Ballistic performance of additive manufacturing 316l stainless steel projectiles based on topology optimization method

Material and structure made by additive manufacturing(AM)have received much attention lately due to their flexibility and ability to customize complex structures.This study first implements multiple objective topology optimization simulations based on a projectile perforation model,and a new topologic projectile is obtained.Then two types of 316L stainless steel projectiles(the solid and the topology)are printed in a selective laser melt(SLM)machine to evaluate the penetration performance of the projectiles by the ballistic test.The experiment results show that the dimensionless specific kinetic energy value of topologic projectiles is higher than that of solid projectiles,indicating the better penetration ability of the topologic projectiles.Finally,microscopic studies(scanning electron microscope and X-ray micro-CT)are performed on the remaining projectiles to investigate the failure mechanism of the internal structure of the topologic projectiles.An explicit dynamics simulation was also performed,and the failure locations of the residual topologic projectiles were in good agreement with the experimental results,which can better guide the design of new projectiles combining AM and topology optimization in the future.

Bamboo Fiber Modified Asphalt Mixture Proportion Design and Road Performances Based on Response Surface Method

In order to comprehensively utilize the remaining bamboo residue of bamboo products,this paper presents a research on recycling the bamboo fibers from bamboo residue for improving the performance of the asphalt mixtures.First of all,the basic performance parameters of sinocalamus affinis fiber,phyllostachys pubescens fiber,green bamboo fiber were tested and analyzed,and the optimal content and length were put forward.Then,the mix ratio design of the bamboo fiber modified asphalt mixture was further designed through the response surface method,and was verified the rationality of the mix ratio.Finally,the mixture specimens were made according to the experimental design mix ratio,and the high temperature,low temperature performance and moisture susceptibility of the bamboo fiber modified mixtures asphalt were tested.The results showed that the high temperature performance,low temperature performance and moisture susceptibility of bamboo fiber modified asphalt mixtures were improved compared with the performance of SBS modified asphalt mixture.When the length of bamboo fiber is 7.25 mm and the content of 0.22%,the road performance of the asphalt mixture was optimal.Consequentially,the decomposition of bamboo residue into bamboo fiber and its application in asphalt pavement can improve the reuse of bamboo waste,with remarkable environmental benefits and great promotion value.

Design and optimization of fluid lubricated bearings operated with extreme working performances——a comprehensive review

Fluid lubricated bearings have been widely adopted as support components for high-end equipment in metrology,semiconductor devices,aviation,strategic defense,ultraprecision manufacturing,medical treatment,and power generation.In all these applications,the equipment must deliver extreme working performances such as ultraprecise movement,ultrahigh rotation speed,ultraheavy bearing loads,ultrahigh environmental temperatures,strong radiation resistance,and high vacuum operation,which have challenged the design and optimization of reliable fluid lubricated bearings.Breakthrough of any related bottlenecks will promote the development course of high-end equipment.To promote the advancement of high-end equipment,this paper reviews the design and optimization of fluid lubricated bearings operated at typical extreme working performances,targeting the realization of extreme working performances,current challenges and solutions,underlying deficiencies,and promising developmental directions.This paper can guide the selection of suitable fluid lubricated bearings and optimize their structures to meet their required working performances.

Optimal Design of the Modular Joint Drive Train for Enhancing Cobot Load Capacity and Dynamic Performance

Automation advancements prompts the extensive integration of collaborative robot(cobot)across a range of industries.Compared to the commonly used design approach of increasing the payload-to-weight ratio of cobot to enhance load capacity,equal attention should be paid to the dynamic response characteristics of cobot during the design process to make the cobot more flexible.In this paper,a new method for designing the drive train parameters of cobot is proposed.Firstly,based on the analysis of factors influencing the load capacity and dynamic response characteristics,design criteria for both aspects are established for cobot with all optimization design criteria normalized within the design domain.Secondly,with the cobot in the horizontal pose,the motor design scheme is discretized and it takes the joint motor diameter and gearbox speed ratio as optimization design variables.Finally,all the discrete values of the optimization objectives are obtained through the enumeration method and the Pareto front is used to select the optimal solution through multi-objective optimization.Base on the cobot design method proposed in this paper,a six-axis cobot is designed and compared with the commercial cobot.The result shows that the load capacity of the designed cobot in this paper reaches 8.4 kg,surpassing the 5 kg load capacity commercial cobot which is used as a benchmark.The minimum resonance frequency of the joints is 42.70 Hz.

