Preparation and properties of RE^(3+) doped luminescent co-polymer by solution copolymerization

Bonded type RE3+ doped luminescent co-polymer was synthesized by solution free radical copolymerization. The influence of charge sequence, monomers and co-polymerized method on properties and structures of the co-polymers was studied. The emission intensity of the co-polymers at different RE3+ concentrations was tested. The results showed that the co-polymers of Eu-PSt and Eu-PMMA both had wide absorption peak at 200-400 nm and the strongest peak appeared at 235 nm. The fluorescent intensity of Eu3+ doped polystyrene co-polymer was stronger than that of Eu3+ doped PMMA copolymer. The characteristic emission of europium ions was observed in the co-polymers. The copolymer doped with rare earth elements showed the 'sensitization effect' for the central ions. The bonded-type rare earth copolymer not only enhanced the energy transfer efficiency, but also improved the fluorescence intensity by increasing the rigidity of main and side chain.

Open tubular capillary electrochromatography with block co-polymer coating for separation of β-lactam antibiotics

A new open-tubular capillary electrochromatography (OT-CEC) method for analysis of β-lactam antibiotics has been developed with unique block co-polymer coating. To obtain the highly ordered block polymer chains, reversible addition fragmentation chain transfer radical polymerization method was used to synthesize poly (maleic anhydride-styrene-N-isopropylacrylamide). The prepared block copolymer coating was characterized with NMR, fourier transform infrared spectroscopy and scanning electron microscope. Several key separation factors of OT-CEC, which including polymer amount,stability of the coating, temperature, species of organic additives, buffer pH and concentration, were investigated in detail. Our results indicated that the separation efficiency was improved greatly with the coating capillary and the three test analytes could be baseline separated. Then, the separation mechanism was briefly explored. Moreover, the proposed OT-CEC method displayed promising quantitative analysis property of the three test analytes with good linearity (R2>0.99), repeatability (relative standard deviations <0.9%) and high recovery (95.4%-106.2%). Further, the assay was applied in monitoring the three test β-lactam antibiotics (cephradine, cephalexin and amoxicillin) in serum samples, providing a useful platform for construction of novel polymer coatings in OT-CEC system and for analysis of drugs in real bio-samples.

Structural and functional evidence for two separate oligosaccharide binding sites of Pasteurella multocida hyaluronan synthase

Pasteurella multocida hyaluronan synthase (PmHAS) is a bi-functional glycosyltransferase, containing a β1,3-glucuronyltransferase and β1,4-N-acetylglucosaminetransferase domain. PmHAS catalyzes the elongation of hyaluronan (HA) through the sequential addition of single monosaccharides to the non-reducing end of the hyaluronan chain. Research is focused on the relation between the length of the HA oligosaccharide and the single-step elongation kinetics from HA4 up to HA9. It was found that the turnover number kcat increased with length to maximum values of 11 and 14 s-1 for NAc- and UA-transfer, respectively. Interestingly, the specificity constant kcat/KM increased with polymer length from HA5 to HA7 to a value of 44 mM-1s-1, indicating an oligosaccharide binding site with increasing specificity towards a heptasaccharide at the UA domain. The value of kcat/KM remained moderately constant around 8 mM-1s-1 for HA4, HA6, and HA8, indicating a binding site with significantly lower binding specificity at the NAc domain than at the UA domain. These findings are further corroborated by a structural homology model of PmHAS, revealing two distinct sites for binding of oligosaccharides of different sizes, one in each transferase domain. Structural alignment studies between PmHAS and glycosyltransferases of the GT-A fold showed significant similarity in the binding of the UDP-sugars and the orientation of the acceptor substrate. These similarities in substrate orientation in the active site and in essential amino acid residues involved in substrate binding were utilized to localize the two HA oligosaccharide binding sites.

Effects of Hydrophobicity of Ethylene Oxide-Propylene Oxide Copolymers on Phase Diagrams of Aqueous Two-Phase Systems and Partition Behaviors of Cephalexin and 7-Aminodeacetoxicephalos-poranic Acid

A series of ethylene oxide (EO)-propylene oxide (PO) randomco-polymers (EOPO) were used to form aqueous two-phase systems (ATPS)with ammonium sulfate. Effects of EOPO's properties on the phaseseparation behaviors and on the partition of cephalexin and7-aminodesacetoxicephalosporanic acid (7-ADCA) in ATPS wereinvestigated. Both the molar mass and molar ratio of EO to PO of EOPOcould greatly influence partition behaviors of cephalexin and 7-ADCAas well as the binodal curve of ATPS.

Effect of GMA Polymer Compatibilizers on Highly Filled Composites of Low Density Polyethylene/Magnesium Hydroxide

Functional polymers such as polyethylene grafted glycidyl methacrylate （PE-g-GMA） and ethylene-methyl acrylate-glycidyl methacrylate terpolymer （E/MA/GMA） were used as compatibilizers in the preparation of highly filled composites of polyethylene/magnesium hydroxide（PE/MH）. Comparative studies were performed on the effect of magnesium hydroxide and stearic acid on the interface within polymer and magnesium hydroxide composites. The effect of polymeric compatibilizers on the properties of the composites was studied using tensile and impact tests, torque rheological analysis, differential scanning calorimetry and environmental scanning electron microscopy （ESEM）. The microstructure of highly filled PE/MH composites changed after the addition of functional polymers. The mechanical properties of the composite material increased after compatibilization. The compatibilization processes of PE-g-GMA and E/MA/GMA were different. The grafted polymer was more compatible with polyethylene, which led to a polar polymer phase. In contrast, the tercopolymer tended to adhere to the surface of MH particles.