CFD modeling of gas−liquid flow phenomenon in lead smelting oxygen-enriched side-blown furnace

A validated numerical model was established to simulate gas−liquid flow behaviors in the oxygen-enriched side-blown bath furnace.This model included the slip velocity between phases and the gas thermal expansion effect.Its modeling results were verified with theoretical correlations and experiments,and the nozzle-eroded states in practice were also involved in the analysis.Through comparison,it is confirmed that the thermal expansion effect influences the flow pattern significantly,which may lead to the backward motion of airflow and create a potential risk to production safety.Consequently,the influences of air injection velocity and furnace width on airflow behavior were investigated to provide operating and design guidance.It is found that the thin layer melt,which avoids high-rate oxygen airflow eroding nozzles,shrinks as the injection velocity increases,but safety can be guaranteed when the velocity ranges from 175 to 275 m/s.Moreover,the isoline patterns and heights of thin layers change slightly when the furnace width increases from 2.2 to 2.8 m,indicating that the furnace width shows a limited influence on production safety.

Resource utilization of hazardous gypsum sludge in oxidation smelting of lead concentrate

Gypsum sludge,a hazardous waste generated by the non-ferrous smelting industry,presents a significant challenge for disposal and utilization.To investigate the feasibility of substituting gypsum sludge for limestone as a flux for smelting,the effects of calcium sulfate(CaSO_(4))and smelting conditions on oxygen-rich smelting of lead concentrate were studied.The interaction between CaSO_(4)and sulfides facilitates the conversion of CaSO_(4)into CaO,which is crucial for slag formation.The order of the influence of sulfide minerals on the conversion of CaSO_(4)is pyrite>sphalerite>galena.When using gypsum sludge exclusively as the calcium source,under optimal conditions with a CaO/SiO_(2)mass ratio of 0.8,an FeO/SiO_(2)mass ratio of 1.2,a melting temperature of 1150℃,an oxygen flow rate of 1.3 L/min,the recovery rates of Pb and Zn in the lead-rich slag reached 85.01%and 95.69%,respectively,with a sulfur content of 2.65 wt%.The As content in the smelting slag obtained by reduction smelting was 0.02 wt%.Resource utilization of gypsum sludge in lead smelting is a feasible method.

Numerical investigation of sinusoidal pulsating gas intake to intensify the gas-slag momentum transfer in the top-blown smelting furnace

The variation characteristics of bubble morphology and the thermal-physical properties of bubble boundary in the top-blown smelting furnace were explored by means of the computational fluid dynamics method.The essential aspects of the fluid phase(e.g.,splashing volume,dead zone of copper slag,and gas penetration depth)were explored together with the effect of sinusoidal pulsating gas intake on the momentum-transfer performance between phases.The results illustrated that two relatively larger vortices and two smaller vortices appear in the bubble waist and below the lance,respectively.The expansion of larger ones as well as the shrinking of smaller ones combine to cause the contraction of the bubble waist.Compared to the results of the case with a fixed gas injection velocity(V_(g)=58 m/s),the splashing volume and dead zone volume of the slag under the V_(g)=58+10sin(2πt)condition are reduced by 24.9%and 23.5%,respectively,where t represents the instant time.Gas penetration depth and slag motion velocity of the latter are 1.03 and 1.31 times high-er than those of the former,respectively.

Microstructure control and hot cracking behavior of the new Ni-Co based superalloy prepared by electron beam smelting layered solidification technology

