Effects of nitrogen on ozone synthesis in packed-bed dielectric barrier discharge

The effects of nitrogen on ozone synthesis are studied in a coaxial cylinder generator with dielectric barrier discharge（DBD） and pack-bed dielectric barrier discharge（PB-DBD）.A series of 10 h discharge experiments are conducted adopting a bare stainless electrode and bare copper electrode.Results show that the material of the electrode can affect the ozone synthesis.It is inferred that the ozone zero phenomenon（OZP） may be induced from ozone decomposing by metallic oxide catalysis.Packing dielectric particles can reduce the OZP.Adding a certain amount of nitrogen into the oxygen feed gas can further eliminate the OZP,and increase the ozone concentration significantly,but decreases the maximum energy efficiency of ozone generators.Initial analysis indicates that the optimal proportion of nitrogen addition is inversely related to the average reduced electric field strength in the discharge region.

Plasma-assisted ammonia synthesis in a packed-bed dielectric barrier discharge reactor:roles of dielectric constant and thermal conductivity of packing materials

In this article,plasma-assisted NH;synthesis directly from N;and H;over packing materials with different dielectric constants(BaTiO_(2),TiO_(2) and SiO_(2))and thermal conductivities(Be O,Al N and Al_(2)O_(2))at room temperature and atmospheric pressure is reported.The higher dielectric constant and thermal conductivity of packing material are found to be the key parameters in enhancing the NH;synthesis performance.The NH;concentration of 1344 ppm is achieved in the presence of BaTiO_(2),which is 106%higher than that of SiO_(2),at the specific input energy(SIE)of 5.4 k J·l^(-1).The presence of materials with higher dielectric constant,i.e.BaTiO_(2) and TiO_(2)in this work,would contribute to the increase of electron energy and energy injected to plasma,which is conductive to the generation of chemically active species by electron-impact reactions.Therefore,the employment of packing materials with higher dielectric constant has proved to be beneficial for NH;synthesis.Compared to that of Al_(2)O_(3),the presence of Be O and Al N yields 31.0%and 16.9%improvement in NH;concentration,respectively,at the SIE of5.4 k J·l^(-1).The results of IR imaging show that the addition of Be O decreases the surface temperature of the packed region by 20.5%to 70.3℃ and results in an extension of entropy increment compared to that of Al_(2)O_(3),at the SIE of 5.4 k J·l^(-1).The results indicate that the presence of materials with higher thermal conductivity is beneficial for NH;synthesis,which has been confirmed by the lower surface temperature and higher entropy increment of the packed region.In addition,when SIE is higher than the optimal value,further increasing SIE would lead to the decrease of energy efficiency,which would be related to the exacerbation in reverse reaction of NH;formation reactions.

Experimental study on the parameter optimization and application of a packed-bed dielectric barrier discharge reactor in diesel particulate filter regeneration

To compensate for the shortcomings of the thermal and catalytic regeneration of the diesel particulate filter(DPF),a self-designed packed-bed dielectric barrier discharge(DBD)reactor for DPF regeneration was developed.The DBD reactor with the main active substance of nonthermal plasma(NTP)as the target parameter was optimized by adjusting the feed gas,packing particles(material or size),and cooling water temperature.Moreover,a set of optimal working parameters(gas source,O_2;packing particles,1.2–1.4 mm ZrO_(2);and cooling water temperature,20℃)was selected to evaluate the effect of different O_(3) concentrations on DPF regeneration.The research results showed that selecting packing particles with high dielectric constant and large particles,as well as reducing the cooling water temperature,with oxygen as the feed gas,contributed to an increase in O_(3) concentration.During DPF regeneration,the following changes were observed:the power of the NTP reactor decreased to lower than 100 W,the O_(3) concentration increased from 15 g m^(-3) to 45 g m^(-3),the CO and CO_2 volume fractions of the particulate matter decomposition products increased,and the peak regeneration temperature increased to 173.4℃.The peak temperature arrival time was 60 min earlier,indicating that the regeneration rate of DPF increased with the increase in O_(3) concentration.However,the O_(3) utilization rate(the amount of carbon deposit removed per unit volume O_(3))initially increased and then decreased;when the O_(3) concentration was set to 25 g m^(-3),the highest O_(3) utilization rate was reached.The packed-bed DBD technology contributed to the increase in the concentration of NTP active substances and the regeneration efficiency of DPF.It provides a theoretical and experimental basis for high-efficiency regeneration of DPF at low temperatures(<200℃).

