Green synthesis of ZSM-5 using silica fume and catalytic co-cracking of lignin and plastics for production of monocyclic aromatics

ZSM-5 with hierarchical pore structure was synthesized by a simple two-step hydrothermal crystallization from silica fume without using any organic ammonium templates.The synthesized ZSM-5 were oval shaped particles with a particle size about 2.0 μm and weak acid-dominated with proper Brønsted(B)and Lewis(L)acid sites.The ZSM-5 was used for catalytic co-cracking of n-octane and guaiacol,lowdensity polyethylene(LDPE)and alkali lignin(AL)to enhance the production of benzene,toluene,ethylbenzene and xylene(BTEX).The most significant synergistic effect occurred at n-octane/guaiacol at 1:1 and LDPE/AL at 1:3,under the condition,the achieved BTEX selectivity were 24%and 33%(mass)higher than the calculated values(weighted average).The highest BTEX selectivity reached 88.5%,which was 3.7%and 54.2%higher than those from individual cracking LDPE and AL.The synthesized ZSM-5 exhibited superior catalytic performance compared to the commercial ZSM-5,indicating potential application prospect.

Mixed plastics waste valorization to high-added value products via thermally induced phase separation and spin-casting

Plastic waste is an underutilized resource that has the potential to be transformed into value-added materials.However,its chemical diversity leads to cost-intensive sorting techniques,limiting recycling and upcycling opportunities.Herein,we report an open-loop recycling method to produce graded feedstock from mixed polyolefins waste,which makes up 60%of total plastic waste.The method uses heat flow scanning to quantify the composition of plastic waste and resolves its compatibility through controlled dissolution.The resulting feedstock is then used to synthesize blended pellets,porous sorbents,and superhydrophobic coatings via thermally induced phase separation and spin-casting.The hybrid approach broadens the opportunities for reusing plastic waste,which is a step towards creating a more circular economy and better waste management practices.

Low-Density Microplastics in Recreational Parks of Al Ain, United Arab Emirates: Abundance, Composition, and Potential Effects on Soil Health

Microplastics (MPs) have been an emerging concern due to their harmful effects on the ecosystem and are ubiquitous in various habitats, from marine to terrestrial environments. However, studies on the presence of MPs in recreational areas are limited. One of the previous works has reported that urban recreational parks are considered “sinks” for plastic debris, including MPs. In this study, low-density MPs (LD-MPs) in soil samples collected from recreational parks of Al Ain, United Arab Emirates (UAE) were isolated by density flotation method. Results showed that these parks have varying levels of LD-MPs caused by various anthropogenic activities, such as sludge use and application of reclaimed water from wastewater treatment facilities in those areas. These plastic particles were isolated in 87% of the soil samples, with an average concentration of 1550 ± 340 MPs/kg. Predominantly, these comprised large LD-MPs (300 - 5000 μm), with red and blue being the most common colors. Fourier transform infrared (FTIR) spectroscopy identified possible synthetic polymers, including polyethylene and polypropylene. Additionally, a negative correlation was observed between LD-MP concentration and soil pH and moisture content, indicating potential adverse effects on soil health. These findings highlight the need for monitoring and managing microplastic pollution in urban recreational areas to mitigate its ecological impacts.

A Unifi ed View of Carbon Neutrality:Solar-Driven Selective Upcycling of Waste Plastics

With the rapid development of plastic production and consumption globally,the amount of post-consumer plastic waste has reached levels that have posed environmental threats.Considering the substantial CO_(2)emissions throughout the plastic lifecycle from material production to its disposal,photocatalysis is considered a promising strategy for eff ective plastic recycling and upcycling.It can upgrade plastics into value-added products under mild conditions using solar energy,realizing zero carbon emissions.In this paper,we explain the basics of photocatalytic plastic reformation and underscores plastic feedstock reformation pathways into high-value-added products,including both degradation into CO_(2)followed by reformation and direct reformation into high-value-added products.Finally,the current applications of transforming plastic waste into fuels,chemicals,and carbon materials and the outlook on upcycling plastic waste by photocatalysis are presented,facilitating the realization of carbon neutrality and zero plastic waste.

