Study on phase retardation characteristic of LCVR using dispersion analysis and SVM

To calibrate the phase retardance of a Liquid crystal variable retarder(LCVR),its birefringence dispersion characteristic was analyzed,and the Support vector machines(SVM) algorithm was adopted to establish the prediction model.The obtained SVM decision function was used as a part of LCVR phase retardance,which was generated by the driving voltage.The experimental verification was carried out with a 568 nm laser.The results show that the deviation of the experimental value and the theoretical value is about 0.0061λ.SVM method could be used as an effective method for LCVR phase retardance characteristic calibration.

UTILIZING PHASE RETARD INTEGRATION METHOD OF FLOW BIREFRINGENCE TO ANALYSE THE FLOW WITH SYMMETRIC PLANE

The formulas which are suitable to birefringent medium with symmetric plane are derived by means of phase retard integration.We have adopted this concept to the axisymmetric problems and deduced some useful formulas for these cases.As a practical application,the strain rate analysis of flow in a diverging or a converging vessel is illustrated at the end of this paper.

Ellipsometric configurations using a phase retarder and a rotating polarizer and analyzer at any speed ratio

In this paper, we propose an ellipsometer using a phase retarder and rotating polarizer and analyzer at a speed ratio I：N. Different ellipsometric configurations are presented by assuming N = 1, 2, and 3. Moreover, two values of the offset angle of the retarder are considered for each ellipsometric configuration. The Mueller formalism is employed to extract the Stokes parameters, from which the intensity received by the detector is obtained. The optical properties of c-Si are calculated using all configurations. A comparison between different configurations is carried out considering the effect of the noise on the results and the uncertainties in the ellipsometric parameters as functions of the uncertainties of the Fourier coefficients. It is found that the alignment of the phase retarder has a crucial impact on the results and the ellipsometric configuration with speed ratio 1：1 is preferred over the other configurations.

Plasmon-induced absorption in stacked metamaterials based on phase retardation

In this paper, based on the constructive interference of plasmonic dipolar and quadrupolar modes, a classical analogue of electromagnetically induced absorption （EIA） is demonstrated theoretically in a stacked metamaterial consisting of a short metal strip （which acts as a bright resonator） and a long metal strip （acting as a dark resonator）, which has been reported to support the electromagnetically induced transparency （EIT） effect. The transition from EIA to EIT can be clearly observed in the absorbance spectra via varying the vertical spacing between two resonant oscillators. With the help of the coupled two-oscillator model, the phase shift between the bright and dark resonance modes is calculated by fitting the simulated absorbance spectra, which reveals the physical mechanisms behind constructive and destructive interference effects in EIT/EIA metamaterials.

Design of broad angular phase retarders for the complete polarization analysis of extreme ultraviolet radiation

A method of designing broad angular phase retarders in the extreme ultraviolet （EUV） region is presented. The design is based on a standard Levenberg-Marquardt algorithm combined with a common merit function. Using this method, a series of broad angular EUV phase retarders were designed using aperiodic Mo/Si multilayers. At photon energy of 90 eV, broad angular phase retarders with 30°, 60°, and 90° phase retardations have been realized in the angular range of 39°-51°. By analyzing and comparing the performances of the designed broad angular phase retarders, we found that the Mo/Si multilayer with more layers could obtain higher phase retardation in broader angular range when used to design the broad angular phase retarder. Broad angular phase retarders possess lower sensitivity toward changing incident angle compared with the traditional phase retarders designed with transmission periodic multilayers, and can be used for the polarization control of broad angular EUV sources.

Broadband achromatic phase retarder based on metal-multilayer dielectric grating

A new achromatic phase retarder based on a metal-multilayer dielectric grating structure is designed using the rigorous coupled wave analysis method and the genetic algorithm.The optimized phase retarder can maintain phase retardation around 90°from 900 nm to 1200 nm,and the maximum deviation is less than 4.5%while the diffraction efficiencies of TE and TM waves are both higher than 95%.Numerical analysis shows the designed phase retarder has a high fabrication tolerance of groove depth,duty cycle and incident angle.This achromatic phase retarder is simple in design and stable in performance,and can be widely used in optical systems.

Flame retardancy and its mechanism of polymers flame retarded by DBDPE/Sb_2O_3

The flammability characterization and thermal composition of polymers flame retarded by decabromodiphenylethane (DBDPE) and antimony trioxide (Sb2O3) were studied by cone calorimeter and thermogravimetry (TG). The results show that ABS/DBDPE/Sb2O3 has the similar flammability parameters and thermal composition curves to ABS/DBDPO/Sb2O3. It suggests that DBDPE/Sb2O3 has the similar flame retardant behavior to DBDPO/Sb2O3. The heat release rate (HRR) and the effect heat combustion (EHC) curves of polymers flame retarded by DBDPE/Sb2O3 all decrease, but the mass loss rate (MLR) curve slightly increase. It shows that the decrease of HRR is not due to the increase of char formation ratio but the generation of incombustible gases. The major flame retardant mechanism of DBDPE/Sb2O3 is gas phase flame retardant mechanism. Increasing content of Sb2O3 in DBDPE/Sb2O3 can improve the flame retardant property and thermal stability of acrylonitrile butadiene styrene. Sb2O3 has a good synergistic effect with DBDPE.

Methods for optical phase retardation measurement:A review

Optical-phase-retardation elements are widely used in many fields.Accurate measurement of their phase retardation is crucial to the practical effect of the element's processing and application.The development and present situation of the methods for optical phase retardation measurement are reviewed,with the wave plate,the most typical phase-retardation element,as an example.The latest research progress in this field is introduced;the principles and characteristics of individual measurement method are summarized and discussed.Three new methods based on laser frequency splitting or laser feedback are presented in detail,in which the laser is not only regarded as a light source but also plays a role of sensor.Moreover,no standard wave plates are needed and arbitrary phase retardation can be measured.Traceability,high precision and high repeatability are achieved as well.

Thermogravimetric Studies of Deposited Potash Impregnated for Flame-Retardancy into a Cotton Fabric

The effect of potash as a nondurable finish on the flammability of 100% cotton fabric （plain 180 g/m^2） was investigated. The bone-drled weighed fabrics were dipped into suitable concentrations of potash, with a volume of 100 mL at 20-2℃. The impregnation was followed by means of squeeze rolls and drying at 110 ℃. The samples were then reweighed with analytical precision. After conditioning overnight by using our ＂vertical flame tester＂ the optimum add-on values to impart flame-retardancy to cotton fabric was determined and expressed by 0.80 g of potash per 100 g fabric to be an efficient addition. Thermogravimetric analysis of pure cotton, treated cotton with potash at its optimum efficiency for donation of flame-retardancy into cotton fabric was fulfilled and the thermograms were compared and commented. The effectiveness of this hydroxide was attributed to the heat dissipation by the remaining consumed material during the combustion. The results obtained are in favor of ＂Dust or Wall Effect Theory＂.