Afterburning behind the detonation front of an aluminized explosive releases energy on the millisecond timescale,which prolong the release of detonation energy and the energy release at different stages also shows sig...Afterburning behind the detonation front of an aluminized explosive releases energy on the millisecond timescale,which prolong the release of detonation energy and the energy release at different stages also shows significant differences.However,at present,there are few effective methods for evaluating the energy release characteristics of the middle reaction stage of such explosives,which can have a duration of tens to hundreds of microseconds.The present work demonstrates an approach to assessing the midstage of an aluminized explosive detonation based on a water push test employing a high degree of confinement.In this method,the explosive is contained in a steel cylinder having one end closed that is installed at the bottom of a transparent water tank.Upon detonation,the gaseous products expand in one direction while forcing water ahead of them.The resulting underwater shock wave and the interface between the gas phase products and the water are tracked using an ultra-high-speed framing and streak camera.The shock wave velocity in water and the expansion work performed by the gaseous detonation products were calculated to assess the energy release characteristics of aluminized explosives such as CL-20 and RDX in the middle stage of the detonation reaction.During the middle stage of the detonation process of these aluminized explosives,the aluminum reaction reduced the attenuation of shock waves and increased the work performed by gas phase products.A higher aluminum content increased the energy output while the presence of oxidants slowed the energy release rate.This work demonstrates an effective means of evaluating the performance of aluminized explosives.展开更多
Taking CL-20(Hexanitrohexaazaisowurtzitane)-based aluminized explosives with high gurney energy as the research object, this research experimentally investigates the work capability of different aluminized explosive f...Taking CL-20(Hexanitrohexaazaisowurtzitane)-based aluminized explosives with high gurney energy as the research object, this research experimentally investigates the work capability of different aluminized explosive formulations when driving metal flyer plates in the denotation wave propagation direction.The research results showed that the formulations with 43 μm aluminum(Al) powder particles(The particle sizes of Al powder were in the range of 2~43 μm) exhibited the optimal performance in driving flyer plates along the denotation wave propagation direction. Compared to the formulations with Al powder 13 μm, the formulations with Al powder 2 μm delivered better performance in accelerating metal flyer plates in the early stage, which, however, turned to be poor in the later stage. The CL-20-based explosives containing 25% Al far under-performed those containing 15% Al. Based on the proposed quasi-isentropic hypothesis, relevant isentropy theories, and the functional relationship between detonation parameters and entropy as well as Al reaction degree, the characteristic lines of aluminized explosives in accelerating flyer plates were theoretically studied, a quasi-isentropic theoretical model for the aluminized explosive driving the flyer plate was built and the calculation methods for the variations of flyer plate velocity, Al reaction degree, and detonation product parameters with time and axial positions were developed. The theoretical model built is verified by the experimental results of the CL-20-based aluminized explosive driving flyer plate. It was found that the model built could accurately calculate the variations of flyer plate velocity and Al reaction degree over time. In addition, how physical parameters including detonation product pressure and temperature varied with time and axial positions was identified. The action time of the positive pressure after the detonation of aluminized explosives was found prolonged and the downtrend of the temperature was slowed down and even reversed to a slight rise due to the aftereffect reaction between the Al powder and the detonation products.展开更多
Based on the data of outcrop,core,logging,gas testing,and experiments,the natural gas accumulation and aluminous rock mineralization integrated research was adopted to analyze the controlling factors of aluminous rock...Based on the data of outcrop,core,logging,gas testing,and experiments,the natural gas accumulation and aluminous rock mineralization integrated research was adopted to analyze the controlling factors of aluminous rock series effective reservoirs in the Ordos Basin,NW China,as well as the configuration of coal-measure source rocks and aluminous rock series reservoirs.A natural gas accumulation model was constructed to evaluate the gas exploration potential of aluminous rock series under coal seam in the basin.The effective reservoirs of aluminous rock series in the Ordos Basin are composed of honeycomb-shaped bauxites with porous residual pisolitic and detrital structures,with the diasporite content of greater than 80%and dissolved pores as the main storage space.The bauxite reservoirs are formed under a model that planation controls the material supply,karst paleogeomorphology controls diagenesis,and land surface leaching improves reservoir quality.The hot humid climate and sea level changes in the Late Carboniferous–Early Permian dominated the development of a typical coal-aluminum-iron three-stage stratigraphic structure.The natural gas generated by the extensive hydrocarbon generation of coal-measure source rocks was accumulated in aluminous rock series under the coal seam,indicating a model of hydrocarbon accumulation under the source.During the Upper Carboniferous–Lower Permian,the relatively low-lying area on the edge of an ancient land or island in the North China landmass was developed.The gas reservoirs of aluminous rock series,which are clustered at multiple points in lenticular shape,are important new natural gas exploration fields with great potential in the Upper Paleozoic of North China Craton.展开更多
