Solving single-frequency phase ambiguity using parameter weights fitting and constrained equation ambiguity resolution methods

Based on the structural characteristics of the double-differenced normal equation, a new method was proposed to resolve the ambiguity float solution through a selection of parameter weights to construct an appropriate regularized matrix, and a singular decomposition method was used to generate regularization parameters. Numerical test results suggest that the regularized ambiguity float solution is more stable and reliable than the least-squares float solution. The mean square error matrix of the new method possesses a lower correlation than the variancecovariance matrix of the least-squares estimation. The size of the ambiguity search space is reduced and the search efficiency is improved. The success rate of the integer ambiguity searching process is improved significantly when the ambiguity resolution by using constraint equation method is used to determine the correct ambiguity integervector. The ambiguity resolution by using constraint equation method requires an initial input of the ambiguity float solution candidates which are obtained from the LAMBDA method in the new method. In addition, the observation time required to fix reliable integer ambiguities can he significantly reduced.

Numerical and experimental evaluation on methods for parameter identification of thermal response tests

Several parameter identification methods of thermal response test were evaluated through numerical and experimental study.A three-dimensional finite-volume numerical model was established under the assumption that the soil thermal conductivity had been known in the simulation of thermal response test.The thermal response curve was firstly obtained through numerical calculation.Then,the accuracy of the numerical model was verified with measured data obtained through a thermal response test.Based on the numerical and experimental thermal response curves,the thermal conductivity of the soil was calculated by different parameter identification methods.The calculated results were compared with the assumed value and then the accuracy of these methods was evaluated.Furthermore,the effects of test time,variable data quality,borehole radius,initial ground temperature,and heat injection rate were analyzed.The results show that the method based on cylinder-source model has a low precision and the identified thermal conductivity decreases with an increase in borehole radius.For parameter estimation,the measuring accuracy of the initial temperature of the deep ground soil has greater effect on identified thermal conductivity.

Downward continuation of airborne geomagnetic data based on two iterative regularization methods in the frequency domain

Downward continuation is a key step in processing airborne geomagnetic data. However,downward continuation is a typically ill-posed problem because its computation is unstable; thus, regularization methods are needed to realize effective continuation. According to the Poisson integral plane approximate relationship between observation and continuation data, the computation formulae combined with the fast Fourier transform（FFT）algorithm are transformed to a frequency domain for accelerating the computational speed. The iterative Tikhonov regularization method and the iterative Landweber regularization method are used in this paper to overcome instability and improve the precision of the results. The availability of these two iterative regularization methods in the frequency domain is validated by simulated geomagnetic data, and the continuation results show good precision.

Evaluation of Some Weibull Parameter Estimation Methods for Characterizing Stem Diameter Distribution in a Tropical Mixed Forest of Southern Nigeria

Stem diameter distribution information is useful in forest management planning. Weibull function is flexible, and has been used in characterising diameter distributions, especially in single-species planted stands, the world over. We evaluated some Weibull parameter estimation methods for stem diameter characterisation in （Oban） multi-species Forest in southern Nigeria. Four study sites （Aking, Ekang, Erokut and Ekuri） were selected. Four 2 km-long transects situated at 600 m apart were laid in each location. Five 50m x 50m plots were alternately laid along each transect at 400 m apart （20 plots/location） using systematic sampling technique. Tree growth variables： diameter at breast height （Dbh）, diameters at the base, middle and merchantable limit, total height, merchantable height, stem straightness, crown length and crown diameter were measured on all trees 〉 10 cm to compute model response variables such as mean diameters, basal area and stem volume. Weibull parameters estimation methods used were： moment-based, percentile-based, hybrid and maximum-likelihood （ML）. Data were analysed using descriptive statistics, regression models and ANOVA at α0.05. Percentile-based method was the best for Weibull [location （a）, scale （b） and shape （c）] parameters estimations with mLogL = 116.66±21.89, while hybrid method was least-suitable （mLogL = 690.14±128.81） for Weibull parameters estimations. Quadratic mean diameter （Dq） was the only suitable predictor of Weibull parameters in Oban Forest.