The prevention of hot cracking formation is of utmost importance in the production of the new Ni-Co based superalloys through the utilization of the electron beam smelting layered solidification technique(EBSL),as it ensures exceptional homogeneity and dependable consistency of the specimens.In contrast to previous studies that focused on minimizing the liquid film and solidification range,our methodology adopts a distinct approach.In this research,a novel methodology was employed to mitigate internal stresses through the implementation of equiaxed grain layers via an alternately reduced cooling method.This ultimately resulted in the elimination of hot cracking.To be more specific,the transition from a columnar to an equiaxed structure was observed during the layer-by-layer construction process in the fabrication of the new Ni-Co based superalloy in EBSL.The EBSL-Ni-Co superalloy,when subjected to the alternating reduction cooling method,exhibited an internal stress of 49 MPa.This value represents a significant reduction of 83.8%compared to the internal stress observed when employing the linear reduction cooling method.Additionally,the solvus temperature of theγ-γ’eutectic phases in EBSL-Ni-Co superalloys produced by the alternating reduction cooling method is significantly higher.Intriguingly,the Nth layer of the EBSL-Ni-Co based superalloys produced by EBSL simultaneously heats treated with the preceding layers.And the low melting point phase gradually dissolved back into the matrix.The implementation of an alternating reduced cooling method successfully mitigated the formation of the liquid film in theγ-γ’eutectic phase and the buildup of internal stresses in the EBSL-Ni-Co superalloy during its manufacturing process.These discoveries open up a novel preparation procedure pathway for the manufacture of crack-free superalloys with superior mechanical characteristics using EBSL.

Separation of halogens and recovery of heavy metals from secondary copper smelting dust

The separation of halogens and recovery of heavy metals from secondary copper smelting(SCS)dust using a sulfating roasting−water leaching process were investigated.The thermodynamic analysis results confirm the feasibility of the phase transformation to metal sulfates and to gaseous HF and HCl.Under the sulfating roasting conditions of the roasting temperature of 250℃ and the sulfuric acid excess coefficient of 1.8,over 74 wt.%of F and 98 wt.%of Cl were volatilized into flue gas.Approximately 98.6 wt.%of Zn and 96.5 wt.%of Cu in the roasting product were dissolved into the leaching solution after the water leaching process,while the leaching efficiencies of Pb and Sn were only 0.12%and 0.22%,respectively.The mechanism studies indicate the pivotal effect of roasting temperature on the sulphation reactions from various metal species to metal sulfates and the salting out reactions from various metal halides to gaseous hydrogen halides.

Rapid detection and risk assessment of soil contamination at lead smelting site based on machine learning

A general prediction model for seven heavy metals was established using the heavy metal contents of 207soil samples measured by a portable X-ray fluorescence spectrometer(XRF)and six environmental factors as model correction coefficients.The eXtreme Gradient Boosting(XGBoost)model was used to fit the relationship between the content of heavy metals and environment characteristics to evaluate the soil ecological risk of the smelting site.The results demonstrated that the generalized prediction model developed for Pb,Cd,and As was highly accurate with fitted coefficients(R~2)values of 0.911,0.950,and 0.835,respectively.Topsoil presented the highest ecological risk,and there existed high potential ecological risk at some positions with different depths due to high mobility of Cd.Generally,the application of machine learning significantly increased the accuracy of pXRF measurements,and identified key environmental factors.The adapted potential ecological risk assessment emphasized the need to focus on Pb,Cd,and As in future site remediation efforts.

Effect of Fe/SiO2 and CaO/SiO2 mass ratios on metal recovery rate and metal content in slag in oxygen-enriched direct smelting of jamesonite concentrate

The oxygen-enriched direct smelting of jamesonite concentrate was carried out at 1250℃by changing the slag composition.The effects of Fe/SiO2 and Ca O/SiO2 mass ratios on the metal recovery rate as well as metal content in slag were investigated.Experimental results indicated that the metal(Pb+Sb)recovery rate was up to 88.30%,and metal(Pb+Sb)content in slag was below 1 wt.%under the condition of slag composition of 21-22 wt.%Fe,19-20 wt.%SiO2 and 17-18 wt.%Ca O with Fe/SiO2 mass ratio of 1.1:1 and Ca O/SiO2 mass ratio of 0.9:1.The microanalysis of the alloy and slag demonstrated that the main phases in the alloy contained metallic Pb,metallic Sb and a small amount of Cu2 Sb and Fe Sb2 intermetallic compounds.The slag was mainly composed of kirschsteinite and fayalite.Zinc in the raw material was mainly oxidized into the slag phase in the form of zinc oxide.