Design methodology of a mini-missile considering flight performance and guidance precision

The design of mini-missiles(MMs)presents several novel challenges.The stringent mission requirement to reach a target with a certain precision imposes a high guidance precision.The miniaturization of the size of MMs makes the design of the guidance,navigation,and control(GNC)have a larger-thanbefore impact on the main-body design(shape,motor,and layout design)and its design objective,i.e.,flight performance.Pursuing a trade-off between flight performance and guidance precision,all the relevant interactions have to be accounted for in the design of the main body and the GNC system.Herein,a multi-objective and multidisciplinary design optimization(MDO)is proposed.Disciplines pertinent to motor,aerodynamics,layout,trajectory,flight dynamics,control,and guidance are included in the proposed MDO framework.The optimization problem seeks to maximize the range and minimize the guidance error.The problem is solved by using the nondominated sorting genetic algorithm II.An optimum design that balances a longer range with a smaller guidance error is obtained.Finally,lessons learned about the design of the MM and insights into the trade-off between flight performance and guidance precision are given by comparing the optimum design to a design provided by the traditional approach.

Design,preparation,application of advanced array structured materials and their action mechanism analyses for high performance lithium-sulfur batteries

Lithium-sulfur battery(LSB)has brought much attention and concern because of high theoretical specific capacity and energy density as one of main competitors for next-generation energy storage systems.The widely commercial application and development of LSB is mainly hindered by serious“shuttle effect”of lithium polysulfides(Li PSs),slow reaction kinetics,notorious lithium dendrites,etc.In various structures of LSB materials,array structured materials,possessing the composition of ordered micro units with the same or similar characteristics of each unit,present excellent application potential for various secondary cells due to some merits such as immobilization of active substances,high specific surface area,appropriate pore sizes,easy modification of functional material surface,accommodated huge volume change,enough facilitated transportation for electrons/lithium ions,and special functional groups strongly adsorbing Li PSs.Thus many novel array structured materials are applied to battery for tackling thorny problems mentioned above.In this review,recent progresses and developments on array structured materials applied in LSBs including preparation ways,collaborative structural designs based on array structures,and action mechanism analyses in improving electrochemical performance and safety are summarized.Meanwhile,we also have detailed discussion for array structured materials in LSBs and constructed the structure-function relationships between array structured materials and battery performances.Lastly,some directions and prospects about preparation ways,functional modifications,and practical applications of array structured materials in LSBs are generalized.We hope the review can attract more researchers'attention and bring more studying on array structured materials for other secondary batteries including LSB.

Reliable Space Pursuing for Reliability-based Design Optimization with Black-box Performance Functions

Reliability-based design optimization （RBDO） is intrinsically a double-loop procedure since it involves an overall optimization and an iterative reliability assessment at each search point. Due to the double-loop procedure, the computational expense of RBDO is normally very high. Current RBDO research focuses on problems with explicitly expressed performance functions and readily available gradients. This paper addresses a more challenging type of RBDO problem in which the performance functions are computation intensive. These computation intensive functions are often considered as a ＂black-box＂ and their gradients are not available or not reliable. On the basis of the reliable design space （RDS） concept proposed earlier by the authors, this paper proposes a Reliable Space Pursuing （RSP） approach, in which RDS is first identified and then gradually refined while optimization is performed. It fundamentally avoids the nested optimization and probabilistic assessment loop. Three well known RBDO problems from the literature are used for testing and demonstrating the effectiveness of the proposed RSP method.

Light-Weight Design Method for Force-Performance-Structure of Complex Structural Part Based Co-operative Optimization

A light?weight design method of integrated structural topology and size co?optimization for the force?performance?structure of complex structural parts is presented in this paper. Firstly, the supporting function of a complex structural part is built to map the force transmission, where the force exerted areas and constraints are considered as connecting structure and the structural configuration, to determine the part performance as well as the force routines. Then the connecting structure design model, aiming to optimize the static and dynamic performances on connection configuration, is developed, and the optimum design of the characteristic parameters is carried out by means of the collaborative optimization method, namely, the integrated structural topology optimization and size optimization. In this design model, the objective is to maximize the connecting stiffness. Based on the relationship between the force and the structural configuration of a part, the optimal force transmission routine that can meet the performance requirements is obtained using the structural topology optimization technology. Accordingly, the light?weight design of conceptual configuration for complex parts under multi?objective and multi?condition can be realized. Finally, based on the proposed collaborative optimization design method, the optimal performance and optimal structure of the complex parts with light weight are realized, and the reasonable structural unit configuration and size charac?teristic parameters are obtained. A bed structure of gantry?type machining center is designed by using the proposed light?weight structure design method in this paper, as an illustrative example. The bed after the design optimization is lighter 8% than original one, and the rail deformation is reduced by 5%. Moreover, the lightweight design of the bed is achieved with enhanced performance to show the effectiveness of the proposed method.

