Φ_0,Φ′_0}及其求解方法

在推程、回程运动角之和Φ0 +Φ′0 =C(定值 )的情况下 ,必存在某一对推程、回程运动角的最佳分配Optimum {Φ0 ,Φ′0 };当选用该最佳分配时 ,直动从动杆圆锥凸轮基圆半径r0 取得其最小值r0min。在发现、揭示出上述事实的基础上 ,研究解决了当选取最佳分配Optimum{Φ0 ,Φ′0 }时 ,按许用压力角条件求解直动从动杆圆锥凸轮基圆半径最小值r0min 的解析方法。

Fuzzy Optimum Model of Semi-Structural Decision for Lectotype Optimization of Offshore Platforms

In the process of concept design of offshore platforms, it is necessary to select the best from feasible alternatives through comparison and filter. The criterion set, used to evaluate and select the satisfying alternative, consists of many qualitative and quantitative factors. Therefore, the selection is a problem of multicriteria and semi-structural decision-making. Different from traditional methods in semi-structural decision-making, a new framework and methodology is presented in this paper for evaluation of offshore platform alternatives, First, the criterion set is established for the evaluation of alternatives. Next, the approach is studied to construct the relative membership degree matrix, in which both qualitative and quantitative factors are consistent with the uniform calculating standard. And then a new weight-assessing method is developed for calculation of the weights based on the relative membership degree matrix. Finally, a multi-hierarchy fuzzy optimum model is adopted to select the satisfying offshore platform alternative. A case study shows that the new framework and methodology are scientific, reasonable and easy to use in practice.

Atlas Based Kinematic Optimum Design of the Stewart Parallel Manipulator

Optimum design is a key approach to make full use of potential advantages of a parallel manipulator. The optimum design of multi-parameter parallel manipulators（more than three design parameters）, such as Stewart manipulator, relies on analysis based and algorithm based optimum design methods, which fall to be accurate or intuitive. To solve this problem and achieve both accurate and intuition, atlas based optimum design of a general Stewart parallel manipulator is established, with rational selection of design parameters. Based on the defined spherical usable workspace（SUW）, primary kinematic performance indices of the Stewart manipulator involving workspace and condition number are introduced and analyzed. Then, corresponding performance atlases are drawn with the established non-dimensional design space, and impact of joint distribution angles on the manipulator performance is analyzed and illustrated. At last, an example on atlas based optimum design of the Stewart manipulator is accomplished to illustrate the optimum design process, considering the end-effector posture. Deduced atlases can be flexibly applied to both quantitative and qualitative analysis to get the desired optimal design for the Stewart manipulator with respect to related performance requirements. Besides, the established optimum design method can be further applied to other multi-parameter parallel manipulators.

Limit equilibrium analysis for stability of soil nailed slope and optimum design of soil nailing parameters

Reinforcement of slopes using soil nailing can effectively improve slope stability, and it has been widely used in upgrading cut slopes. Based on the assumptions of stresses on the slip surface, a new method for analyzing the stability of a slope reinforced with soil nails was established in the limit equilibrium theory framework, by considering that slope sliding occurs owing to shear failure of the slip surface, which subjects to Mohr–Coulomb(M–C) strength criterion. Meanwhile, in order to easily analyze the stability of a soil nailed slope in actual engineering and facilitate optimum design of parameters for soil nailing, factor of safety(FOS) contour curve charts were drawn on the basis of the established linear proportional relationship between the spacing of soil nails and slope height, and the length of soil nails and slope height. Then, by analyzing and verifying the results obtained from classic examples, some conclusions can be got as follows: 1) The results obtained from the current method are close to those obtained from the traditional limit equilibrium methods, and the current method can provide a strict solution for the slope FOS as it satisfies all the static equilibrium conditions of a sliding body, thus confirming the feasibility of the current method; 2) The slope FOS contour curve charts can be used not only to reliably analyze the stability of a soil nailed slope, but also to design optimally the parameters of soil nailing for the slope with a certain safety requirement.

Optimum design and layout of the cooling apparatus for long compaignship blast furnace

Generally, the cooler life can determine the blast furnace life. Theslag-metal skull frozen on the cooler can separate the cooler from the hot gas flow in blastfurnace. The key problem is how to freeze liquid slag-metal on the cooler, and the main measure isto decrease the hot surface temperature of the cooler. The computational technology of heat transferwas practically used for long campaign blast furnace design. The optimum design of the cast ironstave, copper stave, plate-stave combined system and flange stave was given by the computingresults. According to the results, the optimum arrangement of different coolers (cast iron or copperstave, flange stave and plate-stave combined system) on different height of blast furnace wall canbe found through all these temperature fields.

Optimum placement and characteristics of velocity-dependent dampers under seismic excitation

In this study, through novel drift-based equations of motion in the frequency domain, optimum placement and characteristics of linear velocity-dependent dampers are investigated. In this study, the sum of the square of the absolute values of transfer matrix elements for interstory drifts is considered as the optimization index. Optimum placement and characteristics of dampers are simultaneously obtained by minimizing the optimization index through an incremental procedure. In each step of the procedure, a predefined value is considered as the damper characteristic. The optimum story for this increment is selected such that it leads to a minimum value for the optimization index. The procedure is repeated for the next increments until the optimization index meets its target value, which is obtained according to the desired damping ratio for the overall structure. In other words, the desired overall damping ratio is the input to the proposed procedure, and the optimal placement and characteristics of the dampers are its output. It is observed that the optimal placement of a velocitydependent damper depends on the damping coefficient of the added damper, frequency of the excitation, and distribution of the mass, stiffness, and inherent damping of the main structure.