This study reports the significantly enhanced aluminizing behaviors of a low carbon steel at temperatures far below the austenitizing temperature, with a nanostructured surface layer produced by surface mechanical att...This study reports the significantly enhanced aluminizing behaviors of a low carbon steel at temperatures far below the austenitizing temperature, with a nanostructured surface layer produced by surface mechanical attrition treatment (SMAT). A much thicker iron aluminide compound layer with a much enhanced growth kinetics of η-Fe2Al5 in the SMAT sample has been observed relative to the coarse-grained steel sample. Compared to the coarse-grained sample, a weakened texture is formed in the aluminide layer in the SMAT sample. The aluminizing kinetics is analyzed in terms of promoted difusivity and nucleation frequency in the nanostructured surface layer.展开更多
Al-containing coatings were prepared on AZ31 magnesium alloy by pack-cementation technology.X-ray diffraction(XRD),backscattered electron imaging(BSEI)and energy dispersive spectroscopy(EDS)were jointly employed to ch...Al-containing coatings were prepared on AZ31 magnesium alloy by pack-cementation technology.X-ray diffraction(XRD),backscattered electron imaging(BSEI)and energy dispersive spectroscopy(EDS)were jointly employed to characterize the phases,microstructure and composition of the coated samples.The results show that the feedstock composition has a significant impact on the phases,microstructure and thickness of the coatings.For the sample with AlCl3 powder as the activator,the coating is very thick and composed of gradient phases and structures from surface to inside,including small amount ofb-Mg2Al3,coarse eutectic-like structure ofγ-Mg17Al12+δ-Mg,and fineγ-Mg17Al12 precipitations.In contrast,for the sample with AlCl3 and pure Al composite powders as the activator,the coating is relatively thin and contains a thin Al2O3 layer and a small amount of fineγ-Mg17Al12 precipitates.For the pack-cementation aluminizing that is not protected by high-vacuum or inert gas,the addition of pure Al powders can easily introduce the Al2O3 layer into the coating to prevent active Al ions further penetrating into the magnesium matrix,resulting in the thin Al-containing coating.The microhardness and corrosion behavior of the two kinds of aluminized coatings were also studied and discussed.展开更多
Aluminizing coating and aluminizing-dispersed Y 2O 3 composite coating were prepared on 20 steel specimens by pulsed spark technique, which exhibited a micro-crystallized structure with grain size in the range of se...Aluminizing coating and aluminizing-dispersed Y 2O 3 composite coating were prepared on 20 steel specimens by pulsed spark technique, which exhibited a micro-crystallized structure with grain size in the range of several ten to several hundred nanometers. It is shown that, after oxidation at 600 ℃ in air for 100 h, these two kinds of coatings have excellent resistance to high temperature oxidation and scale spallation, and the aluminizing-dispersed Y 2O 3 composite coating has even better property than the aluminizing coating. AFM, SEM, EDS and XRD were applied to analyze the surface morphology, composition and phases structure of these coatings and the oxide scale formed in oxidation. The mechanism for these coatings that how to enhance the oxidation resistance and scale spallation resistance was discussed by considering the factors, such as Al concentration on the selective oxidation of Fe-Al alloy, the effect of micro-crystallization, reactive element effect (REE) caused by dispersed Y 2O 3, etc.展开更多
Hot dip aluminizing is one of the most effective methods of surface protection for steels and is gradually gaining popularity.Although the pulling speed is one of the most important parameters to control the coating t...Hot dip aluminizing is one of the most effective methods of surface protection for steels and is gradually gaining popularity.Although the pulling speed is one of the most important parameters to control the coating thickness of aluminizing products,however,there are few publications on the mathematical modeling of pulling speed during the hot dip process.In order to describe the correlation among the pulling speed,coating thickness and solidification time,the principle of mass and heat transfer during the aluminizing process is investigated in this paper.The mathematical models are based on Navier-Stokes equation and heat transfer analysis.Experiments using the self-designed equipment are carried out to validate the mathematical models.Specifically,aluminum melt is purified at 730 ℃.The Cook-Norteman method is used for the pretreatment of Q235 steel plates.The temperature of hot dip aluminizing is set to 690 ℃ and thedipping time is set to 3 min.A direct current motor with stepless speed variation is used to adjust the pulling speed.The temperature change of the coating is recorded by an infrared thermometer,and the coating thickness is measured by using image analysis.The validate experiment results indicate that the coating thickness is proportional to the square root of pulling speed for the Q235 steel plate,and that there is a linear relationship between coating thickness and solidification time when the pulling speed is lower than 0.11 m/s.The prediction of the proposed model fits well with the experimental observations of the coating thickness.展开更多
Pure titanium samples were aluminized at 950,1025 and 1100 ℃ for 0-6 h in a pack containing 10%Al+5%NaF+85%Al2O3 in mass traction.The aluminized layers formed on the samples were characterized.The kinetic studies i...Pure titanium samples were aluminized at 950,1025 and 1100 ℃ for 0-6 h in a pack containing 10%Al+5%NaF+85%Al2O3 in mass traction.The aluminized layers formed on the samples were characterized.The kinetic studies indicated that the diffusion of Al-bearing gases through the pack is the rate-controlling step in this process.The activation energy of 161.8 kJ/mol was calculated for this step.In addition,the mass gains of the aluminized samples were predicted using the partial pressures of gases in the pack and those adjacent to the samples surface.The predicted values are in good agreement wim the experimental measurements at 950 ℃ but are higher than those measured at 1025 and 1100 ℃.展开更多
