PMIA树脂溶液中盐酸含量的测定

分别以乙酸钠-甲醇溶液、氢氧化钾-甲醇溶液为滴定剂,采用电位滴定法测定不同中和程度的聚间苯二甲酰间苯二胺(PMIA)树脂溶液中盐酸含量,并对2种测试方法的准确度和精密度进行比较。结果表明:采用2种测试方法测定中和程度分别为0、60%、95%、100%的PMIA树脂溶液中盐酸含量,2种测试方法的测定结果相近;采用F检验和t检验两种统计法验证了显著性水平为0.05、置信度为95%时2种测试方法的准确度和精密度均无显著差异,以氢氧化钾-甲醇溶液为滴定剂的测试方法的精密度更高;采用标准盐酸加入法,并以氢氧化钾-甲醇溶液为滴定剂测定不同中和程度的PMIA树脂溶液中盐酸回收率,平均回收率为96.5%~98.5%,验证了该方法的准确性;对于正常滴定过程中等当点不易识别的PMIA树脂溶液,可通过预加已知量的盐酸后再采用氢氧化钾-甲醇溶液滴定,从而确定溶液的酸碱性。

聚对苯二甲酰对苯二胺气凝胶纤维的制备与性能

气凝胶纤维具有良好的柔韧性,其织物在可穿戴保温隔热领域受到了人们高度的关注。聚对苯二甲酰对苯二胺(PPTA)具有优异的耐热性、耐化学品腐蚀等性能,是制备气凝胶纤维的理想材料。然而,目前利用PPTA纤维(对位芳纶)的纳米纤维分散液制备气凝胶纤维的过程复杂、耗时且成本高,因此本工作通过合成具有良好可加工性的PPTA溶液,利用湿法纺丝和冷冻干燥工艺制备PPTA气凝胶纤维,极大地简化了工艺流程。实验分析表明,通过改变PPTA溶液的浓度可以有效地控制气凝胶纤维的孔结构及机械强度。当PPTA溶液的质量分数为2%时,制得的气凝胶纤维的孔隙率高达94.5%,断裂强度可达7.8 MPa;除此之外,该气凝胶纤维还具有高的比表面积(291 m2/g)和低的热导率,其织物的热导率为29.65 mW/(m·K)。当PPTA溶液的质量分数为5%时,气凝胶纤维的断裂强度高达20.5 MPa。本工作中所制备的气凝胶纤维具有极高的孔隙率、超低的密度和热导率以及良好的力学性能,为新一代保温隔热纺织品的设计和制造开辟了新的途径。

PBO纤维表面改性处理的研究进展

聚对苯撑苯并二噁唑(PBO)纤维因其比强度高、比模量高、耐热性好、阻燃性好以及优异的介电性能,现已在安全防护、建筑汽车等领域得到广泛应用。由于PBO纤维表面光滑、化学惰性,导致其与基体树脂界面结合差,进一步影响复合材料的整体性能,这大大限制了PBO纤维优异综合性能的发挥,所以对PBO纤维表面进行改性处理显得尤为重要。介绍了近年来国内外针对PBO纤维不同表面改性方法及对应复合材料性能改善程度的研究进展,从PBO纤维改性方法的分类入手,阐述了各种方法的基本原理。通过对这些处理方法的比较,阐述了国内PBO纤维表面改性的研究进展,指出了国内外在PBO纤维表面改性处理上的差距,为未来的发展方向提供了参考。PBO纤维表面改性方法包括化学刻蚀法、等离子体处理、表面涂层法、化学接枝法、紫外刻蚀法、上浆剂处理等。各种改性技术各有利弊,在选择改性方法时,理应考虑达到工艺快捷有效、经济环保和无损纤维性能等指标。未来,在PBO纤维表面改性的处理方法领域,将逐步向绿色环保的上浆剂处理方向发展。

INFLUENCE OF TRACES OF WATER ON THE SYNTHESIS AND ELECTROLUMINESCENCE PROPERTIES OF POLY(2-METHOXY, 5- (2' -ETHYLHEXYL OXY)- 1, 4-PHENYLENE VINYLENE)

It was found that traces of water in the reaction medium would result in a great increase of gel and a decrease of Molecular weight of the poly(2-methoxy,5-(2'-ethylhexyloxy)-1,4-phenylene vinylene) during the polymerization, which ultimately led to inferior film qualities and device properties. The device (ITO/PEDOT/MEH-PPV/Ba/Al) with MEH-PPV prepared under dry conditions has an external quantum efficiency of above 2.0%.

