The out-of-plane distortion induced in a multi-pass circumferential fillet welding of tube to pipe under different weld sequences and directions was studied using Finite Element Method(FEM) based Sysweld software and ...The out-of-plane distortion induced in a multi-pass circumferential fillet welding of tube to pipe under different weld sequences and directions was studied using Finite Element Method(FEM) based Sysweld software and verified experimentally. The FEM analyses consisted of thermal and mechanical analyses.Thermal analysis was validated with experimental transient temperature measurements. In the mechanical analysis, three different weld sequences and directions were considered to understand the mechanism of out-of-plane distortion in the tube to pipe T-joints. It was learnt that the welding direction plays a major role in minimizing the out-of-plane distortion. Further, during circumferential fillet welding of the tube to pipe component, the out-of-plane distortion generated in the x direction was primarily influenced by heat input due to the start and stop points, whereas the distortion in the z direction was influenced by time lag and welding direction. The FEM predicted distortion was compared with experimental measurements and the mechanism of out-of-plane distortion was confirmed.展开更多
Out-of-plane weak ferromagnetic(OWFM)spin arrangements with topological properties can realize a series of interesting physical properties.However,this spin structure tends to exist at low temperatures.The OWFM struct...Out-of-plane weak ferromagnetic(OWFM)spin arrangements with topological properties can realize a series of interesting physical properties.However,this spin structure tends to exist at low temperatures.The OWFM structure can also be induced at room temperature by hydrostatic pressure,whereas this isotropic approach tends to form helical AFM structures.We report the OWFM spin arrangement in single crystal Mn_(3)Sn by an anisotropic strategy of high-stressconstrained compression deformation at room temperature.Both experimental and theoretical simulation results show that the alignment of the OWFM spin structure is due to the distortion of the atomic scale caused by the strain energy during deformation.The OWFM spin arrangement can significantly change the magnetic property of Mn_(3)Sn.As a result,the remanent magnetization M_(r)for the deformed sample(0.056μ_(B)/f.u.)is about eleven times that for the pre-deformed sample(0.005μ_(B)/f.u.),and the coercivity(H_(c))increases from 0 k Oe(pre-deformed sample)to 6.02 k Oe(deformed sample).Our findings provide a way to generate the OWFM spin structure at room temperature and may give fresh ideas for creating antiferromagnetic materials with excellent physical properties.展开更多
Platinum-based alloy nanoparticles are the most attractive catalysts for the oxygen reduction reaction at present,but an in-depth understanding of the relationship between their short-range structural information and ...Platinum-based alloy nanoparticles are the most attractive catalysts for the oxygen reduction reaction at present,but an in-depth understanding of the relationship between their short-range structural information and catalytic performance is still lacking.Herein,we present a synthetic strategy that uses transition-metal oxide-assisted thermal diffusion.PtCo/C catalysts with localized tetragonal distortion were obtained by controlling the thermal diffusion process of transition-metal elements.This localized structural distortion induced a significant strain effect on the nanoparticle surface,which further shortened the length of the Pt-Pt bond,improved the electronic state of the Pt surface,and enhanced the performance of the catalyst.PtCo/C catalysts with special short-range structures achieved excellent mass activity(2.27 Amg_(Pt)^(-1))and specific activity(3.34 A cm^(-2)).In addition,the localized tetragonal distortion-induced surface compression of the Pt skin improved the stability of the catalyst.The mass activity decreased by only 13%after 30,000 cycles.Enhanced catalyst activity and excellent durability have also been demonstrated in the proton exchange membrane fuel cell configuration.This study provides valuable insights into the development of advanced Pt-based nanocatalysts and paves the way for reducing noble-metal loading and increasing the catalytic activity and catalyst stability.展开更多
We report a systematic study on layered metal SrCu_(4-x)P_(2) single crystals via transport, magnetization, thermodynamic measurements and structural characterization. We find that the crystals show large linear magne...We report a systematic study on layered metal SrCu_(4-x)P_(2) single crystals via transport, magnetization, thermodynamic measurements and structural characterization. We find that the crystals show large linear magnetoresistance without any sign of saturation with a magnetic field up to 30T. We also observe a phase transition with significant anomalies in resistivity and heat capacity at T_(p)~140 K. Thermal expansion measurement reveals a subtle lattice parameter variation near Tp, i.e.,?L_(c)/L_(c)~0.062%. The structural characterization confines that there is no structure transition below and above T_(p). All these results suggest that the nonmagnetic transition of SrCu_(4-x)P_(2) could be associated with structural distortion.展开更多
Non-penetration laser welding of lap joints in austenitic stainless steel sheets is commonly preferred in fields where the surface quality is of utmost importance.However,the application of non-penetration welded aust...Non-penetration laser welding of lap joints in austenitic stainless steel sheets is commonly preferred in fields where the surface quality is of utmost importance.However,the application of non-penetration welded austenitic stainless steel parts is limited owing to the micro bulging distortion that occurs on the back surface of the partial penetration side.In this paper,non-penetration lap laser welding experiments,were conducted on galvanized and SUS304 austenitic stainless steel plates using a fiber laser,to investigate the mechanism of bulging distortion.A comparative experiment of DC01 galvanized steel-Q235 carbon steel lap laser welding was carried out,and the deflection and distortion profile of partially penetrated side of the sheets were measured using a noncontact laser interferometer.In addition,the cold-rolled SUS304 was subjected to heat holding at different temperatures and water quenching after bending to characterize its microstructure under tensile and compressive stress.The results show that,during the heating stage of the thermal cycle of laser lap welding,the partial penetration side of the SUS304 steel sheet generates compressive stress,which extrudes the material in the heat-affected zone to the outside of the back of the SUS304 steel sheet,thereby forming a bulge.The findings of these experiments can be of great value for controlling the distortion of the partial penetrated side of austenitic stainless steel sheet during laser non-penetration lap welding.展开更多
