Background:The development of computer vision technology has enabled the use of markerless movement tracking for biomechanical analysis.Recent research has reported the feasibility of markerless systems in motion anal...Background:The development of computer vision technology has enabled the use of markerless movement tracking for biomechanical analysis.Recent research has reported the feasibility of markerless systems in motion analysis but has yet to fully explore their utility for capturing faster movements,such as running.Applied studies using markerless systems in clinical and sports settings are still lacking.Thus,the present study compared running biomechanics estimated by marker-based and markerless systems.Given running speed not only affects sports performance but is also associated with clinical injury prevention,diagnosis,and rehabilitation,we aimed to investigate the effects of speed on the comparison of estimated lower extremity joint moments and powers between markerless and marker-based technologies during treadmill running as a concurrent validating study.Methods:Kinematic data from marker-based/markerless technologies were collected,along with ground reaction force data,from 16 young adults running on an instrumented treadmill at 3 speeds:2.24 m/s,2.91 m/s,and 3.58 m/s(5.0 miles/h,6.5 miles/h,and 8.0 miles/h).Sagittal plane moments and powers of the hip,knee,and ankle were calculated by inverse dynamic methods.Time series analysis and statistical parametric mapping were used to determine system differences.Results:Compared to the marker-based system,the markerless system estimated increased lower extremity joint kinetics with faster speed during the swing phase in most cases.Conclusion:Despite the promising application of markerless technology in clinical settings,systematic markerless overestimation requires focused attention.Based on segment pose estimations,the centers of mass estimated by markerless technologies were farther away from the relevant distal joint centers,which led to greater joint moments and powers estimates by markerless vs.marker-based systems.The differences were amplified by running speed.展开更多
In this study,the instability and bifurcation diagrams of a functionally graded(FG)porous sandwich beam on an elastic,viscous foundation which is influenced by an axial load,are investigated with an analytical attitud...In this study,the instability and bifurcation diagrams of a functionally graded(FG)porous sandwich beam on an elastic,viscous foundation which is influenced by an axial load,are investigated with an analytical attitude.To do so,the Timoshenko beam theory is utilized to take the shear deformations into account,and the nonlinear Von-Karman approach is adopted to acquire the equations of motion.Then,to turn the partial differential equations(PDEs)into ordinary differential equations(ODEs)in the case of equations of motion,the method of Galerkin is employed,followed by the multiple time scale method to solve the resulting equations.The impact of parameters affecting the response of the beam,including the porosity distribution,porosity coefficient,temperature increments,slenderness,thickness,and damping ratios,are explicitly discussed.It is found that the parameters mentioned above affect the bifurcation points and instability of the sandwich porous beams,some of which,including the effect of temperature and porosity distribution,are less noticeable.展开更多
We study the nonlinear stage of modulation instability(MI)in the non-intergrable pure-quartic nonlinear Schrödinger equation where the fourth-order dispersion is modulated periodically.Using the three-mode trunca...We study the nonlinear stage of modulation instability(MI)in the non-intergrable pure-quartic nonlinear Schrödinger equation where the fourth-order dispersion is modulated periodically.Using the three-mode truncation,we reveal the complex recurrence of parametric resonance(PR)breathers,where each recurrence is associated with two oscillation periods(PR period and internal oscillation period).The nonlinear stage of parametric instability admits the maximum energy exchange between the spectrum sidebands and central mode occurring outside the MI gain band.展开更多
Based on the generalized Hamilton's principle,the nonlinear governing equation of an axially functionally graded(AFG)pipe is established.The non-trivial equilibrium configuration is superposed by the modal functio...Based on the generalized Hamilton's principle,the nonlinear governing equation of an axially functionally graded(AFG)pipe is established.The non-trivial equilibrium configuration is superposed by the modal functions of a simply supported beam.Via the direct multi-scale method,the response and stability boundary to the pulsating fluid velocity are solved analytically and verified by the differential quadrature element method(DQEM).The influence of Young's modulus gradient on the parametric resonance is investigated in the subcritical and supercritical regions.In general,the pipe in the supercritical region is more sensitive to the pulsating excitation.The nonlinearity changes from hard to soft,and the non-trivial equilibrium configuration introduces more frequency components to the vibration.Besides,the increasing Young's modulus gradient improves the critical pulsating flow velocity of the parametric resonance,and further enhances the stability of the system.In addition,when the temperature increases along the axial direction,reducing the gradient parameter can enhance the response asymmetry.This work further complements the theoretical analysis of pipes conveying pulsating fluid.展开更多
High-power O-mode radio waves can excite artificial instabilities in the F region,according to experiments conducted at the European Incoherent Scatter Science Association(EISCAT)heating facility.The main instabilitie...High-power O-mode radio waves can excite artificial instabilities in the F region,according to experiments conducted at the European Incoherent Scatter Science Association(EISCAT)heating facility.The main instabilities include the parametric decay instability(PDI),oscillating two-stream instability(OTSI),and thermal parametric instability(TPI).The PDI and OTSI not only compete with each other,but also compete with the TPI,leading to a two-stage overshoot phenomenon:a miniovershoot occurs on a millisecond time scale after pump-on,followed by the main overshoot.We gain insight into the miniovershoot via a generalized Zakharov model,whereas the main overshoot can be observed as an enhanced plasma line overshoot phenomenon in incoherent scatter radar spectra.We can also observe that the zero-frequency ion line exists only in the initial heating period after a cold start and that the upshifted and downshifted ion lines behave irregularly in the spectra.The simulation results show that competition between the PDI and OTSI leads to an initial peak,which we named the pre-miniovershoot.The following processes,namely ion density caviton generation,and collapse and cascade in the development of the PDI,contribute to the miniovershoot phenomenon.展开更多
