CURE CHARACTERISTICS OF HYDROXYL TERMINATED POLYBUTADIENE PREPOLYMER WITH BLOCKED TOLUENE DIISOCYANATE-Ⅰ

Controlled release of TDI and hence the cure characteristics of several blocked TDI with HTPB are reported. The reactions were followed through viscosity measurements as a function of time and temperature under the catalytic influence of triethylamine. The effect of nature of substituents present on the end capping substrate, temperature, solvent, basicity of catalyst and kinetics thereon have been studied.

Determination of toluene diisocyanate in synthetic-rubber track by ion chromatography with ultraviolet detection after alkaline suppressor

In the present work, a novel analytical method was proposed for the determination of toluene diisocyanate （TDI） in syntheticrubber track by ion chromatography （IC） coupled with an ultraviolet detector setting at 212 nm. TDI can be hydrolyzed to toluene diamine （TDA） which can be separated by cation-exchange IC easily. The optimum IC separation was performed on an IonPac CS12A column （150 mm ×4.0 mm） using 20 mmol L^-1 sodium sulfate, 10 mmol L^-1 sulfuric acid and 10% acetonitrile as eluent. It was found that a higher signal response of TDA could be obtained under alkaline condition. A suppressor was used to change the acidic eluent into alkaline one. 0.8 mol L^-1 potassium hydroxide was chosen as the optimum regeneration eluent. With the added suppressor and regenerant, signal response was magnified by about 16 times and lower limit of detection （LOD, 0.13 μg L^-1） was obtained. Within-day relative standard deviation （R.S.D.） was less than 3.6%. The recoveries of TDI spiked in synthetic-rubber track samoles were 96.4-110.6%.

Kinetics of the decomposition of dimethylhexane-1,6-dicarbamate to1,6-hexamethylene diisocyanate

The kinetics of the decomposition of dimethylhexane-1,6-dicarbamate to 1,6-hexamethylene diisocyanate was studied. A consecutive reaction model was established and the reaction orders for the two steps were confirmed to be 1 and 1.3 by the integral test method and the numerical differential method, respectively. The activation energies of the two steps were （56.94 4±5.90） kJ·mol^-1 and （72.07±3.47） kJ·mol^-1 with the frequency factors exp（ 12.53±1.42） min^- 1 and （ 14.254±0.84） tool^-0.33. L^0.33·min^-1, respectively. Based on the kinetic model obtained, the progress of the reaction can be calculated under given conditions.

CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅰ.POLY(P-PHENYLENE TEREPHTHALATE)

The morphology and crytal structure of poly(p-phenylene terephthalate) (PPT), prepared by confined thin filmmelt (CTFMP) and solution (CTFSP) and bulk solution polymerization, were characterized by transmission electronmicroscopy, electron dimaction and molecular modeling. The unit cell is monoclinic (P2_1/a space group) with parameters a =7.89, b = 5.49, c = 12.65 A, α=γ= 90°, β=100.33°, density = 1.48 g/cm^3, the a, b and β values differing slightly from thosereported previously in the literature. A degree of variation in relative intensities of hk0 reflections in, apparently, untilted[001] ED patterns was observed from a given sample, suggesting some variation in molecular packing. ED evidence wasfound for a second phase, with [001] appearing the same as for phase Ⅱ of the related poly(p-oxybenzoate) (PpOBA)polymer. CTFMP crystals polymerized above 220℃ (up to 370℃) and CTFSP crystals polymerized at 300℃ consisted oflamellae 100-200 A thick.

~1H NMR analysis of the tolylene-2,4-diisocyanate-methanol reaction

Tolylene-2,4-diisocyanate（2,4-TDI） 1 reacts with methanol through two simultaneous paths in the polyurethane reaction,which involve two different intermediates-tolylene-4-carbamatic-2-isocyanate 2 and tolylene-2-carbamatic-4-isocyanate 3,and the final product is tolylene-2,4-dicarbamate 4.The-CH_3 chemical shifts in benzene ring in compounds 1,2,3 and 4 can be easily tested and well distinguished,through which those four compounds are quantified and their kinetics are investigated.It shows that four rate constants for the tolylene-2,4-diisocyanate-methanol reaction in CCl_4 at 50℃are k_1=9.6×10^（-2）h^（-2）mol^（-2）min^（-1）, k_2=1.4×10^（-2）h^（-2）mol^（-2）min^（-1）,k_3=4.0×10^（-3）h^（-2）mol^（-2）min^（-1）,k_4=1.4×10^（-3）h^（-2）mol^（-2）min^（-1）.（k_1 is the reaction rate constant from compounds 1 to 2;k_2 is the reaction rate constant from compounds 1 to 3;k_3 is the reaction rate constant from compounds 3 to 4;k_4 is the reaction rate constant from compounds 2 to 4）.