TRANSFER HYDROGENATION OF KETONES BY PROPAN－2－OL OVER POLY（PHENYLENE OXIDE） ANCHORED RUTBENIUM CATALYST

Both aliphatic and aromatic ketones are efficiently transfer-hydrogenated by propan-2-ol under mild conditions in the presence of a catalytic amount of poly(2,6-dimethyl-1,4-Phenylene oxide) (PPO) anchored ruthenium complex and sodium hydroxide. An important feature of this polymer anchored catalyst is its stability in air.

NOVEL HYPERBRANCHED POLY(PHENYLENE OXIDE)S WITH PHENOLIC TERMINAL GROUPS: EFFECTS OF REACTION TIME AND CORE MOLECULES ON THE MOLECULAR WEIGHT AND POLYDISPERSITY

A novel hyperbranched poly（phenylene oxide） （HPPO） with phenolic terminal groups was prepared from 4-bromo-4＇,4＂-dihydroxytriphenylmethane as AB2 monomer in dimethylsulfoxide （DMSO） via a modified Ullmann reaction. The molecular weight and polydispersity （PD） of the resulting polymers increased with increasing reaction time. In the presence of core molecules （bisphenol A and 1,3,5-trihydroxybenzene）, which have the similar molecular backbones to the reactive monomer, the molecular weight could be controlled by varying the core-to-monomer ratio. Incorporation of a very small amount of core molecules could lead to a higher molecular weight as compared with that without the addition of core molecules. However, when the core content reached certain extent, the molecular weight would decrease with the further increase in the core content. A new similar behavior of control over the PD was also obtained. The resulting polymers were characterized by ^1H-NMR, ^13C-NMR, FT-IR, and GPC.

The Synthesis and Characterization of High Molecular Weight Poly(phenylene sulfide/ether)

Poly（phenylene sulfide/ether） （PPSE） was synthesized from 4,4＇-dihydroxydiphenyl sulfide and 4,4＇-dichlorodiphenyl sulfide in solution by nucleophilic substitution reaction. The resulting polymer was characterized by viscosity measurement, elemental analysis, FT-IR, ^1H NMR, X-ray diffraction and thermal analysis. The results showed that the viscosities of the resulting polymer were above 0.68 dL/g, and the linear chain structure of product was confirmed. PPSE had the same reflex indices as poly（p-phenylene sulfide）, an orthorhombic crystalline with unit cell a=0.853, b=0.562, c=1.026nm. The melting temperature, glass transition temperature and initial decomposition temperature were found to be 228℃, 85℃ and 325℃, respectively. The product was soluble in common organic solvents such as NMP, N, N＇-dimethylformamide, N, N＇-dimethylacetamide and 1,2-dichloroethane.

The Insulator-to-Conductor Transition in Sulphonated Poly(Phenylene Oxide)Polymer membranes:Percolation Theory Approach

In this paper the percolation theory is employed to study the insulator-to-conductortransition in sulphonated poly（phenylene oxide）（SPPO） polymer membranes.The membranes withdifferent sulphonation degree were prepared and infrared characterized.The transition thresholdwas calculated by the experimental data of membrane conductivities and the coordination numberwas thus estimated.The functional group-SO3H distribution in the membrane was evaluated inaccordance with the calculations and showed a non-random dispersion on the microscopic scale.