Due to the novel applications of flexible pipes conveying fluid in the field of soft robotics and biomedicine,the investigations on the mechanical responses of the pipes have attracted considerable attention.The fluid...Due to the novel applications of flexible pipes conveying fluid in the field of soft robotics and biomedicine,the investigations on the mechanical responses of the pipes have attracted considerable attention.The fluid-structure interaction(FSI)between the pipe with a curved shape and the time-varying internal fluid flow brings a great challenge to the revelation of the dynamical behaviors of flexible pipes,especially when the pipe is highly flexible and usually undergoes large deformations.In this work,the geometrically exact model(GEM)for a curved cantilevered pipe conveying pulsating fluid is developed based on the extended Hamilton's principle.The stability of the curved pipe with three different subtended angles is examined with the consideration of steady fluid flow.Specific attention is concentrated on the large-deformation resonance of circular pipes conveying pulsating fluid,which is often encountered in practical engineering.By constructing bifurcation diagrams,oscillating shapes,phase portraits,time traces,and Poincarémaps,the dynamic responses of the curved pipe under various system parameters are revealed.The mean flow velocity of the pulsating fluid is chosen to be either subcritical or supercritical.The numerical results show that the curved pipe conveying pulsating fluid can exhibit rich dynamical behaviors,including periodic and quasi-periodic motions.It is also found that the preferred instability type of a cantilevered curved pipe conveying steady fluid is mainly in the flutter of the second mode.For a moderate value of the mass ratio,however,a third-mode flutter may occur,which is quite different from that of a straight pipe system.展开更多
A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A ...A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A typical JTWPA consists of thousands of Josephson junctions connected in series to form a transmission line and hundreds of shunt LC resonators periodically loaded along the line for phase matching.Because the variation of these capacitors and inductors can be detrimental to their high-frequency characteristics,the fabrication of a JTWPA typically necessitates precise processing equipment.To guide the fabrication process and further improve the design for manufacturability,it is necessary to understand how each electronic component affects the amplifier.In this paper,we use the harmonic balance method to conduct a comprehensive study on the impact of nonuniformity and fabrication yield of the electronic components on the performance of a JTWPA.The results provide insightful and scientific guidance for device design and fabrication processes.展开更多
Fishing boats have unique features that make them prone to changing loading conditions.When the boat leaves the port,the empty fish tank gradually fills up during fishing operations which may result in parametric roll...Fishing boats have unique features that make them prone to changing loading conditions.When the boat leaves the port,the empty fish tank gradually fills up during fishing operations which may result in parametric roll(PR).This dangerous phenomenon that can lead to capsizing.The present study aims to understand better the behaviour of parametric roll in fishing boats and its relation to changing loading conditions.The study considers the effects of displacement and the GM/KM ratio on parametric roll,as well as the longitudinal flare distribution at the waterline.Two assessments to detect the parametric roll occurrence in early stage were carried out by using the level 1 assessment of parametric roll based on the Second Generation of Intact Stability criteria(SGIS)from International maritime Organisation(IMO)and the Susceptibility criteria of Parametric roll from the American Bureau of Shipping(ABS).Then,the CFD method is used to predict the amplitude of the parametric roll phenomenon.The results provide important insights to fishing vessel operators on how to manage loading conditions to maintain stability and avoid hazardous situations.By following the guidelines outlined in this study,fishing boats can operate more safely and efficiently,reducing the risk of accidents and improving the overall sustainability of the fishing industry.展开更多
The widespread adoption of aluminumalloy electric buses,known for their energy efficiency and eco-friendliness,faces a challenge due to the aluminum frame’s susceptibility to deformation compared to steel.This issue ...The widespread adoption of aluminumalloy electric buses,known for their energy efficiency and eco-friendliness,faces a challenge due to the aluminum frame’s susceptibility to deformation compared to steel.This issue is further exacerbated by the stringent requirements imposed by the flammability and explosiveness of batteries,necessitating robust frame protection.Our study aims to optimize the connectors of aluminum alloy bus frames,emphasizing durability,energy efficiency,and safety.This research delves into Multi-Objective Coordinated Optimization(MCO)techniques for lightweight design in aluminum alloy bus body connectors.Our goal is to enhance lightweighting,reinforce energy absorption,and improve deformation resistance in connector components.Three typical aluminum alloy connectors were selected and a design optimization platform was built for their MCO using a variety of software and methods.Firstly,through three-point bending experiments and finite element analysis on three types of connector components,we identified optimized design parameters based on deformation patterns.Then,employing Optimal Latin hypercube design(OLHD),parametric modeling,and neural network approximation,we developed high-precision approximate models for the design parameters of each connector component,targeting energy absorption,mass,and logarithmic strain.Lastly,utilizing the Archive-based Micro Genetic Algorithm(AMGA),Multi-Objective Particle Swarm Optimization(MOPSO),and Non-dominated SortingGenetic Algorithm(NSGA2),we explored optimized design solutions for these joint components.Subsequently,we simulated joint assembly buckling during bus rollover crash scenarios to verify and analyze the optimized solutions in three-point bending simulations.Each joint component showcased a remarkable 30%–40%mass reduction while boosting energy absorption.Our design optimization method exhibits high efficiency and costeffectiveness.Leveraging contemporary automation technology,the design optimization platform developed in this study is poised to facilitate intelligent optimization of lightweight metal components in future applications.展开更多