Effect of dielectric material on the uniformity of nanosecond pulsed dielectric barrier discharge

Dielectric barrier discharge(DBD)is considered as a promising technique to produce large volume uniform plasma at atmospheric pressure,and the dielectric barrier layer between the electrodes plays a key role in the DBD processes and enhancing discharge uniformity.In this work,the uniformity and discharge characteristics of the nanosecond(ns)pulsed DBD with dielectric barrier layers made of alumina,quartz glass,polycarbonate(PC),and polypropylene(PP)are investigated via discharge image observation,voltage-current waveform measurement and optical emission spectral diagnosis.Through analyzing discharge image by gray value standard deviation method,the discharge uniformity is quantitatively calculated.The effects of the space electric field intensity,the electron density(Ne),and the space reactive species on the uniformity are studied with quantifying the gap voltage Ug and the discharge current Ig,analyzing the recorded optical emission spectra,and simulating the temporal distribution of Ne with a one-dimensional fluid model.It is found that as the relative permittivity of the dielectric materials increases,the space electric field intensity is enhanced,which results in a higher Ne and electron temperature(Te).Therefore,an appropriate value of space electric field intensity can promote electron avalanches,resulting in uniform and stable plasma by the merging of electron avalanches.However,an excessive value of space electric field intensity leads to the aggregation of space charges and the distortion of the space electric field,which reduce the discharge uniformity.The surface roughness and the surface charge decay are measured to explain the influences of the surface properties and the second electron emission on the discharge uniformity.The results in this work give a comprehensive understanding of the effect of the dielectric materials on the DBD uniformity,and contribute to the selection of dielectric materials for DBD reactor and the realization of atmospheric pressure uniform,stable,and reactive plasma sources.

On the evolution and formation of discharge morphology in pulsed dielectric barrier discharge

The discharge morphology of pulsed dielectric barrier discharge(PDBD) plays important roles in its applications. Here, we systematically investigated the effects of the voltage amplitude,discharge gap, and O_(2)content on the PDBD morphology, and revealed the possible underlying mechanism of the U-shaped formation. First, the morphological evolution under different conditions was recorded. A unique U-shaped region appears in the middle edge region when the gap is larger than 2 mm, while the entire discharge region remains columnar under a 2 mm gap in He PDBD. The width of the discharge and the U-shaped region increase with the increase in voltage, and decrease with the increase of the gap and O_(2)content. To explain this phenomenon,a two-dimensional symmetric model was developed to simulate the spatiotemporal evolution of different species and calculate the electric thrust. The discharge morphology evolution directly corresponds to the excited-state atomic reduction process. The electric thrust on the charged particles mainly determines the reaction region and strongly influences the U-shaped formation.When the gap is less than 2 mm, the electric thrust is homogeneous throughout the entire region,resulting in a columnar shape. However, when the gap is larger than 2 mm or O_(2)is added, the electric thrust in the edge region becomes greater than that in the middle, leading to the U-shaped formation. Furthermore, in He PDBD, the charged particles generating electric thrust are mainly electrons and helium ions, while in He/O_(2)PDBD those that generate electric thrust at the outer edge of the electrode surface are mainly various oxygen-containing ions.

Experimental study on the effect of H_(2)O and O_(2) on the degradation of SF_(6) by pulsed dielectric barrier discharge

SF_(6) has excellent insulation performance and arc extinguishing ability,and is widely used in the power industry.However,its global warming potential is about 23,500 times that of C0_(2),it can exist stably in the atmosphere,it is not easily degradable and is of great potential harm to the environment.Based on pulsed dielectric barrier discharge plasma technology,the effects of H_(2)O and 0_(2) on the degradation of SF_(6) were studied.Studies have shown that H_(2)O can effectively promote the decomposition of SF_(6) and improve its degradation rate and energy efficiency of degradation.Under the action of a pulse input voltage and input frequency of 15 kV and 15 kHz,respectively,when H_(2)O is added alone the effect of 1% H_(2)O is the best,and the rate and energy efficiency of degradation of SF_(6) reach their maximum values,which are 91.9% and 8.25 g kWh^(-1),respectively.The synergistic effect of H_(2)O and O_(2) on the degradation of SF_(6) was similar to that of H_(2)O.When the concentration of H_(2)O and O_(2) was 1%,the system obtained the best rate and energy efficiency of degradation,namely 89.7% and 8.05 g kWh~(-1),respectively.At the same time,different external gases exhibit different capabilities to regulate decomposition products.The addition of H_(2)O can effectively improve the selectivity of S0_(2).Under the synergistic effect of H_(2)O and O_(2),with increase in O_(2) concentration the degradation products gradually transformed into SO_(2)F_(2).From the perspective of harmless treatment of the degradation products of SF_(6),the addition of O_(2) during the SF_(6) degradation process should be avoided.