Optimum Weight Design of Functionally Graded Material Gears

Traditional gear weight optimization methods consider gear tooth number, module, face width or other dimension parameters of gear as design variables. However, due to the complicated form and geometric features peculiar to the gear, there will be large amounts of design parameters in gear design, and the influences of gear parameters changing on gear trains, transmission system and the whole equipment have to be taken into account, which increases the complexity of optimization problem. This paper puts forward to apply functionally graded materials（FGMs） to gears and then conduct the optimization. According to the force situation of gears, the material distribution form of FGM gears is determined. Then based on the performance parameters analysis of FGMs and the practical working demands for gears, a multi-objective optimization model is formed. Finally by using the goal driven optimization（GDO） method, the optimal material distribution is achieved, which makes gear weight and the maximum deformation be minimum and the maximum bending stress do not exceed the allowable stress. As an example, the applying of FGM to automotive transmission gear is conducted to illustrate the optimization design process and the result shows that under the condition of keeping the normal working performance of gear, the method achieves in greatly reducing the gear weight. This research proposes a FGM gears design method that is able to largely reduce the weight of gears by optimizing the microscopic material parameters instead of changing the macroscopic dimension parameters of gears, which reduces the complexity of gear weight optimization problem.

AN OPTIMUM VEHICULAR PATH ALGORITHM FOR TRAFFIC NETWORK BASED ON HIERARCHICAL SPATIAL REASONING

Human beings’ intellection is the characteristic of a distinct hierarchy and can be taken to construct a heuristic in the shortest path algorithms.It is detailed in this paper how to utilize the hierarchical reasoning on the basis of greedy and directional strategy to establish a spatial heuristic,so as to improve running efficiency and suitability of shortest path algorithm for traffic network.The authors divide urban traffic network into three hierarchies and set forward a new node hierarchy division rule to avoid the unreliable solution of shortest path.It is argued that the shortest path,no matter distance shortest or time shortest,is usually not the favorite of drivers in practice.Some factors difficult to expect or quantify influence the drivers’ choice greatly.It makes the drivers prefer choosing a less shortest,but more reliable or flexible path to travel on.The presented optimum path algorithm,in addition to the improvement of the running efficiency of shortest path algorithms up to several times,reduces the emergence of those factors,conforms to the intellection characteristic of human beings,and is more easily accepted by drivers.Moreover,it does not require the completeness of networks in the lowest hierarchy and the applicability and fault tolerance of the algorithm have improved.The experiment result shows the advantages of the presented algorithm.The authors argued that the algorithm has great potential application for navigation systems of large_scale traffic networks.

Optimum Design for Shrink-fit Multi-layer Vessels under Ultrahigh Pressure Using Different Materials

Multi-layer pressure vessels are widely used in every field of high pressure technology.For the purpose of enhancing a vessels＇ load bearing capacity,a beneficial process like shrink-fit is usually employed.However,few documents on optimum design for multi-layer shrink-fit vessels made of different strength materials can be found,available data are mainly on two-layer vessels.In this paper,an optimum design approach is developed for shrink-fit multi-layer vessels under ultrahigh pressure by using different materials.Maximum shear stress theory is applied as design criteria.The inner and outer radii of a multi-layer vessel,as well as the material of each layer,are assumed to be known.The optimization mathematical model is,thereby,built.Lagrange multipliers method is required to obtain the optimal design formula of wall ratio（ratio of outer to inner radii） of each layer,from which the optimum formulas of shrinkage pressure and radial interference are derived with the superposition principle employed.These formulas are applicable for the optimization design of all multi-layer vessels made of different materials,or same materials.The formulas of the limit working pressure and the contact pressure show that the optimum wall ratio of each layer and limit working pressure are only related to all selected material strength and unrelated to the position of the layer placement in the vessel.However,shrinkage pressure is related to the position of the layer placement in the vessel.Optimization design of an open ended shrink-fit three-layer vessel using different materials and comparisons proved that the optimized multi-layer vessels have outstanding characteristics of small radial interference and are easier for assembly.When the stress of each layer is distributed more evenly and appropriately,the load bearing capability and safety of vessels are enhanced.Therefore,this design is material-saving and cost-effective,and has prospect of engineering application.

Application of numerical simulation on optimum design of two-dimensional sedimentation tanks in the wastewater treatment plant

The paper establishes the relationship between the settling efficiency and the sizes of the sedimentation tank through the process of numerical simulation, which is taken as one of the constraints to set up a simple optimum designing model of sedimentation tank. The feasibility and advantages of this model based on numerical calculation are verified through the application of practical case.

Application of computer-aided engineering optimum design method in aluminum profile extrusion mould

The finite element analysis and the optimum design of aluminum profile extrusion mould were investigated using the ANSYS software and its parameterized modeling method. The optimum dimensions of the mould were obtained. It is found that the stress distribution is very uneven, and the stress convergence is rather severe in the bridge of the aluminum profile extrusion mould. The optimum height of the mould is 70.527 mm, and the optimum radius of dividing holes are 70.182 mm and 80.663 mm. Increasing the height of the mould in the range of 61.282 mm to 70.422 mm can prolong its longevity, but when the height is over 70.422 mm, its longevity reduces.