Aluminizing of Cu by a pack cementation process was performed to improve its surface properties.The effect of variation of pack aluminizing temperature from 800 to 900℃ and aluminizing time from 1 to 6 h on the micro...Aluminizing of Cu by a pack cementation process was performed to improve its surface properties.The effect of variation of pack aluminizing temperature from 800 to 900℃ and aluminizing time from 1 to 6 h on the microstructure and the thickness of the aluminide coating of Cu was investigated. Pack aluminizing of Cu significantly improved the microhardness and the oxidation resistance. The microhardness was increased about seven times and the oxidation resistance,after 96 h exposure in air at 900℃, was extremely increased ten times by aluminizing Cu at 900℃ for 3 h.展开更多
IN 600 alloy was coated with two different types of coatings, Cr-modified aluminide coating this is called aluminizing-chromizing and Y-doped chromium modified aluminide coating this is called aluminizing-chromizing-y...IN 600 alloy was coated with two different types of coatings, Cr-modified aluminide coating this is called aluminizing-chromizing and Y-doped chromium modified aluminide coating this is called aluminizing-chromizing-yttriumizing. Diffusion coating was carried at 1 050℃ for 8 h under Ar atmosphere by simultaneous aluminizing-chromizing process and by simultaneous aluminizing-chromizing- yttriumizing. Cyclic oxidation tests were conducted on the uncoated and on the coated Inconel 600 alloy in the temperature range 800- 1 000℃ in CO2 for 100 h at 10 h cycle.The results showed that the oxidation kinetics for uncoated Inconel 600 alloy in CO2 is parabolic and the phases present are NiO, (Fe, Cr)2O3 , NiFe2O4 and NiCrO4. The oxidation kinetics for both coated systems in CO2 was found to be parabolic and the value ofkp for both coated systems were found to be lower than that for uncoated Inconel 600 alloy. Oxide phases that formed on coated systems are Al2O3 and NiCrO4. The role of yttrium can be attributed to its ability to improve the adherence of the oxide scale.展开更多
The steel surface treatment by rare-earth aluminithermic aluminizing,which was utilized onthermal couple,buried parts of lightning arrester and silencer of automobile,has met with success.This new technique was studie...The steel surface treatment by rare-earth aluminithermic aluminizing,which was utilized onthermal couple,buried parts of lightning arrester and silencer of automobile,has met with success.This new technique was studied by Beijing University of Science and Technology,BeijingIron-steel Institute and Jingdong Work of Corrosion-protective Materials cooperatively.The steel展开更多
This paper describes a study on the corrosion behavior of steel reinforcement in CAC mortars via electrochemical methods including corrosion potential,electrochemical impedance,and linear polarization evaluation.Resul...This paper describes a study on the corrosion behavior of steel reinforcement in CAC mortars via electrochemical methods including corrosion potential,electrochemical impedance,and linear polarization evaluation.Results indicate that there is a non-linear relationship between the corrosion degree of steel reinforcement in CAC mortar and the concentration of NaCl solution.The electrochemical parameters of specimens immersed in 3%NaCl solution suddenly drop at 40 days,earlier than 60 days of the reference.And the charge transfer resistivity of the specimen has decreased by 11 orders of magnitude at 40 days,showing an evident corrosion on steel reinforcement.However,it is interesting to notice that the corrosion is delayed by high external chloride concentration.The specimens immersed in 9%and 15%NaCl solutions remain in a relatively stable state within 120 days with slight pitting.The great corrosion protection of CAC concrete to embedded steel bars enables its wide application in marine.展开更多
Aluminous refractory materials with high alumina contents are widely used in the steel industry,and the higher the alumina content,the higher the working temperature.Properties such as high refractoriness and thermal ...Aluminous refractory materials with high alumina contents are widely used in the steel industry,and the higher the alumina content,the higher the working temperature.Properties such as high refractoriness and thermal shock resistance lead these refractory materials to be used as channel linings of blast furnaces,where they are exposed to the attack by slag,molten steel,working cycles and sudden temperature changes between 25℃(room temperature)and 1520℃(the temperature of molten pig iron).In this work,microstructural changes in post-mortem aluminous refractory bricks were investigated by apparent porosity,X-ray diffraction analysis(XRD),Fourier transform infrared spectroscopy(FTIR),scanning electron microscopy,and X-ray dispersion energy spectrometry(SEM/EDS).The results showed an increase in the apparent porosity and the bulk density and the presence of the phases mullite,sillimanite,alumina,and quartz in the post-mortem brick.Calcium and magnesium were not detected in the microstructure of the post-mortem brick,indicating that slags did not corrode these refractory materials.Therefore,the microstructural changes that occurred in the post-mortem bricks must be due to thermal cycling.In the X-ray diffraction(XRD)test,mullite,sillimanite,quartz,andα-alumina phases were identified.These results indicate that the aluminous refractory was obtained from sillimanite.In infrared spectroscopy(FTIR)it was possible to identify the vibration bands referring to the Si-O and Al-O bonds.The increase in the porosity is a result of cracks caused by work cycles at high temperatures and the temperature gradient to which the refractory was subjected during use.Through the micrograph it was possible to identify the presence of acicular mullite.The absence of magnesium and calcium in the microanalysis results by energy dispersed X-ray spectrometry(EDS)indicates that there was no infiltration by slag or liquid iron.These results indicate that the microstructural changes that occurred in the post-mortem aluminous refractory were of a thermal nature.展开更多
