The nature and movement of thrusts in the eastern Iranian orogen:Sechengi Area on the northern border of Lut and Sistan

The eastern Iranian range,known as the Sistan suture zone in the past,has recently been identified as the Sistan orogen.This Paleogene orogeny is located between the Lut and Afghan microcontinents.The structural analysis shows that most of the thrusts dip towards the NW so that the Permo-Triassic sediments and Jurassic micro-diorites of the Lut Block overthrusted over the younger rocks.Structural studies show that the tectonic vergence was from the NW to the SE of the Sechengi area in the NW part of Sistan orogen.We recognized three deformation phases in eastern Iran.The first N-S deformation event(D1)resulted in the formation of tight E-W folds(F1)and associated cleavages(S1).The second E-W deformation event(D2),which occurred in the late Paleogene led to the bending of older structures,including the axial plane of the first-generation folds giving them a new northwest direction(F2).Additionally,the ramp of the first-phase thrusts(striking E-W)was reactivated,acquiring a new NNW orientation and exhibiting SSE tectonic vergence.The third deformation event(D3)resulted in the formation of NNE and WNW conjugate faults in eastern Iran.Such consecutive deformation events perpendicular to each other are inconsistent with the models of simple linear orogen presented for eastern Iran(i.e.rifting of eastern Iran continental crust and subsequence linear collision)and seem more consistent with the buckling orogeny(Orocline).

Performance investigation of a low-power Hall thruster fed on iodine propellant

The common propellants used for electric thrusters, such as xenon and krypton, are rare, expensive,and difficult to acquire. Solid iodine attracts much attention with the advantages of low cost,extensive availability, low vapor pressure, and ionization potential. The performance of a lowpower iodine-fed Hall thruster matched with a xenon-fed cathode is investigated across a broad range of operation conditions. Regulation of the iodine vapor's mass flow rates is stably achieved by using a temperature control method of the iodine reservoir. The thrust measurements are finished utilizing a thrust target during the tests. Results show that thrust and anode-specific impulse increase approximately linearly with the increasing iodine mass flow rate.At the nominal power of 200 W class, iodine mass flow rates are 0.62 and 0.93 mg/s, thrusts are7.19 and 7.58 m N, anode specific impulses are 1184 and 826 s, anode efficiencies are 20.8%and 14.5%, and thrust to power ratios are 35.9 and 37.9 m N/k W under the conditions of 250 V,0.8 A and 200 V, 1.0 A, respectively. The operating characteristics of iodine-fed Hall thruster are analyzed in different states. Further work on the measurements of plasma characteristics and experimental optimization will be carried out.

Petrogenesis and Tectonic Implications of the Early Triassic Nianzi Adakitic Granite Unit in the Yanshan Fold and Thrust Belt:New Constraints from U-Pb Geochronology and Sr-Nd-Hf Isotopes

The Nianzi granite unit,which includes the Nianzi,Xiaolianghou and Xiawopu granitic intrusions,is a significant component of the northern part of the North China Craton(NCC)and is situated in the Yanshan fold and thrust belt(YFTB).However,there is still debate regarding the tectonic evolutionary history of the YFTB during the late Permian to Triassic period,specifically regarding the timing of subduction and collision between the NCC and the Paleo-Asian Ocean.The Nianzi granite unit exhibits unique petrological,geochronological and geochemical signatures that shed light on the tectonic evolutionary history of the YFTB.This study presents detailed petrology,whole-rock geochemistry,together with Sr-Nd isotopic,zircon U-Pb dating and Lu-Hf isotopic data of the granites within the Nianzi granite unit.Our findings demonstrate that the granites primarily consist of subhedral K-feldspar,plagioclase,quartz,minor biotite and hornblende,with accessory titanite,apatite,magnetite and zircon.Zircon U-Pb dating indicates that the Xiaolianghou granite was emplaced at 247.5±0.62 Ma.Additionally,the adakitic characteristics of the Nianzi,Xiawopu and Xiaolianghou granitic intrusions,such as high Sr and Ba contents and high ratios of Sr/Y and(La/Yb)N,combined with negative Sr-Nd and Lu-Hf isotopes(87Sr/86Sr)i=0.705681–0.7057433,εNd(t)=−21.98 to−20.97,zirconεHf(t)=−20.26 to−9.92,as well as the I-type granite features of high SiO_(2),Na_(2)O and K_(2)O/Na_(2)O ratios,enriched Rb,K,Sr and Ba,along with depleted Th,U,Nb,Ta,P and Ti,suggest that the Nianzi granitic unit was mainly derived from the partial melting of a thickened lower crust containing hydrous,calc-alkaline to high-K calc-alkaline,mafic to intermediate metamorphic rocks.In light of these parameters,we further integrate our data with previous studies and conclude that the Nianzi granitic unit was generated in a post-collisional extensional environment during the Early Triassic.

