Analysis of Light Load Efficiency Characteristics of a Dual Active Bridge Converter Using Wide Band-Gap Devices

In this paper, the zero voltage switching (ZVS) region of a dual active bridge (DAB) converter with wide band-gap (WBG) power semiconductor device is analyzed. The ZVS region of a DAB converter varies depending on output power and voltage ratio. The DAB converters operate with hard switching at light loads, it is difficult to achieve high efficiency. Fortunately, WBG power semiconductor devices have excellent hard switching characteristics and can increase efficiency compared to silicon (Si) devices. In particular, WBG devices can achieve ZVS at low load currents due to their low parasitic output capacitance (Co,tr) characteristics. Therefore, in this paper, the ZVS operating resion is analyzed based on the characteristics of Si, silicon carbide (SiC) and gallium nitride (GaN). Power semiconductor devices. WBG devices with low Co,tr operate at ZVS at lower load currents compared to Si devices. To verify this, experiments are conducted and the results are analyzed using a 3 kW DAB converter. For Si devices, ZVS is achieved above 1.4 kW. For WBG devices, ZVS is achieved at 700 W. Due to the ZVS conditions depending on the switching device, the DAB converter using Si devices achieves a power conversion efficiency of 91% at 1.1 kW output. On the other hand, in the case of WBG devices, power conversion efficiency of more than 98% is achieved under 11 kW conditions. In conclusion, it is confirmed that the WBG device operates in ZVS at a lower load compared to the Si device, which is advantageous in increasing light load efficiency.

SOFT SWITCHED SYNCHRONOUS RECTIFIER WITH PHASE-SHIFTED FULL BRIDGE CONVERTER AND ITS SMALL-SIGNAL ANALYSIS

By using the output inductors and body capacitances without adding any component compared with hard switching synchronous rectifier,the topology of a soft switched synchronous rectifier with phase-shifted full bridge zero voltage switching DC/DC converter is proposed. The converter efficiency is maximized due to soft switching of the full bridge MOSFETs and the synchronous MOSFETs, and also the low conduction loss of synchronous MOSFET. The operation principles of the circuit are analyzed in detail and the small-signal model is derived, also the converter dynamic characteristics are analyzed. Frequency responses of transfer functions under different values of transformer primary leakage inductance are discussed. The experimental results were obtained from a 400 V input and 100 A/12 V output DC/DC converter operating at 100 kHz. The results show that the converter efficiency is 2% higher in rated power than traditional diode rectifier.

Modeling and Current Programmed Control of a Bidirectional Full Bridge DC-DC Converter

Modelling of bidirectional full bridge DC-DC converter as one of the most applicable converters has received significant attention. Mathematical modelling reduces the simulation time in comparison with detailed circuit response;moreover it is convenient for controller design purpose. Due to simple and effective methodology, average state space is the most common method among the modelling methods. In this paper a bidirectional full bridge converter is modelled by average state space and for each mode of operations a controller is designed. Attained mathematical model results are in a close agreement with detailed circuit simulation.

Impedance Modeling and Stability Analysis of Dual Active Bridge Converter with LC Input Filter

The dual active bridge(DAB)converter is gaining more and more attention in various applications such as energy storage systems,electric vehicles and smart grids.To improve the quality of the input current,a LC filter is often cascaded at the input side of the DAB converter.However,there are instable problems of this cascaded system due to the impedance interactions of the DAB converter and the LC filter,although the DAB converter is stable at the individual operation mode.To assess the stability of the cascaded system of the DAB converter and the LC filter,the impedance model of the DAB converter is firstly developed based on generalized state-space averaging method.The developed impedance model can be used to accurately predict the stability of the DAB converter with its LC input filter.Based on the stability analysis,the optimum filter parameter design guideline is determined.The impedance model and stability analysis are validated by the simulation and experimental results.

