Optimal Design of High-Speed Partial Flow Pumps using Orthogonal Tests and Numerical Simulations

To investigate the influence of structural parameters on the performances and internal flow characteristics of partial flow pumps at a low specific speed of 10000 rpm,special attention was paid to the first and second stage impeller guide vanes.Moreover,the impeller blade outlet width,impeller inlet diameter,blade inclination angle,and number of blades were considered for orthogonal tests.Accordingly,nine groups of design solutions were formed,and then used as a basis for the execution of numerical simulations(CFD)aimed at obtaining the efficiency values and heads for each design solution group.The influence of impeller geometric parameters on the efficiency and head was explored,and the“weight”of each factor was obtained via a range analysis.Optimal structural parameters were finally chosen on the basis of the numerical simulation results,and the performances of the optimized model were verified accordingly(yet by means of CFD).Evidence is provided that the increase in the efficiency and head of the optimized model was 12.11%and 23.5 m,respectively,compared with those of the original model.

Life-Cycle Bearing Capacity for Pre-Stressed T-beams Based on Full-Scale Destructive Test

To investigate the evolution of load-bearing characteristics of pre-stressed beams throughout their service life and to provide a basis for accurately assessing the actual working state of damaged pre-stressed concrete T-beams,destructive tests were conducted on full-scale pre-stressed concrete beams.Based on the measurement and ana-lysis of beam deflection,strain,and crack development under various loading levels during the research tests,combined with the verification coefficient indicators specified in the codes,the verification coefficients of bridges at different stages of damage can be examined.The results indicate that the T-beams experience complete,incom-plete linear,and non-linear stages during the destructive test process.In the complete linear elastic stage,both the deflection and bottom strain verification coefficients comply with the specifications,indicating a good structural load-bearing capacity no longer adheres to the code’s requirements.In the non-linear stage,both coefficients exhi-bit a sharp increase,resulting in a further decrease in the structure’s load-bearing capacity.According to the pro-visions of the current code,the beam can be in the incomplete linear stage when both values fall within the code’s specified range.The strain verification coefficient sourced from the compression zone at the bottom of theflange is not recommended for assessing the bridge’s load-bearing capacity.

Optimization and Testing for PCR System of Rice by Orthogonal Design

[Objective] This study was to screen the economic or stable PCR system of rice and detect the generality of the selected system in different molecular markers based on PCR.[Method] With DNA extracted from rice leaves by CTAB method as the template,PCR system was optimized by L16(45)orthogonal design.[Result] Clear bands were amplified from 16 different combinations,but the amplification effects and yields had difference.The most economic and applicable system was as follows:20 ng DNA template,150 μmol/L dNT...

Influence of multiple structural parameters on interior ballistics based on orthogonal test methods

Influence of multiple structural parameters on the performance of a gun launch system driven by highpressure reactive gases is important for structural design and performance adjustment.A coupled lumped parameter model was utilized to predict the propellant combustion,and a dynamic finite element method was applied to approximate the mechanical interactions between the projectile and the barrel.The combustion and the mechanical interactions were coupled through a user subroutine interface in ABAQUS.The correctness and the capability of the finite element approximations in capturing small structural changes were validated by comparing predicted resistance with experiments.Based on the coupled model,the influence of structural parameters of a medium-caliber gun on the system performance was investigated.In order to reduce the research costs,orthogonal tests were designed to investigate the comprehensive effects of the parameters.According to statistical analysis,the important order of the structural parameters on the launching process was obtained.The results indicate that the influence of the width of the rotating band stands out among the studied parameters in the gun.The work provides a method to investigate the influence of multiple parameters on system performance and gives guidance for controlling the system performance.

Orthogonal tests of copper-clad aluminum bimetal continuous casting by nitrogen pressure core-illing

To provide theoretical basis and practical guidance for preparing composite rods by direct continuous casting, copper-clad aluminum composite rods of external copper layer diameter 12 mm and inner aluminum core diameter 8 mm were manufactured. Orthogonal tests consisted of three factors and three levels were carried out to research the effects of melting copper temperature, continuous casting speed and nitrogen pressure on the performance of composite rods. Results showed that nitrogen pressure is the most important factor in influencing the surface quality; continuous casting speed is the most important factor in influencing copper & aluminum inter diffusion amount. Nitrogen pressure can noticeably improve the surface quality and make the rods easily be drawn out, but the surface quality does not show visible improvement when the nitrogen pressure is above 0.05 MPa. Measured by tests, the compound layer can be divided into three types according to its cladding layer degree: deficient cladding, normal cladding and excess cladding. The diameter of normal copper-clad aluminum composite rods can be successfully drawn less than 0.6 mm without annealing.

