AN IMPROVED METHOD FOR PREPARING 2—ALKOXY—5—FLUORO—3H—4—PYRIMIDONE~△

In this paper, we report an improved method for preparing 2--alkoxy 5 fluoro--3H --4--pyrimidone from 2--chloro--5--fluoro--3H--4--pyrimidone and sodium alkoxide under normal pressure at reflux temperature. Some new compounds were synthesized in higher yield by this method.

A Comparison of Weighing Methods Prior to Fusion Preparing Iron Samples for XRF Analysis

Sample preparation by fusion for XRF analysis is all about knowing the exact weights of the sample and the flux (sample-to-flux ratio). The whole analytical chain, including the weighing step in sample preparation prior to fusion, is of crucial importance to get precise and accurate x-ray fluorescence (XRF) results. Consequently, the weighing method will affect the quality of the analytical results given by the spectrometer. In this study, the effects of different weighing methods on the precision (RSD) of the obtained XRF results are compared to determine the best weighing method for sample preparation by fusion in terms of comparable precisions in the XRF results.

A Reproducible Approach of Preparing High-Quality Overdoped Bi_2Sr_2CaCu_2O_(8+δ) Single Crystals by Oxygen Annealing and Quenching Method

We report a reproducible approach in preparing high-quality overdoped Bi2 Sr2 CaCu2 08＋δ （Bi2212） single crystals by annealing Bi2212 crystals in high oxygen pressure followed by a fast quenching. In this way, high-quality overdoped and heavily overdoped Bi2212 single crystals are obtained by controlling the annealing oxygen pressure. We find that, beyond a limit of oxygen pressure that can achieve most heavily overdoped Bi2212 with a Tc N63 K, the annealed Bi2212 begins to decompose. This accounts for the existence of the hole-doping limit and thus the Tc limit in the heavily overdoped region of Bi2212 by the oxygen annealing process. These results provide a reliable way in preparing high-quality overdoped and heavily overdoped Bi2212 crystals that are important for studies of the physical properties, electronic structure and superconductivity mechanism of the cuprate superconductors.

Effect of preparation methods on the adsorption property of municipal solid waste-based carbon materials

Three different preparation methods including steam physical activation, catalytic carbonation and KOH chemical activation methods were used to prepare municipal solid waste- based carbon materials. The methylene blue （MB） adsorption value was applied to evaluate the adsorption capabilities of the prepared carbon materials. The effects of preparation methods on adsorption capability and yield of products were investigated. The yield of carbon materials with the catalytic carbonation method is the highest, and the KOH activation method is the second level. Considering the adsorption performance, the KOH activation method is much more favorable. Among the different components of municipal solid waste-based carbon materials, the adsorption properties of the single component of paperboard, the double components of tire and paperboard, the triple components of tire, paperboard and polyvinyl chloride （PVC）, and the multi-component mixtures are better than those of other single-, double-, triple- and multi-component mixtures, respectively.

Methanation of carbon dioxide on Ni/ZrO_2-Al_2O_3 catalysts:Effects of ZrO_2 promoter and preparation method of novel ZrO_2-Al_2O_3 carrier

The novel nickel-based catalysts with a nickel content of 12 wt% were prepared with the zirconia-alumina composite as the supports. The new carriers, ZrO2 improved alumina, were synthesized by three methods, i.e., impregnation-precipitation, co-precipitation, and impregnation method. The catalytic properties of these catalysts were investigated in the methanation of carbon dioxide, and the samples were characterized by X-ray diffraction （XRD）, X-ray photoelectron spectroscope （XPS）, temperature-programmed reduction （TPR） and temperature-programmed desorption （TPD） techniques. The new catalysts showed higher catalytic activity and better stability than Ni/γ-Al2O3. Furthermore, as a support for new nickel catalyst, the ZrO2-Al2O3 composite prepared by the impregnation-precipitation method was more efficient than the other supports in the methanation of carbon dioxide. The highly dispersed zirconium oxide on the surface of γ-Al2O3 inhibited the formation of nickel aluminate-like phase, which was responsible for the better dispersion of Ni species and easier reduction of NiO species, leading to the enhanced catalytic performance of corresponding catalyst.

Influence of preparation method on performance of a metal supported perovskite catalyst for combustion of methane

A different method was employed for the preparation of a metal supported perovskite catalyst for the catalytic combustion of methane.The prepared metallic catalysts were characterized by means of X-ray diffractometer(XRD),scanning electron microscopy(SEM),transmission electron microscopy(TEM),and also by ultrasonic and thermal shock tests and catalytic activity.It was found that the process factors during the preparation,e.g.the preparation of the catalyst precursor and the coating slurry,the calcination te...