Topology Optimization for Steady-State Navier-Stokes Flow Based on Parameterized Level Set Based Method

In this paper,we consider solving the topology optimization for steady-state incompressibleNavier-Stokes problems via a new topology optimization method called parameterized level set method,which can maintain a relatively smooth level set function with a local optimality condition.The objective of topology optimization is to􀀀nd an optimal con􀀀guration of theuid and solid materials that minimizes power dissipation under a prescribeduid volume fraction constraint.An arti􀀀cial friction force is added to the Navier-Stokes equations to apply the no-slip boundary condition.Although a great deal of work has been carried out for topology optimization ofuidow in recent years,there are few researches on the topology optimization ofuidow with physical body forces.To simulate theuidow in reality,the constant body force(e.g.,gravity)is considered in this paper.Several 2D numerical examples are presented to discuss the relationships between the proposed method with Reynolds number and initial design,and demonstrate the feasibility and superiority of the proposed method in dealing with unstructuredmesh problems.Three 3D numerical examples demonstrate the proposedmethod is feasible in three-dimensional.

Method of variation of parameters for solving a constrained Birkhoffian system

For an in-depth study on the integration problem of the constrained mechanical systems the method of integration for the Birkhoffian system with constraints is discussed and the method of variation of parameters for solving the dynamical equations of the constrained Birkhoffian system is provided.First the differential equations of motion for the constrained Birkhoffian system as well as for the corresponding free Birkhoffian system are established.Secondly a system of auxiliary equations is constructed and the general solution of the equations is found.Finally by varying the parameters and utilizing the properties of the generalized canonical transformation of the Birkhoffian system the solution of the problem can be obtained.The proposed method reveals the inherent relationship between the solution of a free Birkhoffian system and that of a constrained Birkhoffian system. The research results are of universal significance which can be further used in a variety of constrained mechanical systems such as non-conservative systems and nonholonomic systems etc.

Calculation and experimental study on heating temperature field of super-high strength aluminum alloy thick plate

Stepped heating treatment has been applied to aluminum alloy thick plate to improve the mechanical performance and corrosion resistance.Accurate temperature control of the plate is the difficulty in engineering application.The heating process,the calculation of surface heat transfer coefficient and the accurate temperature control method were studied based on measured heating temperature for the large-size thick plate.The results show that,the temperature difference between the surface and center of the thick plate is small.Based on the temperature uniformity,the surface heat transfer coefficient was calculated,and it is constant below300°C,but grows greatly over300°C.Consequently,a lumped parameter method(LPM)was developed to predict the plate temperature.A stepped solution treatment was designed by using LPM,and verified by finite element method(FEM)and experiments.Temperature curves calculated by LPM and FEM agree well with the experimental data,and the LPM is more convenient in engineering application.

Discussion of Muskingum method parameter X

The parameter X of the Muskingum method is a physical parameter that reflects the flood peak attenuation and hydrograph shape flattening of a diffusion wave in motion. In this paper, the historic process that hydrologists have undergone to find a physical explanation of this parameter is briefly discussed. Based on the fact that the Muskingum method is the second-order accuracy difference solution to the diffusion wave equation, its numerical stability condition is analyzed, and a conclusion is drawn： X ≤ 0.5 is the uniform condition satisfying the demands for its physical meaning and numerical stability. It is also pointed out that the methods that regard the sum of squares of differences between the calculated and observed discharges or stages as the objective function and the routing coefficients C0, C1 and C2 of the Muskingum method as the optimization parameters cannot guarantee the physical meaning of X.