Surface charge characteristics in a three-electrode surface dielectric barrier discharge

The surface charge characteristics in a three-electrode surface dielectric barrier discharge(SDBD)are experimentally investigated based on the Pockels effect of an electro-optical crystal. The actuator is based on the most commonly used SDBD structure for airflow control, with an exposed electrode supplied with sinusoidal AC high voltage, a grounded encapsulated electrode and an additional exposed electrode downstream supplied with DC voltage. The ionic wind velocity and thrust can be significantly improved by increasing DC voltage although the plasma discharge characteristics are virtually unaffected. It is found that the negative charges generated by the discharge of the three-electrode structure accumulate on the dielectric surface significantly further downstream in an AC period compared to the actuator with a two-electrode structure. The negative charges in the downstream region increase as the DC voltage increases.In addition, the DC voltage affects the time required for the positive charge filaments to decay.The positive DC voltage expands the ionic acceleration zone downstream to produce a greater EHD force. The amplitude of the DC voltage affects the electric field on the dielectric surface and is therefore a key factor in the formation of the EHD force. Further research on the surface charge characteristics of a three-electrode structure has been conducted using a pulse power to drive the discharge, and the same conclusions are drawn. This work demonstrates a link between surface charge characteristics and EHD performance of a three-electrode SDBD actuator.

Single flow treatment degradation of antibiotics in water using falling-film dielectric barrier discharge

The environmental contamination caused by antibiotics is increasingly conspicuous due to their widespread manufacture and misuse. Plasma has been employed in recent years for the remediation of antibiotic pollution in the environment. In this work, a falling-film dielectric barrier discharge was used to degrade the antibiotic tetracycline(TC) in water. The reactor combined the gas-liquid discharge and active gas bubbling to improve the TC degradation performance. The discharge characteristics, chemical species’ concentration, and degradation rates at different parameters were systematically studied. Under the optimized conditions(working gas was pure oxygen, liquid flow rate was 100 mL/min, gas flow rate was 1 L/min,voltage was 20 kV, single treatment), TC was removed beyond 70% in a single flow treatment with an energy efficiency of 145 mg/(kW·h). The reactor design facilitated gas and liquid flow in the plasma area to produce more ozone in bubbles after a single flow under pure oxygen conditions, affording fast TC degradation. Furthermore, long-term stationary experiment indicated that long-lived active species can sustain the degradation of TC. Compared with other plasma treatment systems, this work offers a fast and efficient degradation method, showing significant potential in practical industrial applications.

Reconfigurable(4, 6^(2)) and(4, 8^(2)) Archimedean plasma photonic crystals in dielectric barrier discharge

Archimedean photonic crystal has become a research area of great interest due to its various unique properties. Here, we experimentally demonstrate the realization of reconfigurable(4, 6^(2))and(4, 8^(2)) Archimedean plasma photonic crystals(APPCs) by use of dielectric barrier discharges in air. Dynamical control on both the macrostructures including the lattice symmetry and the crystal orientation, and the microstructures including the fine structures of scattering elements has been achieved. The formation mechanisms of APPCs are studied by time-resolved measurements together with numerical simulations. Large omnidirectional band gaps of APPCs have been obtained. The tunable topology of APPCs may offer new opportunities for fabricating multi-functional and highly-integrated microwave devices.