3D elastic-plastic FE model for simulating the force controlled stretch-bending process of double-cavity aluminum profile was established using hybrid explicit−implicit solvent method.Considering the computational acc...3D elastic-plastic FE model for simulating the force controlled stretch-bending process of double-cavity aluminum profile was established using hybrid explicit−implicit solvent method.Considering the computational accuracy and efficiency,the optimal choices of numerical parameters and algorithms in FE modelling were determined.The formation mechanisms of cross-section distortion and springback were revealed.The effects of pre-stretching,post-stretching,friction,and the addition of internal fillers on forming quality were investigated.The results show that the stress state of profile in stretch-bending is uniaxial with only a circumferential stress.The stress distribution along the length direction of profile is non-uniform and the maximum tensile stress is located at a certain distance away from the center of profile.As aluminum profile is gradually attached to bending die,the distribution characteristic of cross-section distortion along the length direction of profile changes from V-shape to W-shape.After unloading the forming tools,cross-section distortion decreases obviously due to the stress relaxation,with a maximum distortion difference of 13%before and after unloading.As pre-stretching and post-stretching forces increase,cross-section distortion increases gradually,while springback first decreases and then remains unchanged.With increasing friction between bending die and profile,cross-section distortion slightly decreases,while springback increases.Cross-section distortion decreases by 83%with adding PVC fillers into the cavities of profile,while springback increases by 192.2%.展开更多
Maps, essential tools for portraying the Earth’s surface, inherently introduce distortions to geographical features. While various quantification methods exist for assessing these distortions, they often fall short w...Maps, essential tools for portraying the Earth’s surface, inherently introduce distortions to geographical features. While various quantification methods exist for assessing these distortions, they often fall short when evaluating actual geographic features. In our study, we took a novel approach by analyzing map projection distortion from a geometric perspective. We computed the fractal dimensions of different stretches of coastline before and after projection using the divide-and-conquer algorithm and image processing. Our findings revealed that map projections, even when preserving basic shapes, inevitably stretch and compress coastlines in diverse directions. This analysis method provides a more realistic and practical way to measure map-induced distortions, with significant implications for cartography, geographic information systems (GIS), and geomorphology. By bridging the gap between theoretical analysis and real-world features, this method greatly enhances accuracy and practicality when evaluating map projections.展开更多
In this paper,we define the class S_(g)^(BX)of g-parametric starlike mappings of real order γ on the unit ball BX in a complex Banach space X,where g is analytic and satisfies certain conditions.By establishing the d...In this paper,we define the class S_(g)^(BX)of g-parametric starlike mappings of real order γ on the unit ball BX in a complex Banach space X,where g is analytic and satisfies certain conditions.By establishing the distortion theorem of the Fr´echet-derivative type of S_(g)^(BX)with a weak restrictive condition,we further obtain the distortion results of the Jacobi-determinant type and the Fr´echet-derivative type for the corresponding classes(compared with S_(g)^(BX))defined on the unit polydisc(resp.unit ball with the arbitrary norm)in the space of n-dimensional complex variables,n≥2.Our results extend the classic distortion theorem of holomorphic functions from the case in one-dimensional complex space to the case in the higher dimensional complex space.The main theorems also generalize and improve some recent works.展开更多
For years,non-structural masonry walls have received little attention by code developers and professional engineers.Recently,significant efforts have been made to shed more light on out-of-plane(OOP)behavior of non-st...For years,non-structural masonry walls have received little attention by code developers and professional engineers.Recently,significant efforts have been made to shed more light on out-of-plane(OOP)behavior of non-structural masonry walls.In updated provisions of the Iranian seismic code,bed joint reinforcements(BJRs)and steel wallposts have been suggested for use.BJRs are horizontal reinforcements;steel wallposts are vertical truss-like elements intended to provide additional OOP restraints for a wall.The contribution of BJRs has previously been investigated by the authors.This study is devoted to investigating the contribution of steel wallposts to the OOP behavior of non-structural masonry walls.Using pre-validated 3D finite element(FE)models,the OOP behavior of 180 non-structural masonry walls with varying configurations and details are investigated.The OOP pressure-displacement curve,ultimate strength,the response modification factor,and the cracking pattern are among the results presented in this study.It is found that steel wallposts,especially those with higher rigidity,can improve the OOP strength of the walls.The contribution of wallposts in the case of shorter length walls and walls with an opening are more pronounced.Results also indicate that masonry walls with wallpost generally have smaller modification factors compared to similar walls without wallpost.展开更多