Design of Small Stone Asphalt Mixture based on Anti-skidding Performance

Small stone asphalt mixture（SSAM） was designed by Bailey method and coarse aggregate voids-filling method.The optimum asphalt content was determined by Marshal test.Surface texture depth for SSAM with different voidage,and the BPN of SSAM and SMA before after wet track abrasion were measured.The experimental results indicate that the surface texture depth increases with the decreasing of asphalt aggregate ratio.The SSAM with the optimal asphalt content has a good skid resistance.BPN of asphalt mixture decreases with the increasing of wearing time,but the extent of reduction is different.The reduction rate of BPN for SSAM is smaller than that of SMA,indicating that SSAM has a good skid resistance attenuation capacity.Finally,the other properties of SSAM are also evaluated,showing that the splitting strength and modulus and SSAM are higher than those of SMA,and the other properties of SSAM,such as high-temperature performance and water stability can also satisfy the technical requirements.

Performance-based seismic design of nonstructural building components:The next frontier of earthquake engineering

With the development and implementation of performance-based earthquake engineering,harmonization of performance levels between structural and nonstructural components becomes vital. Even if the structural components of a building achieve a continuous or immediate occupancy performance level after a seismic event,failure of architectural,mechanical or electrical components can lower the performance level of the entire building system. This reduction in performance caused by the vulnerability of nonstructural components has been observed during recent earthquakes worldwide. Moreover,nonstructural damage has limited the functionality of critical facilities,such as hospitals,following major seismic events. The investment in nonstructural components and building contents is far greater than that of structural components and framing. Therefore,it is not surprising that in many past earthquakes,losses from damage to nonstructural components have exceeded losses from structural damage. Furthermore,the failure of nonstructural components can become a safety hazard or can hamper the safe movement of occupants evacuating buildings,or of rescue workers entering buildings. In comparison to structural components and systems,there is relatively limited information on the seismic design of nonstructural components. Basic research work in this area has been sparse,and the available codes and guidelines are usually,for the most part,based on past experiences,engineering judgment and intuition,rather than on objective experimental and analytical results. Often,design engineers are forced to start almost from square one after each earthquake event: to observe what went wrong and to try to prevent repetitions. This is a consequence of the empirical nature of current seismic regulations and guidelines for nonstructural components. This review paper summarizes current knowledge on the seismic design and analysis of nonstructural building components,identifying major knowledge gaps that will need to be filled by future research. Furthermore,considering recent trends in earthquake engineering,the paper explores how performance-based seismic design might be conceived for nonstructural components,drawing on recent developments made in the field of seismic design and hinting at the specific considerations required for nonstructural components.

A Simple Mix Proportion Design Method Based on Frost Durability for Recycled High Performance Concrete Using Fully Coarse Recycled Aggregate

Durability design of recycled high performance concrete（RHPC） is fundamental for improving the use rate and level of concrete waste as coarse recycled aggregate（CRA）. We discussed a frostdurability-based mix proportion design method for RHPC using 100 % CRA and natural sand. Five groups of RHPC mixes with five strength grades（40, 50, 60, 70 and 80 MPa） were produced using CRA with four quality classes, and their workability, 28 d compressive strengths and frost resistances（measured by the compressive strength loss ratio and the relative dynamic modulus of elasticity） were tested. Relationships between the 28 d compressive strength, the frost resistance and the CRA quality characteristic parameter, water absorption, were then developed. The criterion of a CRA maximum water absorption limit value for RHPC was suggested, independent of its source and quality class. The results show that all RHPC mixes achieve the expected target workability, strength, and frost durability. The research results demonstrate that the application of the proposed method does not require trial testing prior to use.