To improve the efficiency and stability of chloride immobilization of portland cement paste,hydrated calcium aluminate cement(HCAC)prepared by wet grinding of CAC was added into portland cement paste as an additive.Th...To improve the efficiency and stability of chloride immobilization of portland cement paste,hydrated calcium aluminate cement(HCAC)prepared by wet grinding of CAC was added into portland cement paste as an additive.The immobilized chloride ratio(ICR)was evaluated,and the mechanism of chloride immobilization was researched by XRD,DTG,NMR,and MIP tests.The analysis results demonstrated that HCAC could improve the chloride immobilization capacity of portland cement paste.The mechanism was attributed to the following aspects:chemical binding capacity was enhanced via producing more Kuzel’s salt;physical adsorption capacity was reduced by decreasing the C-S-H gel;migration resistance was enhanced through refining the pore structure.展开更多
In order to enhance the sintering resistance of lanthanum aluminate based high emissivity coatings,Ca^(2+)-Fe^(3+)doped LaAlO_(3)/ZrO_(2)specimens were prepared by solid state sintering using La_(2)O_(3),Al_(2)O_(3),C...In order to enhance the sintering resistance of lanthanum aluminate based high emissivity coatings,Ca^(2+)-Fe^(3+)doped LaAlO_(3)/ZrO_(2)specimens were prepared by solid state sintering using La_(2)O_(3),Al_(2)O_(3),CaCO_(3) and Fe_(2)O_(3) as raw materials,extra-adding fused Y_(2)O_(3)-stabilized ZrO_(2)(0,5%,10%,and 15%,by mass),ball milling,pre-calcining,pressing into shapes and sintering at 1600℃for 2 h.The effect of the ZrO_(2)addition on the properties of lanthanum aluminate based high emissivity coatings was explored.It is concluded that ZrO_(2)does not react with LaAlO_(3),which can inhibit the sintering of the specimens.With the increase of the ZrO_(2),addition,the linear shrinkage rate and the thermal conductivity decrease significantly,while the emissivity decreases,but the emissivity of all the specimens is all higher than 0.9.The optimal addition of ZrO_(2),is 10%.展开更多
Unburned magnesium aluminate spinel refractories were prepared using sintered magnesium aluminate spinel as the main raw material,phenolic resin as the binder,aluminum powder(2%,4%,and 6%by mass)and silicon powder(whe...Unburned magnesium aluminate spinel refractories were prepared using sintered magnesium aluminate spinel as the main raw material,phenolic resin as the binder,aluminum powder(2%,4%,and 6%by mass)and silicon powder(when Al powder addition is 4%,Si powder addition varies:1%and 2%,by mass)as additives.The effects of the Al powder and Si powder additions on the properties and microstructure of the refractories heat treated at different temperatures(1000,1400,and 1600℃for 3 h)were studied.The results show that the Al powder addition can greatly enhance the cold modulus of rupture of the samples fired at 1000 or 1400℃,and meanwhile AlN reinforcement phase forms in the matrix,which greatly improves the hot modulus of rupture of the samples at 1400℃;however,the heat treatment at 1600℃has little influence on the strength;the addition of Al powder and Si powder results in the formation of low melting point phases,greatly reducing the hot modulus of rupture.However,the low melting point phases promote sintering,which enhances the density and the cold modulus of rupture,and decreases the volume change during heating.The samples added with Al and Si all have higher cold modulus of rupture than those added with Al powder only.展开更多
The adsorption method has the advantages of low cost,high efficiency,and environmental friendliness in treating fluorinated wastewater,and the adsorbent material is the key.This study combines the inherent anion-excha...The adsorption method has the advantages of low cost,high efficiency,and environmental friendliness in treating fluorinated wastewater,and the adsorbent material is the key.This study combines the inherent anion-exchange adsorption properties of layered double hydroxides(LDHs).Self-supported porous adsorbent materials loaded with AFm and AFt were prepared from a composite cementitious system consisting of calcium aluminate cement(CAC)and flue gas desulfurization gypsum(FGDG)by chemical foaming technique.The mineral composition of the adsorbent material was characterized by X-ray diffraction(XRD)and Scanning electron microscopy(SEM).Through the static adsorption experiment,the adsorption effect of the mineral composition of the adsorbent on fluoride ions was deeply analyzed,and the adsorption mechanism was revealed.XRD and SEM showed that the main hydration phases of the composite cementitious system consisting of CAC and FGDG are AFm,AFt,AH_(3),and CaSO_(4)·2H_(2)O.FGDG accelerates the hydration process of CAC and inhibits the transformation of AFt to AFm.The AFt content increased,and the AFm content decreased or even disappeared as the amount of FGDG increased.Static adsorption experiment results showed that AFm and AFt in adsorbent materials could significantly enhance the adsorption of fluoride ions.The adsorption of F^(−)in aqueous solution by PAG tends more towards monolayer adsorption with a theoretical maximum capacity of 108.70 mg/g and is similar to the measured value of 112.77 mg/g.展开更多
The RE-aluminized coating and pure aluminized coating on 20 carbons steel were prepared by hot dip aluminizing method at 740℃. After diffusion treatment at 850℃for 4 h, the distribution of aluminum and lanthanum ele...The RE-aluminized coating and pure aluminized coating on 20 carbons steel were prepared by hot dip aluminizing method at 740℃. After diffusion treatment at 850℃for 4 h, the distribution of aluminum and lanthanum elements in the coating was analyzed with energy disperse spectroscopy(EDS) and electron probe microanalyses(EPMA), and the lattice parameter ofα-Fe in the matrix of the coating was measured precisely by X-ray diffractometer(XRD). The results show that RE permeates into the aluminized coating, leads to lattice disturbance and increases the depth of the aluminized coating. On the basis of the results, the expression of the diffusion coefficient of Al atoms is derived from the diffusion flow, and the effect of the high vacancy concentration and high concentration gradient of vacancies on the diffusion of Al atoms was analyzed by establishing the kinetics model of the vacancy mechanism of diffusion. The results show that the high vacancy concentration and high concentration gradient of vacancies in the RE-aluminized processes are the main reason why the diffusion coefficient of Al atoms in RE-aluminizing is bigger than that in pure aluminizing.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.11832006)。