The surrounding geological conditions and supporting structures of underground engineering are often updated during construction,and these updates require repeated numerical modeling.To improve the numerical modeling ...The surrounding geological conditions and supporting structures of underground engineering are often updated during construction,and these updates require repeated numerical modeling.To improve the numerical modeling efficiency of underground engineering,a modularized and parametric modeling cloud server is developed by using Python codes.The basic framework of the cloud server is as follows:input the modeling parameters into the web platform,implement Rhino software and FLAC3D software to model and run simulations in the cloud server,and return the simulation results to the web platform.The modeling program can automatically generate instructions that can run the modeling process in Rhino based on the input modeling parameters.The main modules of the modeling program include modeling the 3D geological structures,the underground engineering structures,and the supporting structures as well as meshing the geometric models.In particular,various cross-sections of underground caverns are crafted as parametricmodules in themodeling program.Themodularized and parametric modeling program is used for a finite element simulation of the underground powerhouse of the Shuangjiangkou Hydropower Station.This complicatedmodel is rapidly generated for the simulation,and the simulation results are reasonable.Thus,this modularized and parametric modeling program is applicable for three-dimensional finite element simulations and analyses.展开更多
Modeling dynamic systems with linear parametric models usually suffer limitation which affects forecasting performance and policy implications. This paper advances a non-parametric autoregressive distributed lag model...Modeling dynamic systems with linear parametric models usually suffer limitation which affects forecasting performance and policy implications. This paper advances a non-parametric autoregressive distributed lag model that employs a Bayesian additive regression tree (BART). The performance of the BART model is compared with selection models like Lasso, Elastic Net, and Bayesian networks in simulation experiments with linear and non-linear data generating processes (DGP), and on US macroeconomic time series data. The results show that the BART model is quite competitive against the linear parametric methods when the DGP is linear, and outperforms the competing methods when the DGP is non-linear. The empirical results suggest that the BART estimators are generally more efficient than the traditional linear methods when modeling and forecasting macroeconomic time series.展开更多
The study investigates long-term changes in annual and seasonal rainfall patterns in the Indira Sagar Region of Madhya Pradesh, India, from 1901 to 2010. Agriculture sustainability, food supply, natural resource devel...The study investigates long-term changes in annual and seasonal rainfall patterns in the Indira Sagar Region of Madhya Pradesh, India, from 1901 to 2010. Agriculture sustainability, food supply, natural resource development, and hydropower system reliability in the region rely heavily on monsoon rainfall. Monthly rainfall data from three stations (East Nimar, Barwani, and West Nimar) were analyzed. Initially, the pre-whitening method was applied to eliminate serial correlation effects from the rainfall data series. Subsequently, statistical trends in annual and seasonal rainfall were assessed using both parametric (student-t test) and non-parametric tests [Mann-Kendall, Sen’s slope estimator, and Cumulative Sum (CUSUM)]. The magnitude of the rainfall trend was determined using Theil-Sen’s slope estimator. Spatial analysis of the Mann-Kendall test on an annual basis revealed a statistically insignificant decreasing trend for Barwani and East Nimar and an increasing trend for West Nimar. On a seasonal basis, the monsoon season contributes a significant percentage (88.33%) to the total annual rainfall. The CUSUM test results indicated a shift change detection in annual rainfall data for Barwani in 1997, while shifts were observed in West and East Nimar stations in 1929. These findings offer valuable insights into regional rainfall behavior, aiding in the planning and management of water resources and ecological systems.展开更多
With the advancement of technology and the development of cities,urban planning and management methods are also constantly improving.From paper-based assignments to modern digitization,new technologies have enabled mo...With the advancement of technology and the development of cities,urban planning and management methods are also constantly improving.From paper-based assignments to modern digitization,new technologies have enabled more efficient design and management for cities.3D modeling can used to simulate the urban environment,which can assist in urban planning and management.However,large-scale modeling cannot be achieved through existing modeling methods,and there are still some shortcomings in the maintenance of the model.Therefore,this article proposes a Computer Generated Architecture(CGA)parametric 3D modeling method based on CityEngine.Research on expanding and customizing modeling rules to create indoor and outdoor modeling rule templates for buildings and methods for generating urban 3D models have been carried out.The results have shown that the completed model can be displayed on different platforms thanks to parameterized modeling.The model can be modified easily and directly applied to the analysis and decision-making of urban planning schemes.展开更多
The generation of power-and wavelength-scalable few optical cycle pulses remains one of the major challenges in modern laser physics.Over the past decade,the development of table-top optical parametric chirped pulse a...The generation of power-and wavelength-scalable few optical cycle pulses remains one of the major challenges in modern laser physics.Over the past decade,the development of table-top optical parametric chirped pulse amplificationbased systems was progressing at amazing speed,demonstrating excellent performance characteristics in terms of pulse duration,energy,peak power and repetition rate,which place them at the front line of modern ultrafast laser technology.At present,table-top optical parametric chirped pulse amplifiers comprise a unique class of ultrafast light sources,which currently amplify octave-spanning spectra and produce carrier-envelope phase-stable,few optical cycle pulses with multi-gigawatt to multi-terawatt peak powers and multi-watt average powers,with carrier wavelengths spanning a considerable range of the optical spectrum.This article gives an overview on the state of the art of table-top optical parametric chirped pulse amplifiers,addressing their relevant scientific and technological aspects,and provides a short outlook of practical applications in the growing field of ultrafast science.展开更多