A Flux DC Bias Suppression Scheme of Single-stage Full-bridge PFC Converters Based on Dead Zone Adjustment

由于单级桥式功率因数校正（power factor correction,PFC）AC/DC变换技术电路的特点,导致高频变压器存在偏磁现象,影响了系统正常工作。传统方式通过增加变压器气隙或使用隔直电容来防止变压器出现偏磁,但是该类方案影响了系统性能,并增加了电路的复杂程度。结合有源钳位单级PFC变换器工作特点,提出一种基于死区调节的偏磁抑制策略,通过改变系统的开关时序,能够有效抑制偏磁,具有不增加主电路复杂程度、不影响系统性能、数字控制和模拟控制都能够实现等优点。在提出抑制策略的基础上,设计实现电路,给出死区设计方法及影响规律,最后进行实验研究。理论分析及实验结果表明,该策略能够在不影响系统性能的基础上,有效抑制单级桥式PFC变换器的高频变压器偏磁。

Improved Full Bridge Converter with Low Peak Voltage on Rectifier Diodes

To suppress peak voltage on rectifier diodes in a full bridge( FB) converter,the mechanism of peak voltage was analyzed and an improved FB converter was proposed. One reason for peak voltage is the resonance of the transformer's leakage inductance and the rectifier diodes' junction capacitances. The other reason is that the fast reverse recovery current of the rectifier diodes flows through the transformer's leakage inductance. An H bridge composed of four diodes,an auxiliary inductance, and a clamping winding were adopted in the proposed converter,and peak voltage was suppressed by varying the equivalent inductance, principally in different operating modes. Experimental results demonstrate that the peak voltage of rectifier diodes decreases by 43%,the auxiliary circuit does not lead to additional loss, and the rising rate, resonant frequency,and amplitude of the rectifier diodes' voltage decrease.Peak voltage and electromagnetic interference( EMI) of rectifier diodes are suppressed.

Design and performance of an EMI filter to reduce conducted EMI in an isolated full bridge buck converter power supply

EMI Filter Design and Performance for isolated full bridge buck converter is developed in this paper. In order to design a high performance EMI filter, many issues need to be considered beforehand. Some important issues including accurate model of converter components, parasitic elements, its effect on EMI noise and impedance mismatch are included in this paper. A numerical prediction of EMI/EMC has the potential to evaluate EMI performances at the design stage and before prototyping. It can also help reduce the post-prototype EMC cost by minimizing late redesign and modifications of a design implementation. Saber simulator is used to analyze the EMI noises and EMI filter’s performance. Conducted EMI noise measurement and EMI filter design of isolated full bridge buck converter has been achieved while successfully satisfying the FCC class B limits in the frequency range from 150 kHz to 30 MHz. Simulation results are compared with experimental data and the effectiveness of the EMI simulation approach is demonstrated.

Application research on ZVZCS full-bridge converter technique

Based on ZVZCS （zero voltage zero current switching） full bridge converter technique, a novel inverter welding power supply is designed, in which the secondary side of the transformer adopts passive clamping circuit to reduce voltage stress of rectifying components. This supply can realize power switches ZVS （zero voltage switching ） or ZCS （zero current switching） within a very wide range of load; Only through setting up blocking capacitor in the primary side of transformer, the power transformer＇s bias in the full-bridge converter is suppressed and the primary current can be reset easily. In addition, how to calculate the blocking capacitor and its influence to power supply performance are also subjects discussed in this paper.

Fuzzy Logic Controlled Dual Active Bridge Series Resonant Converter for DC Smart Grid Application

Over the last few years, smart grids have become a topic of intensive research, development and deployment across the world. This is due to the fact that, through the smart grid, stable and reliable power systems can be achieved. This paper presents a fuzzy logic control for dual active bridge series resonant converters for DC smart grid application. The DC smart grid consists of wind turbine and photovoltaic generators, controllable and DC loads, and power converters. The proposed control method has been applied to the controllable load＇s and the grid side＇s dual active bridge series resonant converters for attaining control of the power system. It has been used for management of controllable load＇s state of charge, DC feeder＇s voltage stability during the loads and power variations from wind energy and photovoltaic generation and power flow management between the grid side and the DC smart grid. The effectiveness of the proposed DC smart grid operation has been verified by simulation results obtained by using MATLAB and PLECS cards.