Mixture of ilmenite and high phosphorus iron ore smelted by oxygen-enriched top-blown smelting reduction

In order to reasonably utilize the abundant resources of high-phosphorus iron ore and ilmenite in China, the technology of top-blown smelting reduction with oxygen enrichment was used to smelt the mixed ore of high-phosphorus iron and ilmenite. The effect, which is related to basicity, reduction temperature, carbon-oxygen ratio and time of ventilated oxygen to iron recovery, dephosphorization rate, content of iron, phosphorus, sulfur and titanium in pig iron, was investigated in the experiment. The results show that an ideal outcome can be gained in condition of 6：4 ration on Mengqiao concentrate and Huimin iron ore, temperature of 1 500℃, basicity of 1.3, 1.0 on molar ration of carbon to oxygen, time of 10 min on blowing-oxygen. The outcome is that there is no foamy slag in generation, a good separation of slag and iron, iron recovery with 91.41%, content of phosphorus with 0.27% and tilanium content less than 0.001%, The atmosphere of strong oxidizing in the upper of reduction container and high potential of oxygen in the composition of slag in this technique bring phosphorus, titanium and silicon into slag, which ensures less content of impurity in pig iron.

Clean production of Fe-based amorphous soft magnetic alloys via smelting reduction of high-phosphorus iron ore and apatite

Separated preparation of prealloys and amorphous alloys results in severe solidification-remelting and beneficial element removal-readdition contradictions,which markedly increase energy consumption and emissions.This study offered a novel strategy for the direct production of FePC amorphous soft magnetic alloys via smelting reduction of high-phosphorus iron ore(HPIO)and apatite.First,the thermodynamic conditions and equilibrium states of the carbothermal reduction reactions in HPIO were calculated,and the element content in reduced alloys was theoretically determined.The phase and structural evolutions,as well as element migration and enrichment behaviors during the smelting reduction of HPIO and Ca_(3)(PO_(4))_(2),were then experimentally verified.The addition of Ca_(3)(PO_(4))_(2)in HPIO contributes to the enrichment of the P element in reduced alloys and the subsequent development of Fe_(3)P and Fe_(2)P phases.The content of P and C elements in the range of 1.52 wt% -14.63 wt% and 0.62 wt% -2.47 wt%,respectively,can be well tailored by adding 0-50 g Ca_(3)(PO_(4))_(2)and controlling the C/O mole ratio of 0.8-1.1,which is highly consistent with the calculated results.These FePC alloys were then successfully formed into amorphous ribbons and rods.The energy consumption of the proposed strategy was estimated to be 2.00×10^(8) kJ/t,which is reduced by 30% when compared with the conventional production process.These results are critical for the comprehensive utilization of mineral resources and pave the way for the clean production of Fe-based amorphous soft magnetic alloys.

The new green smelting process of CNREG commissioned

A demonstration project of the major scientific and technological project in Inner Mongolia Autonomous Region-"Industrialization Test of New Green Smelting Technology for Rare Earth Concentrate produced from Baiyun Obo ore"was commissioned on November 20th.This project adopts the"new green smelting process for rare earth concentrate"independently developed by China Northern Rare Earth Group(CNREG),and has achieved a new breakthrough in rare earth smelting technology.

钒钛矿PLCsmelt工艺冶炼技术

钒钛磁铁矿的成分和结构复杂,是世界公认的难选冶矿种。与普通铁精矿相比,钒钛磁铁矿的品位偏低,有价组元分散于各矿相中,采矿和选冶都具有较大的难度,钒钛矿资源的有效利用是钢铁行业的关注问题之一。基于此,依据攀西钒钛磁铁矿特性,提出了PLCsmelt炼铁新工艺。首先介绍了PLCsmelt炼铁工艺流程,以气基竖炉-电炉工艺为参照,从工艺流程、成本、资源利用率、碳排放和能耗等方面对两种工艺进行了分析对比,并与高炉工艺进行了碳排放及能耗对比。研究表明,PLCsmelt的工艺成本、钒资源回收率、碳排放及能耗分别为1943.1元/t、75.9%、1009.6 kgCO_(2)/tHM及370.9 kgce/tHM,各参数较高炉及气基竖炉-电炉工艺均有明显优势,证明PLCsmelt炼铁新工艺更有利于钒钛磁铁矿资源综合高效利用。同时对PLCsmelt工艺技术的发展前景进行了展望,也对该技术存在的问题及未来研究的方向进行了讨论。

Recovery of valuable metals from spent lithium ion batteries by smelting reduction process based on FeO-SiO_2-Al_2O_3 slag system