Nonlinear optical imaging is a versatile tool that has been proven to be exceptionally useful in various research fields.However,due to the use of photomultiplier tubes(PMTs),the wide application of nonlinear optical ...Nonlinear optical imaging is a versatile tool that has been proven to be exceptionally useful in various research fields.However,due to the use of photomultiplier tubes(PMTs),the wide application of nonlinear optical imaging is limited by the incapability of imaging under am-bient light.In this paper,we propose and demonstrate a new optical imaging detection method based on optical parametric amplification(OPA).As a nonlinear optical process,OPA in-trinsically rejects ambient light photons by coherence gating.Periodical poled lithium niobate(PPLN)crystals are used in this study as the media for OPA.Compared to bulk nonlinear optical crystals,PPLN crystals support the generation of OPA signal with lower pump power.Therefore,this characteristic of PPLN crystals is particularly beneficial when using high-repetition-rate lasers,which facilitate high-speed optical signal detection,such as in spec-troscopy and imaging.A PPLN-based OPA system was built to amplify the emitted imaging signal from second harmonic generation(SHG)and coherent anti-Stokes Raman scattering(CARS)microscopy imaging,and the amplified optical signal was strong enough to be detected by a biased photodiode under ordinary room light conditions.With OPA detection,ambient-light-on SHG and CARS imaging becomes possible,and achieves a similar result as PMT detection under strictly dark environments.These results demonstrate that OPA can be used as a substitute for PMTs in nonlinear optical imaging to adapt it to various applications with complex.light ing conditions.展开更多
Taking bump-type gas foil bearings as the research object,a deformation model of bump foil and a thin-plate finite element model of top foil were proposed.By solving Reynolds equation and energy equation,the pressure ...Taking bump-type gas foil bearings as the research object,a deformation model of bump foil and a thin-plate finite element model of top foil were proposed.By solving Reynolds equation and energy equation,the pressure distribution and the temperature distribution of gas films in foil bearings were obtained.Further,a numerical method for calculating the lubrication performance of gas foil bearings with considering the surface roughness was proposed.With a specific example,effects of the surface roughness on the bearing lubrication performance were parametrically studied.The results indicate that rougher journal surface can lead to larger fluctuation of the lubrication performance,while surface roughness of top foil has few effects on the fluctuation.Moreover,the mean values of performance parameters almost remain constant at different values of surface roughness.展开更多
This paper introduces an aircraft wing simulation data set(AWSD)created by an automatic workflow based on creating models,meshing.simulating the wing flight flow field solution,and parameterizing solution results.AWSD...This paper introduces an aircraft wing simulation data set(AWSD)created by an automatic workflow based on creating models,meshing.simulating the wing flight flow field solution,and parameterizing solution results.AWSD is a flexible,independent wing collection of simulations with specific engineering requirements.The data set is applicable to handle computer geometry processing tasks.In contrast to the existing 3D model data set,there are some advantages the scale of this data set is not limited by the collection source,the data files have high quality,no defects,redundancy,and other problems,and the models and simulation are all designed for the specific actual engineering demand.Moreover,AWSD has the characteristics of rich information and a similar model structure,which contributes to the construction of the surrogate model.On the other hand,this data set is suitable for advancing research of data mining in computational geometry graphics.To solve the problem that the CFD flows field results are not intuitive,this paper used the resampling method of surface data to sample the result to the model surface,then segmented the re sampled 3D mesh surface,and compared with the diferences among K-means algorithm,Mini_Batch K means algorithm,and Spectral Clustering algorithm.AWSD provides 300 sets of models,meshes,CFD simulation results,and parametric results based on ARAP(As-Rigid-As Posible)and Harmonic mapping for advancing the construction of engineering surrogate models,3D mesh segmentation,surface resampling,and related geometric processing tasks.展开更多
Spin pumping(SP)and inverse spin Hall effect(ISHE)driven by parametrically-excited dipole-exchange spin waves in a yttrium iron garnet film have been systematically investigated.The measured voltage spectrum exhibits ...Spin pumping(SP)and inverse spin Hall effect(ISHE)driven by parametrically-excited dipole-exchange spin waves in a yttrium iron garnet film have been systematically investigated.The measured voltage spectrum exhibits a feature of the field-induced transition from parallel pumping to perpendicular pumping because of the inhomogeneous excitation geometry.Thanks to the high precision of the SP-ISHE detection,two sets of fine structures in the voltage spectrum are observed,which can correspond well to two kinds of critical points in the multimode spin-wave spectrum for magnetic films.One is the q=0 point of each higher-order dispersion branch,and the other is the local minimum due to the interplay between the dipolar and exchange interactions.These fine structures on the voltage spectrum confirm the spin pumping by higher-order dipole-exchange spin-wave modes,and are helpful for probing the multimode spin-wave spectrum.展开更多
The nuclear fuel assembly is the core component of a nuclear reactor.In a pressurized water reactor fuel assembly,the top-connection structure connects the top nozzle to the guide thimble.Its performance reliability i...The nuclear fuel assembly is the core component of a nuclear reactor.In a pressurized water reactor fuel assembly,the top-connection structure connects the top nozzle to the guide thimble.Its performance reliability is essential for the stability of the nuclear fuel assembly.In this study,an assembly-oriented reliability analysis method for top-connection structures is presented by establishing an assembly-oriented top-connection structure parameter modeling method and a nonlinear contact gap and penetration correction method.A reliability model of the top-connection assembly structure,including multiple stochastic design variables,was constructed,and the overall reliability of the top-connection assembly structure was obtained via a Kriging model and Monte Carlo simulation.The acquired experimental data were consistent with real-world failure conditions,which verified the practicability and feasibility of the reliability analysis method proposed in this study.展开更多
Reinforced concrete(RC)structures are common in engineering,and usually exposed to air or water,may be subjected to various blast scenarios.This paper aims to investigate the blast resistance of an airbacked RC slab a...Reinforced concrete(RC)structures are common in engineering,and usually exposed to air or water,may be subjected to various blast scenarios.This paper aims to investigate the blast resistance of an airbacked RC slab against underwater contact explosions(UWCEs).A detailed numerical model based on CLE method considering explosive,water,air,and RC slab is developed to examine the structural behavior of the air-backed RC slab due to UWCEs.At first,the reliability of the numerical method is validated by comparing the numerical results of an UWCE test with experimental data.Then,the difference in dynamic behavior of air-backed and water-backed RC slabs due to UWCEs is explored with the calibrated model.The results indicate that the blast response of the air-backed slab induced by UWCE is fiercer than that of water-backed slab with equal charge mass.In addition,parametric studies are also conducted to explore the effects of the charge mass,standoff distance,reinforcement spacing,concrete compression strength,and boundary condition on the blast performance of the air-backed RC slab.展开更多