Electromagnetic pulse(EMP)is a kind of transient electromagnetic phenomenon with short rise time of the leading edge and wide spectrum,which usually disrupts communications and damages electronic equipment and system....Electromagnetic pulse(EMP)is a kind of transient electromagnetic phenomenon with short rise time of the leading edge and wide spectrum,which usually disrupts communications and damages electronic equipment and system.It is challenging for an EMP sensor to measure a wideband electromagnetic pulse without distortion for the whole spectrum.Therefore,analyzing the distortion of EMP measurement is crucial to evaluating the sensor distortion characteristics and correcting the measurement results.Waveform fidelity is usually employed to evaluate the distortion of an antenna.However,this metric depends on specific signal waveforms,thus is unsuitable for evaluating and analyzing the distortion of EMP sensors.In this paper,an associated-hermite-function based distortion analysis method including system transfer matrices and distortion rates is proposed,which is general and independent from individual waveforms.The system transfer matrix and distortion rate can be straightforwardly calculated by the signal orthogonal transformation coefficients using associated-hermite functions.Distortion of a sensor vs.frequency is then visualized via the system transfer matrix,which is convenient in quantitative analysis of the distortion.Measurement of a current probe,a coaxial pulse voltage probe and a B-field sensor were performed,based on which the feasibility and effectiveness of the proposed distortion analysis method is successfully verified.展开更多
Background:Studies on animals have demonstrated that maternal iron deficiency anaemia(IDA)could result in decreased cochlear sensory hair cells and reduced amplitudes of distortion-product otoacoustic emissions(DPOAEs...Background:Studies on animals have demonstrated that maternal iron deficiency anaemia(IDA)could result in decreased cochlear sensory hair cells and reduced amplitudes of distortion-product otoacoustic emissions(DPOAEs)of young guinea pigs.Thus,it is essential to study the functioning of cochlear hair cells using DPOAEs in human newborn babies with maternal IDA.The current study explores maternal IDA’s effect on DPOAEs in newborn babies.Method:A total of 110 newborn babies with gestational age≥34 weeks were considered and a‘betweensubjects’design was used.The participants were divided into 3 groups-“Normal”(61 babies without maternal IDA),“Mild”(28 babies with mild maternal IDA)and“Moderate”(21 babies with moderate maternal IDA).The cord blood was collected and the DPOAEs were recorded for each baby for a range of frequencies(1 k 8 kHz)and a range of intensities(7040 dB SPL in 10 dB steps).Results:The analysis of both DP-gram and DP input-output(I/O)function showed that there was no significant difference(p>0.05)across the normal,mild,and moderate groups in the overall presence of DPOAEs as well as the amplitude across frequencies or intensities(7040 dB SPL).Also,the overall correlation of RBC indices with DPOAE amplitude across frequencies as well as the slope of the I/O function showed no relationship.Conclusion:The current study concludes that there is no effect of late-term maternal IDA on the DPOAEs of newborn babies.展开更多
To alleviate the distortion of XRII X-ray image intensifier images in the C-arm CT computer tomography imaging system an algorithm based on the Delaunay triangulation interpolation is proposed.First the causes of the ...To alleviate the distortion of XRII X-ray image intensifier images in the C-arm CT computer tomography imaging system an algorithm based on the Delaunay triangulation interpolation is proposed.First the causes of the phenomenon the classical correction algorithms and the Delaunay triangulation interpolation are analyzed.Then the algorithm procedure is explained using flow charts and illustrations. Finally experiments are described to demonstrate its effectiveness and feasibility. Experimental results demonstrate that the Delaunay triangulation interpolation can have the following effects.In the case of the same center the root mean square distances RMSD and standard deviation STD between the corrected image with Delaunay triangulation interpolation and the ideal image are 5.760 4 ×10 -14 and 5.354 2 ×10 -14 respectively.They increase to 1.790 3 2.388 8 2.338 8 and 1.262 0 1.268 1 1.202 6 after applying the quartic polynomial model L1 and model L2 to the distorted images respectively.The RMSDs and STDs between the corrected image with the Delaunay triangulation interpolation and the ideal image are 2.489 × 10 -13 and 2.449 8 ×10 -13 when their centers do not coincide. When the quartic polynomial model L1 and model L2 are applied to the distorted images they are 1.770 3 2.388 8 2.338 8 and 1.269 9 1.268 1 1.202 6 respectively.展开更多
The segregation ratio of markers in an F2 population derived from Rudongjijiaoyaguo (Rdjjyg) and Zhongmian971 (Zm971) was studied using 3 morphological markers, 20 SSR markers, and ll SRAP markers. Totally, 24 mar...The segregation ratio of markers in an F2 population derived from Rudongjijiaoyaguo (Rdjjyg) and Zhongmian971 (Zm971) was studied using 3 morphological markers, 20 SSR markers, and ll SRAP markers. Totally, 24 markers (77.42%) showed a distorted segregation and all of them skewed toward the female genotype, which was peculiar in recent cotton research. All the three types of SSR markers and SRAP marker showed distorted segregation, but the morphological markers (Purple stem, Okra leaf, and Red spot color) were normally segregated. This indicated that such a novel segregation distortion phenomenon resulted from interior genetic factors, The allele frequency and the distribution of different genotype frequencies in the F2 population were analyzed in codominant markers, to find out factors attributed to distorted segregation. Most of them implied distorted allele frequency, but it was normal genotype frequency, which showed that these markers were influenced at the gamete level.展开更多
The slip-sweep technique is one of the high-efficiency, high-fidelity, and environmental vibroseis seismic prospecting techniques which consists of a vibrator group sweeping without waiting for the previous group's s...The slip-sweep technique is one of the high-efficiency, high-fidelity, and environmental vibroseis seismic prospecting techniques which consists of a vibrator group sweeping without waiting for the previous group's sweep to terminate. The cycle time can be reduced drastically and hence the production efficiency can be increased significantly but harmonic distortion of one sweep will leak into the record of the other sweep. In this paper, we propose an anti-correlation method for removing harmonic distortion in vibroseis data. This method is based on decomposition of the ground force signal into fundamental and harmonic components. Then the corresponding anti-correlation operator can be computed to estimate the energy of each harmonic after correlating the vibroseis data with the corresponding harmonic component. Finally, the vibroseis harmonic noise to be removed can be obtained by subtracting the extracted harmonic noise from the traces of the previous group's sweep. The advantage of the proposed method is that it can process both uncorrelated and correlated vibroseis seismic data. Moreover, the algorithm is simple, stable, and computationally fast. Especially, the significant contribution of this method is a considerable reduction in the harmonic without any alteration of the desired signals. The method was tested on both synthetic and field data sets to validate the good harmonic noise suppression results.展开更多
