Performance Assessment of a Real PV System Connected to a Low-Voltage Grid

The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Therefore,this paper assesses the performance of a 51 kW PV solar power plant connected to a low-voltage grid to feed an administrative building in the 6th of October City,Egypt.The performance analysis of the considered grid-connected PV system is carried out using power system simulator for Engineering(PSS/E)software.Where the PSS/E program,monitors and uses the power analyzer that displays the parameters and measures some parameters such as current,voltage,total power,power factor,frequency,and current and voltage harmonics,the used inverter from the type of grid inverter for the considered system.The results conclude that when the maximum solar radiation is reached,the maximum current can be obtained from the solar panels,thus obtaining the maximum power and power factor.Decreasing total voltage harmonic distortion,a current harmonic distortion within permissible limits using active harmonic distortion because this type is fast in processing up to 300 microseconds.The connection between solar stations and the national grid makes the system more efficient.

Analysis for Effects of Temperature Rise of PV Modules upon Driving Distance of Vehicle Integrated Photovoltaic Electric Vehicles

The development of vehicle integrated photovoltaics-powered electric vehicles (VIPV-EV) significantly reduces CO2 emissions from the transport sector to realize a decarbonized society. Although long-distance driving of VIPV-EV without electricity charging is expected in sunny regions, driving distance of VIPV-EV is affected by climate conditions such as solar irradiation and temperature rise of PV modules. In this paper, detailed analytical results for effects of climate conditions such as solar irradiation and temperature rise of PV modules upon driving distance of the VIPV-EV were presented by using test data for Toyota Prius and Nissan Van demonstration cars installed with high-efficiency InGaP/GaAs/InGaAs 3-junction solar cell modules with a module efficiency of more than 30%. The temperature rise of some PV modules studied in this study was shown to be expressed by some coefficients related to solar irradiation, wind speed and radiative cooling. The potential of VIPV-EV to be deployed in 10 major cities was also analyzed. Although sunshine cities such as Phoenix show the high reduction ratio of driving range with 17% due to temperature rise of VIPV modules, populous cities such as Tokyo show low reduction ratio of 9%. It was also shown in this paper that the difference between the driving distance of VIPV-EV driving in the morning and the afternoon is due to PV modules’ radiative cooling. In addition, the importance of heat dissipation of PV modules and the development of high-efficiency PV modules with better temperature coefficients was suggested in order to expand driving range of VIPV-EV. The effects of air-conditioner usage and partial shading in addition to the effects of temperature rise of VIPV modules were suggested as the other power losses of VIPV-EV.

Evaluation of Grid-Connected Photovoltaic Plants Based on Clustering Methods

Photovoltaic(PV)systems are electric power systems designed to sup-ply usable solar power by means of photovoltaics,which is the conversion of light into electricity using semiconducting materials.PV systems have gained much attention and are a very attractive energy resource nowadays.The substantial advantage of PV systems is the usage of the most abundant and free energy from the sun.PV systems play an important role in reducing feeder losses,improving voltage profiles and providing ancillary services to local loads.However,large PV grid-connected systems may have a destructive impact on the stability of the elec-tric grid.This is due to thefluctuations of the output AC power generated from the PV systems according to the variations in the solar energy levels.Thus,the elec-trical distribution system with high penetration of PV systems is subject to perfor-mance degradation and instabilities.For that,this project attempts to enhance the integration process of PV systems into electrical grids by analyzing the impact of installing grid-connected PV plants.To accomplish this,an indicative representa-tion of solar irradiation datasets is used for planning and powerflow studies of the electric network prior to PV systems installation.Those datasets contain lengthy historical observations of solar energy data,that requires extensive analysis and simulations.To overcome that the lengthy historical datasets are reduced and clus-tered while preserving the original data characteristics.The resultant clusters can be utilized in the planning stage and simulation studies.Accordingly,studies related to PV systems integration into the electric grid are conducted in an efficient manner,avoiding computing resources and processing times with easier and practical implementation.

Implementation of FPGA Based MPPT Techniques for Grid-Connected PV System

Global energy demand is growing rapidly owing to industrial growth and urbanization.Alternative energy sources are driven by limited reserves and rapid depletion of conventional energy sources(e.g.,fossil fuels).Solar photovol-taic(PV),as a source of electricity,has grown in popularity over the last few dec-ades because of their clean,noise-free,low-maintenance,and abundant availability of solar energy.There are two types of maximum power point track-ing(MPPT)techniques:classical and evolutionary algorithm-based techniques.Precise and less complex perturb and observe(P&O)and incremental conduc-tance(INC)approaches are extensively employed among classical techniques.This study used afield-programmable gate array(FPGA)-based hardware arrange-ment for a grid-connected photovoltaic(PV)system.The PV panels,MPPT con-trollers,and battery management systems are all components of the proposed system.In the developed hardware prototype,various modes of operation of the grid-connected PV system were examined using P&O and incremental con-ductance MPPT approaches.