Promoting sustainable consumption and circular economy:the intention of Vietnamese youth consumers to purchase products made from recycled plastics

Recycling is viewed as a key component in a circular economy and serves as an ideal solution for promoting sustainability.During the global plastic crisis,plastic recycling practices have been adopted worldwide,leading to the production of various products made from recycled plastics(PRP).Nevertheless,a gap persists between consumption and demand for such products,which is primarily attributed to a lack of comprehension from the consumer perspective.Given the pivotal role consumers play in the adoption of these products,this study explores consumers’intentions to purchase PRP.This is particularly significant in Vietnam,which is an emerging economy aspiring to achieve the objectives of a circular economy and sustainable development.Utilizing an integrated cognitive-emotional framework comprising the Valence Theory and the Norm Activation Model,data from 564 Vietnamese students were gathered and analyzed using structural equation modeling.The results show that awareness of consequences is a major driver of consumer purchase intentions,followed by perceived ease of application and monetary incentives.The results also indicate that health concerns have the strongest effect on purchase intention and in the negative side,meaning that the health-related risk is the primary concern for consumers during the decision-making process.This research holds substantial value for academics and managers,as it aids in the theoretical exploration and the formulation of strategies to improve consumer acceptance of PRP.

Impacts of Micro- and Nano-Plastics on Soil Properties and Plant Production in Agroecosystems: A Mini-Review

Micro- and nano-plastics (MNPs) are tiny plastic particles resulting from plastic product degradation. Soil MNPs have been identified as potential influential factors affecting various soil properties and crop biomass productivity. This mini-review provides a synthesis of recent findings concerning their effects on soil physicochemical properties, microorganisms, organic carbon content, soil nutrients, greenhouse gas emissions, soil fauna, and their impacts on plant ecophysiology, growth, and production. The results indicate that MNPs may markedly impede soil aggregation ability, increase porosity, decrease soil bulk density, enhance water retention capacity, influence soil pH and electrical conductivity, and escalate soil water evaporation. Exposure to MNPs may predominantly induce changes in soil microbial composition, reducing the diversity and complexity of microbial communities and microbial activity while enhancing soil organic carbon stability, influencing soil nutrient dynamics, and stimulating organic carbon decomposition and denitrification processes, leading to elevated soil respiration and methane emissions, and potentially decreasing soil nitrous oxide emission. Additionally, MNPs may adversely affect soil fauna, diminish seed germination rates, promote plant root growth, yet impair plant photosynthetic efficacy and biomass productivity. These findings contribute to a better understanding of the impacts and mechanistic foundations of MNPs. Future research avenues are suggested to further explore the impacts and economic implications.

Wax from Pyrolysis of Waste Plastics as a Potential Source of Phase Change Material for Thermal Energy Storage

Over the past half-century, plastic consumption has grown rapidly due to its versatility, low cost, and unrivaled functional properties. Among the diff erent implemented strategies for recycling waste plastics, pyrolysis is deemed the most economical option. Currently, the wax obtained from the pyrolysis of waste plastics is mainly used as a feedstock to manufacture chemicals and fuels or added to asphalt for pavement construction, with no other applications of wax being reported. Herein, the thermal pyrolysis of three common waste polyolefin plastics: high-density polyethylene(HDPE), low-density polyethylene(LDPE), and polypropylene(PP), was conducted at 450 ℃. The waste plastics-derived waxes were characterized and studied for a potential new application: phase change materials(PCMs) for thermal energy storage(TES). Gas chromatography–mass spectrometry analysis showed that paraffin makes up most of the composition of HDPE and LDPE waxes, whereas PP wax contains a mixture of naphthene, isoparaffin, olefin, and paraffin. Diff erential scanning calorimetry(DSC) analysis indicated that HDPE and LDPE waxes have a peak melting temperature of 33.8 ℃ and 40.3 ℃, with a relatively high latent heat of 103.2 J/g and 88.3 J/g, respectively, whereas the PP wax was found to have almost negligible latent heat. Fourier transform infrared spectroscopy and DSC results revealed good chemical and thermal stability of HDPE and LDPE waxes after 100 cycles of thermal cycling. Performance evaluation of the waxes was also conducted using a thermal storage pad to understand their thermoregulation characteristics for TES applications.