文摘Background:The development of computer vision technology has enabled the use of markerless movement tracking for biomechanical analysis.Recent research has reported the feasibility of markerless systems in motion analysis but has yet to fully explore their utility for capturing faster movements,such as running.Applied studies using markerless systems in clinical and sports settings are still lacking.Thus,the present study compared running biomechanics estimated by marker-based and markerless systems.Given running speed not only affects sports performance but is also associated with clinical injury prevention,diagnosis,and rehabilitation,we aimed to investigate the effects of speed on the comparison of estimated lower extremity joint moments and powers between markerless and marker-based technologies during treadmill running as a concurrent validating study.Methods:Kinematic data from marker-based/markerless technologies were collected,along with ground reaction force data,from 16 young adults running on an instrumented treadmill at 3 speeds:2.24 m/s,2.91 m/s,and 3.58 m/s(5.0 miles/h,6.5 miles/h,and 8.0 miles/h).Sagittal plane moments and powers of the hip,knee,and ankle were calculated by inverse dynamic methods.Time series analysis and statistical parametric mapping were used to determine system differences.Results:Compared to the marker-based system,the markerless system estimated increased lower extremity joint kinetics with faster speed during the swing phase in most cases.Conclusion:Despite the promising application of markerless technology in clinical settings,systematic markerless overestimation requires focused attention.Based on segment pose estimations,the centers of mass estimated by markerless technologies were farther away from the relevant distal joint centers,which led to greater joint moments and powers estimates by markerless vs.marker-based systems.The differences were amplified by running speed.
文摘In this study,the instability and bifurcation diagrams of a functionally graded(FG)porous sandwich beam on an elastic,viscous foundation which is influenced by an axial load,are investigated with an analytical attitude.To do so,the Timoshenko beam theory is utilized to take the shear deformations into account,and the nonlinear Von-Karman approach is adopted to acquire the equations of motion.Then,to turn the partial differential equations(PDEs)into ordinary differential equations(ODEs)in the case of equations of motion,the method of Galerkin is employed,followed by the multiple time scale method to solve the resulting equations.The impact of parameters affecting the response of the beam,including the porosity distribution,porosity coefficient,temperature increments,slenderness,thickness,and damping ratios,are explicitly discussed.It is found that the parameters mentioned above affect the bifurcation points and instability of the sandwich porous beams,some of which,including the effect of temperature and porosity distribution,are less noticeable.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.12175178 and 12247103)the Natural Science Basic Research Program of Shaanxi Province,China(Grant No.2022KJXX-71)the Shaanxi Fundamental Science Research Project for Mathematics and Physics(Grant No.22JSY016).
文摘We study the nonlinear stage of modulation instability(MI)in the non-intergrable pure-quartic nonlinear Schrödinger equation where the fourth-order dispersion is modulated periodically.Using the three-mode truncation,we reveal the complex recurrence of parametric resonance(PR)breathers,where each recurrence is associated with two oscillation periods(PR period and internal oscillation period).The nonlinear stage of parametric instability admits the maximum energy exchange between the spectrum sidebands and central mode occurring outside the MI gain band.
基金Project supported by the National Natural Science Foundation of China (Nos.12002195 and 12372015)the National Science Fund for Distinguished Young Scholars of China (No.12025204)the Program of Shanghai Municipal Education Commission of China (No.2019-01-07-00-09-E00018)。
文摘Based on the generalized Hamilton's principle,the nonlinear governing equation of an axially functionally graded(AFG)pipe is established.The non-trivial equilibrium configuration is superposed by the modal functions of a simply supported beam.Via the direct multi-scale method,the response and stability boundary to the pulsating fluid velocity are solved analytically and verified by the differential quadrature element method(DQEM).The influence of Young's modulus gradient on the parametric resonance is investigated in the subcritical and supercritical regions.In general,the pipe in the supercritical region is more sensitive to the pulsating excitation.The nonlinearity changes from hard to soft,and the non-trivial equilibrium configuration introduces more frequency components to the vibration.Besides,the increasing Young's modulus gradient improves the critical pulsating flow velocity of the parametric resonance,and further enhances the stability of the system.In addition,when the temperature increases along the axial direction,reducing the gradient parameter can enhance the response asymmetry.This work further complements the theoretical analysis of pipes conveying pulsating fluid.
基金the National Natural Science Foundation of China(NSFC Grant Nos.42104150,42074187,41774162,and 41704155)the Foundation of the National Key Laboratory of the Electromagnetic Environment(Grant No.6142403200303)+2 种基金the Chinese Academy of Sciences,Key Laboratory of Geospace Environment,University of Science&Technology of China(Grant No.GE2020-01)the Fundamental Research Funds for the Central Universities(Grant No.2042021kf0020)the Excellent Youth Foundation of Hubei Provincial Natural Science Foundation(Grant No.2019CFA054).
文摘High-power O-mode radio waves can excite artificial instabilities in the F region,according to experiments conducted at the European Incoherent Scatter Science Association(EISCAT)heating facility.The main instabilities include the parametric decay instability(PDI),oscillating two-stream instability(OTSI),and thermal parametric instability(TPI).The PDI and OTSI not only compete with each other,but also compete with the TPI,leading to a two-stage overshoot phenomenon:a miniovershoot occurs on a millisecond time scale after pump-on,followed by the main overshoot.We gain insight into the miniovershoot via a generalized Zakharov model,whereas the main overshoot can be observed as an enhanced plasma line overshoot phenomenon in incoherent scatter radar spectra.We can also observe that the zero-frequency ion line exists only in the initial heating period after a cold start and that the upshifted and downshifted ion lines behave irregularly in the spectra.The simulation results show that competition between the PDI and OTSI leads to an initial peak,which we named the pre-miniovershoot.The following processes,namely ion density caviton generation,and collapse and cascade in the development of the PDI,contribute to the miniovershoot phenomenon.