基于PVsyst的光伏设计及阴影仿真

为了降低光伏电站的初始投资,以常州科教城为例,根据当地的气象、环境等因素,设计了一套并网光伏发电系统,对光伏组件倾角选择、组件串并联、逆变器选型、方阵最小间距等进行了优化设计。在组件布置过程中,对阴影遮挡现象进行了分析,运用PVsyst软件对设计方案进行模拟仿真。通过仿真结果提出了电站设计的可行性建议,对光伏电站的降本增效具有指导意义。

Synergetic optimization operation method for distribution network based on SOP and PV

The integration of distributed generation brings in new challenges for the operation of distribution networks,including out-of-limit voltage and power flow control.Soft open points(SOP)are new power electronic devices that can flexibly control active and reactive power flows.With the exception of active power output,photovoltaic(PV)devices can provide reactive power compensation through an inverter.Thus,a synergetic optimization operation method for SOP and PV in a distribution network is proposed.A synergetic optimization model was developed.The voltage deviation,network loss,and ratio of photovoltaic abandonment were selected as the objective functions.The PV model was improved by considering the three reactive power output modes of the PV inverter.Both the load fluctuation and loss of the SOP were considered.Three multi-objective optimization algorithms were used,and a compromise optimal solution was calculated.Case studies were conducted using an IEEE 33-node system.The simulation results indicated that the SOP and PVs complemented each other in terms of active power transmission and reactive power compensation.Synergetic optimization improves power control capability and flexibility,providing better power quality and PV consumption rate.

Electro-Optical Model of Soiling Effects on Photovoltaic Panels and Performance Implications

In this paper,a detailed model of a photovoltaic(PV)panel is used to study the accumulation of dust on solar panels.The presence of dust diminishes the incident light intensity penetrating the panel’s cover glass,as it increases the reflection of light by particles.This phenomenon,commonly known as the“soiling effect”,presents a significant challenge to PV systems on a global scale.Two basic models of the equivalent circuits of a solar cell can be found,namely the single-diode model and the two-diode models.The limitation of efficiency data in manufacturers’datasheets has encouraged us to develop an equivalent electrical model that is efficient under dust conditions,integrated with optical transmittance considerations to investigate the soiling effect.The proposed approach is based on the use of experimental current-voltage(I-V)characteristics with simulated data using MATLAB/Simulink.Our research outcomes underscores the feasibility of accurately quantifying the reduction in energy production resulting from soiling by assessing the optical transmittance of accumulated dust on the surface of PV glass.

Probabilistic Global Maximum Power Point Tracking Algorithm for Continuously Varying Partial Shading Conditions on Autonomous PV Systems

A photovoltaic (PV) string with multiple modules with bypass diodes frequently deployed on a variety of autonomous PV systems may present multiple power peaks under uneven shading. For optimal solar harvesting, there is a need for a control schema to force the PV string to operate at global maximum power point (GMPP). While a lot of tracking methods have been proposed in the literature, they are usually complex and do not fully take advantage of the available characteristics of the PV array. This work highlights how the voltage at operating point and the forward voltage of the bypass diode are considered to design a global maximum power point tracking (GMPPT) algorithm with a very limited global search phase called Fast GMPPT. This algorithm successfully tracks GMPP between 94% and 98% of the time under a theoretical evaluation. It is then compared against Perturb and Observe, Deterministic Particle Swarm Optimization, and Grey Wolf Optimization under a sequence of irradiance steps as well as a power-over-voltage characteristics profile that mimics the electrical characteristics of a PV string under varying partial shading conditions. Overall, the simulation with the sequence of irradiance steps shows that while Fast GMPPT does not have the best convergence time, it has an excellent convergence rate as well as causes the least amount of power loss during the global search phase. Experimental test under varying partial shading conditions shows that while the GMPPT proposal is simple and lightweight, it is very performant under a wide range of dynamically varying partial shading conditions and boasts the best energy efficiency (94.74%) out of the 4 tested algorithms.