Thrust Optimization of Flapping Wing via Gradient Descent Technologies

The current work aims at employing a gradient descent algorithm for optimizing the thrust of a flapping wing. An in-house solver has been employed, along with mesh movement methodologies to capture the dynamics of flow around the airfoil. An efficient framework for implementing the coupled solver and optimization in a multicore environment has been implemented for the generation of optimized solutionsmaximizing thrust performance & computational speed.

Solid Rocket Booster Thrust Asynchrony Identification Method for Solid Rocket Bundled Rockets With ESO

The role of the rocket attitude control system is to execute the required maneuvers for guidance and ensure the stability of the rocket's flight attitude. Attitude control technology has always been one of the key technologies for ensuring the success of rocket flights and has been a core topic in carrier rocket technology research. The Gravity-1 solid carrier rocket is the first solid rocket bundled rocket developed by China, adopting a configuration with four boosters and a core stage bundled together. During the actual flight process, the four booster engines are ignited first, and then, in the event of insufficient control force from the boosters, the core stage engine is ignited to participate in control. To address thrust asynchrony during the descent of the four boosters, an Extended State Observer(ESO) is employed in the control scheme for this flight segment. This involves real-time estimation and compensation of attitude parameters during flight, identification of thrust asynchrony among the boosters, and simultaneous determination of whether the core stage engine is ignited to participate in control.Through six degrees of freedom simulation analysis and Y1 flight test validation, this method has been proven to be correct and feasible.

OPTIMAL DISTRIBUTED FUSION ALGORITHM WITH ONE-STEP OUT-OF-SEQUENCE ESTIMATES

The transmission modes of multi-hop and broadcasting for Wireless Sensor Networks(WSN)often make random and unknown transmission delays appear,so multisensor data fusion based ondelayed systems attracts intense attention from lots of researchers.The existing achievements for thedelayed fusion all focus on Out-Of-Sequence Measurements(OOSM)problem which has many dis-advantages such as high communication cost,low computational efficiency,huge computational com-plexity and storage requirement,bad real-time performance and so on.In order to overcome theseproblems occurred in the OOSM fusion,the Out-Of-Sequence Estimates(OOSE)are considered tosolve the delayed fusion for the first time.Different from OOSM which belongs to the centralized fusion,the OOSE scheme transmits local estimates from local sensors to the central processor and is thus thedistributed fusion;thereby,the OOSE fusion can not only avoid the problems suffered in the OOSMfusion but also make the design of fusion algorithm highly simple and easy.Accordingly,a novel optimallinear recursive prediction weighted fusion method is proposed for one-step OOSE problem in this letter.As a tradeoff,its fusion accuracy is slightly lower than that of the OOSM method because the currentOOSM fusion is a smooth estimate and OOSE gets a prediction estimate.But,the smooth result of theOOSE problem also has good fusion accuracy.Performance analysis and computer simulation show thatthe total performance of the proposed one-step OOSE fusion algorithm is better than the current one-step OOSM fusion in the practical tracking systems.

Tracking a maneuvering target in clutter with out-of-sequence measurements for airborne radar

There are many proposed optimal or suboptimal al- gorithms to update out-of-sequence measurement（s） （OoSM（s）） for linear-Gaussian systems, but few algorithms are dedicated to track a maneuvering target in clutter by using OoSMs. In order to address the nonlinear OoSMs obtained by the airborne radar located on a moving platform from a maneuvering target in clut- ter, an interacting multiple model probabilistic data association （IMMPDA） algorithm with the OoSM is developed. To be practical, the algorithm is based on the Earth-centered Earth-fixed （ECEF） coordinate system where it considers the effect of the platform＇s attitude and the curvature of the Earth. The proposed method is validated through the Monte Carlo test compared with the perfor- mance of the standard IMMPDA algorithm ignoring the OoSM, and the conclusions show that using the OoSM can improve the track- ing performance, and the shorter the lag step is, the greater degree the performance is improved, but when the lag step is large, the performance is not improved any more by using the OoSM, which can provide some references for engineering application.