NA novel smelting reduction process based on FeO-SiO2-Al2O3 slag system for spent lithium ion batteries with Al cans was developed, while using copper slag as the only slag former. The feasibility of the process and the mechanism of copper loss in slag were investigated. 98.83% Co, 98.39% Ni and 93.57% Cu were recovered under the optimum conditions of slag former/battery mass ratio of 4.0：1, smelting temperature of 1723 K, and smelting mass ratio of time of 30 min. The FeO-SiO2-Al2O3 slag system for the smelting process is appropriate under the conditions of m（FeO）：m（SiO2）=0.58：1？1.03：1, and 17.19%？21.52% Al2O3 content. The obtained alloy was mainly composed of Fe-Co-Cu-Ni solid solution including small amounts of matte. The obtained slag mainly consisted of fayalite and hercynite. Meanwhile, the mechanism of copper loss is the mechanical entrainment from strip-like fayalite particles in the main form of copper sulfide and metallic copper.

Soil vanadium pollution and microbial response characteristics from stone coal smelting district

A field investigation was performed to study the content, speciation and mobility of vanadium, as well as microbial response in soil from a stone coal smelting district in Hunan province of China. The results showed that the contents of soil V ranged from 168 to 1538 mg/kg, which exceeded the maximum permissible value of Canadian soil quality for V. The mean soil V content from wasteland area reached 1421 mg/kg, and those from the areas related with slag heap, ore pile and smelting center were 380, 260 and 225 mg/kg, respectively. Based on the results of the modified BCR sequential extraction procedure, V contents in the mobile fractions varied from 19.2 to 637 mg/kg accounting for 7.4%-42.3% of total V, and those of V(+5) species were between 21.9 and 534.0 mg/kg. Soil enzyme activity and microbial basal respiration were adversely affected by high level of soil V. More attention should be paid to soil V pollution and potential hazardous surrounding the stone coal smelting district.

Recovery of cobalt from converter slag of Chambishi Copper Smelter using reduction smelting process

The reduction smelting process for cobalt recovery from converter slag of the Chambishi Copper Smelter in Zambia was studied. The effects of reducing agent dosage, smelting temperature and time and the addition of slag modifiers （CaO and TiO2） were investigated. In addition, the depleted slag and cobalt-bearing alloy were characterized by X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy. Under the determined conditions, 94.02% Co, 95.76% Cu and less than 18% Fe in the converter slag were recovered. It was found that the main phases of depleted slag were fayalite and hercynite; and the cobalt-bearing alloy mainly contained metallic copper, Fe-Co-Cu alloys and a small amount of sulfide.

Thermodynamic modeling of antimony removal from complex resources in copper smelting process

This work investigated the reaction mechanism of Sb in copper smelting process. The difference of multi-phase distribution of Sb in four typical copper smelting processes was analyzed. A multi-phase equilibrium model of the oxygen-enriched bottom-blow copper smelting process was developed. The impacts of Cu, S, and Sb concentrations in raw materials on Sb distribution in multiphases were researched. This model was also used to investigate the effect of process factors such as copper matte grade, oxygen-enriched concentration, smelting temperature, and oxygen/ore ratio(ratio of oxygen flow rate under standard conditions to concentrate charge rate) on Sb distribution behavior. The results showed that calculation data were in good agreement with the actual production results and literature data. Increasing the Cu content and decreasing the S and Sb contents in the concentrate, increasing the copper matte grade, oxygen/enriched concentration, and oxygen-ore ratio, and at the same time appropriately reducing the smelting temperature are conducive to the targeted enrichment of Sb into the slag. Modeling results can provide theoretical guidance for the clean and efficient treatment of complex resources and the comprehensive recycling of associated elements.

Furnace structure analysis for copper flash continuous smelting based on numerical simulation

According to the innate characteristic of four types of furnace, the copper flash continuous smelting （CFCS） furnace can be considered a synthetic reactor of two relatively independent processes： flash matte smelting process （FMSP） and copper continuous converting process （CCCP）. Then, the CFCS thermodynamic model was proposed by establishing the multi-phase equilibrium model of FMSP and the local-equilibrium model of CCCP, respectively, and by combining them through the smelting intermediates. Subsequently, the influences of the furnace structures were investigated using the model on the formation of blister copper, the Fe3O4 behavior, the copper loss in slag and the copper recovery rate. The results show that the type D furnace, with double flues and a slag partition wall, is an ideal CFCS reactor compared with the other three types furnaces. For CFCS, it is effective to design a partition wall in the furnace to make FMSP and CCCP perform in two relatively independent zones, respectively, and to make smelting gas and converting gas discharge from respective flues.