New Zealand Advances in Performance-Based Seismic Design

This paper provides a summary of the objectives and principles which underpin the 2004 edition of the New Zealand earthquake design standard, AS/NZS 1170 Part 5. As with many modern earthquake design standards, the New Zealand earthquake design standard recognizes that earthquake resistant design that only addresses life safety goals without addressing both operational continuity of essential facilities and damage control, falls short of public expectations. Such standards not longer meet societal expectations. The paper outlines how these issues have been addressed within New Zealand, and some of the issues addressed when preparing appendices to the standard to provide guidance for materials standard writers to ensure consistency with the proposed approach. Recognizing the significance of non-structural components and parts of buildings in both damage control and operational continuity has been an important step forward in attaining the performance levels required.

PERFORMANCE-BASED INTELLIGENT RESOURCE DESCRIPTION MODEL FOR INTERNET-BASED PRODUCT DESIGN

Issues on intelligent resource description and multiple intelligent resources integration for lntemet based collaborative design are analyzed. A performance-based intelligent resource description model for lnternet-based product design is proposed, which can help to create, store, manipulate and exchange intelligent resource description information for applications, tools and systems in Interact-based product design. A method to integrate multiple intelligent resources to fulfill a complex product design and analysis via lntemet is also proposed. A real project for improving the bearing system design of a turbo-expander with many intelligent resources in prominent universities is presented as a case study.

Peak displacement patterns for the performance-based seismic design of steel eccentrically braced frames

Performance-based seismic design(PBSD) aims to assess structures at different damage states. Since damage can be directly associated to displacements, seismic design with consideration of displacement seems to be logical. In this study, simple formulae to estimate the peak floor displacement patterns of eccentrically braced frames(EBFs) at different performance levels subjected to earthquake ground motions are proposed. These formulae are applicable in a PBSD and especially in direct displacement-based design(DDBD). Parametric study is conducted on a group of 30 EBFs under a set of 15 far field and near field accelerograms which they scaled to different amplitudes to adapt various performance levels. The results of thousands of nonlinear dynamic analyses of EBFs have been post-processed by nonlinear regression analysis in order to recognize the major parameters that influence the peak displacement pattern of these frames. Results show that suggested displacement patterns have relatively good agreement with those acquired by an exact nonlinear dynamic analysis.

Redesigning the Model of Book Evaluation in the Polish Performance-based Research Funding System

Purpose: This study aims to present the key systemic changes in the Polish book evaluation model to focus on the publisher list, as inspired by the Norwegian Model. Design/methodology/approach: In this study we reconstruct the framework of the 2010 and 2018 models of book evaluation in Poland within the performance-based research funding system. Findings: For almost 20 years the book evaluation system in Poland has been based on the verification of various technical criteria(e.g. length of the book). The new 2018 model is based on the principle of prestige inheritance(a book is worth as much as its publisher is) and is inspired by the publisher list used in the Norwegian Model. In this paper, we argue that this solution may be a more balanced policy instrument than the previous 2010 model in which neither the quality of the publisher nor the quality of the book played any role in the evaluation.Research limitations: We work from the framework of the 2018 model of book evaluation specified in the law on higher education and science from 20 July 2018, as implementation acts are not available yet. Practical implications: This study may provide a valuable point of reference on how structural reforms in the research evaluation model were implemented on a country level. The results of this study may be interesting to policy makers, stakeholders and researchers focused on science policy. Originality/value: This is the very first study that presents the new framework of the Polish research evaluation model and policy instruments for scholarly book evaluation. We describe what motivated policy makers to change the book evaluation model, and what arguments were explicitly raised to argue for the new solution.

Ground Motion and Site Effects on Performance-Based Design

The objective of Performance-Based Earthquake Engineering （PBEE） is the analysis of performance objectives with a specified annual probability of exceedance. Increasingly undesirable performance is caused by increasing levels of strong ground motion having decreasing annual probabilities of exceedance. The development of this methodology includes three steps： （1） evaluation of the distribution of ground motion at a site; （2） evaluation of the distribution of system response; （3） evaluation of the probability of exceeding decision variables within a given time period, given appropriate damage measures. The work has taken a systematic approach to determine the impact of increasing levels of detail in site characterization on the accuracy of ground motion and site effects predictions. Complementary studies have investigated the use of the following models for evaluating site effects： （1） amplification factors defined on the basis of generalized site categories, （2） one-dimensional ground response analysis, and （3） two-dimensional ground response analysis for surface topography on ground motion. The paper provides a brief synthesis of ground motion and site effects analysis procedures within a Performance-Based Design framework. It focuses about the influence on the evaluation of site effects in some active regions by different shear waves velocity measurements Down Hole （D-H）, Cross Hole （C-H）, Seismic Dilatometer Marchetti Test （SDMT） and by different variation of shear modulus and damping ratio with strain level and depth from different laboratory dynamic tests for soil characterization： Resonant Column Test （RCT）, Cyclic Loading Torsional Shear Test （CLTST）.