Effect of preparation method on the bimetallic NiCu/SAPO-11 catalysts for the hydroisomerization of n-octane

The bimetallic NiCu/SAPO-11 catalysts were prepared by co-impregnation, sequential impregnation, coprecipitation, and mechanical mixing methods. Powder X-ray diffraction, nitrogen adsorption-desorption,temperature-programmed desorption of ammonia, transmission electron microscopy, temperatureprogrammed reduction of hydrogen, and X-ray photoelectron spectroscopy were used to characterize the physicochemical properties of the catalysts. The catalytic performance of the catalysts was assessed by the hydroisomerization of n-octane. Results indicated that the conversion of n-octane and selectivity to n-octane isomers were related to the preparation methods of the catalysts. The catalysts with Ni-Cu alloy effectively restrained the hydrogenolysis reaction that decreases the selectivity of isomerization. The catalyst prepared by the mechanical mixing of NiO and CuO hardly formed Ni-Cu alloy, showing obvious hydrogenolysis and low selectivity to n-octane isomers. The unbalance between the metal and acid sites resulted in the low conversion of n-octane and selectivity to n-octane isomers. Among all the catalysts,the catalyst prepared by the co-impregnation method exhibited high catalytic activity and selectivity to n-octane isomers.

Influence of preparation methods on CuO-CeO_2 catalysts in the preferential oxidation of CO in excess hydrogen

Influence of three different preparation methods, i.e. impregnation, coprecipitation, and inverse coprecipitation, on the preferential oxidation of CO in excess hydrogen （PROX） over CuO-CeO2 catalysts has been investigated and CuO-CeO2 catalysts are characterized using BET, XPS, XRD, UV Raman, and TPR techniques. The results show that the catalysts prepared by coprecipitation have smaller particle sizes, well-dispersed CuOx species, more oxygen vacancies, and are more active in the PROX than those prepared by the other methods. However. the inverse coprecipitation depresses the catalytic performance of CuO-CeO2 catalysts and causes the growth of CuO-CeO2 because of different pH value in the precipitation process.

Microstructures and properties of Al_2O_3 dispersion-strengthened copper alloys prepared through different methods

Al2O3 dispersion copper alloy powder was prepared by intemal oxidation, and three consolidation methods--high-velocity compaction （HVC）, hot pressing （HP）, and hot extrusion （HE）--were used to prepare Al2O3 dispersion-strengthened copper （Cu-Al2O3） alloys. The microstructures and properties of these alloys were investigated and compared. The results show that the alloys prepared by the HP and HE methods exhibited the coarsest and finest grain sizes, respectively. The alloy prepared by the HVC method exhibited the lowest relative density （98.3% vs. 99.5% for HP and 100% for HE）, which resulted in the lowest electrical conductivity （81% IACS vs. 86% IACS for HP and 87% IACS for HE）. However, this alloy also exhibited the highest hardness （77 HRB vs. 69 HRB for HP and 70 HRB for HE）, the highest compressive strength （443 MPa vs. 386 MPa for I/P and 378 MPa for HE）, and the best hardness retention among the investigated alloys. The results illustrate that the alloy prepared by the HVC method exhibits high softening temperature and good mechanical properties at high temperatures, which imply long service life when used as spot-welding electrodes.

Rapid communication Preparation of TiO_2 nanometer thin films with high photocatalytic activity by reverse micellar method

Two kinds of TiO_2 nanometer thin films were prepared on stainless steel bythe reverse micellar and sol-gel methods, respectively. The calcined TiO_ 2 thin films werecharacterized by X-ray diffraction (XRD), atomic force microscopy (AFM), BET surface area and X-rayphotoelectron spectroscopy (XPS). Photocatalytic activity was evaluated by photocatalyticdecoloration of methyl orange aqueous solution. The results showed that the TiO_2 thin filmsprepared by reverse micellar method (designated as RM-TiO_2 films) showed higher photocatalyticactivity than those by sol-gel method (designated as SG-TiO_2 films). This is attributed to the factthat the former is composed of smaller monodispersed spherical particles with a size of about 15 nmand possesses higher surface areas.

Influence of the preparation method on the catalytic activity of Mg-Al hydrotalcites as solid base catalysts

Mg-Al hydrotalcites were synthesized using different preparation methods(a co-precipitation method, a urea method, and a simple one) to analyze their effect on the catalytic activity of these solid base catalysts. The method strongly affected the structure of their layers(e.g., the growth and stacking of the layers, and the type of intercalated anions) and, accordingly, their catalytic activity. The Mg-Al hydrotalcite prepared by co-precipitation showed the best catalytic performance in the isomerization of glucose into fructose, due to the small crystallite size and sand rose morphology enhancing the exposure of surface active sites to reactants.