Synthesis and photochromic behavior of mono-,and biphotochromic system linked by p-phenylene bridge

The synthesis of mono- and bis-1,3-diazabicyclo[3.1.0]hex-3-ene derivatives with indole ring and p-phenylene spacer, which behave as photochromic materials, is reported. The structure-photochromic behavior relationship （SPBR） of the synthesized compounds has been analyzed.

Effect of Added Poly (vinyl pyrrolidone) during Condensation on Properties of Poly(p-phenylene terephthalamide)Pulp

Poly(p-phenylene terephthalamide)(PPTA)pulp was prepared by polycondensation of the p-phenylene diamine(PPDA)with terephthaloyl chloride(TPC)in the completely anhydrous solvent system of N-methyl pyrrolidone(NMP)having calcium chloride,in the presence of poly(vinyl pyrrolidone)(PVP)having a viscosity average molecular weight lower than 40 000.It was confirmed that the polycondensation could be accelerated,the inherent viscosity of the polymer could be increased,and the polymers could be fibrillated more easily by the addition of the PVP.FTIR and X-ray spectra proved that PVP had not combined into molecular chains of the resultant PPTA pulps.The morphology of the resultant pulps,the effect of viscosity average molecular weight,amount and adding mode of PVP on inherent viscosity,specific surface area,and mean length of the resultant pulps were discussed in detail.And the friction and wear properties of the compound reinforced by the resultant pulps were simply investigated.

DIBUTYLTIN DILAURATE-CATALYZED DIISOCYANATE COUPLING—GRAFTING OF POLY(ETHYLENE GLYCOL)ONTO NANO-SILICA SURFACE THROUGH A ONE-STEP PROCEDURE

Grafting polymer glycols onto nano-silica surface through one-step procedure was investigated.The major characteristic of this procedure is that all the materials and reagents(silica,PEG,TDI,DBTDL,solvent)required for grafting were added simultaneously into the reaction vessel.TDI and DBTDL were used as coupling agent and catalyst,respectively. The products were characterized by FTIR,TGA,elemental analyses and TEM,giving evidence for successful grafting of PEG.Possible mechanism of this grafting was studied and two grafting processes were proposed.The process through which the grafting proceeds depends on the reaction temperature.Effect of molecular weight of PEG on grafting was also investigated.

Non-phosgene synthesis of hexamethylene-1,6-diisocyanate from thermal decomposition of hexamethylene-1,6-dicarbamate over Zn–Co bimetallic supported ZSM-5 catalyst

A non-phosgene route for the synthesis of hexamethylene-1,6-diisocyanate(HDI) was developed via catalytic decomposition of hexamethylene-1,6-dicarbamate(HDC) over Zn–Co bi-metallic supported ZSM-5 catalyst.The catalyst was characterized by FTIR and XRD analyses. Three solvents dioctyl sebacate(DOS), dibutyl sebacate(DBS) and 1-butyl-3-methylimidazolium tetrafluoroborate(BMIMBF_4) were investigated and compared; DOS gave better performance. The catalytic performances for thermal decomposition of HDC to HDI using DOS as solvent were then investigated, and the results showed that, under the optimized reaction conditions, i.e.,10 wt%concentration of HDC in DOS, 250 °C temperature, 60 min reaction time, 83.8% yield of HDI had been achieved over Zn–Co/ZSM-5. Decomposition of the intermediate hexamethylene-1-carbamate-6-isocyanate(HMI) over Zn–Co/ZSM-5 in DOS solvent was further studied and the results indicated that yield of HDI from HMI reached to 69.6%(98.6% HDI selectively) at 270 °C, which further increased the yield of the total HDI(HDI_(tol)) to as high as 95.0%. Recycling of catalyst showed that HDI and HMI yield slightly decreased, and by-product yield increased after the catalyst was reused for 4 times. At last possible reaction mechanism was proposed.

CURE CHARACTERISTICS OF HYDROXYL TERMINATED POLYBUTADIENE PREPOLYMER WITH BLOCKED TOLUENE DIISOCYANATE-Ⅱ

Cure characteristics of hydroxyl terminated polybutadiene (HTPB) prepolymer with avariety of blocked toluene diisocyanate (TDI) in the presence of triethylamine (TEA) andchloroacetic acid catalyst are reported. Phenol, thiophenol, p-chloropheno1, p-nitrophenol,p-cresol, resorcinol, naphthols, caprolactam and butylated-hydroxytoluene were used as blockingagents. Viscosity measurements have been carried out using a mixture of HTPB and blocked TDIin cyclohexanone in the presence of the catalysts at 50℃ and 60℃ using Haake rotational vis-cometer. Viscosity measurements have also been carried out with 50% solids such as ammonium sulphate along with HTPB and TDI adduct.

