Energy dissipation mechanism and ballistic characteristic optimization in foam sandwich panels against spherical projectile impact

This study systematically examines the energy dissipation mechanisms and ballistic characteristics of foam sandwich panels(FSP)under high-velocity impact using the explicit non-linear finite element method.Based on the geometric topology of the FSP system,three FSP configurations with the same areal density are derived,namely multi-layer,gradient core and asymmetric face sheet,and three key structural parameters are identified:core thickness(t_(c)),face sheet thickness(t_(f))and overlap face/core number(n_(o)).The ballistic performance of the FSP system is comprehensively evaluated in terms of the ballistic limit velocity(BLV),deformation modes,energy dissipation mechanism,and specific penetration energy(SPE).The results show that the FSP system exhibits a significant configuration dependence,whose ballistic performance ranking is:asymmetric face sheet>gradient core>multi-layer.The mass distribution of the top and bottom face sheets plays a critical role in the ballistic resistance of the FSP system.Both BLV and SPE increase with tf,while the raising tcor noleads to an increase in BLV but a decrease in SPE.Further,a face-core synchronous enhancement mechanism is discovered by the energy dissipation analysis,based on which the ballistic optimization procedure is also conducted and a design chart is established.This study shed light on the anti-penetration mechanism of the FSP system and might provide a theoretical basis for its engineering application.

Ballistic performance of spherical fragments penetrating PCrNi3MoV target plates

PCrNi3MoV steel is a medium-carbon,low-alloy quenched and tempered steel that finds its applications in military gun barrels due to the high wear resistance and ablation resistance.To study the penetration and failure modes of PCrNi3MoV plates impacted by tungsten spheres,tungsten spheres of various diameters(5 mm,8 mm,and 10 mm)were used to impact PCrNi3MoV steel plates with thicknesses of 6 mm,9 mm,and 14 mm.The penetration performance of the spheres was analyzed for different velocities,and the ultimate penetration velocity of the plate was obtained.It was found that the primary failure modes of the PCrNi3MoV plate were compression pitting failure and shear failure.Using the dimensional analysis method,a relationship between the bulge height of the steel plate and the fragment velocity,an equation for the ultimate penetration velocity,and a relationship between the target penetration energy and the fragment velocity were obtained.Then,a projectile-target action index was proposed to describe the process of tungsten spheres with different velocities impacting target plates.The results suggested that under the same thickness of the target plate,a larger-diameter fragment required more kinetic energy to obtain the same ultimate penetration effect as a smaller-diameter fragment.The equations obtained through dimensional analysis predicted values that agreed well with experimental values,indicating that these equations can be applied to engineering applications.

Communication Resources Allocation for Time Delay Reduction of Frequency Regulation Service in High Renewable Penetrated Power System

The high renewable penetrated power system has severe frequency regulation problems.Distributed resources can provide frequency regulation services but are limited by com-munication time delay.This paper proposes a communication resources allocation model to reduce communication time delay in frequency regulation service.Communication device resources and wireless spectrum resources are allocated to distributed resources when they participate in frequency regulation.We reveal impact of communication resources allocation on time delay reduction and frequency regulation performance.Besides,we study communication resources allocation solution in high renewable energy penetrated power systems.We provide a case study based on the HRP-38 system.Results show communication time delay decreases distributed resources'ability to provide frequency regulation service.On the other hand,allocating more communication resources to distributed resources'communica-tion services improves their frequency regulation performance.For power systems with renewable energy penetration above 70%,required communications resources are about five times as many as 30%renewable energy penetrated power systems to keep frequency performance the same.Index Terms-Communication resources allocation,commun-ication time delay,distributed resource,frequency regulation,high renewable energy penetrated power system.

A Possible Configuration with Motor-generator Pair for Renewable Energy Integration

High penetration rates of renewable energy will bring stability problems for the future power grid.One of the critical issues is lack of inertia.In this paper,a synchronous motor-generator pair(MGP)system is proposed as a possible solution for renewable energy integration to enhance inertia and improve grid stability.First,feasibility studies of MGP on inertia,damping,efficiency,and cost are presented.Second,an analytical model is established based on its rotor angle relation.An active power control scheme based on voltage phase difference between renewable energy source and grid is then proposed,and state equations of MGP are derived for small signal stability.Next,two experiments are designed and implemented to verify stable operation and active power regulation of the MGP system.A single-machine infinite bus system is tested to investigate small signal stability and frequency response of MGP.The results show that the MGP system has a solid base in physics and is a feasible solution for providing enough inertia and improving small signal performance in the power grid with high penetration of renewable energy.The paper concludes with a discussion on future research directions to gain a better understanding of MGP.

Energy absorption potential of concrete floors containing secondary （shrinkage and temperature） reinforcements

This paper experimentally investigates the namely, normal density concrete and structural low-density energy absorption potential of two types of concrete floors, concrete, containing secondary （shrinkage and temperature） reinforcements. The test program considered the following secondary reinforcements： 1） traditional welded-wire steel mesh, 2） steel fiber and 3） poly composite fiber. To estimate the extent to which crushing of floor slab materials would help absorb energy, a series of concrete penetration tests employing patch loading was undertaken on scaled down model slabs. Each concrete-secondary reinforcement combination considered slabs of 50 mm in depth with square plan dimensions ranging from 50 to 500 mm, resulting in a total of 30 test specimens. The first part of the paper discusses the test specimens, the test setup, and the test procedure. The second part of the paper presents the experimental results and establishes the energy absorption of different concrete- secondary reinforcement combinations. Sieve analysis results of the crushed specimens were used to derive a ＂work index＂ value that relates the pulverized particle size distributions to energy inputs. The work index values of concrete-secondary reinforcement systems can be used to assess the energy dissipation potential associated with such floor slabs in buildings undergoing progressive collapse. The results indicate that floors with secondary reinforcements could play an important role in helping arrest global progressive collapse.

Applying Power Margin Tracking Droop Control to Flexible Operation in Multi-terminal DC Collector Systems of Renewable Generation

An emerging multi-terminal looped DC(MTDC)collector system is now advocated for collecting and transferring large-scale renewable generation.However,it remains an open question as to improving the cooperative control capability of looped converter stations for flexible and robust response to renewable grid-connection fluctuation.This paper addresses this problem with a novel Power Margin Tracking(PMT)droop control and its corresponding system-level control strategy from the perspective of optimal dispatch of the power system.By introducing a power margin correction factor into the droop coefficient,the converter station can make self-adaptive regulations according to its actual available power margin.For operation verification,a multi-period optimal operation model and a four-terminal simulation model is built to provide optimal control parameters and real-time operation states of converter stations,where the power flow model of the looped MTDC grid with renewables generation is considered.The case results prove that the proposed control strategy can improve the cooperative operation capability of multiple converter stations,mitigating grid-connected power fluctuation.It can effectively reduce the DC voltage deviation to enhance the operation stability of the MTDC grid.The operational robustness of the proposed control strategy under“N−1”fault cases is verified as well.