Ni-catalyzed carbon–carbon bonds cleavage of mixed polyolefin plastics waste

The inert carbon–carbon(C–C) bonds cleavage is a main bottleneck in the chemical upcycling of recalcitrant polyolefin plastics waste. Here we develop an efficient strategy to catalyze the complete cleavage of C–C bonds in mixed polyolefin plastics over non-noble metal catalysts under mild conditions. The nickelbased catalyst involving Ni_(2)Al_(3) phase enables the direct transformation of mixed polyolefin plastics into natural gas, and the gas carbon yield reaches up to 89.6%. Reaction pathway investigation reveals that natural gas comes from the stepwise catalytic cleavage of C–C bonds in polypropylene, and the catalyst prefers catalytic cleavage of terminal C–C bond in the side-chain with the low energy barrier.Additionally, our developed approach is evaluated by the technical economic analysis for an economically competitive production process.

Neural stem cells promote neuroplasticity: a promising therapeutic strategy for the treatment of Alzheimer’s disease

Recent studies have demonstrated that neuroplasticity,such as synaptic plasticity and neurogenesis,exists throughout the normal lifespan but declines with age and is significantly impaired in individuals with Alzheimer’s disease.Hence,promoting neuroplasticity may represent an effective strategy with which Alzheimer’s disease can be alleviated.Due to their significant ability to self-renew,differentiate,and migrate,neural stem cells play an essential role in reversing synaptic and neuronal damage,reducing the pathology of Alzheimer’s disease,including amyloid-β,tau protein,and neuroinflammation,and secreting neurotrophic factors and growth factors that are related to plasticity.These events can promote synaptic plasticity and neurogenesis to repair the microenvironment of the mammalian brain.Consequently,neural stem cells are considered to represent a potential regenerative therapy with which to improve Alzheimer’s disease and other neurodegenerative diseases.In this review,we discuss how neural stem cells regulate neuroplasticity and optimize their effects to enhance their potential for treating Alzheimer’s disease in the clinic.

Upcycling plastic wastes into value-added products via electrocatalysis and photoelectrocatalysis

Plastic,renowned for its versatility,durability,and cost-effectiveness,is indispensable in modern society.Nevertheless,the annual production of nearly 400 million tons of plastic,coupled with a recycling rate of only 9%,has led to a monumental environmental crisis.Plastic recycling has emerged as a vital response to this crisis,offering sustainable solutions to mitigate its environmental impact.Among these recycling efforts,plastic upcycling has garnered attention,which elevates discarded plastics into higher-value products.Here,electrocatalytic and photoelectrocatalytic treatments stand at the forefront of advanced plastic upcycling.Electrocatalytic or photoelectrocatalytic treatments involve chemical reactions that facilitate electron transfer through the electrode/electrolyte interface,driven by electrical or solar energy,respectively.These methods enable precise control of chemical reactions,harnessing potential,current density,or light to yield valuable chemical products.This review explores recent progress in plastic upcycling through electrocatalytic and photoelectrocatalytic pathways,offering promising solutions to the plastic waste crisis and advancing sustainability in the plastics industry.

Lymphatic plastic bronchitis and primary chylothorax: A study based on computed tomography lymphangiography

BACKGROUND This study presents an evaluation of the computed tomography lymphangio-graphy(CTL)features of lymphatic plastic bronchitis(PB)and primary chylotho-rax to improve the diagnostic accuracy for these two diseases.AIM To improve the diagnosis of lymphatic PB or primary chylothorax,a retrospective analysis of the clinical features and CTL characteristics of 71 patients diagnosed with lymphatic PB or primary chylothorax was performed.METHODS The clinical and CTL data of 71 patients(20 with lymphatic PB,41 with primary chylothorax,and 10 with lymphatic PB with primary chylothorax)were collected retrospectively.CTL was performed in all patients.The clinical manifestations,CTL findings,and conventional chest CT findings of the three groups of patients were compared.The chi-square test or Fisher's exact test was used to compare the differences among the three groups.A difference was considered to be statistically significant when P<0.05.RESULTS(1)The percentages of abnormal contrast medium deposits on CTL in the three groups were as follows:Thoracic duct outlet in 14(70.0%),33(80.5%)and 8(80.0%)patients;peritracheal region in 18(90.0%),15(36.6%)and 8(80.0%)patients;pleura in 6(30.0%),33(80.5%)and 9(90.0%)patients;pericardium in 6(30.0%),6(14.6%)and 4(40.0%)patients;and hilum in 16(80.0%),11(26.8%)and 7(70.0%)patients;and(2)the abnormalities on conven-tional chest CT in the three groups were as follows:Ground-glass opacity in 19(95.0%),18(43.9%)and 8(80.0%)patients;atelectasis in 4(20.0%),26(63.4%)and 7(70.0%)patients;interlobular septal thickening in 12(60.0%),11(26.8%)and 3(30.0%)patients;bronchovascular bundle thickening in 14(70.0%),6(14.6%)and 4(40.0%)patients;localized mediastinal changes in 14(70.0%),14(34.1%),and 7(70.0%)patients;diffuse mediastinal changes in 6(30.0%),5(12.2%),and 3(30.0%)patients;cystic lesions in the axilla in 2(10.0%),6(14.6%),and 2(20.0%)patients;and cystic lesions in the chest wall in 0(0%),2(4.9%),and 2(4.9%)patients.CONCLUSION CTL is well suited to clarify the characteristics of lymphatic PB and primary chylothorax.This method is an excellent tool for diagnosing these two diseases.