The Curing for Modified Vinyl Ester Resin by Hexamethylene Diisocyanate and Its Influence on Performances

The commercial vinyl ester resins(VER)was modified by diphenylmethane diisocyanate(MDI)to enhance its toughness,which is called MVER.Hexamethylene diisocyanate(HDI),a common curing agent for polyurethane(PU),was found to be a reactive agent for MVER and can contribute to the toughness of MVER.Based on present experiment results,the crosslinking mechanism of MVER and HDI system is very similar to that of PU.The FTIR result shows the-NCO of HDI can react with the-OH of MVER.The microstructure of material prepared by MVER and HDI was characterized by NMR,and it was revealed that the unique microstructure leads to the good performances.The different content of HDI has an influence on the microstructure,and the microstructure gradually reduces the toughness and mechanical performances of the MVER cured with increasing concentration of reactive curing agent(HDI).This feature is consistent with a maximum in toughness as a function of the additive(HDI)content,followed by a rapid deterioration in toughness at higher concentrations.The toughness exhibits the maximum at such an HDI concentration(20wt%).Therefore,the special curing agent(HDI)and reactive mode is very important to the microstructure and mechanical properties of material.Furthermore,there should be other reactions which contribute to the curing and microstructure of the material,which needs the further research.

Synthesis and Properties of Organic-Inorganic Hybrid Porous Polymers Obtained with Click Addition Reactions of Thiol-Functionalized Random Type Silsesquioxane by and Diacrylate or Diisocyanate Compounds

Organic-inorganic hybrid network polymers have been synthesized by addition reaction of a thiol-functionalized random type silsesquioxane (SQ109) and alkyl diacrylate or diisocyanate compounds. Thiol-ene reaction of SQ109 and 1,4-butanediol diacrylate (BDA) successfully yield porous polymer in toluene initiated by azobis(isobutyronitrile) (AIBN) at 60°C. Morphology of the porous polymers was composed by connected globules, and the diameter of the globules decreased with increasing in the monomer concentration of the reaction system. By contrast, the reaction with 1,6-hexanediol diacrylate or 1,5-hexadiene yielded homogeneous clear gels. Thermal analyses of SQ109-BDA porous polymers indicated that thermal degradation of ester groups of BDA in the polymer network occurred at around 300°C. The porous polymer was also obtained by the reaction using a photo-initiator (Irugacure184) at room temperature, and showed higher Young’s modulus than the corresponding porous polymer obtained with the reaction with AIBN due to the small size of the globules. Young’s modulus of SQ109-BDA porous polymer increased with increasing in the monomer concentration of the reaction systems. Thiolisocyanate addition reactions between SQ109 and hexamethylene diisocyanate (HDI) or methylenediphenyl 4,4’-diisocyanate (MDI) were investigated to obtain network polymers. The reactions in toluene yielded the corresponding homogeneous clear gels. By contrast the reactions in a mixed solvent of toluene (50 vol.%) and N,N-dimethylformamide (50 vol.%) produced porous polymers. The morphology of the porous polymers was composed by connected globules or aggregated particles. The size of globules and particles in the SQ109-HDI porous polymers was larger than those in the SQ109-MDI porous polymers. Thermal degradation of SQ109-HDI and SQ109-MDI porous polymers started at round 260°C and showed endothermic peak at around 350°C derived from degradation of thio-urethane bond.

CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅱ. POLY(p-PHENYLENE 2,6-NAPHTHALATE)

Confined thin film melt polymerization (CTFMP) of naphthalene chloride/hydroquinone (NCMQ, 1/1, molar)mixtures at polymerization temperatures (T_p) below ca. 300℃ resulted in relatively thick, elongated crystals. Polymerizationof NC/HQ above 300℃ between glass yielded well-formed lamellar crystals ca. 100 A thick. Phase Ⅰ and Ⅱ [001] EDpatterns were obtained for all T_p, the relative amount of phase Ⅰ increasing with T_p. Polymerization of naphthalenedicarboxylic acid/hydroquinione diacetate 1/1 mixtures at high T_p also yielded lamellar crystals that "curled up" off of thesubstrate. When the high temperature CTFMP polymerization was conducted between mica, aggregates of lamellae on-edgedeveloped but epitaxial growth did not occur. Epitaxial growth of lamellae between mica could be obtained, however, byconfined thin film solution polymerization, with both of the latter samples yielding apparently related ED patterns from adifferent unit cell than phase Ⅰ or Ⅱ. Fiber patterns, obtained from sheared samples, indicated considerably greater crystaldisorder than in the nascent crystals. Refinement of the phase Ⅰ unit cell parameters, based on the [001] and [01 1] EDpatterns, with modeling based on Cerius^2, suggests a monoclinic phase Ⅰ unit cell with a = 7.76, b = 5.71, c = 14.99 A, α = γ= 90°, β= 99.7°, ρ = 1.47 g/cm^3, space group P12_1/al.