Early Cretaceous Thrust and Nappe Tectonics in North Qilian Shan,Northern Tibetan Plateau:Evidence from Field Mapping,Geochronology,and Deep Structural Analysis

The North Qilian Shan fold and thrust belt,located at the northern Tibetan Plateau and southern margin of the Hexi Corridor,is a key tectonic unit to decode the formation and expansion of the plateau.Previous studies emphasize the Cenozoic deformation due to the far-field response to the Indo-Asian collision,but the Mesozoic deformations are poorly constrained in this area.We conducted detailed field mapping,structural analysis,geochronology,and structural interpretation of deep seismic reflectional profiling and magnetotelluric(MT)sounding,to address the superposed results of the Mesozoic and Cenozoic deformation.The results recognized the North Qilian thrust and nappe system(NQTS),the root and the frontal belt are the North Qilian thrust(NQT),and the Yumu Shan klippe(YK),respectively.The middle belt is located between the NQT and the YK.Monzonitic granite zircon U-Pb dating from the middle belt yields an age of ca.415 Ma,which is similar to south NQT.The thrusting displacement is estimated at ca.48 km by structural interpretation of deep profiles.The timing is constrained in the early stage of the Early Cretaceous by the formation of simultaneous growth strata.We suggest that the NQTS has resulted from the far-field effect of the Lhasa-Qiangtang collision,and the Yumu Shan is uplifted by the superposed Cenozoic deformation.

Heterogeneity and differential hydrocarbon accumulation model of deep reservoirs in foreland thrust belts: A case study of deep Cretaceous Qingshuihe Formation clastic reservoirs in southern Junggar Basin, NW China

Using the data of drilling, logging, core, experiments and production, the heterogeneity and differential hydrocarbon accumulation model of deep reservoirs in Cretaceous Qingshuihe Formation(K1q) in the western section of the foreland thrust belt in southern Junggar Basin are investigated. The target reservoirs are characterized by superimposition of conglomerates, sandy conglomerates and sandstones, with high content of plastic clasts. The reservoir space is mainly composed of intergranular pores. The reservoirs are overall tight, and the sandy conglomerate has the best physical properties. The coupling of short deep burial period with low paleotemperature gradient and formation overpressure led to the relatively weak diagenetic strength of the reservoirs. Specifically, the sandy conglomerates show relatively low carbonate cementation, low compaction rate and high dissolution porosity. The special stress-strain mechanism of the anticline makes the reservoirs at the top of the anticline turning point more reformed by fractures than those at the limbs, and the formation overpressure makes the fractures in open state. Moreover, the sandy conglomerates have the highest oil saturation. Typical anticline reservoirs are developed in deep part of the thrust belt, but characterized by "big trap with small reservoir". Significantly, the sandy conglomerates at the top of anticline turning point have better quality, lower in-situ stress and higher structural position than those at the limbs,with the internal hydrocarbons most enriched, making them high-yield oil/gas layers. The exponential decline of fractures makes hydrocarbon accumulation difficult in the reservoirs at the limbs. Nonetheless, plane hydrocarbon distribution is more extensive at the gentle limb than the steep limb.

Winding Function Theory Based Thrust Calculation on Nested-loop Secondary Linear Machine Adapted to Linear Metro

With advantages of strong drive capability,nested-loop secondary linear machine(NLS-LM)has great potentiality in linear metro.For its secondary structure with multiple loops,it is difficult to calculate the electromagnetic thrust of NLS-LM reasonably.Hence,in this paper,one thrust calculation method is proposed considering variable loop inductance and transient loop current.Firstly,to establish the secondary winding function,the modeling domain is confined to a limited range,and the equivalent loop span is employed by analyzing the coupling relationship between primary and secondary.Then,in order to obtain the secondary flux density,the transient secondary current is solved based on the loop impedance and induced voltage.Finally,the electromagnetic thrust can be calculated reasonably by the given primary current sheet and the calculated secondary flux density.Comprehensive simulations and experiments have demonstrated the effectiveness of the proposed method.

Study of beam divergence and thrust vector eccentricity characteristics of the Hall thruster based on dual Faraday probe array planes and its applications