Effect of moderately thermophilic bacteria on metal extraction and electrochemical characteristics for zinc smelting slag in bioleaching system

The effects of moderately thermophilic bacteria on the extraction of metals from zinc smelting slag and electrochemical characteristics of zinc smelting slag carbon paste electrode in bioleaching process were studied. The results show that the extraction rates of Fe, Cu and Zn from the slag reach 86.7%, 90.3% and 66.7% after adsorbed bacteria sterilize, while those with adsorbed bacteria are 91.9%, 96.0% and 84.5% in conditions of pulp density 2%, pH 1.0, temperature 65 °C and stirring rate 120 r/min, respectively. Some stretching peaks of functional groups from bacterial secretes on the bioleached residue surface, such as 1007 cm-1 and 1193 cm-1, turn up through FI-IR analysis and indirectly reveal the presence of the adsorbed bacteria on the slag particles surface. Besides, the corrosion of zinc smelting slag is enhanced by bacteria according to the characteristics of cyclic voltametry and Tafel curves in bioleaching system.

Environmental risk assessment on slag and iron-rich matte produced from reducing-matting smelting of lead-bearing wastes and iron-rich wastes

A new process for utilization of hazardous lead-bearing wastes and iron-rich wastes by reducing-matting smelting has been developed.The slag（SG） and the iron-rich matte（IRM） are the main by-products from reducing-matting smelting of lead-bearing wastes and iron-rich wastes.The environmental risk of heavy metals（Cd,Zn,Pb and As） in the main by-products versus the charging material for reducing-matting smelting（CM） has been systematically assessed using leaching toxicity test,the three-stage sequential extraction procedure of European Community Bureau of Reference（BCR） and Hakanson Potential Ecological Risk Index Method（PERI）.The results demonstrate that the ecological risk level of heavy metals for SG and IRM is significantly reduced after the reducing-matting smelting process compared with that for CM.

RESEARCH ON SMELTING LOW-CARBON FERROCHROME IN A PLASMA FURNACE

By a non-transformed arc plasma torch whose gas is nitrogen,scrap of high-carbon ferrochrome was heated and melted in a sealed furnace. When the liquid bath was at 1600℃,top blowing of oxygen began to decrease the bath's carbon without stopping plasma operation for its temperature addition and maintennace of at least 1750 ℃. The liquid bath was agitated by bottom-blowning nitrogen. In the experiments low carbon Fe-Cr have been obtained whose composition respectively was 0.45% carbon,50.75% chrome and 0.42% carbon, 70.25% chrome. Loss of chrome could be less than 5%.

Risk assessment of heavy metals in soils and vegetables around nonferrous metals mining and smelting sites,Baiyin,China

A field survey was conducted to investigate the metal and arsenic contamination in soils and vegetables on four villages （Shuichuan （SCH）, Beiwan （BWA）, Dongwan （DWA） and Wufe （WFE）） located along, Baiyin, China, and to evaluate the possible health risks to local population through foodchain. Results show that the most significantly contaminated soils occurred upstream at SCH where Cd, Cu and As concentrations exceeded maximum allowable concentrations for Chinese agricultural soil. Further downstream the degree of contamination semi-systematically decreased in concentrations of metal. Generally, the leafy vegetables were more heavily contaminated than non-leafy vegetables. Chinese cabbage is the most severely contaminated, the concentrations of Cd exceeded the maximum permit levels （0.05 mg/kg） by 4.5 times. Bio-accumulate factor also shows that an entry of Cd to food chain plants is the greatest potential. Furthermore, the estimated daily intake amounts of the considered toxic elements （Cd, Pb and Cu） from the vegetables grown at SCH and BWA and DWA have exceeded the recommended dietary allowance levels. Thus, the vegetables grown in three villages above, which affected by Baiyin mining and smelting have a health hazard for human consumption.