Study on Image Recognition Algorithm for Residual Snow and Ice on Photovoltaic Modules

The accumulation of snow and ice on PV modules can have a detrimental impact on power generation,leading to reduced efficiency for prolonged periods.Thus,it becomes imperative to develop an intelligent system capable of accurately assessing the extent of snow and ice coverage on PV modules.To address this issue,the article proposes an innovative ice and snow recognition algorithm that effectively segments the ice and snow areas within the collected images.Furthermore,the algorithm incorporates an analysis of the morphological characteristics of ice and snow coverage on PV modules,allowing for the establishment of a residual ice and snow recognition process.This process utilizes both the external ellipse method and the pixel statistical method to refine the identification process.The effectiveness of the proposed algorithm is validated through extensive testing with isolated and continuous snow area pictures.The results demonstrate the algorithm’s accuracy and reliability in identifying and quantifying residual snow and ice on PV modules.In conclusion,this research presents a valuable method for accurately detecting and quantifying snow and ice coverage on PV modules.This breakthrough is of utmost significance for PV power plants,as it enables predictions of power generation efficiency and facilitates efficient PV maintenance during the challenging winter conditions characterized by snow and ice.By proactively managing snow and ice coverage,PV power plants can optimize energy production and minimize downtime,ensuring a sustainable and reliable renewable energy supply.

太阳能光伏光热PV/T组件在建筑设计中的应用

建筑领域“双碳”目标的提出,使得降低建筑能耗成为目前亟需解决的问题。可再生能源同建筑领域的有机结合被认为是解决建筑能耗的重要环节。通过对太阳能光伏光热技术的发展进行总结,研究太阳能光伏光热技术在建筑领域中的设计方法,提出了对未来光伏光热建筑一体化的设计思考,为以后太阳能光伏光热PV/T技术产业的发展提供参考。

Tilt Angle Optimality Criteria for Stand Alone PV Systems

The conventional approach to optimizing tilt angles for fixed solar panels aims to maximize energy generation over the entire year. However, in the context of a supply controlled electric grid, where solar energy availability varies, this criterion may not be optimal. This study explores two alternative optimization criteria focused on maximizing baseload supply potential and minimizing required storage capacity to address seasonality in energy generation. The optimal tilt angles determined for these criteria differed significantly from the standard approach. This research highlights additional factors crucial for designing solar power systems beyond gross energy generation, essential for the global transition towards a fully renewable energy-based electric grid in the future.

Soft-switching Grid-connected PV Inverter With Interleaved Flyback Topology

提出一种应用于单个光伏组件的软开关交错反激并网逆变器拓扑及其软开关控制策略。针对反激变压器漏感问题，提出漏感能量吸收回馈电路，实现了漏感能量吸收再利用，并实现了开关管漏源电压的钳位，提高了变换效率同时降低了开关管关断电压尖峰；提出基于数字处理器的反激变换器变开关频率谐振软开关控制策略，实现了开关管的零电压开通，同时改善了逆变器的电磁兼容特性；提出的交错并联反激逆变器有助于减小变压器和滤波器的体积，提高功率密度。详细分析变换器的工作原理，分析变开关频率谐振软开关控制方式的原理和实现条件，最后进行实验验证。

太阳能PV/T光储直驱热电联产系统性能

面对居民日益增长的生活热水和电能需求,光伏/光热(photovoltaic/thermal,PV/T)技术的应用可以降低建筑运行时的能源消耗。本文介绍了一种太阳能PV/T光储直驱热电联产(combined heat and power,CHP)系统,为了减少系统运行过程中的能量损失,采用直流压缩机和储能电池,并在兰州地区对系统的运行性能开展了实验测试。研究结果表明,PV/T系统的光伏板温度相比传统PV组件温度平均降低12.26℃,平均发电效率相对提升8.1%。在将24.4~27.2℃的水加热到50.1~50.7℃的过程中,平均性能系数(coefficient of performance,COP)可达到5.48,相比传统空气源热泵热水器提高82.1%~106.8%。平均集热效率和综合效率分别为37.30%和71.24%,PV/T系统的发电量和耗电量分别为3.33kWh和1.69kWh,发电量相比PV系统提高5.7%。太阳能PV/T光储直驱热电联产系统可以减少建筑部门的能源消耗,并提升PV/T系统的发电效率和综合效率,在晴天条件下可以实现离网运行。

H6 Non-isolated Full Bridge Grid-connected PV Inverters With Low Leakage Currents