Effect of Preparation Methods of Bi_(2)O_(3) Nanoparticles on their Photocatalytic Activity

Bi 2O 3 nanoparticles were prepared by means of ammonia precipitation, polyol mediated methods and microemulsion chemical method. The structure and properties of the as-prepared nanoparticles, having been submitted to a heat-treatment test at 750 ℃, were characterized by means of XRD, BET, XPS and UV-Vis absorption techniques. The photocatalytic oxidation reactions of benzene, toluene and xylene were used as the model reaction to measure the photocatalytic activity of Bi 2O 3 nanoparticles, respectively. The results show that the crystallite size of Bi 2O 3 prepared with different methods and calcined at 750 ℃ were 50.6, 38.5 and 31.5 nm, respectively. The photocatalytic activity of Bi 2O 3 nanoparticles prepared with the microemulsion chemical method was higher than that of the particles prepared with the polyol mediated method; and that of the particles prepared with the micromulsion chemical method was the highest among the three. The degradation rates of the three pollutants xylene, toluene and benzene decreased in sequence.

Influence of preparation methods on the physicochemical properties and catalytic performance of MnO_x-CeO_2 catalysts for NH_3-SCR at low temperature

This work examines the influence of preparation methods on the physicochemical properties and catalytic performance of MnOx‐CeO2 catalysts for selective catalytic reduction of NO by NH3 (NH3‐SCR) at low temperature. Five different methods, namely, mechanical mixing, impregnation,hydrothermal treatment, co‐precipitation, and a sol‐gel technique, were used to synthesizeMnOx‐CeO2 catalysts. The catalysts were characterized in detail, and an NH3‐SCR model reaction waschosen to evaluate the catalytic performance. The results showed that the preparation methodsaffected the catalytic performance in the order: hydrothermal treatment > sol‐gel > co‐precipitation> impregnation > mechanical mixing. This order correlated with the surface Ce3+ and Mn4+ content,oxygen vacancies and surface adsorbed oxygen species concentration, and the amount of acidic sitesand acidic strength. This trend is related to redox interactions between MnOx and CeO2. The catalystformed by a hydrothermal treatment exhibited excellent physicochemical properties, optimal catalyticperformance, and good H2O resistance in NH3‐SCR reaction. This was attributed to incorporationof Mnn+ into the CeO2 lattice to form a uniform ceria‐based solid solution (containing Mn‐O‐Cestructures). Strengthening of the electronic interactions between MnOx and CeO2, driven by thehigh‐temperature and high‐pressure conditions during the hydrothermal treatment also improved the catalyst characteristics. Thus, the hydrothermal treatment method is an efficient and environment‐friendly route to synthesizing low‐temperature denitrification (deNOx) catalysts.

Preparation of calcium stannate by modified wet chemical method

A modified wet chemical route for low-temperature synthesis of the calcium stannate CaSnO3, a potentialmaterial for dielectric applications is reported. Firstly, a precursor CaSn(OH)6 was prepared using tin tetrachloride,calcium chloride and sodium hydroxide at room temperature. Then the precursor was annealed at relatively low tem-perature of 600 ℃ to obtain CaSnO3. The phase identification, thermal behavior and surface morphology of the sam-ples were characterized by element analysis, X-ray diffraction (XRD), thermo-gravimetric (TG) analysis and deriva-tive thermo-gravimetric (DTG) analysis, Fourier transform infrared spectroscopy (FTIR) and scanning electron mi-croscopy (SEM) in detail. The results show that CaSnO3 obtained by this method possesses a cubic perovskitestructure with average grain size of 5 μm.

Preparation of Perovskite-Type Oxides La_(1-x)Sr_xFe_(1-y)Co_yO_3 Using EDTA Sol-Gel Method

Two series of perovskite-type oxides with composition (La_(1-x))Sr_xFeO_3(x≤0.8)and La_(1-x)Sr_xFe_(1-y)Co_yO_3(x=0.2; y=0.2, 0.4)powder productions were synthesized by EDTA complexing sol-gel method. The products were characterized by XRD, TEM, SEM, BET method(N_2 adsorption)and laser granularity analysis for different synthesis conditions to obtain the optimum conditions for the preparation process. Single-phased, uniform perovskite-type oxides with small particle size were obtained by EDTA sol-gel process with high stability and repeatability, and the process temperature is much lower than that of solid state reaction method.