Making Plastics Greener and More Useful

Scientists from the Changchun Institute of Applied Chemistry of the Chinese Academy of Sciences(CAS)have developed a new way to make plastics to make it possible to be degradable in ambient environment with proper lighting.This move could help reduce plastic pollution.The new approach produces plastics from ethylene gas and carbon monoxide using specialized catalysts.This innovation incorporates two features to make the new-type plastics superior:the ability to degrade under ultraviolet light,and the new hydrophilic surface induced by introduction of new functional groups.The study was published in National Science Review(doi:10.1093/nsr/nwad039).

3'-Deoxyadenosin alleviates methamphetamine-induced aberrant synaptic plasticity and seeking behavior by inhibiting the NLRP3 inflammasome

Methamphetamine addiction is a brain disorder characterized by persistent drug-seeking behavior, which has been linked with aberrant synaptic plasticity. An increasing body of evidence suggests that aberrant synaptic plasticity is associated with the activation of the NOD-like receptor family pyrin domain containing-3(NLRP3) inflammasome. 3′-Deoxyadenosin, an active component of the Chinese fungus Cordyceps militaris, has strong anti-inflammatory effects. However, whether 3′-deoxyadenosin attenuates methamphetamine-induced aberrant synaptic plasticity via an NLRP3-mediated inflammatory mechanism remains unclear. We first observed that 3′-deoxyadenosin attenuated conditioned place preference scores in methamphetamine-treated mice and decreased the expression of c-fos in hippocampal neurons. Furthermore, we found that 3′-deoxyadenosin reduced the aberrant potentiation of glutamatergic transmission and restored the methamphetamine-induced impairment of synaptic plasticity. We also found that 3′-deoxyadenosin decreased the expression of NLRP3 and neuronal injury. Importantly, a direct NLRP3 deficiency reduced methamphetamine-induced seeking behavior, attenuated the impaired synaptic plasticity, and prevented neuronal damage. Finally, NLRP3 activation reversed the effect of 3′-deoxyadenosin on behavior and synaptic plasticity, suggesting that the anti-neuroinflammatory mechanism of 3′-deoxyadenosin on aberrant synaptic plasticity reduces methamphetamine-induced seeking behavior. Taken together, 3′-deoxyadenosin alleviates methamphetamine-induced aberrant synaptic plasticity and seeking behavior by inhibiting the NLRP3 inflammasome.

Recent Advance in Synaptic Plasticity Modulation Techniques for Neuromorphic Applications

Manipulating the expression of synaptic plasticity of neuromorphic devices provides fascinating opportunities to develop hardware platforms for artifi-cial intelligence.However,great efforts have been devoted to exploring biomimetic mechanisms of plasticity simulation in the last few years.Recent progress in various plasticity modulation techniques has pushed the research of synaptic electronics from static plasticity simulation to dynamic plasticity modulation,improving the accuracy of neuromorphic computing and providing strategies for implementing neuromorphic sensing functions.Herein,several fascinating strategies for synap-tic plasticity modulation through chemical techniques,device structure design,and physical signal sensing are reviewed.For chemical techniques,the underly-ing mechanisms for the modification of functional materials were clarified and its effect on the expression of synaptic plasticity was also highlighted.Based on device structure design,the reconfigurable operation of neuromorphic devices was well demonstrated to achieve programmable neuromorphic functions.Besides,integrating the sensory units with neuromorphic processing circuits paved a new way to achieve human-like intelligent perception under the modulation of physical signals such as light,strain,and temperature.Finally,considering that the relevant technology is still in the basic exploration stage,some prospects or development suggestions are put forward to promote the development of neuromorphic devices.