SIGNIFICANCE TEST FOR EMPIRICAL ORTHOGONAL FUNCTION (EOF) ANALYSIS OF METEOROLOGICAL AND OCEANIC DATA

A Monte Carlo experiment was done to create a statistically significant test table for selecting EOF modes whose signals are above the noise level. Numerical analysis showed that it is feasible to choose a shorter data set between temporal and spatial dimensions for conducting an EOF analysis, and thus simplify calculation of the covariance matrix and solution of its eigenvalues and eigenvectors. The experiment showed that the dominant EOF modes remained the same. This approach is more computationally efficient, reducing both computing time and computer memory requirement, while still retaining the dominant signal.

Optimization of a Centrifugal Pump Used as a Turbine Impeller By Means of an Orthogonal Test Approach

A prototype centrifugal pump with a specific speed of 110 is used to investigate and optimize the performances of a turbine for power generation.Particular attention is given to the design of the internal impeller.The internal flow field is simulated in the framework of a commercial computational fluid dynamics software(ANSYS).Four geometrical parameters of the impeller are considered,i.e.,the inlet diameter,the inlet width,the blade number,and the blade angle.The optimization is carried out on the basis of a three-level approach relying on an orthogonal test method.The results of the numerical simulations show good agreement with the experimental tests under different flow conditions.In accordance with the L9(34)design table,the head and efficiency under the rated flow rate of the nine designed schemes are calculated and processed with the method of range analysis to obtain an optimized model.

Orthogonal Test About Biogas Upgrading by Pressured Water Scrubbing

Biogas is a kind of regenerable energy which is inexpensive and friendly to the environment, but the potential ofbiogas is difficult to develop fully in China, for most biogas have badly qualities and the utilization of it is monotonous. The suitable operation term about biogas upgrading by pressurized water scrubbing was researched through the orthogonal test in this study. Two sorts of scrubber packing included the random multidimensional hollow sphere packing and the structured screen packing were also used, and the effects of experiment factors included packing, water temperature, gas flow speed, water flow speed and washing pressure were studied. The results showed that better effect was got when the screen structured packing was used; all the five test factors affected the processing significantly in the arrange as before and had better and better significant effects.

Optimization of Ultrasonic Extraction Process of Oenanthe benghalensis Polysaccharide by Orthogonal Test

[Objectives] The research aimed to explore extraction method of Oenanthe benghalensis polysaccharide,and determine the optimal process of its ultrasonic extraction by orthogonal test. [Methods] Phenol-sulfuric acid method was used to determine polysaccharide's content. Based on single-factor experiment and orthogonal test,the influences of solid-liquid ratio( A),ultrasonic extraction temperature( B),ultrasonic power( C) and ultrasonic time( D) on extraction rate of O. benghalensis polysaccharide were studied,and the optimal process of ultrasonic extraction was selected. [Results] The influence order of solid-liquid ratio( A),ultrasonic extraction temperature( B),ultrasonic power( C) and ultrasonic time( D) on extraction rate of O. benghalensis polysaccharide was A > D > B > C. Via the orthogonal test,it was determined that the optimal extraction condition of O. benghalensis polysaccharide was as below: solid-liquid ratio 1∶ 25( g/mL),extraction temperature 60℃,extraction power 80 W,extraction time 40 min. Under the condition,extraction rate of O. benghalensis polysaccharide was9. 80%. [Conclusions] The process could provide the reference basis for extracting and producing O. benghalensis polysaccharides.

Optimization of Extraction Process of Prunellae Spica Compound by Orthogonal Test

[Objectives] The study aimed to optimize the extraction process of Prunellae Spica compound to provide an experimental basis for the development and utilization of the compound. [Methods]Through orthogonal test,the optimal extraction process of Prunellae Spica compound was chosen by using the yield of dry paste and ursolic acid content as evaluation indicators. [Results]The optimal extraction process of Prunellae Spica compound is as follows: solvent dosage was 16 times,and extraction frequency was 3 times,while extraction time was 1 h.[Conclusions]The extraction process of Prunellae Spica compound was stable and feasible,and this study can provide a theoretical basis for further preparation of the compound.