The accurate knowledge of the thrust vector eccentricity and beam divergence characteristics of Hall thrusters are of significant engineering value for the beneficial integration and successful application of Hall thrusters on spacecraft.For the characteristics of the plume bipolar diffusion due to the annular discharge channel of the Hall thruster,a Gaussian-fitted method for thrust vector deviation angle and beam divergence of Hall thrusters based on dual Faraday probe array planes was proposed in respect of the Hall thruster beam characteristics.The results show that the ratios of the deviation between the maximum and minimum values of the beam divergence angle and the thrust vector eccentricity angle using a Gaussian fit to the optimized Faraday probe dual plane to the mean value are 1.4%and 11.5%,respectively.The optimized thrust vector eccentricity angle obtained has been substantially improved,by approximately 20%.The beam divergence angle calculated using a Gaussian fitting to the optimized Faraday probe dual plane is approximately identical to the non-optimized one.The beam divergence and thrust vector eccentricity angles for different anode mass flow rates were obtained by averaging the beam divergence and thrust vector eccentricity angles calculated by the dual-plane,Gaussian-fitted ion current density method for different cross-sections.The study not only allows for an immediate and effective tool for determining the design of thrust vector adjustment mechanisms of spacecraft with different power Hall thrusters but also for characterizing the 3D spatial distribution of the Hall thruster plume.

Method of SLAS’s ground track manipulation based on tangential impulse thrust

Satellites with altitudes below 400 km are called super low altitude satellites(SLAS),often used to achieve responsive imaging tasks.Therefore,it is important for the manipulation of its ground track.Aiming at the problem of ground track manipulation of SLAS,a control method based on tangential impulse thrust is proposed.First,the equation of the longitude difference between SLAS and the target point on the target latitude is derived based on Gauss’s variational equations.On this basis,the influence of the tangential impulse thrust on the ground track’s longitude is derived.Finally,the method for ground track manipulation of SLAS under the tangential impulse thrust is proposed.The simulation results verify the effective-ness of the method,after manipulation,the satellite can visit the target point and revisit it for multiple days.

Integrated Sliding Mode Velocity Control of Linear Permanent Magnet Synchronous Motor with Thrust Ripple Compensation

In this paper,a compound sliding mode velocity control scheme with a new exponential reaching law(NERL)with thrust ripple observation strategy is proposed to obtain a high performance velocity loop of the linear permanent magnet synchronous motor(LPMSM)control system.A sliding mode velocity controller based on NERL is firstly discussed to restrain chattering of the conventional exponential reaching law(CERL).Furthermore,the unavoidable thrust ripple caused by the special structure of linear motor will bring about velocity fluctuation and reduced control performance.Thus,a thrust ripple compensation strategy on the basis of extend Kalman filter(EKF)theory is proposed.The estimated thrust ripple will be introduced into the sliding mode velocity controller to optimize the control accuracy and robustness.The effectiveness of the proposal is validated with experimental results.

塔里木盆地西北缘沙井子断裂带的构造特征与形成演化

塔里木盆地西北缘的沙井子断裂带,位于塔北隆起的温宿凸起和北部坳陷的阿瓦提凹陷之间。它是塔里木盆地的一条一级断裂带,由沙井子断裂、英雄断裂、温宿断裂和沙南断裂组成。其中沙井子断裂是主干断裂,其它3条是其分支断裂。本轮研究新发现温宿分支断裂,并将沙南断裂解释为英雄断裂前缘的反冲断层,归属沙井子断裂带。沙井子断裂带的雏形形成于奥陶纪末—志留纪初,在泥盆纪末—石炭纪、二叠纪末—三叠纪初、侏罗纪末—白垩纪初、白垩纪末—古近纪初和新近纪—第四纪发生过多期冲断作用和新近纪末—第四纪初的张扭性构造变形后,才最终定型。沙井子断裂带是一条断控油气富集区带,温宿油田、托探1油藏、沙南1油藏、新苏地1油气藏等都受其控制。

高超声速大动压下整流罩分离测力风洞试验

针对高超声速试验模型整体式整流罩的反推火箭拔罩分离问题,开展了反推火箭喷流模拟方法和风洞测力试验装置设计研究,试验模拟了马赫数5、动压33 kPa时整流罩反推喷流干扰效应和分离距离影响,获得了反推喷流和分离距离影响下的整流罩气动特性。试验研究表明:反推火箭拔罩分离过程中,喷流干扰作用主导了整流罩的气动特性,使得法向力系数、轴向力系数和俯仰力矩系数分别出现了44.5%、32.4%和198.6%的最大变化量;在负迎角下,整流罩压心前移显著,使得静稳定设计的整流罩呈现出静不稳定性,不利于整流罩安全分离;分离距离越大,分离距离变化对整流罩气动特性的影响越弱;将分离初始迎角限定为小的正迎角,整流罩在分离过程中容易保持姿态稳定,有利于整流罩安全分离。