The Implementation of a High Efficiency Full-Bridge Converter

A high efficiency full-bridge converter is investigated and implemented in this paper. The measured data result from the other converter implemented by IC UCC3895 is to compare with that of the previous converter. This full-bridge converter proposed and implemented converter can obtain about 96% power efficiency in conversion procedure when compared with that of 90%, which were ever published by the conventional techniques. Apart from, the L-C resonance circuits were developed and embedded into the popular PWM (pulse width modulation) power converter, which is referred as the soft-switching, so as to down sizing the volume of the IC which can totally reduces the power losses caused in the duration of a semi-con- ductor switching.

Research on Phase-Shifted Full-Bridge Circuit Based on Frequency and Phase-Shift Synthesis Modulation Strategy

The full-bridge converters usually use transformer leakage inductance and parallel resonant capacitors to achieve smooth current commutation and soft switching functions,which can easily cause problems such as energy leakage and significant duty cycle loss.This paper designs a novel full-bridge zero-current(FB-ZCS)converter with series resonant capacitors and proposes a frequency and phase-shift synthesis modulation(FPSSM)control strategy based on this topology.Compared with the traditional parallel resonant capacitor circuit,the passive components used are significantly reduced,the structure is simple,and there is only a slight energy loss.By controlling the charging time of the capacitor,it can be achieved without additional switches or auxiliary circuits.The automatic control of capacitor energy based on input current addresses the low efficiency of the traditional control strategies.This paper introduces its principle in detail and verifies it through simulation.Finally,an experimental prototype was built further to demonstrate the feasibility of the theory through experiments.The module can be applied to a photovoltaic DC collection system using input parallel output series(IPOS)cascade to provide a new topology for large-scale,long-distance DC transmission.

Novel forward mode AC/AC converters with high frequency link

A circuit configuration and a circuit topologic family of the novel forward mode AC/AC converters with high frequency link are presented. The circuit configuration is constituted of input cycloconverter, high frequency transformer, output cycloconverter, input and output filters. The circuit topologic family includes eight circuit topologies, such as full-bridge-full-wave mode, etc. The bi-polarity phase-shifted control strategy and steady principles are thoroughly investigated. The output characteristics are obtained. By using the bi-polarity phase-shifted control strategy with phase-shifted control between the output cycloconveter and the input cycloconverter, commutation overlap period of the output cycloconverter, and polarity selection of the output filtering inductance current and the input voltage, the leakage inductance energy and the output filtering inductance current are naturally commutated, and surge voltage and surge current of the cycloconverters are overcome. The converters have such advantages as simple topology, two-stage power conversions(LFAC/HFAC/LFAC), bi-directional power flow, high frequency electrical isolation, good output waveforms, and strong ability to stabilize voltage. The converters lay key technical foundation on a new-type of regulated sinusoidal AC power supplies and electronic transformers. The correction and advancement of the converters are well verified by a principle test.

ZERO-CURRENT AND ZERO-VOLTAGE SWITCHING PWM BOOST FULL-BRIDGE CON VERTER

This paper proposes a zer o current and zero voltage switching (ZCZVS) PWM Boost full bridge (FB) conve rter. With series inductors, the leading switches can realize zero current swit ching (ZCS) in a wide load range using the energy of the output capacitor. Ma king use of parasitic capacitors of the lagging switches and parallel auxiliary i nductance with the primary winding of the transformer, the lagging switches can realize zero voltage switching (ZVS) under any load. Compared with the ZCS PWM Boost FB converter, the new converter has no current duty cycle loss. Operat ional principle and parameter design are analyzed. Experimental results verify the effectiveness of the proposed converter.