A LOWER BOUND LIMIT ANALYSIS OF DUCTILE COMPOSITE MATERIALS

The plastic load-bearing capacity of ductile composites such as metal matrix composites is studied with an insight into the microstructures. The macroscopic strength of a composite is obtained by combining the homogenization theory with static limit analysis, where the temperature parameter method is used to construct the self-equilibrium stress field. An interface failure model is proposed to account for the effects of the interface on the failure of composites. The static limit analysis with the finite-element method is then formulated as a constrained nonlinear programming problem, which is solved by the Sequential Quadratic Programming （SQP） method. Finally, the macroscopic transverse strength of perforated materials, the macroscopic transverse and off-axis strength of fiber-reinforced composites are obtained through numerical calculation. The computational results are in good agreement with the experimental data.

IMPROVE EFFICIENCY OF BIOGAS FEEDBACK SUPPLY CHAIN IN RURAL CHINA

Feedback supply chain is a key structure in the supply chain system, and the development of feedback supply chain for biogas biomass energy is one of the important ways of the rural ecological civilization construction. Presently, the efficiency problem of biogas supply chain in rural China has been restricting the development of biogas biomass energy business. This article, on the basis of combination of regulation parameters, describes the dynamic changes in the system, using differential equations integrated with simulation to reveal the rules of regulation parameters to investigate the efficiency problem in the biogas supply chain. First of all, on the basis of the actual situation, the flow level and flow rate system structure model and simulation equation set are established for the biogas energy feedback supply chain from a scale livestock farm to peasant households; On the basis of the differentiability of the simulation equation a third order inhomogeneous differential equation with constant coefficients containing regulative parameters is established for the quantity of biogas stored in the feedback supply chain. A theorem and its corollaries are established for the operating efficiency of supply chain to reveal the change law of the quantity of biogas, the quantity of biogas consumed daily by peasant households and its standard-reaching rate as well as other variables.

Ground-state energy of beryllium atom with parameter perturbation method

We present a perturbation study of the ground-state energy of the beryllium atom by incorporating double parameters in the atom＇s Hamiltonian. The eigenvalue of the Hamiltonian is then solved with a double-fold perturbation scheme,where the spin-spin interaction of electrons from different shells of the atom is also considered. Calculations show that the obtained ground-state energy is in satisfactory agreement with experiment. It is found that the Coulomb repulsion of the inner-shell electrons enhances the effective nuclear charge seen by the outer-shell electrons, and the shielding effect of the outer-shell electrons to the nucleus is also notable compared with that of the inner-shell electrons.

Parameter Tuning Method for Dither Compensation of a Pneumatic Proportional Valve with Friction

In the practical application of pneumatic control devices, the nonlinearity of a pneumatic control valve become the main factor affecting the control effect, which comes mainly from the dynamic friction force. The dynamic friction inside the valve may cause hysteresis and a dead zone. In this paper, a dither compensation mechanism is proposed to reduce negative effects on the basis of analyzing the mechanism of friction force. The specific dither signal（using a sinusoidal signal） was superimposed on the control signal of the valve. Based on the relationship between the parameters of the dither signal and the inherent characteristics of the proportional servo valve, a parameter tuning method was proposed, which uses a displacement sensor to measure the maximum static friction inside the valve. According to the experimental results, the proper amplitude ranges are determined for different pressures. In order to get the optimal parameters of the dither signal, some dither compensation experiments have been carried out on different signal amplitude and gas pressure conditions. Optimal parameters are determined under two kinds of pressure conditions. Using tuning parameters the valve spool displacement experiment has been taken. From the experiment results, hysteresis of the proportional servo valve is significantly reduced. And through simulation and experiments, the cut-off frequency of the proportional valve has also been widened. Therefore after adding the dither signal, the static and dynamic characteristics of the proportional valve are both improved to a certain degree. This research proposes a parameter tuning method of dither signal, and the validity of the method is verified experimentally.