基金Project supported by the National Natural Science Foundation of China (Nos.12072119,12325201,and 52205594)the China National Postdoctoral Program for Innovative Talents (No.BX20220118)。
文摘Due to the novel applications of flexible pipes conveying fluid in the field of soft robotics and biomedicine,the investigations on the mechanical responses of the pipes have attracted considerable attention.The fluid-structure interaction(FSI)between the pipe with a curved shape and the time-varying internal fluid flow brings a great challenge to the revelation of the dynamical behaviors of flexible pipes,especially when the pipe is highly flexible and usually undergoes large deformations.In this work,the geometrically exact model(GEM)for a curved cantilevered pipe conveying pulsating fluid is developed based on the extended Hamilton's principle.The stability of the curved pipe with three different subtended angles is examined with the consideration of steady fluid flow.Specific attention is concentrated on the large-deformation resonance of circular pipes conveying pulsating fluid,which is often encountered in practical engineering.By constructing bifurcation diagrams,oscillating shapes,phase portraits,time traces,and Poincarémaps,the dynamic responses of the curved pipe under various system parameters are revealed.The mean flow velocity of the pulsating fluid is chosen to be either subcritical or supercritical.The numerical results show that the curved pipe conveying pulsating fluid can exhibit rich dynamical behaviors,including periodic and quasi-periodic motions.It is also found that the preferred instability type of a cantilevered curved pipe conveying steady fluid is mainly in the flutter of the second mode.For a moderate value of the mass ratio,however,a third-mode flutter may occur,which is quite different from that of a straight pipe system.
基金support from the Youth Innovation Promotion Association of Chinese Academy of Sciences (Grant No.2019319)support from the Start-up Foundation of Suzhou Institute of Nano-Tech and Nano-Bionics,CAS,Suzhou (Grant No.Y9AAD110)。
文摘A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A typical JTWPA consists of thousands of Josephson junctions connected in series to form a transmission line and hundreds of shunt LC resonators periodically loaded along the line for phase matching.Because the variation of these capacitors and inductors can be detrimental to their high-frequency characteristics,the fabrication of a JTWPA typically necessitates precise processing equipment.To guide the fabrication process and further improve the design for manufacturability,it is necessary to understand how each electronic component affects the amplifier.In this paper,we use the harmonic balance method to conduct a comprehensive study on the impact of nonuniformity and fabrication yield of the electronic components on the performance of a JTWPA.The results provide insightful and scientific guidance for device design and fabrication processes.
文摘Fishing boats have unique features that make them prone to changing loading conditions.When the boat leaves the port,the empty fish tank gradually fills up during fishing operations which may result in parametric roll(PR).This dangerous phenomenon that can lead to capsizing.The present study aims to understand better the behaviour of parametric roll in fishing boats and its relation to changing loading conditions.The study considers the effects of displacement and the GM/KM ratio on parametric roll,as well as the longitudinal flare distribution at the waterline.Two assessments to detect the parametric roll occurrence in early stage were carried out by using the level 1 assessment of parametric roll based on the Second Generation of Intact Stability criteria(SGIS)from International maritime Organisation(IMO)and the Susceptibility criteria of Parametric roll from the American Bureau of Shipping(ABS).Then,the CFD method is used to predict the amplitude of the parametric roll phenomenon.The results provide important insights to fishing vessel operators on how to manage loading conditions to maintain stability and avoid hazardous situations.By following the guidelines outlined in this study,fishing boats can operate more safely and efficiently,reducing the risk of accidents and improving the overall sustainability of the fishing industry.
基金the National Natural Science Foundation of China(Grant Number 52075553)the Postgraduate Research and Innovation Project of Central South University(School-Enterprise Association)(Grant Number 2021XQLH014).
文摘The widespread adoption of aluminumalloy electric buses,known for their energy efficiency and eco-friendliness,faces a challenge due to the aluminum frame’s susceptibility to deformation compared to steel.This issue is further exacerbated by the stringent requirements imposed by the flammability and explosiveness of batteries,necessitating robust frame protection.Our study aims to optimize the connectors of aluminum alloy bus frames,emphasizing durability,energy efficiency,and safety.This research delves into Multi-Objective Coordinated Optimization(MCO)techniques for lightweight design in aluminum alloy bus body connectors.Our goal is to enhance lightweighting,reinforce energy absorption,and improve deformation resistance in connector components.Three typical aluminum alloy connectors were selected and a design optimization platform was built for their MCO using a variety of software and methods.Firstly,through three-point bending experiments and finite element analysis on three types of connector components,we identified optimized design parameters based on deformation patterns.Then,employing Optimal Latin hypercube design(OLHD),parametric modeling,and neural network approximation,we developed high-precision approximate models for the design parameters of each connector component,targeting energy absorption,mass,and logarithmic strain.Lastly,utilizing the Archive-based Micro Genetic Algorithm(AMGA),Multi-Objective Particle Swarm Optimization(MOPSO),and Non-dominated SortingGenetic Algorithm(NSGA2),we explored optimized design solutions for these joint components.Subsequently,we simulated joint assembly buckling during bus rollover crash scenarios to verify and analyze the optimized solutions in three-point bending simulations.Each joint component showcased a remarkable 30%–40%mass reduction while boosting energy absorption.Our design optimization method exhibits high efficiency and costeffectiveness.Leveraging contemporary automation technology,the design optimization platform developed in this study is poised to facilitate intelligent optimization of lightweight metal components in future applications.