Using a gravity anomaly covariance function based on the second-order Ganssian Markov gravity anomaly potential model, the state equation of a gravity anomaly signal is obtained in marine gravimetry. Combined with the...Using a gravity anomaly covariance function based on the second-order Ganssian Markov gravity anomaly potential model, the state equation of a gravity anomaly signal is obtained in marine gravimetry. Combined with the system state equation and the measurement equation, a new method of the cascade Kalman filter is proposed and applied to the correction of gravity anomaly distortion. In the signal processing procedure, an inverse Kalman filter is used to restore the gravity anomaly signal and high frequency noises first. Then an adaptive Kalman filter, which uses the gravity anomaly state equation as the system equation, is set to estimate the actual gravity anomaly data. Emulations and experiments indicate that both the cascade Kalman filter method and the single inverse Kalman filter method are effective in alleviating the distortion of the gravity anomaly signal, but the performance of the cascade Kalman filter method is better than that of the single inverse Kalman filter method.展开更多
Transistors are nonlinear devices, which can produce nonlinear distortion in amplifier while amplifying signals. For weak nonlinear distortion, the expressions of total harmonic distortion (THD), the second order in...Transistors are nonlinear devices, which can produce nonlinear distortion in amplifier while amplifying signals. For weak nonlinear distortion, the expressions of total harmonic distortion (THD), the second order intermodulation distortion(IM2 ), the third order intermodulation distortion(IM 3) and intercept point(IP 3) are deduced. With the aid of software Multisim, we simulate transistor common emitter amplifier, transistor common emitter amplifier with resistor in emitter, differential amplifier and differential amplifier with resistor between emitters. The simulational results and theoretical analyses are almost the same.展开更多
According to the stationary principle of potential energy and the generalized coordinate method, a stiffness matrix of a beam element considering distortion effects is derived. Using the stiffness matrix of the beam e...According to the stationary principle of potential energy and the generalized coordinate method, a stiffness matrix of a beam element considering distortion effects is derived. Using the stiffness matrix of the beam element, a finite element program for computing thin-walled box steel beams is developed. And the program can take the section distortion and warping effects into account. The influences of diaphragm spacing on the mechanical behavior of thin-walled box beams are analyzed by the program. The numerical analysis shows that setting diaphragms have the greatest influence on the distortion normal stress, while there is very little influence on the bending normal stress. Only when the distance of adjacent diaphragms decreases to a certain value, will the distortion normal stress in the thin-walled box beam obviously reduce under the distortion load. Finally, a distortion-warping coefficient γ is introduced for simplifying the calculation of the longitudinal normal stress of thin-walled box beams. When the ratio of diaphragms adjacent space L to the maximum section dimension H is less than 2, the distortion-warping coefficient γ tends to one, which means that the distortion normal stress of the thin-walled box beam tends to zero, and the effect of the section distortion can be ignored.展开更多
Distortion analysis of SOI MOS transistor is presented.By the power series method,the distortion behaviors of FD (fully depleted) and RC (recessed channel) SOI MOS transistor configurations are investigated.It is show...Distortion analysis of SOI MOS transistor is presented.By the power series method,the distortion behaviors of FD (fully depleted) and RC (recessed channel) SOI MOS transistor configurations are investigated.It is shown that the distortion figures deteriorate with the scaling down of channel length,and the RC SOI device shows better distortion performance than the FD SOI device.At the same time,the experimental data show that the ineffective body contact can lead to an increase of the harmonic amplitude due to the bulk resistance.The presented results give an intuitive knowledge for the design of low distortion mixed signal integrated system.展开更多
An accurate circuit model of the microwave small signal characteristics of AlGaAs/GaAs HBT (heterojunction bipolar transistor) is extremely useful for microwave linear applications of the device. This paper presents ...An accurate circuit model of the microwave small signal characteristics of AlGaAs/GaAs HBT (heterojunction bipolar transistor) is extremely useful for microwave linear applications of the device. This paper presents a small signal AlGaAs/GaAs HBT equivalent circuit, based on the DC characteristics and S parameter of the device. Using Volterra series, we have calculated the third order intermodulation distortion in a linear AlGaAs/GaAs HBT amplifier. The calculations are well concordant with the measurements from two tone signals intermodulation distortion test, and its excellent third order intermodulation performance shows that AlGaAs/GaAs HBT is a very attractive candidate for linear amplification.展开更多
文摘The out-of-plane distortion induced in a multi-pass circumferential fillet welding of tube to pipe under different weld sequences and directions was studied using Finite Element Method(FEM) based Sysweld software and verified experimentally. The FEM analyses consisted of thermal and mechanical analyses.Thermal analysis was validated with experimental transient temperature measurements. In the mechanical analysis, three different weld sequences and directions were considered to understand the mechanism of out-of-plane distortion in the tube to pipe T-joints. It was learnt that the welding direction plays a major role in minimizing the out-of-plane distortion. Further, during circumferential fillet welding of the tube to pipe component, the out-of-plane distortion generated in the x direction was primarily influenced by heat input due to the start and stop points, whereas the distortion in the z direction was influenced by time lag and welding direction. The FEM predicted distortion was compared with experimental measurements and the mechanism of out-of-plane distortion was confirmed.