Formation mechanism of bright and dark concentric-ring pattern in dielectric barrier discharge

In this work,a bright and dark concentric-ring pattern is reported in a dielectric barrier discharge for the first time.The spatiotemporal dynamics of the bright and dark concentric-ring pattern are investigated with an intensified charge-coupled device and photomultiplier tubes.The results indicate that the bright and dark concentric-ring pattern is composed of three concentric-ring sublattices.These are bright concentric-ring structures,dark concentric-ring structures and wider concentric-ring structures,respectively.The bright concentric-ring structures and dark concentricring structures are alternately distributed.The bright concentric-ring structures are located at the centre of the wider concentric-ring structures.The wider concentric-ring structures first form from the outer edge and gradually develop to the centre.The essence of all three concentric-ring structures is the individual discharge filaments.The optical emission spectra of different sublattices are acquired and analysed.It is found that the plasma parameters of the three concentricring sublattices are different.Finally,the formation mechanism of the bright and dark concentricring pattern is discussed.

Improving the energy efficiency of surface dielectric barrier discharge devices for plasma nitric oxide conversion utilizing active flow control

Improving energy efficiency in plasma NO removal is a critical issue.When the surface dielectric barrier discharge(SDBD)device is considered as a combination of multiple plasma actuators,the induced plasma aerodynamic effect cannot be ignored,which can affect the mass transfer,then affect the chemical reactions.Five SDBD devices with different electrode arrangements are studied for NO conversion.They correspond to different flow patterns.We find that the energy efficiency in an SDBD device with a common structure(Type 1)is 28%lower than that in SDBD devices with a special arrangement(Types 2–5).Two reasons may explain the results.First,fewer active species are produced in Type 1 because the development of discharge is hindered by the mutually exclusive electric field forces caused by the symmetrically distributed charged particles.Second,the plasma wind induced by the plasma actuator can enhance the mass and heat transfer.The mixing of reactants and products is better in Types 2–5 than Type 1 due to higher turbulence kinetic energy.

Realization of homogeneous dielectric barrier discharge in atmospheric pressure argon and the effect of beads on its characteristics

This paper describes the realization of a homogeneous dielectric barrier discharge(DBD)in argon at atmospheric pressure.The effect of the morphology of the dielectric surface(especially the dielectric surface covered by hollow ceramic beads(99%Al_(2)O_(3))with different diameters)on discharge is investigated.With different dielectrics,the argon DBD presents two discharge modes:a filamentary mode and a homogeneous mode.Fast photography shows that the filamentary mode operates in a streamer discharge,and the homogeneous mode operates in a Townsend discharge regime.It is found that a homogeneous discharge can be generated within a certain voltage range.The voltage amplitude range decreases,and the breakdown voltage increases with the increase in the mean diameter of the ceramic beads.Waveforms of the total current and optical emission signal present stochastic pulses per half voltage cycle for the filamentary mode,whereas there is one single hump per half voltage cycle for the homogeneous mode.In the homogeneous mode,the intensity of the optical emission decreases with the mean diameter of the ceramic beads.The optical emission spectrum is mainly composed of atomic lines of argon and the second positive system of molecular nitrogen.It reveals that the electron density decreases with the increasing mean diameter of the ceramic beads.The vibrational temperature increases with the increasing mean diameter of the ceramic beads.It is believed that a large number of microdischarges are formed,and smaller ceramic beads have a larger activation surface area and more point discharge.Electrons liberated in the shallow well and electrons generated from microdischarges can increase the secondary electron emission coefficient of the cathode and provide initial electrons for discharge continuously.Therefore,the breakdown electric field is reduced,which contributes to easier generation of homogeneous discharge.This is confirmed by the simulation results.

Square grid pattern with direction-selective surface discharges in dielectric barrier discharge

A new phenomenon that a filament discharged only once instead of twice in a cycle of the applied voltage is observed in a square grid pattern in a dielectric barrier discharge(DBD)with a larger gas gap,which is named intermittent discharge.Its spatiotemporal dynamics and the formation mechanism are studied by the multiple photomultiplier tubes and an intensified charge-coupled device.Corresponding to the positions of spots in the picture with an exposure time of 40 ms,there are some bright spots(discharge spots)and black spots(non-discharged spots)in the instantaneous image with an exposure time of 10μs(a half cycle of the applied voltage).There are at least two bright spots around one black spot and vice versa.The surface discharges(SDS)can be observed between any two adjacent spots.The intensity of the SDSbetween the bright spot and the black spot is 2.5 times greater than that between two adjacent bright spots,which indicates that the SDSare directional-selective.The intermittent discharge with positive(negative)current polarity changes to that with negative(positive)current polarity,after it sustains up to 14 voltage cycles at the longest.The spatial distribution of the electric field component is calculated through COMSOL software to solve the Poisson equation numerically.It is found that the inhomogeneous distribution of surface electric field is caused by the inhomogeneous distribution of wall charges,which leads to direction-selective SDS.The intermittent discharge is formed by the competition between the direction-selective SDSand volume discharges(VDS)in DBD.This is the reason why the intermittent discharge is generated.