基金The Construction S&T Project of the Department of Transportation of Sichuan Province(Grant No.2023A02)the National Natural Science Foundation of China(No.52109135).
文摘The surrounding geological conditions and supporting structures of underground engineering are often updated during construction,and these updates require repeated numerical modeling.To improve the numerical modeling efficiency of underground engineering,a modularized and parametric modeling cloud server is developed by using Python codes.The basic framework of the cloud server is as follows:input the modeling parameters into the web platform,implement Rhino software and FLAC3D software to model and run simulations in the cloud server,and return the simulation results to the web platform.The modeling program can automatically generate instructions that can run the modeling process in Rhino based on the input modeling parameters.The main modules of the modeling program include modeling the 3D geological structures,the underground engineering structures,and the supporting structures as well as meshing the geometric models.In particular,various cross-sections of underground caverns are crafted as parametricmodules in themodeling program.Themodularized and parametric modeling program is used for a finite element simulation of the underground powerhouse of the Shuangjiangkou Hydropower Station.This complicatedmodel is rapidly generated for the simulation,and the simulation results are reasonable.Thus,this modularized and parametric modeling program is applicable for three-dimensional finite element simulations and analyses.
文摘Modeling dynamic systems with linear parametric models usually suffer limitation which affects forecasting performance and policy implications. This paper advances a non-parametric autoregressive distributed lag model that employs a Bayesian additive regression tree (BART). The performance of the BART model is compared with selection models like Lasso, Elastic Net, and Bayesian networks in simulation experiments with linear and non-linear data generating processes (DGP), and on US macroeconomic time series data. The results show that the BART model is quite competitive against the linear parametric methods when the DGP is linear, and outperforms the competing methods when the DGP is non-linear. The empirical results suggest that the BART estimators are generally more efficient than the traditional linear methods when modeling and forecasting macroeconomic time series.
文摘The study investigates long-term changes in annual and seasonal rainfall patterns in the Indira Sagar Region of Madhya Pradesh, India, from 1901 to 2010. Agriculture sustainability, food supply, natural resource development, and hydropower system reliability in the region rely heavily on monsoon rainfall. Monthly rainfall data from three stations (East Nimar, Barwani, and West Nimar) were analyzed. Initially, the pre-whitening method was applied to eliminate serial correlation effects from the rainfall data series. Subsequently, statistical trends in annual and seasonal rainfall were assessed using both parametric (student-t test) and non-parametric tests [Mann-Kendall, Sen’s slope estimator, and Cumulative Sum (CUSUM)]. The magnitude of the rainfall trend was determined using Theil-Sen’s slope estimator. Spatial analysis of the Mann-Kendall test on an annual basis revealed a statistically insignificant decreasing trend for Barwani and East Nimar and an increasing trend for West Nimar. On a seasonal basis, the monsoon season contributes a significant percentage (88.33%) to the total annual rainfall. The CUSUM test results indicated a shift change detection in annual rainfall data for Barwani in 1997, while shifts were observed in West and East Nimar stations in 1929. These findings offer valuable insights into regional rainfall behavior, aiding in the planning and management of water resources and ecological systems.
文摘With the advancement of technology and the development of cities,urban planning and management methods are also constantly improving.From paper-based assignments to modern digitization,new technologies have enabled more efficient design and management for cities.3D modeling can used to simulate the urban environment,which can assist in urban planning and management.However,large-scale modeling cannot be achieved through existing modeling methods,and there are still some shortcomings in the maintenance of the model.Therefore,this article proposes a Computer Generated Architecture(CGA)parametric 3D modeling method based on CityEngine.Research on expanding and customizing modeling rules to create indoor and outdoor modeling rule templates for buildings and methods for generating urban 3D models have been carried out.The results have shown that the completed model can be displayed on different platforms thanks to parameterized modeling.The model can be modified easily and directly applied to the analysis and decision-making of urban planning schemes.
基金We are grateful to Dr.D.Kaškelytėfor building a comprehensive literature database on OPCPA.We also would like to add the following dedication at the very end of the paper:This article is dedicated to the memory of Professor Algis Petras Piskarskas(1942-2022).
文摘The generation of power-and wavelength-scalable few optical cycle pulses remains one of the major challenges in modern laser physics.Over the past decade,the development of table-top optical parametric chirped pulse amplificationbased systems was progressing at amazing speed,demonstrating excellent performance characteristics in terms of pulse duration,energy,peak power and repetition rate,which place them at the front line of modern ultrafast laser technology.At present,table-top optical parametric chirped pulse amplifiers comprise a unique class of ultrafast light sources,which currently amplify octave-spanning spectra and produce carrier-envelope phase-stable,few optical cycle pulses with multi-gigawatt to multi-terawatt peak powers and multi-watt average powers,with carrier wavelengths spanning a considerable range of the optical spectrum.This article gives an overview on the state of the art of table-top optical parametric chirped pulse amplifiers,addressing their relevant scientific and technological aspects,and provides a short outlook of practical applications in the growing field of ultrafast science.
基金supported in part by grants from the National Institutes of Health (R01CA213149,R01CA241618).