SYNTHESIS AND MORPHOLOGICAL STRUCTURE OF POLY (PHENYLENE SULFIDE AMIDE)

Poly(phenylene sulfide amide) (PPSA) has been synthesized by using sulfur as S source which reacts with dichlorobenzamide (DCBA) and alkali in polar organic solvent at the atmospheric pressure. The polymer structures were determined by elemental analysis, FT-IR and H-1-NMR. It is shown that the yielded polymer has linear structure and its structure unit is -p-C6H4-CONH -p-C6H4-S-. The polymer morphology was studied by X-ray diffraction and polarized microscopy. The results show that PPSA is a crystalline polymer and its spherulites are the aggregation of nontwisting lamella or micro-thread structure. Under shearing force, these crystals are dispersed to form micro-fibrillar structure. The decomposition kinetics of PPSA was also studied at different heating rates. The decomposition energy of PPSA is higher than that of PPS.

Hydration effect on the electronic transport properties of oligomeric phenylene ethynylene molecular junctions

A first-principles computational method based on the hybrid density functional theory is developed to simulate the electronic transport properties of oligomeric phenylene ethynylene molecular junctions with H2O molecules accumulated in the vicinity as recently reported by Na et al. [Nanotechnology 18 424001 （2007）]. The numerical results show that the hydrogen bonds between the oxygen atoms of the oligomeric phenylene ethynylene molecule and H2O molecules result in the localisation of the molecular orbitals and lead to the lower transition peaks. The H2O molecular chains accumulated in the vicinity of the molecular junction can not only change the electronic structure of the molecular junctions, but also open additional electronic transport pathways. The obvious influence of H2O molecules on the electronic structure of the molecular junction and its electronic transport properties is thus demonstrated.

GAS SORPTION AND TRANSPORT IN POLY (PHENYLENE OXIDE)(PPO)AND ARYL-BROMINATED PPO MEMBRANES

The apparent solubility (S), concentration-average diffusivity (D), and permeability (P), for C0_2, CH_4 and N_2 through PPO and aryl-brominated PPO at 35℃ for pressure ranging from 1 to 26 atm are reported. It is found that P, D, and S of the membranes to all the three gases vary with the extent of bromination. S increases with the increase of the percent of bromine in each case, but D to CO_2 increases remarkably only at higher degree of brominafion, and therefore, P to CO_2 is increased by more than 100% over a wide range ofpressure in the case. The solubility data are well described by the dual mode sorption model. It is found that the gas molecules sorbed by the Langmuir mode are relatively more immobilized and the contribution of the nonequilibrinm character of the polymer to gas permeation increases obviously for CO_2 and is hardly changed for CH_4 with increasing bromine content. These observations are interpreted in terms of changes in specific free volume (SFV)and the cohesive energy density (CED) of the polymers.

EFFECT OF SOLVENT COMPOSITION ON THE SULFONATION DEGREE OF POLY(PHENYLENE OXIDE) (PPO)

This paper investigates the possibility of attaining sulphonated poly(phenylene oxide) (SPPO) with a relativelyhigher sulfonation degree. To achieve this aim, the approach we adopt is to improve the solubility of the final product in themixed solvent so that the sulfonation may take place between the bulk solutions and PPO powders even at higher sulfonationdegree. It is shown that the addition of a proper amount of dimethyl formide (DMF) to the conventional PPO-chloroformsystem can actually enhance the sulfonation effect. The solvent composition is then correlated with the sulfonation degreebased on the solubility parameters. It is interesting to find that solubility parameters between the mixed solvent and theprecipitated products keep an approximately unchanged value at about 4.9, which is just equal to that when pure chloroformis used, though the solubility parameters of both solvents increase with the content of DMF in solution. This may be the mainreason why the addition of DMF can reduce the precipitation and improve the ion exchange capacity (IEC) of SPPOpolymer.

Poly(meta-phenylene) Derivative with Rigid Twisted Biphenyl Units in Backbone:Synthesis,Structural Characterization,Photophysical Properties and Electroluminescence

A soluble poly（meta-phenylene） derivative with rigid twisted biphenyl unit was synthesized by the Yamamoto coupling reaction. The polymer is soluble in common organic solvents, and the number-average molecular weight is about 6500. The UV-Vis and quantum chemical calculation indicate that the different conformation segments named ＂conformers＂ exist in the polymer backbones; it was also further confirmed by the single crystal X-ray diffraction study of the dimeric model compound. The π-π^＊ transition of biphenyl segments of twisted and planar conformations made the polymer exhibit a strong absorption around 256 nm and a weak absorption at about 300 nm. Furthermore, the polymer exhibits a strong UV photoluminescence at 372 nm when the excitation wavelengths are longer than 300 run. The ultraviolet-emitting electroluminescence（EL） device with the single layer structure shows EL λmax of the derivative at 370 nm.