Rotor performance enhancement by alternating current dielectric barrier discharge plasma actuation

An experimental system was established to explore the plasma flow control effect for helicopter rotors in hover mode.With the plasma actuator applied at the leading edge of the rotor blades,alternating current dielectric barrier discharge(AC-DBD) plasma actuation was generated by a sinusoidal AC high-voltage generator.By direct force measurement,the influence of actuation parameters on the aerodynamic performance of the rotor was investigated at a tip Reynolds number of 1.7 × 105.AC-DBD actuation can delay the blade stall to more than 3° with a 20%increase of about in the thrust coefficient at the post-stall pitch.At a constant motor power driving the rotor,AC-DBD actuation could reduce the rotor’s torque at the stalled pitch and increase the rotational speed of the rotor.Also,AC-DBD actuation could maintain a relatively high hover efficiency of the rotor at large collective pitches.In a wide range of actuation parameters,AC-DBD plasma actuation could improve the rotor’s aerodynamic performance at large blade pitches.High-speed photography of the tuft motion on the blade’s upper surface showed that AC-DBD plasma actuation could promote the reattachment of the blade’s separation flow.

Experimental and numerical investigation on the uniformity of nanosecond pulsed dielectric barrier discharge influenced by pulse parameters

Nanosecond(ns)pulsed dielectric barrier discharge(DBD)is considered as a promising method to produce controllable large-volume and high activity low-temperature plasma at atmospheric pressure,which makes it suitable for wide applications.In this work,the ns pulse power supply is used to excite Ar DBD and the influences of the pulse parameters(voltage amplitude,pulse width,pulse rise and fall times)on the DBD uniformity are investigated.The gas gap voltage(Ug)and conduct current(Ig)are separated from the measured voltage and current waveforms to analyze the influence of electrical parameters.The spectral line intensity ratio of two Ar excited species is used as an indicator of the electron temperature(Te).The time resolved discharge processes are recorded by an intensified charge-coupled device camera and a one-dimensional fluid model is employed to simulate the spatial and temporal distributions of electrons,ions,metastable argon atoms and Te.Combining the experimental and numerical results,the mechanism of the pulse parameters influencing on the discharge uniformity is discussed.It is shown that the space electric field intensity and the space particles'densities are mainly responsible for the variation of discharge uniformity.With the increase of voltage and pulse width,the electric field intensity and the density of space particles increased,which results in the discharge mode transition from non-uniform to uniform,and then non-uniform.Furthermore,the extension of pulse rise and fall times leads to the discharge transition from uniform to nonuniform.The results are helpful to reveal the mechanism of ns pulsed DBD mode transition and to realize controllable and uniform plasma sources at atmospheric pressure.

Numerical simulation study of ionization characteristics of argon dielectric barrier discharge

In order to better analyze the characteristics of particle distribution and its influencing factors in the ionized space during the process of coaxial dielectric barrier discharge,a self-designed two-dimensional axisymmetric structure exciter was used to carry out optical diagnosis,with the electron temperature calculated through Gaussian fitting.A plasma model was applied to conduct research on the discharge process through numerical simulation,with the changes in electron density and electron temperature were analyzed by using different discharge parameters.The research results show that with an increase in discharge voltage,pressure inside the reactor and relative permittivity,the discharge process is promoted.In addition,a rise in current density leads to an increase in the number of charged particles on the surface of the medium during the discharge process,while a rise in discharge intensity causes an increase in the electron density.Electron temperature decreases due to the increased loss of collision energy between particles.These results were confirmed by comparing experimental data with simulation results.