文摘Nonlinear optical imaging is a versatile tool that has been proven to be exceptionally useful in various research fields.However,due to the use of photomultiplier tubes(PMTs),the wide application of nonlinear optical imaging is limited by the incapability of imaging under am-bient light.In this paper,we propose and demonstrate a new optical imaging detection method based on optical parametric amplification(OPA).As a nonlinear optical process,OPA in-trinsically rejects ambient light photons by coherence gating.Periodical poled lithium niobate(PPLN)crystals are used in this study as the media for OPA.Compared to bulk nonlinear optical crystals,PPLN crystals support the generation of OPA signal with lower pump power.Therefore,this characteristic of PPLN crystals is particularly beneficial when using high-repetition-rate lasers,which facilitate high-speed optical signal detection,such as in spec-troscopy and imaging.A PPLN-based OPA system was built to amplify the emitted imaging signal from second harmonic generation(SHG)and coherent anti-Stokes Raman scattering(CARS)microscopy imaging,and the amplified optical signal was strong enough to be detected by a biased photodiode under ordinary room light conditions.With OPA detection,ambient-light-on SHG and CARS imaging becomes possible,and achieves a similar result as PMT detection under strictly dark environments.These results demonstrate that OPA can be used as a substitute for PMTs in nonlinear optical imaging to adapt it to various applications with complex.light ing conditions.
文摘Taking bump-type gas foil bearings as the research object,a deformation model of bump foil and a thin-plate finite element model of top foil were proposed.By solving Reynolds equation and energy equation,the pressure distribution and the temperature distribution of gas films in foil bearings were obtained.Further,a numerical method for calculating the lubrication performance of gas foil bearings with considering the surface roughness was proposed.With a specific example,effects of the surface roughness on the bearing lubrication performance were parametrically studied.The results indicate that rougher journal surface can lead to larger fluctuation of the lubrication performance,while surface roughness of top foil has few effects on the fluctuation.Moreover,the mean values of performance parameters almost remain constant at different values of surface roughness.
文摘This paper introduces an aircraft wing simulation data set(AWSD)created by an automatic workflow based on creating models,meshing.simulating the wing flight flow field solution,and parameterizing solution results.AWSD is a flexible,independent wing collection of simulations with specific engineering requirements.The data set is applicable to handle computer geometry processing tasks.In contrast to the existing 3D model data set,there are some advantages the scale of this data set is not limited by the collection source,the data files have high quality,no defects,redundancy,and other problems,and the models and simulation are all designed for the specific actual engineering demand.Moreover,AWSD has the characteristics of rich information and a similar model structure,which contributes to the construction of the surrogate model.On the other hand,this data set is suitable for advancing research of data mining in computational geometry graphics.To solve the problem that the CFD flows field results are not intuitive,this paper used the resampling method of surface data to sample the result to the model surface,then segmented the re sampled 3D mesh surface,and compared with the diferences among K-means algorithm,Mini_Batch K means algorithm,and Spectral Clustering algorithm.AWSD provides 300 sets of models,meshes,CFD simulation results,and parametric results based on ARAP(As-Rigid-As Posible)and Harmonic mapping for advancing the construction of engineering surrogate models,3D mesh segmentation,surface resampling,and related geometric processing tasks.
基金the National Natural Science Foundation of China(Grant No.11904194).
文摘Spin pumping(SP)and inverse spin Hall effect(ISHE)driven by parametrically-excited dipole-exchange spin waves in a yttrium iron garnet film have been systematically investigated.The measured voltage spectrum exhibits a feature of the field-induced transition from parallel pumping to perpendicular pumping because of the inhomogeneous excitation geometry.Thanks to the high precision of the SP-ISHE detection,two sets of fine structures in the voltage spectrum are observed,which can correspond well to two kinds of critical points in the multimode spin-wave spectrum for magnetic films.One is the q=0 point of each higher-order dispersion branch,and the other is the local minimum due to the interplay between the dipolar and exchange interactions.These fine structures on the voltage spectrum confirm the spin pumping by higher-order dipole-exchange spin-wave modes,and are helpful for probing the multimode spin-wave spectrum.
基金supported by the National Natural Science Foundation of China(No.52075350)the Major Science and Technology Projects of Sichuan Province(No.2022ZDZX0001)the Special City School Strategic Cooperation Project of Sichuan University and Zigong(No.2021CDZG-3).
文摘The nuclear fuel assembly is the core component of a nuclear reactor.In a pressurized water reactor fuel assembly,the top-connection structure connects the top nozzle to the guide thimble.Its performance reliability is essential for the stability of the nuclear fuel assembly.In this study,an assembly-oriented reliability analysis method for top-connection structures is presented by establishing an assembly-oriented top-connection structure parameter modeling method and a nonlinear contact gap and penetration correction method.A reliability model of the top-connection assembly structure,including multiple stochastic design variables,was constructed,and the overall reliability of the top-connection assembly structure was obtained via a Kriging model and Monte Carlo simulation.The acquired experimental data were consistent with real-world failure conditions,which verified the practicability and feasibility of the reliability analysis method proposed in this study.
基金The supports from the Natural Science Research of Jiangsu Higher Education Institutions of China(21KJB580001)the National Natural Science Foundation of China(Grant No.52209162,51979152)+2 种基金Educational Commission of Hubei Province of China(T2020005)Young Top-notch Talent Cultivation Program of Hubei ProvinceJiangxi Provincial Natural Science Foundation(20212BAB214044)。
文摘Reinforced concrete(RC)structures are common in engineering,and usually exposed to air or water,may be subjected to various blast scenarios.This paper aims to investigate the blast resistance of an airbacked RC slab against underwater contact explosions(UWCEs).A detailed numerical model based on CLE method considering explosive,water,air,and RC slab is developed to examine the structural behavior of the air-backed RC slab due to UWCEs.At first,the reliability of the numerical method is validated by comparing the numerical results of an UWCE test with experimental data.Then,the difference in dynamic behavior of air-backed and water-backed RC slabs due to UWCEs is explored with the calibrated model.The results indicate that the blast response of the air-backed slab induced by UWCE is fiercer than that of water-backed slab with equal charge mass.In addition,parametric studies are also conducted to explore the effects of the charge mass,standoff distance,reinforcement spacing,concrete compression strength,and boundary condition on the blast performance of the air-backed RC slab.