SQUEEZE FLOW OF A SECOND-ORDER FLUID BETWEEN TWO PARALLEL DISKS OR TWO SPHERES

The normal viscous force of squeeze flow between two arbitrary rigid spheres with an interstitial second-order fluid was studied for modeling wet granular materials using the discrete element method. Based on the Reynolds' lubrication theory, the small parameter method was introduced to approximately analyze velocity field and stress distribution between the two disks. Then a similar procedure was carried out for analyzing the normal interaction between two nearly touching, arbitrary rigid spheres to obtain the pressure distribution and the resulting squeeze force. It has been proved that the solutions can be reduced to the case of a Newtonian fluid when the non-Newtonian terms are neglected.

Interval finite difference method for steady-state temperature field prediction with interval parameters

A new numerical technique named interval finite difference method is proposed for the steady-state temperature field prediction with uncertainties in both physical parameters and boundary conditions. Interval variables are used to quantitatively describe the uncertain parameters with limited information. Based on different Taylor and Neumann series, two kinds of parameter perturbation methods are presented to approximately yield the ranges of the uncertain temperature field. By comparing the results with traditional Monte Carlo simulation, a numerical example is given to demonstrate the feasibility and effectiveness of the proposed method for solving steady-state heat conduction problem with uncertain-but-bounded parameters.

Singularity of Some Software Reliability Models and Parameter Estimation Method

According to the principle, “The failure data is the basis of software reliability analysis”, we built a software reliability expert system (SRES) by adopting the artificial intelligence technology. By reasoning out the conclusion from the fitting results of failure data of a software project, the SRES can recommend users “the most suitable model” as a software reliability measurement model. We believe that the SRES can overcome the inconsistency in applications of software reliability models well. We report investigation results of singularity and parameter estimation methods of experimental models in SRES.

Gas emission source term estimation with 1-step nonlinear partial swarm optimization-Tikhonov regularization hybrid method

Source term identification is very important for the contaminant gas emission event. Thus, it is necessary to study the source parameter estimation method with high computation efficiency, high estimation accuracy and reasonable confidence interval. Tikhonov regularization method is a potential good tool to identify the source parameters. However, it is invalid for nonlinear inverse problem like gas emission process. 2-step nonlinear and linear PSO （partial swarm optimization）-Tikhonov regularization method proposed previously have estimated the emission source parameters successfully. But there are still some problems in computation efficiency and confidence interval. Hence, a new 1-step nonlinear method combined Tikhonov regularizafion and PSO algorithm with nonlinear forward dispersion model was proposed. First, the method was tested with simulation and experiment cases. The test results showed that 1-step nonlinear hybrid method is able to estimate multiple source parameters with reasonable confidence interval. Then, the estimation performances of different methods were compared with different cases. The estimation values with 1-step nonlinear method were close to that with 2-step nonlinear and linear PSO-Tikhonov regularization method, 1-step nonlinear method even performs better than other two methods in some cases, especially for source strength and downwind distance estimation. Compared with 2-step nonlinear method, 1-step method has higher computation efficiency. On the other hand, the confidence intervals with the method proposed in this paper seem more reasonable than that with other two methods. Finally, single PSO algorithm was compared with 1-step nonlinear PSO-Tikhonov hybrid regularization method. The results showed that the skill scores of 1-step nonlinear hybrid method to estimate source parameters were close to that of single PSO method and even better in some cases. One more important property of 1-step nonlinear PSO-Tikhonov regularization method is its reasonable confidence interval, which is not obtained by single PSO algorithm. Therefore, 1-step nonlinear hybrid regularization method proposed in this paper is a potential good method to estimate contaminant gas emission source term.