基金supported by the National Natural Science Foundation of China(Grant Nos.52101233 and52071279)the Hebei Natural Science Foundation(Grant No.E2022203010)+1 种基金the China Postdoctoral Science Foundation(Grant No.2022M712685)the Innovation Capability Improvement Project of Hebei Province(Grant No.22567605H)。
文摘Out-of-plane weak ferromagnetic(OWFM)spin arrangements with topological properties can realize a series of interesting physical properties.However,this spin structure tends to exist at low temperatures.The OWFM structure can also be induced at room temperature by hydrostatic pressure,whereas this isotropic approach tends to form helical AFM structures.We report the OWFM spin arrangement in single crystal Mn_(3)Sn by an anisotropic strategy of high-stressconstrained compression deformation at room temperature.Both experimental and theoretical simulation results show that the alignment of the OWFM spin structure is due to the distortion of the atomic scale caused by the strain energy during deformation.The OWFM spin arrangement can significantly change the magnetic property of Mn_(3)Sn.As a result,the remanent magnetization M_(r)for the deformed sample(0.056μ_(B)/f.u.)is about eleven times that for the pre-deformed sample(0.005μ_(B)/f.u.),and the coercivity(H_(c))increases from 0 k Oe(pre-deformed sample)to 6.02 k Oe(deformed sample).Our findings provide a way to generate the OWFM spin structure at room temperature and may give fresh ideas for creating antiferromagnetic materials with excellent physical properties.
基金supported by the National Natural Science Foundation of China (Grant No.22278123).
文摘Platinum-based alloy nanoparticles are the most attractive catalysts for the oxygen reduction reaction at present,but an in-depth understanding of the relationship between their short-range structural information and catalytic performance is still lacking.Herein,we present a synthetic strategy that uses transition-metal oxide-assisted thermal diffusion.PtCo/C catalysts with localized tetragonal distortion were obtained by controlling the thermal diffusion process of transition-metal elements.This localized structural distortion induced a significant strain effect on the nanoparticle surface,which further shortened the length of the Pt-Pt bond,improved the electronic state of the Pt surface,and enhanced the performance of the catalyst.PtCo/C catalysts with special short-range structures achieved excellent mass activity(2.27 Amg_(Pt)^(-1))and specific activity(3.34 A cm^(-2)).In addition,the localized tetragonal distortion-induced surface compression of the Pt skin improved the stability of the catalyst.The mass activity decreased by only 13%after 30,000 cycles.Enhanced catalyst activity and excellent durability have also been demonstrated in the proton exchange membrane fuel cell configuration.This study provides valuable insights into the development of advanced Pt-based nanocatalysts and paves the way for reducing noble-metal loading and increasing the catalytic activity and catalyst stability.
基金Project supported by the National Key Research and Development Program of China (Grant Nos.2023YFA1607403,2021YFA1600201,and 2022YFA1602603)the Natural Science Foundation of China (Grant Nos.U19A2093,U2032214,and U2032163)+5 种基金the Collaborative Innovation Program of Hefei Science Center,CAS (Grant No.2019HSC-CIP 001)the Youth Innovation Promotion Association of CAS (Grant No.2021117)the Natural Science Foundation of Anhui Province (No.1908085QA15)the HFIPS Director’s Fund (Grant No.YZJJQY202304)the CASHIPS Director’s Fund (Grant No.YZJJ2022QN36)supported by the High Magnetic Field Laboratory of Anhui Province。
文摘We report a systematic study on layered metal SrCu_(4-x)P_(2) single crystals via transport, magnetization, thermodynamic measurements and structural characterization. We find that the crystals show large linear magnetoresistance without any sign of saturation with a magnetic field up to 30T. We also observe a phase transition with significant anomalies in resistivity and heat capacity at T_(p)~140 K. Thermal expansion measurement reveals a subtle lattice parameter variation near Tp, i.e.,?L_(c)/L_(c)~0.062%. The structural characterization confines that there is no structure transition below and above T_(p). All these results suggest that the nonmagnetic transition of SrCu_(4-x)P_(2) could be associated with structural distortion.