Study on the behaviors of poly（p-phenylene benzobisoxazole） in coagulation

Poly（p-phenylene benzobisoxazole）（PBO） is a candidate of high performance materials for many applications. PBO materials＇ properties are considered to be closely related to their fabrication process, especially coagulation. In this paper, the coagulation effect on the chemical and microstructure of PBO was investigated with the help of a PBO model compound, 2, 2＇-（ 1,4-phenylene） bis （5-amino-6-benzoxazolole）. During coagulation, the hetero-cyclic ring of the PBO structure was experienced cleavage and even being broken down completely under some extreme conditions. Wide-angle X-ray diffraction （WAXD） analysis showed that different coagulants could cause the microstructure difference in PBO materials. In a slow coagulation process, PBO molecular chains aligned more orderly in the side-by-side direction （200）.

A STUDY OF PACKING STRUCTURE OF POLY(P-PHENYLENE BENZOBISTHIAZOLE)BY MOLECULAR SIMULATION

Molecular simulation technique was used in an examination of the possibilities of chain packing in the crystalline state for poly(ρ-phenylene benzobisthiazole).It has been found that one reason of hardly forming very ordered crystal of the polymer is the existence of so many stable positions of interchain interaction along chain axis.

Mechanical Property and Crystal Structure of Poly(p-phenylene terephthalamide)(PPTA) Fibers during Heat Treatment under Tension

The relationship between property and structure of poly( p-phenylene terephthalamide)( PPTA) was investigated for the purpose of obtaining products with better performance. PPTA fiber subjected to heat treatment under different conditions was intensively studied. Simultaneous wide-angle X-ray diffraction( WAXD) technique was introduced to study the changes of crystal structure. It was found that the tensile modulus was strongly sensitive to the levels of temperature and tension. The structure parameters including crystal size and crystal orientation after heat treatment evolve similarly to the tensile modulus,indicating a direct structure-property relationship. The lattic c-dimension increases after heat treatment and is greatly affected by the tension. An optimal temperature can be found around 400 ℃,where big change can happen in the crystal structure due to α-relaxation in the crystal region as supported in dynamic mechanical analysis( DMA).

The Synthesis and Electronic Characteristics of Poly(p-Phenylene Vinylene) Derivatives

A series of soluble poly(p-phenylene vinylene) (PPV) derivatives were synthesized through dehydrochlorination with the p-metaoxy phenol as starting materials. The electronic characteristics of PPV derivatives were studied.

An efficient green route for hexamethylene-1,6-diisocyanate synthesis by thermal decomposition of hexamethylene-1,6-dicarbamate over Co3O4/ZSM-5 catalyst： An indirect utilization of CO2

The utilization of CO2 as raw material for chemical synthesis has the potential for substantial economic and green benefits. Thermal decomposition of hexamethylene-1,6-dicarbamate （HDC） is a promising approach for indirect utilization of CO2 to produce hexamethylene-1,6-diisocyanate （HDI）. In this work, a green route was developed for the synthesis of HD1 by thermal decomposition of HDC over Co3O4/ZSM-5 catalyst, using chlorobenzene as low boiling point solvent. Different metal oxide supported catalysts were prepared by incipient wetness impregnation （IWI）, PEG-additive （PEG） and deposition precipitation with ammonia evaporation （DP） methods. Their catalytic performances for the thermal decomposition of HDC were tested. The catalyst screening results showed that Co3O4/ZSM-525 catalysts prepared by different methods showed different performances in the order of Co3O4/ZSM-5 25（PEG） 〉 Co3O4/ZSM-525（IWI） 〉 Co3O4/ZSM-525（DP）. The physicochemical properties of Co3O4/ZSM- 52s catalyst were characterized by XRD, FTIR, N2 adsorption-desorption measurements, NH3-TPD and XPS. The superior catalytic performance of Co3O4/ZSM-52S（PEG） catalyst was attributed to its relative surface content of Co3 ＋, surface lattice oxygen content and total acidity. Under the optimized reaction conditions： 6.5% HDC concentration in chlorobenzene, 1 wt% Co3O4/ZSM-525（PEG） catalyst, 250℃ temperature, 2.5 h time, 800 ml.min 1 nitrogen flow rate and 1.0 MPa pressure, the HDC conversion and HDI yield could reach 100% and 92.8% respectively. The Co3O4/ZSM-525（PEG） catalyst could be facilely separated from the reaction mixture, and reused without degradation in catalytic performance. Furthermore, a possible reaction mechanism was proposed based on the physicochemical properties of the Co3O4/ZSM-5 25 catalysts.