Physical Parameter Identification Method Based on Modal Analysis for Two-axis On-road Vehicles:Theory and Simulation

Physical parameters are very important for vehicle dynamic modeling and analysis.However,most of physical parameter identification methods are assuming some physical parameters of vehicle are known,and the other unknown parameters can be identified.In order to identify physical parameters of vehicle in the case that all physical parameters are unknown,a methodology based on the State Variable Method（SVM） for physical parameter identification of two-axis on-road vehicle is presented.The modal parameters of the vehicle are identified by the SVM,furthermore,the physical parameters of the vehicle are estimated by least squares method.In numerical simulations,physical parameters of Ford Granada are chosen as parameters of vehicle model,and half-sine bump function is chosen to simulate tire stimulated by impulse excitation.The first numerical simulation shows that the present method can identify all of the physical parameters and the largest absolute value of percentage error of the identified physical parameter is 0.205%;and the effect of the errors of additional mass,structural parameter and measurement noise are discussed in the following simulations,the results shows that when signal contains 30 d B noise,the largest absolute value of percentage error of the identification is 3.78%.These simulations verify that the presented method is effective and accurate for physical parameter identification of two-axis on-road vehicles.The proposed methodology can identify all physical parameters of 7-DOF vehicle model by using free-decay responses of vehicle without need to assume some physical parameters are known.

Energy Spectrum for a Short-Range 1/r Singular Potential with a Non-Orbital Barrier Using the Asymptotic Iteration Method

Using the asymptotic iteration method, we obtain the S-wave solution for a short-range three-parameter central potential with 1/r singularity and with a non-orbital barrier. To the best of our knowledge, this is the first attempt at calculating the energy spectrum for this potential, which was introduced by H. Bahlouli and A. D. Alhaidari and for which they obtained the “potential parameter spectrum”. Our results are also independently verified using a direct method of diagonalizing the Hamiltonian matrix in the J-matrix basis.

Modelling of Wage and Income Distributions Using the Method of L-Moments

Commonly used statistical procedure to describe the observed statistical sets is to use their conventional moments or cumulants. When choosing an appropriate parametric distribution for the data set is typically that parameters of a parametric distribution are estimated using the moment method of creating a system of equations in which the sample conventional moments lay in the equality of the corresponding moments of the theoretical distribution. However, the moment method of parameter estimation is not always convenient, especially for small samples. An alternative approach is based on the use of other characteristics, which the author calls L-moments. L-moments are analogous to conventional moments, but they are based on linear combinations of order statistics, i.e., L-statistics. Using L-moments is theoretically preferable to the conventional moments and consists in the fact that L-moments characterize a wider range of distribution. When estimating from sample L-moments, L-moments are more robust to the presence of outliers in the data. Experience also shows that, compared to conventional moments, L-moments are less prone to bias of estimation. Parameter estimates obtained using L-moments are mainly in the case of small samples often even more accurate than estimates of parameters made by maximum likelihood method. Using the method of L-moments in the case of small data sets from the meteorology is primarily known in statistical literature. This paper deals with the use of L-moments in the case for large data sets of income distribution （individual data） and wage distribution （data are ordered to form of interval frequency distribution of extreme open intervals）. This paper also presents a comparison of the accuracy of the method of L-moments with an accuracy of other methods of point estimation of parameters of parametric probability distribution in the case of large data sets of individual data and data ordered to form of interval frequency distribution.

Variation Characteristics of Ultraviolet Radiation over the North China Plain

In situ measured data of broadband solar radiation （Rs） and ultraviolet （Uv） radiation were used to investigate the spa- tiotemporal variation properties of Uv radiation and the ratio of Uv radiation to Rs over the North China Plain （NCP）. Based on the analysis, an empirical model for estimating Uv radiation under all weather conditions in this region was developed. The results showed that the annual Uv radiation over the NCP ranges from 0.38-0.52 MJ m^-2 d^-1. The highest value during the study period was recorded at the Changwu site, which is located near the margin of the Loess Plateau, while the lowest value appeared at the station in Beijing. The seasonal variation pattern of the ratio of Uv radiation to Rs is similar to that of Uv radiation; namely, the highest value appears in August and then decreases gradually until the lowest value appears in November. A small increasing trend in the Uv radiation levels and the ratio of Uv radiation to Rs was observed over the NCP. The evaluation results showed that the empirical estimation model can be widely used to estimate Uv radiation under all atmospheric conditions. The relative error between the modeled and measured daily values were within ± 15%.