文摘Non-penetration laser welding of lap joints in austenitic stainless steel sheets is commonly preferred in fields where the surface quality is of utmost importance.However,the application of non-penetration welded austenitic stainless steel parts is limited owing to the micro bulging distortion that occurs on the back surface of the partial penetration side.In this paper,non-penetration lap laser welding experiments,were conducted on galvanized and SUS304 austenitic stainless steel plates using a fiber laser,to investigate the mechanism of bulging distortion.A comparative experiment of DC01 galvanized steel-Q235 carbon steel lap laser welding was carried out,and the deflection and distortion profile of partially penetrated side of the sheets were measured using a noncontact laser interferometer.In addition,the cold-rolled SUS304 was subjected to heat holding at different temperatures and water quenching after bending to characterize its microstructure under tensile and compressive stress.The results show that,during the heating stage of the thermal cycle of laser lap welding,the partial penetration side of the SUS304 steel sheet generates compressive stress,which extrudes the material in the heat-affected zone to the outside of the back of the SUS304 steel sheet,thereby forming a bulge.The findings of these experiments can be of great value for controlling the distortion of the partial penetrated side of austenitic stainless steel sheet during laser non-penetration lap welding.
基金the National Natural Science Foundation of China(Nos.52005244,U20A20275)the Natural Science Foundation of Hunan Province,China(Nos.2021JJ30573,2023JJ60193)the Open Fund of State Key Laboratory of Advanced Design and Manufacture for Vehicle Body,China(No.31715011)。
文摘3D elastic-plastic FE model for simulating the force controlled stretch-bending process of double-cavity aluminum profile was established using hybrid explicit−implicit solvent method.Considering the computational accuracy and efficiency,the optimal choices of numerical parameters and algorithms in FE modelling were determined.The formation mechanisms of cross-section distortion and springback were revealed.The effects of pre-stretching,post-stretching,friction,and the addition of internal fillers on forming quality were investigated.The results show that the stress state of profile in stretch-bending is uniaxial with only a circumferential stress.The stress distribution along the length direction of profile is non-uniform and the maximum tensile stress is located at a certain distance away from the center of profile.As aluminum profile is gradually attached to bending die,the distribution characteristic of cross-section distortion along the length direction of profile changes from V-shape to W-shape.After unloading the forming tools,cross-section distortion decreases obviously due to the stress relaxation,with a maximum distortion difference of 13%before and after unloading.As pre-stretching and post-stretching forces increase,cross-section distortion increases gradually,while springback first decreases and then remains unchanged.With increasing friction between bending die and profile,cross-section distortion slightly decreases,while springback increases.Cross-section distortion decreases by 83%with adding PVC fillers into the cavities of profile,while springback increases by 192.2%.
文摘Maps, essential tools for portraying the Earth’s surface, inherently introduce distortions to geographical features. While various quantification methods exist for assessing these distortions, they often fall short when evaluating actual geographic features. In our study, we took a novel approach by analyzing map projection distortion from a geometric perspective. We computed the fractal dimensions of different stretches of coastline before and after projection using the divide-and-conquer algorithm and image processing. Our findings revealed that map projections, even when preserving basic shapes, inevitably stretch and compress coastlines in diverse directions. This analysis method provides a more realistic and practical way to measure map-induced distortions, with significant implications for cartography, geographic information systems (GIS), and geomorphology. By bridging the gap between theoretical analysis and real-world features, this method greatly enhances accuracy and practicality when evaluating map projections.
基金the National Natural Science Foundation of China(12071354)XIONG was the National Natural Science Foundation of China(12061035)+2 种基金the Jiangxi Provincial Natural Science Foundation(20212BAB201012)the Research Foundation of Jiangxi Provincial Department of Education(GJJ201104)the Research Foundation of Jiangxi Science and Technology Normal University(2021QNBJRC003)。
文摘In this paper,we define the class S_(g)^(BX)of g-parametric starlike mappings of real order γ on the unit ball BX in a complex Banach space X,where g is analytic and satisfies certain conditions.By establishing the distortion theorem of the Fr´echet-derivative type of S_(g)^(BX)with a weak restrictive condition,we further obtain the distortion results of the Jacobi-determinant type and the Fr´echet-derivative type for the corresponding classes(compared with S_(g)^(BX))defined on the unit polydisc(resp.unit ball with the arbitrary norm)in the space of n-dimensional complex variables,n≥2.Our results extend the classic distortion theorem of holomorphic functions from the case in one-dimensional complex space to the case in the higher dimensional complex space.The main theorems also generalize and improve some recent works.
文摘For years,non-structural masonry walls have received little attention by code developers and professional engineers.Recently,significant efforts have been made to shed more light on out-of-plane(OOP)behavior of non-structural masonry walls.In updated provisions of the Iranian seismic code,bed joint reinforcements(BJRs)and steel wallposts have been suggested for use.BJRs are horizontal reinforcements;steel wallposts are vertical truss-like elements intended to provide additional OOP restraints for a wall.The contribution of BJRs has previously been investigated by the authors.This study is devoted to investigating the contribution of steel wallposts to the OOP behavior of non-structural masonry walls.Using pre-validated 3D finite element(FE)models,the OOP behavior of 180 non-structural masonry walls with varying configurations and details are investigated.The OOP pressure-displacement curve,ultimate strength,the response modification factor,and the cracking pattern are among the results presented in this study.It is found that steel wallposts,especially those with higher rigidity,can improve the OOP strength of the walls.The contribution of wallposts in the case of shorter length walls and walls with an opening are more pronounced.Results also indicate that masonry walls with wallpost generally have smaller modification factors compared to similar walls without wallpost.