文摘Afterburning behind the detonation front of an aluminized explosive releases energy on the millisecond timescale,which prolong the release of detonation energy and the energy release at different stages also shows significant differences.However,at present,there are few effective methods for evaluating the energy release characteristics of the middle reaction stage of such explosives,which can have a duration of tens to hundreds of microseconds.The present work demonstrates an approach to assessing the midstage of an aluminized explosive detonation based on a water push test employing a high degree of confinement.In this method,the explosive is contained in a steel cylinder having one end closed that is installed at the bottom of a transparent water tank.Upon detonation,the gaseous products expand in one direction while forcing water ahead of them.The resulting underwater shock wave and the interface between the gas phase products and the water are tracked using an ultra-high-speed framing and streak camera.The shock wave velocity in water and the expansion work performed by the gaseous detonation products were calculated to assess the energy release characteristics of aluminized explosives such as CL-20 and RDX in the middle stage of the detonation reaction.During the middle stage of the detonation process of these aluminized explosives,the aluminum reaction reduced the attenuation of shock waves and increased the work performed by gas phase products.A higher aluminum content increased the energy output while the presence of oxidants slowed the energy release rate.This work demonstrates an effective means of evaluating the performance of aluminized explosives.
基金National Natural Science Foundation of China(Grant No.11872120).
文摘Taking CL-20(Hexanitrohexaazaisowurtzitane)-based aluminized explosives with high gurney energy as the research object, this research experimentally investigates the work capability of different aluminized explosive formulations when driving metal flyer plates in the denotation wave propagation direction.The research results showed that the formulations with 43 μm aluminum(Al) powder particles(The particle sizes of Al powder were in the range of 2~43 μm) exhibited the optimal performance in driving flyer plates along the denotation wave propagation direction. Compared to the formulations with Al powder 13 μm, the formulations with Al powder 2 μm delivered better performance in accelerating metal flyer plates in the early stage, which, however, turned to be poor in the later stage. The CL-20-based explosives containing 25% Al far under-performed those containing 15% Al. Based on the proposed quasi-isentropic hypothesis, relevant isentropy theories, and the functional relationship between detonation parameters and entropy as well as Al reaction degree, the characteristic lines of aluminized explosives in accelerating flyer plates were theoretically studied, a quasi-isentropic theoretical model for the aluminized explosive driving the flyer plate was built and the calculation methods for the variations of flyer plate velocity, Al reaction degree, and detonation product parameters with time and axial positions were developed. The theoretical model built is verified by the experimental results of the CL-20-based aluminized explosive driving flyer plate. It was found that the model built could accurately calculate the variations of flyer plate velocity and Al reaction degree over time. In addition, how physical parameters including detonation product pressure and temperature varied with time and axial positions was identified. The action time of the positive pressure after the detonation of aluminized explosives was found prolonged and the downtrend of the temperature was slowed down and even reversed to a slight rise due to the aftereffect reaction between the Al powder and the detonation products.
基金Supported by the PetroChina Science and Technology Major Project(2021DJ2101).
文摘Based on the data of outcrop,core,logging,gas testing,and experiments,the natural gas accumulation and aluminous rock mineralization integrated research was adopted to analyze the controlling factors of aluminous rock series effective reservoirs in the Ordos Basin,NW China,as well as the configuration of coal-measure source rocks and aluminous rock series reservoirs.A natural gas accumulation model was constructed to evaluate the gas exploration potential of aluminous rock series under coal seam in the basin.The effective reservoirs of aluminous rock series in the Ordos Basin are composed of honeycomb-shaped bauxites with porous residual pisolitic and detrital structures,with the diasporite content of greater than 80%and dissolved pores as the main storage space.The bauxite reservoirs are formed under a model that planation controls the material supply,karst paleogeomorphology controls diagenesis,and land surface leaching improves reservoir quality.The hot humid climate and sea level changes in the Late Carboniferous–Early Permian dominated the development of a typical coal-aluminum-iron three-stage stratigraphic structure.The natural gas generated by the extensive hydrocarbon generation of coal-measure source rocks was accumulated in aluminous rock series under the coal seam,indicating a model of hydrocarbon accumulation under the source.During the Upper Carboniferous–Lower Permian,the relatively low-lying area on the edge of an ancient land or island in the North China landmass was developed.The gas reservoirs of aluminous rock series,which are clustered at multiple points in lenticular shape,are important new natural gas exploration fields with great potential in the Upper Paleozoic of North China Craton.
