Lowering the driving voltage and improving the luminance of blue fluorescent organic light-emitting devices by thermal annealing a hole injection layer of pentacene

We chose pentacene as a hole injection layer（HIL） to fabricate the high performance blue fluorescent organic lightemitting devices（OLEDs）. We found that the carrier mobility of the pentacene thin films could be efficiently improved after a critical annealing at temperature 120℃. Then we performed the tests of scanning electron microscopy, atomic force microscopy, and Kelvin probe to explore the effect of annealing on the pentacene films. The pentacene film exhibited a more crystalline form with better continuities and smoothness after annealing. The optimal device with 120℃ annealed pentacene film and n-doped electron transport layer（ETL） presents a low turn-on voltage of 2.6 V and a highest luminance of 134800 cd/m^2 at 12 V, which are reduced by 26% and improved by 50% compared with those of the control device.

Improvement of Performance of Organic Light-Emitting Diodes with Both a MoO3 Hole Injection Layer and a MoO3 Doped Hole Transport Layer

We improve the performance of organic light-emitting diodes （OLEDs） with both a MoO3 hole injection layer （HIL） and a MoO3 doped hole transport layer （HTL）, and present a systematical and comparative investigation on these devices. Compared with OLEDs with only MoO3 HIL or MoO3 doped HTL, OLEDs with both MoO3 HIL and MoO3 doped HTL show superior performance in driving voltage, power efficiency, and stability. Based on the typical NPB/Alq3 heterojunction structure, OLEDs with both MoO3 HIL and MoO3 doped HTL show a driving voltage of 5.4 V and a power efficiency of 1.41 lm/W for 1000 cd/m2, and a lifetime of around 0. 88 h with an initial luminance of 5268 cd/m2 under a constant current of 190 mA/cm2 operation in air without encapsulation. While OLEDs with only MoO3 HIL or MoO3 doped HTL show higher driving voltages of 6.4 V or 5.8 V and lower power efficiencies of 1.201m/W or 1.341m/W for 1000cd/m2, and a shorter lifetime of 0.33 or 0.60h with an initial luminance of around 5122 or 5300cd/m2 under a constant current of 200 or 216mA/cm2 operation. Our results demonstrate clearly that using both MoO3 HIL and MoO3 doped HTL is a simple and effective approach to simultaneoasly improve both the hole injection and transport efficiency, resulting from the lowered energy barrier at the anode interface and the increased hole carrier density in MoO3 doped HTL.

Improvement of electron injection of organic light-emitting devices by inserting a thin aluminum layer into cesium carbonate injection layer

We investigate the electron injection effect of inserting a thin aluminum（Al） layer into cesium carbonate（Cs2CO3）injection layer. Two groups of organic light-emitting devices（OLEDs） are fabricated. For the first group of devices based on Alq3, we insert a thin Al layer of different thickness into Cs2CO3 injection layer, and the device＇s maximum current efficiency of 6.5 cd/A is obtained when the thickness of the thin Al layer is 0.4 nm. However, when the thickness of Al layer is 0.8 nm, the capacity of electron injection is the strongest. To validate the universality of this approach, then we fabricate another group of devices based on another blue emitting material. The maximum current efficiency of the device without and with a thin Al layer is 4.51 cd/A and 4.84 cd/A, respectively. Inserting a thin Al layer of an appropriate thickness into Cs2CO3 layer can result in the reduction of electron injection barrier, enhancement of the electron injection, and improvement of the performance of OLEDs. This can be attributed to the mechanism that thermally evaporated Cs2CO3 decomposes into cesium oxides, the thin Al layer reacts with cesium oxides to form Al–O–Cs complex, and the amount of the Al–O–Cs complex can be controlled by adjusting the thickness of the thin Al layer.

Protective Effects of Radix Astragali Injection on Multiple Organs of Rats with Obstructive Jaundice

Objective： To investigate the protective effects and mechanisms of Radix Astragali Injection on multiple organs of rats with obstructive jaundice（OJ）. Methods： A total of 180 rats were randomly divided into the sham-operated, model control and treated groups（60 in each group）. On 7, 14, 21 and 28 days after operation, the serum contents of alanine aminotransferase（ALT）, aspartate aminotransferase（AST）, r-glutamyl transpeptidase（r-GT）, total bilirubin（TBil）, direct bilirubin（DBil）, blood urine nitrogen（BUN）, and creatinine（CREA） were determined. And the pathological changes of livers, kidneys and lungs, and protein expressions of toll-like receptor-4（TLR-4） of livers, intercellular adhesion molecule-1（ICAM-1） of lungs, Bax and nuclear factor-kappa B（NF-κB）, as well as apoptotic indexes of multiple organs were observed, respectively. Results： The pathological severity scores of multiple organs（including livers on 7, 14, 21 and 28 days, kidneys on 14 and 28 days, and lungs on 14 days）, serum contents of ALT（14 and 21 days）, AST（14 days）, TBil（7, 14, 21 and 28 days）, DBil（14 and 21 days）, BUN（28 days）, protein expressions of TLR-4（in livers, 28 days）, Bax（in livers and kidneys, 21 days）, and apoptotic indexes in livers（7 and 21 days） in the treated group were significantly lower than those in the model control group（P〈0.05 or P〈0.01）. Conclusion： Radix Astragali Injection exerts protective effects on multiple organs of OJ rats by improving the pathological changes of lung, liver and kidney, decreasing the serum index of hepatic and renal function as well as inhibiting the protein expression of TLR-4 and Bax in the livers and Bax in the kidneys.