Preparation and optical characteristics of ZnO films by chelating sol-gel method

The effect of different annealing temperatures on the structure, morphology,and optical properties of ZnO thin films prepared by the chelating sol-gel method was investigated.Zinc-oxide thin films were coated on quartz glass substrates by dip coating. Zinc nitrate, absoluteethanol, and citric acid were used as precursor, solvent, and chelating agent, respectively. Theresults show that ZnO films derived from zinc-citrate have lower crystallization temperature (below400℃), and that the crystal structure is wurtzite. The films, treated over 500℃, consist ofnano-particles and show to be porous at 600℃. The particle size of the film increases with theincrease of the annealing temperature. The largest particle size is 60 nm at 600℃. The opticaltransmittances related to the annealing temperatures become 90% higher in the visible range. Thefilm shows a starting absorption at 380 nm, and the optical band-gap of the thin film (fired at500℃) is 3.25 eV and close to the intrinsic band-gap of ZnO (3.2 eV).

Preparation of Hadamard Gate for Open Quantum Systems by the Lyapunov Control Method

In this paper, the control laws based on the Lyapunov stability theorem are designed for a two-level open quantum system to prepare the Hadamard gate, which is an important basic gate for the quantum computers. First, the density matrix interested in quantum system is transferred to vector formation.Then, in order to obtain a controller with higher accuracy and faster convergence rate, a Lyapunov function based on the matrix logarithm function is designed. After that, a procedure for the controller design is derived based on the Lyapunov stability theorem. Finally, the numerical simulation experiments for an amplitude damping Markovian open quantum system are performed to prepare the desired quantum gate. The simulation results show that the preparation of Hadamard gate based on the proposed control laws can achieve the fidelity up to 0.9985 for the different coupling strengths.

Characterization and catalytic behavior of Na-W-Mn-Zr-S-P/SiO_2 prepared by different methods in oxidative coupling of methane

Na-W-Mn-Zr-S-P/SiO2 catalysts for oxidative coupling of methane （OCM） were prepared by incipient wetness impregnation, sol-gel and mixture slurry methods. The catalyst prepared by mixture slurry method showed the best catalytic performance among all samples. In addition, the effects of different addition sequences of Na, W, Mn, Zr, S and P on the catalytic performance were studied. The absence of Na before the addition of Mn and Zr in the catalysts preparation depressed the formation of the active phases of Mn2O3 and ZrO2 and decreased the activities of the catalysts significantly.

Effect of preparation methods on the hydrocracking performance of NiMo/Al_(2)O_(3) catalysts

In this work,NiMo catalysts with various contents of MoO_(3)were prepared through incipient wetness impregnation by a twostep method(NMxA)and onepot method(NMxB).The catalysts were then characterized by XRD,XPS,NH3TPD,H_(2)TPR,HRTEM,and N_(2)adsorptiondesorption technologies.The performance of the NiMo/Al_(2)O_(3) catalysts was investigated by hydrocracking lowtemperature coal tar.When the MoO3 content was 15 wt%,the interaction between Ni species and Al_(2)O_(3) on the NM15B catalyst was stronger than that on the NM15A catalyst,resulting in the poor performance of the former.When the MoO^(3) content was 20 wt%,MoO_(3) agglomerated on the surface of the NM20A catalyst,leading to decreased number of active sites and specific surface area and reduced catalytic performance.The increase in the number of MoS_(2) stack layers strengthened the interaction between Ni and Mo species of the NM20B catalyst and consequently improved its catalytic performance.When the MoO_(3) content reached 25 wt%,the active metals agglomerated on the surface of the NiMo catalysts,thereby directly decreasing the number of active sites.In conclusion,the twostep method is suitable for preparing catalysts with large pore diameter and low MoO_(3) content loading,and the onepot method is more appropriate for preparing catalysts with large specific surface area and high MoO_(3) content.Moreover,the NMxA catalysts had larger average pore diameter than the NMxB catalysts and exhibited improved desulfurization performance.

Preparation methods,biological activities,and potential applications of marine algae oligosaccharides:a review

Marine algae are valuable sources of health-promoting molecules that have been consumed by Asians for decades.Among aquatic flora,marine algae stand out in terms of high content of marine algae polysaccharides(MAP)such as carrageenan,alginate,fucoidan,laminaran,agarose,rhamnan,and ulvan.When hydrolyzed,MAP generate marine algae oligosaccharides(MAO),which have attracted interest in recent years due to their superior solubility compared with MAP.Besides,MAO have been demonstrated numerous biological activities including antioxidant,antidiabetic,anti-inflammatory,antimicrobial,and prebiotic activities.Thus,this review summarizes the main chemical classes of MAO,their sources,and the main processes used for their production(i.e.,physical,chemical,and biological methods),coupled with a discussion of the advantages and disadvantages of these methods.Highlights of the biological activities of MAO and their potential applications in food,nutraceutical,and pharmaceuticals would also be discussed and summarized.