Study on the insecticidal activities of the extracts from four plants under orthogonal test

Aim To prepare dry powder insecticide by mixing the plant samples of Aconitum ochranthum Mey.,Aconitum hemsleyanum Pritz.and Dictamnus dasycarpus Turcz.Method The dosage ratios of the break stocks from the plants mentioned above are installed as four factors,and three levels are selected for every factor.The test is actualized according to L 9(3 4) orthogonal array.Results An optimized recipe A 3 B 3 C 3 D 1 has been obtained after considering multifarious factors such as the resources of these plants and the water-solubility of samples.Conclusion The dry powder insecticide prepared by mixing the plant samples mentioned above as 1∶1∶1mass ratio revealed that insecticidal activities for cickets,grasshopper,aphid,and 3rd instar Mythimna separata walker are significant,respectively.

Optimization of Extraction Process of Zihua Qinghuo Capsule by Orthogonal Test

With quercetin content and yield of dry extract as investigation indices, three factors, amount of water added, decoction time and decoction times were investigated by an orthogonal test, so as to select the optimal water extraction process for Zihua Qinghuo Capsule. The determined extraction process was adding 8 times of water in five herbs including Viola philippica and decocting for 2 times, 1.5 h each time. Pilot scale test demonstrated that the selected process is stable and feasible, and could provide reliable reference for practical production.

Mathematical model for abrasive suspension jet cutting based on orthogonal test design

This paper describes the application of orthogonal test design coupled with non-linear regression analysis to optimize abrasive suspension jet （AS J） cutting process and construct its cutting model. Orthogonal test design is applied to cutting stainless steel. Through range analysis on experiment results, the optimal process conditions for the cutting depth and the kerr ratio of the bottom width to the top width can be determined. In addition, the analysis of ranges and variances are all employed to identify various factors： traverse rate, working pressure, nozzle diameter, standoff distance which denote the importance order of the cutting parameters affecting cutting depth and the kerf ratio of the bottom width to the top width. ~rthermore, non-linear regression analysis is used to establish the mathematical models of the cutting parameters based on the cutting depth and the kerr ratio. Finally, the verification experiments of cutting parameters＇ effect on cutting performance, which show that optimized cutting parameters and cutting model can significantly improve the prediction of the cutting ability and quality of ASJ.

Orthogonal tests of lead-clad tin bimetal continuous casting by air pressure core-filling

To provide theoretical basis and practical guidance for preparing composite rods of external diameter no larger than 12 mm by directly continuous casting,low melting point materials of lead and tin were selected to prepare composite rods of external diameter 12 mm and inner diameter 8 mm with air pressing core filled continuous casting process.The orthogonal tests consisting of three factors and three levels were designed to investigate the parameters of melting lead temperature,continuous casting speed and air pressure that affect the performance of the composite rods.The results show that melting lead temperature is the most important factor that influences the solid/liquid interface location;continuous casting speed is the most important factor that influences the surface quality and lead and tin inter-diffusion amount;air pressure can improve the surface quality obviously and make the rods easily drawn out,but the surface quality cannot get obvious improvement when the air pressure is above 0.03 MPa.The composite rods have excellent surface quality,obvious intermediate layer,even thick clad,and metallurgical bonding interface under the condition of melting lead temperature of 375 °C,continuous casting speed of 10 mm/min,and air pressure of 0.03 MPa.

昆明烟区土壤线虫数量与环境因子的Mantel Test分析

为进一步明确昆明烟区影响线虫的环境因素,于2022年采集云南昆明烟区8个县(市、区)64个乡镇的320个植烟土壤样品,调查与测定样品采集地的海拔、土壤线虫数量以及土壤理化性质(pH值及有机质、水解性氮、速效钾和有效磷含量),并探讨土壤线虫数量与植烟土壤环境因子之间的潜在关系。结果表明,昆明烟区土壤线虫数量一定程度上受到海拔及土壤理化性质的影响,海拔与有机质、水解性氮和速效钾呈显著正相关,pH值与有效磷呈极显著负相关,相关系数为-0.850;土壤线虫数量与土壤有效磷呈正相关,与海拔、pH值、有机质、水解性氮、速效钾呈负相关,其中与海拔、有机质和水解性氮的相关系数较大,分别为-0.751、-0.651和-0.568。通过Mantel test分析确定海拔、有机质和水解性氮含量是影响昆明烟区土壤线虫数量的重要因子。本结果可为有效防治土壤线虫提供科学依据。