基金supported by the National Science Foundation of China (Nos.50701044 and 50890171)the Ministry of Science and Technology of China (No.2005CB623604)
文摘This study reports the significantly enhanced aluminizing behaviors of a low carbon steel at temperatures far below the austenitizing temperature, with a nanostructured surface layer produced by surface mechanical attrition treatment (SMAT). A much thicker iron aluminide compound layer with a much enhanced growth kinetics of η-Fe2Al5 in the SMAT sample has been observed relative to the coarse-grained steel sample. Compared to the coarse-grained sample, a weakened texture is formed in the aluminide layer in the SMAT sample. The aluminizing kinetics is analyzed in terms of promoted difusivity and nucleation frequency in the nanostructured surface layer.
基金the National Natural Science Foundation of China(No.51575073)International Cooperation Special Project in Science and Technology of China(No.2015DFR70480)Scientific and Technological Research Program of Chongqing,China(Nos.cstc2017jcyjBX0031,cstc2018jszx-cyzdX0126).
文摘Al-containing coatings were prepared on AZ31 magnesium alloy by pack-cementation technology.X-ray diffraction(XRD),backscattered electron imaging(BSEI)and energy dispersive spectroscopy(EDS)were jointly employed to characterize the phases,microstructure and composition of the coated samples.The results show that the feedstock composition has a significant impact on the phases,microstructure and thickness of the coatings.For the sample with AlCl3 powder as the activator,the coating is very thick and composed of gradient phases and structures from surface to inside,including small amount ofb-Mg2Al3,coarse eutectic-like structure ofγ-Mg17Al12+δ-Mg,and fineγ-Mg17Al12 precipitations.In contrast,for the sample with AlCl3 and pure Al composite powders as the activator,the coating is relatively thin and contains a thin Al2O3 layer and a small amount of fineγ-Mg17Al12 precipitates.For the pack-cementation aluminizing that is not protected by high-vacuum or inert gas,the addition of pure Al powders can easily introduce the Al2O3 layer into the coating to prevent active Al ions further penetrating into the magnesium matrix,resulting in the thin Al-containing coating.The microhardness and corrosion behavior of the two kinds of aluminized coatings were also studied and discussed.
文摘Aluminizing coating and aluminizing-dispersed Y 2O 3 composite coating were prepared on 20 steel specimens by pulsed spark technique, which exhibited a micro-crystallized structure with grain size in the range of several ten to several hundred nanometers. It is shown that, after oxidation at 600 ℃ in air for 100 h, these two kinds of coatings have excellent resistance to high temperature oxidation and scale spallation, and the aluminizing-dispersed Y 2O 3 composite coating has even better property than the aluminizing coating. AFM, SEM, EDS and XRD were applied to analyze the surface morphology, composition and phases structure of these coatings and the oxide scale formed in oxidation. The mechanism for these coatings that how to enhance the oxidation resistance and scale spallation resistance was discussed by considering the factors, such as Al concentration on the selective oxidation of Fe-Al alloy, the effect of micro-crystallization, reactive element effect (REE) caused by dispersed Y 2O 3, etc.
基金supported by Guangxi Provincial Natural Science Foundation of China (Grant No. 0832001)
文摘Hot dip aluminizing is one of the most effective methods of surface protection for steels and is gradually gaining popularity.Although the pulling speed is one of the most important parameters to control the coating thickness of aluminizing products,however,there are few publications on the mathematical modeling of pulling speed during the hot dip process.In order to describe the correlation among the pulling speed,coating thickness and solidification time,the principle of mass and heat transfer during the aluminizing process is investigated in this paper.The mathematical models are based on Navier-Stokes equation and heat transfer analysis.Experiments using the self-designed equipment are carried out to validate the mathematical models.Specifically,aluminum melt is purified at 730 ℃.The Cook-Norteman method is used for the pretreatment of Q235 steel plates.The temperature of hot dip aluminizing is set to 690 ℃ and thedipping time is set to 3 min.A direct current motor with stepless speed variation is used to adjust the pulling speed.The temperature change of the coating is recorded by an infrared thermometer,and the coating thickness is measured by using image analysis.The validate experiment results indicate that the coating thickness is proportional to the square root of pulling speed for the Q235 steel plate,and that there is a linear relationship between coating thickness and solidification time when the pulling speed is lower than 0.11 m/s.The prediction of the proposed model fits well with the experimental observations of the coating thickness.
文摘Pure titanium samples were aluminized at 950,1025 and 1100 ℃ for 0-6 h in a pack containing 10%Al+5%NaF+85%Al2O3 in mass traction.The aluminized layers formed on the samples were characterized.The kinetic studies indicated that the diffusion of Al-bearing gases through the pack is the rate-controlling step in this process.The activation energy of 161.8 kJ/mol was calculated for this step.In addition,the mass gains of the aluminized samples were predicted using the partial pressures of gases in the pack and those adjacent to the samples surface.The predicted values are in good agreement wim the experimental measurements at 950 ℃ but are higher than those measured at 1025 and 1100 ℃.