Preparation of Poly (Phenylene Sulfide Amide) by Sulfur Solution Route

A new process for preparing poly(phenylene sulfide amide, PPSA), which is by reaction of sulfur instead of sodium sulfide as S source with dichlorobenzamide (DCBA) and alkali in polar organic solvent at the atmospheric pressure (called sulfur solution route), is reported in the present paper. The influences of polymerization time, molar ratio of precursors, catalyst and solvent upon the polymer were investigated. To seek the best parameters of polymerization, orthogonal design was employed in the experiments. The results indicate that the molar ratio of precursors is the most significant effect on both of viscosity and yield of the polymer. The suitable parameters for preparing the related polymer are presented. The polymer was characterized by IRspectrum, 1HNMRspectrum and Raman spectrum, etc.

STUDY OF THE REACTION BETWEEN α-KETOTHIOANILIDE AND PHENYLENE DIAMINE

When α-ketothioanilide reacts with o-phenylenediamine,there are two competing reactions.One is condensation which forms substituted quinoxaline and the other is substitution which forms substituted quinoxaline-2-thione·By controlling the reaction condition,we can obtain either quinoxaline or quinoxaline-2-thione as the main product.

Theoretical study of structural and electronic properties of oligo(thiophene-phenylene)s in comparison with oligothiophenes and oligophenylenes

在这个工作， oligo (thiophene 苯撑)(4TP ) 的结构、 opto 电子的性质上的量化学药品调查被执行。结果与相应 oligothiophene (8T ) 和 oligophenylene (8P ) 的性质比较被讨论。当这类进行的聚合物的 opto 电子的性质被他们的电子乐队差距管理，我们将也在人， LUMO 和这三材料的乐队差距精力之中介绍比较。

Thermal Stability Improvement and Structural Change of Oil Gels Formed by Styrene-Butadiene-Styrene Triblock Copolymer Induced by Adding Poly(phenylene ether)

The thermal stability of oil gels formed by styrene-butadiene-styrene triblock copolymer (SBS) was improved by adding a small amount of poly(phenylene ether) (PPE), which has a higher glass transition temperature (Tg). In naphthenic oil which is a good solvent for the butadiene blocks, but a non-solvent for the styrene blocks and PPE, PPE was selectively included into styrene blocks in SBS, and induced the increase of the Tg of these blocks. The melting temperature determined by viscoelastic measurements and softening temperature of the gels were elevated by adding PPE, while no significant change was detected by adding polystyrene. The gel became opaque by adding PPE, and partially separated phases were observed by field emission scanning electron microscopy (FE-SEM). The dependence of the viscoelastic behavior on the PPE concentration can be explained by the structural change observed by FE-SEM.

CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅰ.POLY(P-PHENYLENE TEREPHTHALATE)

The morphology and crytal structure of poly(p-phenylene terephthalate) (PPT), prepared by confined thin filmmelt (CTFMP) and solution (CTFSP) and bulk solution polymerization, were characterized by transmission electronmicroscopy, electron dimaction and molecular modeling. The unit cell is monoclinic (P2_1/a space group) with parameters a =7.89, b = 5.49, c = 12.65 A, α=γ= 90°, β=100.33°, density = 1.48 g/cm^3, the a, b and β values differing slightly from thosereported previously in the literature. A degree of variation in relative intensities of hk0 reflections in, apparently, untilted[001] ED patterns was observed from a given sample, suggesting some variation in molecular packing. ED evidence wasfound for a second phase, with [001] appearing the same as for phase Ⅱ of the related poly(p-oxybenzoate) (PpOBA)polymer. CTFMP crystals polymerized above 220℃ (up to 370℃) and CTFSP crystals polymerized at 300℃ consisted oflamellae 100-200 A thick.