基金Research Project of High-Level Talents of Jiangsu Police Institute(No.2911118010).
文摘Electromagnetic pulse(EMP)is a kind of transient electromagnetic phenomenon with short rise time of the leading edge and wide spectrum,which usually disrupts communications and damages electronic equipment and system.It is challenging for an EMP sensor to measure a wideband electromagnetic pulse without distortion for the whole spectrum.Therefore,analyzing the distortion of EMP measurement is crucial to evaluating the sensor distortion characteristics and correcting the measurement results.Waveform fidelity is usually employed to evaluate the distortion of an antenna.However,this metric depends on specific signal waveforms,thus is unsuitable for evaluating and analyzing the distortion of EMP sensors.In this paper,an associated-hermite-function based distortion analysis method including system transfer matrices and distortion rates is proposed,which is general and independent from individual waveforms.The system transfer matrix and distortion rate can be straightforwardly calculated by the signal orthogonal transformation coefficients using associated-hermite functions.Distortion of a sensor vs.frequency is then visualized via the system transfer matrix,which is convenient in quantitative analysis of the distortion.Measurement of a current probe,a coaxial pulse voltage probe and a B-field sensor were performed,based on which the feasibility and effectiveness of the proposed distortion analysis method is successfully verified.
文摘Background:Studies on animals have demonstrated that maternal iron deficiency anaemia(IDA)could result in decreased cochlear sensory hair cells and reduced amplitudes of distortion-product otoacoustic emissions(DPOAEs)of young guinea pigs.Thus,it is essential to study the functioning of cochlear hair cells using DPOAEs in human newborn babies with maternal IDA.The current study explores maternal IDA’s effect on DPOAEs in newborn babies.Method:A total of 110 newborn babies with gestational age≥34 weeks were considered and a‘betweensubjects’design was used.The participants were divided into 3 groups-“Normal”(61 babies without maternal IDA),“Mild”(28 babies with mild maternal IDA)and“Moderate”(21 babies with moderate maternal IDA).The cord blood was collected and the DPOAEs were recorded for each baby for a range of frequencies(1 k 8 kHz)and a range of intensities(7040 dB SPL in 10 dB steps).Results:The analysis of both DP-gram and DP input-output(I/O)function showed that there was no significant difference(p>0.05)across the normal,mild,and moderate groups in the overall presence of DPOAEs as well as the amplitude across frequencies or intensities(7040 dB SPL).Also,the overall correlation of RBC indices with DPOAE amplitude across frequencies as well as the slope of the I/O function showed no relationship.Conclusion:The current study concludes that there is no effect of late-term maternal IDA on the DPOAEs of newborn babies.
基金The Natural Science Foundation of Anhui Province(No.1308085MF96)the Project of Chuzhou University(No.2012qd06,2011kj010B)+1 种基金the Scientific Research Foundation of Education Department of Anhui Province(No.KJ2014A186)the National Basic Research Program of China(973 Program)(No.2010CB732503)
文摘To alleviate the distortion of XRII X-ray image intensifier images in the C-arm CT computer tomography imaging system an algorithm based on the Delaunay triangulation interpolation is proposed.First the causes of the phenomenon the classical correction algorithms and the Delaunay triangulation interpolation are analyzed.Then the algorithm procedure is explained using flow charts and illustrations. Finally experiments are described to demonstrate its effectiveness and feasibility. Experimental results demonstrate that the Delaunay triangulation interpolation can have the following effects.In the case of the same center the root mean square distances RMSD and standard deviation STD between the corrected image with Delaunay triangulation interpolation and the ideal image are 5.760 4 ×10 -14 and 5.354 2 ×10 -14 respectively.They increase to 1.790 3 2.388 8 2.338 8 and 1.262 0 1.268 1 1.202 6 after applying the quartic polynomial model L1 and model L2 to the distorted images respectively.The RMSDs and STDs between the corrected image with the Delaunay triangulation interpolation and the ideal image are 2.489 × 10 -13 and 2.449 8 ×10 -13 when their centers do not coincide. When the quartic polynomial model L1 and model L2 are applied to the distorted images they are 1.770 3 2.388 8 2.338 8 and 1.269 9 1.268 1 1.202 6 respectively.
基金Key Project of Chinese National Programs for Fundamental Research and Development (973 Pro-gram) (No. 2004 CB117301).
文摘The segregation ratio of markers in an F2 population derived from Rudongjijiaoyaguo (Rdjjyg) and Zhongmian971 (Zm971) was studied using 3 morphological markers, 20 SSR markers, and ll SRAP markers. Totally, 24 markers (77.42%) showed a distorted segregation and all of them skewed toward the female genotype, which was peculiar in recent cotton research. All the three types of SSR markers and SRAP marker showed distorted segregation, but the morphological markers (Purple stem, Okra leaf, and Red spot color) were normally segregated. This indicated that such a novel segregation distortion phenomenon resulted from interior genetic factors, The allele frequency and the distribution of different genotype frequencies in the F2 population were analyzed in codominant markers, to find out factors attributed to distorted segregation. Most of them implied distorted allele frequency, but it was normal genotype frequency, which showed that these markers were influenced at the gamete level.