Mitochondrial recruitment in myelin:an anchor for myelin dynamics and plasticity?

Optimal propagation of neuronal electrical impulses depends on the insulation of axons by myelin,produced in the central nervous system by oligodendrocytes.Myelin is an extension of the oligodendrocyte plasma membrane,which wraps around an axon to form a compact multi-layered sheath.Myelin is composed of a substantially higher proportion of lipids compared to other biological membranes and enriched in a small number of specialized proteins.

Glial progenitor heterogeneity and plasticity in the adult spinal cord

Glial progenitor cells were reported to have the capacity to generate various types of cells in both the central nervous system(CNS)and peripheral nervous system.Glial progenitor cells can respond to diverse environmental signals and transform into distinct populations,each serving specific functions.Notably,the adult spinal cord hosts various populations of glial progenitors,a region integral to the central nervous system.During development,glial progenitors express glial fibrillary acidic protein(GFAP;Dimou and Gotz,2014).However,the specific identities of GFAP-expressing progenitors in the adult spinal cord were not thoroughly investigated.

Perspectives in human brain plasticity sparked by glioma invasion:from intraoperative(re)mappings to neural reconfigurations

Exploring the aptitude of the human brain to compensate functional consequences of a lesion damaging its structural architecture is a key challenge to improve patient care in various neurological diseases,to optimize neuroscientifically-informed strategies of postlesional rehabilitation,and ultimately to develop innovative neuro-regenerative therapies.The term‘plasticity’,initially referring to the intrinsic propensity of neurons to modulate their synaptic transmission in a learning situation,was progressively transposed to brain injury research and clinical neurosciences.Indeed,in the event of brain damage,adaptive mechanisms of compensation allow a partial reshaping of the structure and activities of the central nervous system,thus permitting to some extent the maintenance of brain functions.

From mice to humans:a need for comparable results in mammalian neuroplasticity

Brain plasticity-A universal tool with many variations:The study of brain plasticity has been gaining interest since almost a century and has now reached a huge amount of information(>80,000 results in PubMed).Overall,different types of plasticity,including stem cell-driven genesis of new neurons(adult neurogenesis),cells in arrested maturation(dormant neurons),neuro-glial and synaptic plasticity,can coexist and contribute to grant plastic changes in the brain,from a cellular to system level(Benedetti and Couillard-Despres,2022;Bonfanti et al.,2023).

Contribution of mechanical forces to structural synaptic plasticity:insights from 3D cellular motility mechanisms

Cells,tissues,and organs are constantly subjected to the action of mechanical forces from the extracellular environment-and the nervous system is no exception.Cell-intrinsic properties such as membrane lipid composition,abundance of mechanosensors,and cytoskeletal dynamics make cells more or less likely to sense these forces.Intrinsic and extrinsic cues are integrated by cells and this combined information determines the rate and dynamics of membrane protrusion growth or retraction(Yamada and Sixt,2019).Cell protrusions are extensions of the plasma membrane that play crucial roles in diverse contexts such as cell migration and neuronal synapse formation.In the nervous system,neurons are highly dynamic cells that can change the size and number of their pre-and postsynaptic elements(called synaptic boutons and dendritic spines,respectively),in response to changes in the levels of synaptic activity through a process called plasticity.Synaptic plasticity is a hallmark of the nervous system and is present throughout our lives,being required for functions like memory formation or the learning of new motor skills(Minegishi et al.,2023;Pillai and Franze,2024).

Photocatalytic Degradation of Plastic Waste: Recent Progress and Future Perspectives

Microplastics are persistent anthropogenic pollutants that have become a global concern due to their widespread distribution and unfamiliar threat to the environment and living organisms. Conventional technologies are unable to fully decompose and mineralize plastic waste. Therefore, there is a need to develop an environmentally friendly, innovative and sustainable photocatalytic process that can destroy these wastes with much less energy and chemical consumption. In photocatalysis, various nanomaterials based on wide energy band gap semiconductors such as TiO2 and ZnO are used for the conversion of plastic contaminants into environmentally friendly compounds. In this work, the removal of plastic fragments by photocatalytic reactions using newly developed photocatalytic composites and the mechanism of photocatalytic degradation of microplastics are systematically investigated. In these degradation processes, sunlight or an artificial light source is used to activate the photocatalyst in the presence of oxygen.