文摘Aluminizing of Cu by a pack cementation process was performed to improve its surface properties.The effect of variation of pack aluminizing temperature from 800 to 900℃ and aluminizing time from 1 to 6 h on the microstructure and the thickness of the aluminide coating of Cu was investigated. Pack aluminizing of Cu significantly improved the microhardness and the oxidation resistance. The microhardness was increased about seven times and the oxidation resistance,after 96 h exposure in air at 900℃, was extremely increased ten times by aluminizing Cu at 900℃ for 3 h.
基金Iraqi International Center for Science and Industry (IICSI, 2005-1)
文摘IN 600 alloy was coated with two different types of coatings, Cr-modified aluminide coating this is called aluminizing-chromizing and Y-doped chromium modified aluminide coating this is called aluminizing-chromizing-yttriumizing. Diffusion coating was carried at 1 050℃ for 8 h under Ar atmosphere by simultaneous aluminizing-chromizing process and by simultaneous aluminizing-chromizing- yttriumizing. Cyclic oxidation tests were conducted on the uncoated and on the coated Inconel 600 alloy in the temperature range 800- 1 000℃ in CO2 for 100 h at 10 h cycle.The results showed that the oxidation kinetics for uncoated Inconel 600 alloy in CO2 is parabolic and the phases present are NiO, (Fe, Cr)2O3 , NiFe2O4 and NiCrO4. The oxidation kinetics for both coated systems in CO2 was found to be parabolic and the value ofkp for both coated systems were found to be lower than that for uncoated Inconel 600 alloy. Oxide phases that formed on coated systems are Al2O3 and NiCrO4. The role of yttrium can be attributed to its ability to improve the adherence of the oxide scale.
文摘The steel surface treatment by rare-earth aluminithermic aluminizing,which was utilized onthermal couple,buried parts of lightning arrester and silencer of automobile,has met with success.This new technique was studied by Beijing University of Science and Technology,BeijingIron-steel Institute and Jingdong Work of Corrosion-protective Materials cooperatively.The steel
基金Funded by National Natural Science Foundation of China(Nos.51772212,51402216,51978505)。
文摘This paper describes a study on the corrosion behavior of steel reinforcement in CAC mortars via electrochemical methods including corrosion potential,electrochemical impedance,and linear polarization evaluation.Results indicate that there is a non-linear relationship between the corrosion degree of steel reinforcement in CAC mortar and the concentration of NaCl solution.The electrochemical parameters of specimens immersed in 3%NaCl solution suddenly drop at 40 days,earlier than 60 days of the reference.And the charge transfer resistivity of the specimen has decreased by 11 orders of magnitude at 40 days,showing an evident corrosion on steel reinforcement.However,it is interesting to notice that the corrosion is delayed by high external chloride concentration.The specimens immersed in 9%and 15%NaCl solutions remain in a relatively stable state within 120 days with slight pitting.The great corrosion protection of CAC concrete to embedded steel bars enables its wide application in marine.
基金acknowledged DEQ/IT/UFRRJ,FEG/UNESP-Guaratinguetáand EEL/USP-Lorena for their support in carrying out the analyses.
文摘Aluminous refractory materials with high alumina contents are widely used in the steel industry,and the higher the alumina content,the higher the working temperature.Properties such as high refractoriness and thermal shock resistance lead these refractory materials to be used as channel linings of blast furnaces,where they are exposed to the attack by slag,molten steel,working cycles and sudden temperature changes between 25℃(room temperature)and 1520℃(the temperature of molten pig iron).In this work,microstructural changes in post-mortem aluminous refractory bricks were investigated by apparent porosity,X-ray diffraction analysis(XRD),Fourier transform infrared spectroscopy(FTIR),scanning electron microscopy,and X-ray dispersion energy spectrometry(SEM/EDS).The results showed an increase in the apparent porosity and the bulk density and the presence of the phases mullite,sillimanite,alumina,and quartz in the post-mortem brick.Calcium and magnesium were not detected in the microstructure of the post-mortem brick,indicating that slags did not corrode these refractory materials.Therefore,the microstructural changes that occurred in the post-mortem bricks must be due to thermal cycling.In the X-ray diffraction(XRD)test,mullite,sillimanite,quartz,andα-alumina phases were identified.These results indicate that the aluminous refractory was obtained from sillimanite.In infrared spectroscopy(FTIR)it was possible to identify the vibration bands referring to the Si-O and Al-O bonds.The increase in the porosity is a result of cracks caused by work cycles at high temperatures and the temperature gradient to which the refractory was subjected during use.Through the micrograph it was possible to identify the presence of acicular mullite.The absence of magnesium and calcium in the microanalysis results by energy dispersed X-ray spectrometry(EDS)indicates that there was no infiltration by slag or liquid iron.These results indicate that the microstructural changes that occurred in the post-mortem aluminous refractory were of a thermal nature.
基金Funded by the National Natural Science Foundation of China(Nos.52278275 and 52202029)the Major Technical Innovation Project in Hubei Province of China(No.2021BAA060)。
文摘To improve the efficiency and stability of chloride immobilization of portland cement paste,hydrated calcium aluminate cement(HCAC)prepared by wet grinding of CAC was added into portland cement paste as an additive.The immobilized chloride ratio(ICR)was evaluated,and the mechanism of chloride immobilization was researched by XRD,DTG,NMR,and MIP tests.The analysis results demonstrated that HCAC could improve the chloride immobilization capacity of portland cement paste.The mechanism was attributed to the following aspects:chemical binding capacity was enhanced via producing more Kuzel’s salt;physical adsorption capacity was reduced by decreasing the C-S-H gel;migration resistance was enhanced through refining the pore structure.