MODEL OF FLIGHT TECHNICAL ERROR IN SYMMETRICAL PLANE FOR PERFORMANCE BASED NAVIGATION

In the performance based navigation（PBN）,the flight technical error（FTE）and the navigation system error（NSE）are two main parts of total system error（TSE）.The implementation of PBN requires pre-flight prediction and en-route short-term dynamical prediction of TSE.Once the sum of predicted FTE and NSE is greater than the specified PBN value,PBN cannot operate.Thus,it requires accurate modeling and thorough analysis of the two main contributors.Multiple-input multiple-output（MIMO）longitudinal flight control system of ARIC model is designed using the linear quadratic Gaussian and loop transfer recovery（LQG/LTR）method,and FTE in symmetrical plane of aircraft is analyzed during the turbulence disturbed approach.The error estimation mapping function of FTE in symmetrical plane and its bound estimation model are proposed based on the singular value theory.The model provides an approach based on the forming mechanism of FTE,rather than the costly flight test and the data fitting.Real-data based simulation validates the theoretical analysis of FTE in symmetrical plane.It also shows that FTE is partially caused by the turbulence fluctuation disturbance when the automatic flight control system（AFCS）is engaged and increases with escalating the environmental turbulence intensity.

Satellite constellation design with genetic algorithms based on system performance

Satellite constellation design for space optical systems is essentially a multiple-objective optimization problem. In this work, to tackle this challenge, we first categorize the performance metrics of the space optical system by taking into account the system tasks（i.e., target detection and tracking）. We then propose a new non-dominated sorting genetic algorithm（NSGA） to maximize the system surveillance performance. Pareto optimal sets are employed to deal with the conflicts due to the presence of multiple cost functions. Simulation results verify the validity and the improved performance of the proposed technique over benchmark methods.

Logic-based Reset Adaptation Design for Improving Transient Performance of Nonlinear Systems

In this paper, logic-based switching and resetting principles are presented to devise adaptive control laws for a class of uncertain nonlinear systems in order to ensure both the transient bound and the asymptotical convergence of the state. A novel supervisor is constructed to decide when to reset the estimation parameter with the pre-given estimation value. A benchmark example is presented to demonstrate the effectiveness of the approach. © 2014 Chinese Association of Automation.

Performance-Based Design through Implementation of FEMA P-58 Methodology in Developing Countries

This paper investigates a simple approach proposed towards performance-based earthquake engineering (PBEE) which has potential applications to the performance-based design (PBD) and performance-based assessment (PBA) fields. The simple method of PBEE encompasses three areas of seismic risk which include seismic hazard, structural analysis, and loss models. The aim of the PBEE process, entitled as FEMA P-58, is to present essential data needed to make a rational decision regarding predicted performance, where various sources of uncertainties are involved. In developing countries, the lack of suitable real ground motions corresponding to site characteristics and seismicity particularly for larger intensities and the scarcity of demands, which makes it hard to identify the seismic capacity of a structure, is the main our motivation of using the FEMA method. In this paper, the method of FEMA P-58 is investigated, in terms of available tools and required data, in such a way that it will be applicable for developing countries which are located in high seismic hazard zones. To achieve this goal, three steel moment-resisting buildings with low and high ductility, and three steel braced-frame buildings are selected as case studies. The mean annual loss is estimated by the available software, Performance Assessment Calculation Tool (PACT). The achieved results, i.e. the loss curves, will provide a simple means by which the engineers can quantify and communicate seismic performance to other stakeholders. In the case study buildings, the braced one has less annual losses in comparison with other investigated cases, and the structure with high ductility can be considered as the next ones. Execution cost of each building should be considered by contractors. Also, seismic fragility curves of structures for various limit states, as well, the corresponding loss models are identified as the most essential data towards application of the investigated PBEE process.