基于冗余执行器的航空发动机推力快速响应控制方法研究

面向飞/推一体化控制需求,开展涡扇发动机推力快速响应控制研究,提出了适用于推力最小相位系统的冗余控制方案。研究内容包括:(1)借鉴阀位控制思想,提出在传统燃油流量(Wf)回路基础上增设尾喷口喉道面积(A8)回路,通过挖掘冗余执行器变化速率潜力,提高推力响应速度,降低了对于燃油泵快速作动的需求,同时该方法可以使喷口在推力响应过程逐渐回中,系统具备持续的推力快速调节能力;(2)分析了A8调节推力的物理机理,指出容腔压力动力学主导的部件间流量匹配过程使得A8对推力具有直馈作用,是提高推力响应速度的有效途径。基于发动机部件级模型的评估结果表明,本文提出的方法在执行机构存在速率限制的情况下,实现了推力10 rad/s闭环带宽和A8回中的设计目标,方法可行、有效。在推力响应过程中,A8直馈作用对推力变化的贡献度最高时超过50%。随着对于推力控制模式和推力响应速度的日趋关注,应对容腔内的压力动态过程给予充分的重视。

冀北崇礼-赤城地区逆冲推覆构造特征及地热勘探前景

【研究目的】本文对崇礼—赤城地区隆起山地型带状热储进行了总结,对类似勘探区的地热调查工作具有一定的借鉴作用,可为后续地热资源勘探提供新的依据。【研究方法】通过野外地质调查与详细构造填图,结合可控源音频大地电磁测深(CSAMT)探测结果,分析了崇礼-赤城地区的逆冲推覆构造特征与地热勘探前景。【研究结果】崇礼-赤城地区发育了多种样式的逆冲断层,逆冲断层主要表现为从北向南的逆冲运动方向,在主底板逆冲断层的作用下,太古界、中元古界、白垩系自老向新依次推覆,形成了具有典型逆冲推覆构造分带分层现象。CSAMT剖面测量与解释的初步结果,验证了崇礼-赤城地区发育的逆冲推覆构造,逆冲岩席中发育多条叠瓦式逆冲断层,其断层面向北倾斜,倾角大于60°,向深部汇聚于主底板逆冲断层。【结论】逆冲推覆构造之上发现的中元古界长城系白云岩、白云质大理岩,扩展了该地区地热勘探前景。

基于比例谐振内模扩张状态观测器的PMLSM推力波动抑制策略

定位力是永磁同步直线电机(PMLSM)产生推力波动的主要原因,导致振动和噪声,恶化驱动系统运行性能。针对这一问题,该文提出一种基于比例谐振内模扩张状态观测器(PR-IMESO)的PMLSM推力波动抑制策略以提高系统控制精度和运行性能。首先,对PMLSM推力波动进行建模与分析,针对推力波动中占比较大的定位力分量,根据内模原理研究考虑定位力模型的内模扩张状态观测器(IMESO),并在观测器中引入谐振项以加强对二次脉动定位力的抑制。所提出抑制策略对PMLSM定位力具有良好的观测及补偿能力,还可对其余未建模的复杂动子推力波动进行抑制,具有较好的推力波动整体抑制效果。最后,在一台750 W的PMLSM实验平台上验证所提出抑制策略的有效性。

基于偏航机动的常推力定点着陆制导方法

实现定点着陆终端位置速度六分量控制通常需要发动机推力可调。提出了一种通过偏航机动实现固定推力下的定点着陆制导方法。该方法通过偏转航向角,调节发动机输出在下降轨迹平面内的分量,从而实现航程控制;为了消除推力方向偏转产生的横向位置、速度偏差,设计了偏转角符号调整策略,使得着陆器在水平面内呈“之”字形运动,以一定推进剂为代价,最终保证了下降着陆终端位置、速度的全部可控。仿真表明,所提方法简单有效,易于工程实施。

可倾瓦推力轴承惰转过程的最小膜厚预测方法

为建立可倾瓦推力轴承惰转过程中最小油膜厚度的预测方法,依据核主泵推力轴承的实际工作情况,基于雷诺方程的自编程序,分别进行热态和冷态下主、副轴瓦润滑性能参数的计算与数值模拟分析,提出可倾瓦推力轴承的最小油膜厚度的理论拟合公式,并对最小膜厚的计算值和拟合值进行对比和分析。结果表明:随着转速降低,主轴瓦的最小膜厚单调减小,副轴瓦的最小膜厚先增加后减小;主、副轴瓦最小膜厚的计算值可以和拟合值较好地对应,验证了理论拟合公式的可靠性。提出的理论拟合公式可以通过额定转速下的最小膜厚计算结果预测多种工作条件下的最小油膜厚度,为主泵惰转的安全性提供重要参考。