Failure characterization of fully grouted rock bolts under triaxial testing

Confining stresses serve as a pivotal determinant in shaping the behavior of grouted rock bolts.Nonetheless,prior investigations have oversimplified the three-dimensional stress state,primarily assuming hydrostatic stress conditions.Under these conditions,it is assumed that the intermediate principal stress(σ_(2))equals the minimum principal stress(σ_(3)).This assumption overlooks the potential variations in magnitudes of in situ stress conditions along all three directions near an underground opening where a rock bolt is installed.In this study,a series of push tests was meticulously conducted under triaxial conditions.These tests involved applying non-uniform confining stresses(σ_(2)≠σ_(3))to cubic specimens,aiming to unveil the previously overlooked influence of intermediate principal stresses on the strength properties of rock bolts.The results show that as the confining stresses increase from zero to higher levels,the pre-failure behavior changes from linear to nonlinear forms,resulting in an increase in initial stiffness from 2.08 kN/mm to 32.51 kN/mm.The load-displacement curves further illuminate distinct post-failure behavior at elevated levels of confining stresses,characterized by enhanced stiffness.Notably,the peak load capacity ranged from 27.9 kN to 46.5 kN as confining stresses advanced from σ_(2)=σ_(3)=0 to σ_(2)=20 MPa and σ_(3)=10 MPa.Additionally,the outcomes highlight an influence of confining stress on the lateral deformation of samples.Lower levels of confinement prompt overall dilation in lateral deformation,while higher confinements maintain a state of shrinkage.Furthermore,diverse failure modes have been identified,intricately tied to the arrangement of confining stresses.Lower confinements tend to induce a splitting mode of failure,whereas higher loads bring about a shift towards a pure interfacial shear-off and shear-crushed failure mechanism.

Unbound^(28)O,the heaviest oxygen isotope observed:a cutting-edge probe for testing nuclear models

The beyond-dripline oxygen isotopes^(27,28)O were recently observed at RIKEN,and were found to be unbound decaying into^(24)O by emitting neutrons.The unbound feature of the heaviest oxygen isotope,^(28)O,provides an excellent test for stateof-the-art nuclear models.The atomic nucleus is a self-organized quantum manybody system comprising specific numbers of protons Z and neutrons N.

Warm Compaction Process of P/M Steels by Orthogonal Testing Method

In order to achieve higher density of P/M steels using the die wall lubrication compacting method or powder lubricant in warm compaction process, the influence of different process parameters on the green density of warm compacted samples was studied. According to the orthogonal test method, the authors systematically study the influence of the different compaction pressure, condition of lubrication and compaction temperature on the green density of the sample in the warm compaction process, and put forward the optimal process parameter of warm compaction experiment. It is found that, a high compaction pressure （≥700 MPa）, die wall lubrication combined with a small amount of internal lubricants, and fitting compaction temperature by different condition of lubrication, are the optimal parameters in warm compaction process.

Test case generation based on orthogonal table for software black-box testing

Software testing is an important means to assure the software quality. This paper presents a practicable method to generate test cases of software testing, which is operational and high efficient. We discuss the identification of software specification categories and choices and make a classification tree. Based on the orthogonal array, it is easy to generate test cases. The number of this method is less than that of all combination of the choices.

Electrochemical biosensors for point-of-care testing

Point-of-care testing(POCT)is the practice of diagnosing and monitoring diseases where the patient is located,as opposed to traditional treatment conducted solely in a medical laboratory or other clinical setting.POCT has been less common in the recent past due to a lack of portable medical devices capable of facilitating effective medical testing.However,recent growth has occurred in this field due to advances in diagnostic technologies,device miniaturization,and progress in wearable electronics.Among these developments,electrochemical sensors have attracted interest in the POCT field due to their high sensitivity,compact size,and affordability.They are used in various applications,from disease diagnosis to health status monitoring.In this paper we explore recent advancements in electrochemical sensors,the methods of fabricating them,and the various types of sensing mechanisms that can be used.Furthermore,we delve into methods for immobilizing specific biorecognition elements,including enzymes,antibodies,and aptamers,onto electrode surfaces and how these sensors are used in real-world POCT settings.