基金Zhongyuan Science and Technology Innovation Leading Talents(224200510006)NSFC-Henan Joint Fund funded project(U1904217).
文摘In order to enhance the sintering resistance of lanthanum aluminate based high emissivity coatings,Ca^(2+)-Fe^(3+)doped LaAlO_(3)/ZrO_(2)specimens were prepared by solid state sintering using La_(2)O_(3),Al_(2)O_(3),CaCO_(3) and Fe_(2)O_(3) as raw materials,extra-adding fused Y_(2)O_(3)-stabilized ZrO_(2)(0,5%,10%,and 15%,by mass),ball milling,pre-calcining,pressing into shapes and sintering at 1600℃for 2 h.The effect of the ZrO_(2)addition on the properties of lanthanum aluminate based high emissivity coatings was explored.It is concluded that ZrO_(2)does not react with LaAlO_(3),which can inhibit the sintering of the specimens.With the increase of the ZrO_(2),addition,the linear shrinkage rate and the thermal conductivity decrease significantly,while the emissivity decreases,but the emissivity of all the specimens is all higher than 0.9.The optimal addition of ZrO_(2),is 10%.
文摘Unburned magnesium aluminate spinel refractories were prepared using sintered magnesium aluminate spinel as the main raw material,phenolic resin as the binder,aluminum powder(2%,4%,and 6%by mass)and silicon powder(when Al powder addition is 4%,Si powder addition varies:1%and 2%,by mass)as additives.The effects of the Al powder and Si powder additions on the properties and microstructure of the refractories heat treated at different temperatures(1000,1400,and 1600℃for 3 h)were studied.The results show that the Al powder addition can greatly enhance the cold modulus of rupture of the samples fired at 1000 or 1400℃,and meanwhile AlN reinforcement phase forms in the matrix,which greatly improves the hot modulus of rupture of the samples at 1400℃;however,the heat treatment at 1600℃has little influence on the strength;the addition of Al powder and Si powder results in the formation of low melting point phases,greatly reducing the hot modulus of rupture.However,the low melting point phases promote sintering,which enhances the density and the cold modulus of rupture,and decreases the volume change during heating.The samples added with Al and Si all have higher cold modulus of rupture than those added with Al powder only.
基金supported by the National Natural Science Foundation of China(No.52279138)supported by Scientific Research Project of Shanxi Province(2018SF-367).
文摘The adsorption method has the advantages of low cost,high efficiency,and environmental friendliness in treating fluorinated wastewater,and the adsorbent material is the key.This study combines the inherent anion-exchange adsorption properties of layered double hydroxides(LDHs).Self-supported porous adsorbent materials loaded with AFm and AFt were prepared from a composite cementitious system consisting of calcium aluminate cement(CAC)and flue gas desulfurization gypsum(FGDG)by chemical foaming technique.The mineral composition of the adsorbent material was characterized by X-ray diffraction(XRD)and Scanning electron microscopy(SEM).Through the static adsorption experiment,the adsorption effect of the mineral composition of the adsorbent on fluoride ions was deeply analyzed,and the adsorption mechanism was revealed.XRD and SEM showed that the main hydration phases of the composite cementitious system consisting of CAC and FGDG are AFm,AFt,AH_(3),and CaSO_(4)·2H_(2)O.FGDG accelerates the hydration process of CAC and inhibits the transformation of AFt to AFm.The AFt content increased,and the AFm content decreased or even disappeared as the amount of FGDG increased.Static adsorption experiment results showed that AFm and AFt in adsorbent materials could significantly enhance the adsorption of fluoride ions.The adsorption of F^(−)in aqueous solution by PAG tends more towards monolayer adsorption with a theoretical maximum capacity of 108.70 mg/g and is similar to the measured value of 112.77 mg/g.
基金Project(0511021600) supported by the Natural Science Foundation of Henan Province, China
文摘The RE-aluminized coating and pure aluminized coating on 20 carbons steel were prepared by hot dip aluminizing method at 740℃. After diffusion treatment at 850℃for 4 h, the distribution of aluminum and lanthanum elements in the coating was analyzed with energy disperse spectroscopy(EDS) and electron probe microanalyses(EPMA), and the lattice parameter ofα-Fe in the matrix of the coating was measured precisely by X-ray diffractometer(XRD). The results show that RE permeates into the aluminized coating, leads to lattice disturbance and increases the depth of the aluminized coating. On the basis of the results, the expression of the diffusion coefficient of Al atoms is derived from the diffusion flow, and the effect of the high vacancy concentration and high concentration gradient of vacancies on the diffusion of Al atoms was analyzed by establishing the kinetics model of the vacancy mechanism of diffusion. The results show that the high vacancy concentration and high concentration gradient of vacancies in the RE-aluminized processes are the main reason why the diffusion coefficient of Al atoms in RE-aluminizing is bigger than that in pure aluminizing.