Controllable and tunable plasma photonic crystals through a combination of photonic crystal and dielectric barrier discharge patterns

We report five types of patterns with square symmetry,including three novel types obtained by inserting a specially designed grid photonic crystal(PC)into a dielectric barrier discharge system.They are studied using an intensified charge-coupled device camera and photomultiplier tubes.The three novel types of patterns are a square pattern with one structure,a square superlattice pattern with four sublattices and a(1/4)K_(grid)(K_(grid)is the basic wave vector of the grid),and another square pattern with a complex inversion discharge sequence.From the application viewpoint,the five types of patterns can be used as plasma photonic crystals(PPCs).Their band diagrams under a transverse-magnetic wave simulated by the finite element method show that there are a large number of band gaps.Compared with the original PC with only a unidirectional band gap,the five types of PPCs have tunable and omnidirectional band gaps,which is very important in controlling the propagation of electromagnetic waves in the mm-wave region.The experimental results enrich the pattern types in the dielectric barrier discharge system and provide a method for obtaining PPCs with symmetry controllability and bandgap tunability.

NaCl aqueous solution as a novel electrode in a dielectric barrier discharge reactor for highly efficient ozone generation

Ozone(O_(3)) generated by a dielectric barrier discharge(DBD) is widely used in various industrial processes. In this study, NaCl aqueous solution was used as a novel electric power transmission electrode in a DBD reactor(instead of a traditional metal electrode) for highly efficient ozone generation. The results demonstrated that a high O_(3) yield of 242 g k Wh^(-1) with a concentration of 14.6 g m^(-3)O_(3) was achieved. The power transmission mechanism works because NaCl aqueous solution behaves as a capacitor when an alternating pulse voltage below 8 k Hz is used.Compared with the resistance of the discharge barrier and discharge space, the resistance of NaCl aqueous solution can be ignored, which ensures that O_(3) is generated efficiently. It is expected that O_(3) generation using NaCl aqueous solution as a novel electrode in a DBD reactor could be an alternative technology with good application prospects.

Degradation of sulfamethoxazole in water by dielectric barrier discharge plasma jet:influencing parameters,degradation pathway,toxicity evaluation

Sulfamethoxazole(SMX)is an antibiotic and widely present in aquatic environments,so it presents a serious threat to human health and sustainable development.A dielectric barrier discharge(DBD)plasma jet was utilized to degrade aqueous SMX,and the effects of various operating parameters(working gas,discharge power,etc)on SMX degradation performance were studied.The experimental results showed that the DBD plasma jet can obtain a relatively high degradation efficiency for SMX when the discharge power is high with an oxygen atmosphere,the initial concentration of SMX is low,and the aqueous solution is under acidic conditions.The reactive species produced in the liquid phase were detected,and OH radicals and O3were found to play a significant role in the degradation of SMX.Moreover,the process of SMX degradation could be better fitted by the quasi-first-order reaction kinetic equation.The analysis of the SMX degradation process indicated that SMX was gradually decomposed and 4-amino benzene sulfonic acid,benzene sulfonamide,4-nitro SMX,and phenylsulfinyl acid were detected,and thus three possible degradation pathways were finally proposed.The mineralization degree of SMX reached 90.04%after plasma treatment for 20 min,and the toxicity of the solution fluctuated with the discharge time but eventually decreased.

Wet flashover voltage improvement of the ceramics with dielectric barrier discharge

Surface modification techniques with plasma are widely investigated to improve the surface insulation capability of polymers under dry conditions,while the relationship between treatment method,surface physical and chemical properties,and wet flashover voltage is still unclear for inorganic ceramics.In this work,the surface insulation properties of ceramics under wet conditions are improved using nanosecond-pulsed dielectric barrier discharge with polydimethylsiloxane(PDMS)as the precursor.The relationships between PDMS concentration and the water contact angle,dry and wet flashover voltages are obtained to acquire the optimal concentration.The surface charge dissipation test and surface physio-chemical property measurement with SEM,AFM,XPS are carried out to further explore the mechanism of surface insulation enhancement.The results show that film deposition with micron thickness and superhydrophobicity occurs at the PDMS concentration of 1.5%.The dry flashover voltage is increased by 14.6%due to the induction of deep traps,while the wet flashover voltage is increased by 66.7%.The gap between dry-wet flashover voltage is decreased by 62.3%compared with the untreated one due to the self-cleaning effect.