基金supported by the Sinopec Service Company and China National Petroleum Corporation
文摘The slip-sweep technique is one of the high-efficiency, high-fidelity, and environmental vibroseis seismic prospecting techniques which consists of a vibrator group sweeping without waiting for the previous group's sweep to terminate. The cycle time can be reduced drastically and hence the production efficiency can be increased significantly but harmonic distortion of one sweep will leak into the record of the other sweep. In this paper, we propose an anti-correlation method for removing harmonic distortion in vibroseis data. This method is based on decomposition of the ground force signal into fundamental and harmonic components. Then the corresponding anti-correlation operator can be computed to estimate the energy of each harmonic after correlating the vibroseis data with the corresponding harmonic component. Finally, the vibroseis harmonic noise to be removed can be obtained by subtracting the extracted harmonic noise from the traces of the previous group's sweep. The advantage of the proposed method is that it can process both uncorrelated and correlated vibroseis seismic data. Moreover, the algorithm is simple, stable, and computationally fast. Especially, the significant contribution of this method is a considerable reduction in the harmonic without any alteration of the desired signals. The method was tested on both synthetic and field data sets to validate the good harmonic noise suppression results.
基金Pre-Research Program of General Armament Departmentduring the 11th Five-Year Plan Period(No.51309010201)the National Natural Science Foundation of China(No.60575010)
文摘Using a gravity anomaly covariance function based on the second-order Ganssian Markov gravity anomaly potential model, the state equation of a gravity anomaly signal is obtained in marine gravimetry. Combined with the system state equation and the measurement equation, a new method of the cascade Kalman filter is proposed and applied to the correction of gravity anomaly distortion. In the signal processing procedure, an inverse Kalman filter is used to restore the gravity anomaly signal and high frequency noises first. Then an adaptive Kalman filter, which uses the gravity anomaly state equation as the system equation, is set to estimate the actual gravity anomaly data. Emulations and experiments indicate that both the cascade Kalman filter method and the single inverse Kalman filter method are effective in alleviating the distortion of the gravity anomaly signal, but the performance of the cascade Kalman filter method is better than that of the single inverse Kalman filter method.
文摘Transistors are nonlinear devices, which can produce nonlinear distortion in amplifier while amplifying signals. For weak nonlinear distortion, the expressions of total harmonic distortion (THD), the second order intermodulation distortion(IM2 ), the third order intermodulation distortion(IM 3) and intercept point(IP 3) are deduced. With the aid of software Multisim, we simulate transistor common emitter amplifier, transistor common emitter amplifier with resistor in emitter, differential amplifier and differential amplifier with resistor between emitters. The simulational results and theoretical analyses are almost the same.
基金Specialized Research Fund for the Doctoral Program of Higher Education (No.20070247002)
文摘According to the stationary principle of potential energy and the generalized coordinate method, a stiffness matrix of a beam element considering distortion effects is derived. Using the stiffness matrix of the beam element, a finite element program for computing thin-walled box steel beams is developed. And the program can take the section distortion and warping effects into account. The influences of diaphragm spacing on the mechanical behavior of thin-walled box beams are analyzed by the program. The numerical analysis shows that setting diaphragms have the greatest influence on the distortion normal stress, while there is very little influence on the bending normal stress. Only when the distance of adjacent diaphragms decreases to a certain value, will the distortion normal stress in the thin-walled box beam obviously reduce under the distortion load. Finally, a distortion-warping coefficient γ is introduced for simplifying the calculation of the longitudinal normal stress of thin-walled box beams. When the ratio of diaphragms adjacent space L to the maximum section dimension H is less than 2, the distortion-warping coefficient γ tends to one, which means that the distortion normal stress of the thin-walled box beam tends to zero, and the effect of the section distortion can be ignored.
文摘Distortion analysis of SOI MOS transistor is presented.By the power series method,the distortion behaviors of FD (fully depleted) and RC (recessed channel) SOI MOS transistor configurations are investigated.It is shown that the distortion figures deteriorate with the scaling down of channel length,and the RC SOI device shows better distortion performance than the FD SOI device.At the same time,the experimental data show that the ineffective body contact can lead to an increase of the harmonic amplitude due to the bulk resistance.The presented results give an intuitive knowledge for the design of low distortion mixed signal integrated system.
文摘An accurate circuit model of the microwave small signal characteristics of AlGaAs/GaAs HBT (heterojunction bipolar transistor) is extremely useful for microwave linear applications of the device. This paper presents a small signal AlGaAs/GaAs HBT equivalent circuit, based on the DC characteristics and S parameter of the device. Using Volterra series, we have calculated the third order intermodulation distortion in a linear AlGaAs/GaAs HBT amplifier. The calculations are well concordant with the measurements from two tone signals intermodulation distortion test, and its excellent third order intermodulation performance shows that AlGaAs/GaAs HBT is a very attractive candidate for linear amplification.