Diffusion Bonding of Silicon Carbide Particulate Reinforced 2024 Al Composites

A study has been made on diffusion bonding of SiCp/2024Ai composites by means of pure Al interlayer. In the condition of TB=843 K, PB=16 MPa, tB= 60 min, the diffusion bonded joint, with a shear strength of 235 MPa, was obtained when a 15 μm thick interlayer was used. The results of the shear testing and SEM indicate that fracture of the joint presented characteristics of ductile rupture.

Preparation and Mechanical Properties of-SiC Nanoparticle Reinforced Aluminum Matrix Composite by a Multi-step Powder Metallurgy Process

β-SiC nanoparticle reinforced A1 matrix （nano-SiCp/A1） composite was prepared by a multi- step powder metallurgy strategy including presureless sintering, hot compacting process and hot extrusion. The microstructures of the as-prepared composites were observed by scanning electronic microscopy （SEM）, and the mechanical properties were characterized by tensile strength measurement and Brinell hardness test. The experimental results revealed that the tensile strength of the composite with the addition of 5wt%/3-SIC nanoprtieles could be increased to 215 MPa, increasing by 110% compared with pure A1 matrix. Comparative experiments reflected that theβ-SIC nanoprticles showed significant reinforcement effect than traditional a-SiC micro-sized particles. The preparation process and sintering procedure were investigated to develop a cost effective preparation strategy to fabricate nano-SiCp/A1 composite.

Numerical simulation of thermo-mechanical fatigue properties for particulate reinforced composites

In this paper, a two dimensional Voronoi cell element, formulated with creep, thermal and plastic strain, is applied for the numerical simulation of thermo-mechanical fatigue behavior for particulate reinforced composites. The relation between mechanical fatigue phases and thermal fatigue phases influences the thermo-mechanical fatigue behavior and cyclic creep damage. The topological features of micro-structure in particulate reinforced composites, such as the orientation, depth-width ratio, distribution and volume fraction of inclusions, have a great influence on thermo-mechanical behavior. Some related conclusions are obtained by examples of numerical simulation.

Statistical Analyses of the Strengths of Particulate Reinforced Metal Matrix Composites(PRMMCs)Subjected to Multiple Tensile and Shear Stresses

For design and application of particulate reinforced metal matrix composites(PRMMCs),it is essential to predict the material strengths and understand how do they relate to constituents and microstructural features.To this end,a computational approach consists of the direct methods,homogenization,and statistical analyses is introduced in our previous studies.Since failure of PRMMC materials are often caused by time-varied combinations of tensile and shear stresses,the established approach is extended in the present work to take into account of these situations.In this paper,ultimate strengths and endurance limits of an exemplary PRMMC material,WC-Co,are predicted under three independently varied tensile and shear stresses.In order to cover the entire load space with least amount of weight factors,a new method for generating optimally distributed weight factors in an n dimensional space is formulated.Employing weight factors determined by this algorithm,direct method calculations were performed on many statistically equivalent representative volume elements(SERVE)samples.Through analyzing statistical characteristics associated with results the study suggests a simplified approach to estimate the material strength under superposed stresses without solving the difficult high dimensional shakedown problem.

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF PARTICULATE REINFORCED MATRIX COMPOSITE

TiB2 - particulate- reinforced Ni3 Al composites were prepared by spray a tom-ization co-deposition technique. The reinforcement particulate can be uniformly distributedin matrix alloy, and no interaction would be found at interface between TiB, and Ni,Al.In a word, the composites possess comprehensive mechanical properties.

CHARACTERIZATION OF THERMO-MECHANICAL FATIGUE PROPERTIES FOR PARTICULATE REINFORCED COMPOSITES

A Voronoi cell dement, formulated with creep, thermal and plastic strain was applied for investigation of thermo-mechanical fatigue behavior for particulate reinforced composites. Under the in-phase fatigue loading, the maximum of tensile deformation at the maximum given loading are larger than that at the same maximum under the out-phase fatigue. The stiffness decreases nonlinearly with the increasing of the phase angle, which results in increasing of the area of fatigue loop curve and the decrease in fatigue life. The spatially centralizing of inclusions results in decreasing of the plastic strain amplitude and the area of fatigue loop curve, which will also reduce the consumption of single-circle plastic strain energy and prolong the fatigue life.

Simplification and improvement of prediction model for elastic modulus of particulate reinforced metal matrix composite

In this paper, we proposed a five-zone model to predict the elastic modulus of particulate reinforced metal matrix composite. We simplified the calculation by ignoring structural parameters including particulate shape, arrangement pattern and dimensional variance mode which have no obvious influence on the elastic modulus of a composite, and improved the precision of the method by stressing the interaction of interfaces with pariculates and maxtrix of the composite. The five- zone model can reflect effects of interface modulus on elastic modulus of composite. It overcomes limitations of expressions of rigidity mixed law and flexibility mixed law. The original idea of five zone model is to put forward the particulate/interface interactive zone and matrix/interface interactive zone. By organically integrating the rigidity mixed law and flexibility mixed law, the model can predict the engineering elastic constant of a composite effectively.

Materials Design of Microstructure in Grain Boundary and Second Phase Particles

A concept of microstructure design for materials or materials microstructure engineering is proposed. The argument was suggested based on literature review and. some our new research work on second phase strengthening mechanisms and mechanical property modeling of a particulate reinforced metal matrix composite. Due to development of computer technology, it is possible now for us to establish the relationship between microstructures and properties systematically and quantitatively by analytical and numerical modeling in the research scope of computerization materials. Discussions and examples on intellectual optimization of microstructure are presented on two aspects: grain boundary engineering and optimal geometry of particulate reinforcements in two-phase materials.

SiCp/Al Composites Fabricated by Modified Squeeze Casting Technique

A cost effective method was introduced to fabricate pure aluminum matrix composites reinforced with 20% volume fraction of 3.5 μm SiC particles by squeeze casting followed by hot extrusion. In order to lower volume fraction of the composites, a mixed preform containing pure aluminum powder and the SiC particles was used. The suitable processing parameters for the infiltration of pure aluminum melt into the mixed preform are： melt temperature 800℃, preform temperature 500℃, infiltration pressure 5 MPa, and solidification pressure 50 MPa. Microstructure and properties of the composites in both as-cast and hot extruded states were investigated. The results indicate that hot extrusion can obviously improve the mechanical properties of the composite.

Preparation of 6066/SiC-p composites by multilayer spray deposition

SiC particulate reinforced 6066 aluminium alloy metal matrix composites (MMCs) were prepared by multi layer spray forming. The preparation technology and process parameters were discussed. It is shown that SiC particulate can be continuously and evenly fed and co deposited in the spray forming process. The reciprocally scanning movement of spraying system can make the SiC particulates distribute homogeneously in the composite. The ratio of SiC particulates captured by the metal matrix is influenced by process parameters, especially the metal flow rate. 6066/SiC p composite preforms of d 300 mm×540 mm and tubes with a size of up to d 650/ d 300 mm×1 000 mm were made by the same process. After extrusion and T6 heat treatment, the multi layer spray deposited 6066/SiC p composites can achieve improved properties. [