Comparing the Quality of Power Generated from DFIG with Different Types of Rotor Converters

In this paper the quality of power generated from wind energy conversion system employing a double fed induction generator (DFIG) is investigated. The DFIG performance is tested with 3 types of converters interfacing the rotor with the grid. These are: the six-step thyristor inverter with diode rectifier, six-step IGBT inverter with diode rectifier, and 3-level IGBT-PWM inverter with diode rectifier. The harmonics in current and voltage, power factor value, and the transient behavior in each system are investigated and compared. Comparison is done at sub-and super-synchronous DFIG operational speed. In the system with lowest power quality passive filters or LC filter are added and improvement in system performance is recorded. From this study the optimum system from point of view of cost and control complexity is concluded.

Unified algorithm of single-phase active AC-DC converters and its applications

This paper discusses a novel boost single-phase active AC-DC converters, named low-end semi-controlled bridge AC-DC converter. By analysis, its topology and principle can be derived from the conventional single-phase power factor corrector （ PFC）. But it has also some differences, such as power device positions, inductor type, input voltage waveform detection and induction current detection, so its design is also different. The converter is implemented by employing two current detection approaches, i.e., current transformer detection and shunt resistor detection. Consequently, it can provide a steady DC output voltage with a low voltage ripple, approximately unitary input power factor and 2.5 kW output power. The experimental results show validity of the theoretical analysis.

A Qualitative Assessment of a Modified Multilevel Converter Topology M2LeC for Lightweight Low-Cost Electric Propulsion

A Cascade H Bridge (CHB) is evaluated for both electric vehicle motor traction control and off-vehicle charging against the Power ElectronicsUK Automotive Challenge for cost and mass for the year 2035. By combining the power electronics with batteries using low-voltage MOSFET transistors in a series cascade arrangement the cost and mass targets could be met 12 years earlier (in 2023 and 20 times lighter if an application specific integrated circuit (ASIC) is used. A 200 kW peak reference car was used to evaluate cost and mass benefits using four different topologies of power electronics. Vehicle installation is shown to be simplified as only passive cooling is required removing the need for liquid cooling systems and the arrangement is inherently safe;no high voltages are present when the vehicle is stationary. The inherently higher efficiency of CHB increases vehicle range. The converter with integrated batteries can also behave as an integrated on-board battery charger delivering additional off-vehicle benefits by removing the need for costly external chargers.

基于回流功率优化的直流微网DC-DC变流器超螺旋滑模控制

针对直流微网系统中双有源桥直流变换器在系统发生扰动时动态特性差及在单移相调制下变换器效率不高等问题,该文在扩展移相调制下提出一种结合回流功率优化的超螺旋滑模控制策略。首先,分析双有源全桥(dual-active-bridge,DAB)变换器在扩展移相调制下两种模式的传输功率、回流功率数学模型及软开关特性,并以传输功率数学模型为基础建立DAB变换器的降阶模型。其次,以回流功率作为目标函数,以传输功率和软开关特性作为约束条件,通过Karush-Kuhn-Tucker(KKT)条件法寻找最优移相比组合;利用DAB变换器降阶模型设计超螺旋滑模控制中的等效部分,采用超螺旋算法作为切换部分,这两部分与内移相比D1共同作用生成外移相比D2,用于调节变换器的输出电压。最后进行了仿真及实验验证,实验结果表明:在负载投切、输入电压突变、参考电压改变时变换器具有良好的动态性能,同时能有效地减小回流功率。

两桥臂交叉解耦不平衡控制策略研究

由于非不平衡控制策略中没有考虑线电压和相电流的相角差,造成三相电网的有功、无功电流无法完全补偿。为了解决这一问题,根据电压电流相角差,推导出单相补偿器中无功参考补偿电流与负载电流的关系,提出一种两桥臂交叉解耦不平衡控制策略,利用多变量滤波器和交叉解耦双复系数滤波器优化锁相环,精确锁定三相不平衡电网的电压频率和相位,对2个单相背靠背变换器的无功电流分别控制,进而利用两桥臂变换器补偿三相不平衡无功。实验结果验证了所提两桥臂交叉解耦不平衡控制策略,可抑制三相有功不平衡及补偿三相不平衡无功,将三相电流的不平衡度从150.0%降低至2.6%,三相电网功率因数从0.257提升至0.997,减少了三相无功补偿器的开关管个数。