为满足非隔离光伏并网发电系统对共模漏电流的限制，提出一种六开关逆变器拓朴（H6拓扑）。所提出的H6拓扑在功率传输模态时，进网电流半个工频周期流过3支开关管，而另半个工频周期流过2支开关管，故相对于H5拓扑，降低了通态损耗，有利于热应力均衡，且仍满足续流阶段光伏电池输出端与电网脱离的要求。详细分析拓扑的工作原理，并推论给出H6非隔离光伏并网逆变器的其它3种拓扑结构；比较分析了H5拓扑、Heric拓扑和H6拓扑的损耗和成本。通过1kW通用样机平台对比验证了上述3种拓扑的效率和共模特性。实验结果表明，H6拓扑的变换效率高于H5拓扑、但略低于Heric拓扑，共模特性优于Heric拓扑、但略劣于H5拓扑。

Optimal configuration strategy of energy storage system in high photovoltaic penetration micro-grid based on voltage sensitivity analysis

Energy storage is an effective measure to deal with internal power fluctuation of micro-grid and ensure stable operation, especially in the micro-grid with high photovoltaic(PV) penetration. Its capacity configuration is related to the steady, safety and economy of micro-grid.In order to improve the absorptive capacity of micro-grid on maximizing the use of distributed PV power in micro-grid, and improve the power quality, an optimal energy storage configuration strategy is proposed, which takes many factors into account, such as the topology of micro-grid, the change of irradiance, the load fluctuation and the cable. The strategy can optimize the energy storage allocation model to minimize the storage power capacity and optimize the node configuration.The key electrical nodes are identified by using the sensitivity coefficient of the voltage, and then the model is optimized to simplify calculation. Finally, an example of the European low-voltage micro-grid and a micro-grid system in the laboratory is used to verify the effectiveness of the proposed method.The results show that the proposed method can optimize the allocation of capacity and the node of the energy storage system.

Low Voltage Ride through Control Capability of a Large Grid Connected PV System Combining DC Chopper and Current Limiting Techniques

This paper presents the development and performance capability of a comprehensive Low voltage ride through (LVRT) control scheme that makes use of both the DC chopper and the current limiting based on the required reactive power during fault time. The study is conducted on an 8.5 MW single stage PV power plant (PVPP) connected to the Rwandan grid. In the event of fault disturbance, this control scheme helps to overcome the problems of excessive DC-link voltage by fast activation of the DC chopper operation. At the same instance, AC current is limited to the maximum rating of the inverter as a function of the injected reactive current. This helps overcome AC-over- current that may possibly lead to damage or disconnection of the inverter. The control scheme also ensures voltage support and power balance through the injection of reactive current as per grid code requirements. Selected simulations using MATLAB are carried out in the events of different kinds of fault caused voltage dips. Results demonstrate the effectiveness of the proposed LVRT control scheme.

Resiliency oriented control of a smart microgrid with photovoltaic modules

The resiliency of a standalone microgrid is of considerable issue because the available regulation measures and capabilities are limited.Given this background,this paper presented a new mathematical model for a detailed photovoltaic(PV)module and the application of new control techniques for efficient energy extraction.The PV module employs a single-stage conversion method to integrate it with the utility grid.For extraction the maximum power from PV and integrate it to power grid,a three-phase voltage source converter is used.For obtaining the maximum power at a particular irradiance a maximum power point tracking(MPPT)scheme is used.The fuzzy logic control and adaptive network-based fuzzy inference system are proposed for direct current(DC)link voltage control.The proposed model and control scheme are validated through a comparison with the standard power-voltage and current-voltage charts for a PV module.Simulation results demonstrate that the system stability can be maintained with the power grid and in the island mode,in contrast with the MPPT.

PV-Grid Tie System Energizing Water Pump

This paper presents the behaviours of three-phase induction motor driving centrifugal pump under various solar irradiation levels, where the motor speed and torque depend on the source voltage and frequency, while the water-flow rate depends on the motor speed, density, and static head according to affinity flow. Matlab/Simulink model is proposed for studying the behaviours of these machines with respect to water flow capacity, motor current, electro-magnetic torque, and motor efficiency. The proposed photovoltaic with maximum power point tracking model based on observation and perturbation (O&P) maximum power tracking model is applied. The output voltage is regulated throughout Buck-Boost converter with purpose maintaining the output voltage at predetermined values. Since Induction motors are widely used in pump systems, the electromagnetic torque, water-flow rate are studied for various source frequencies. Comparison analysis is conducted for both motors with respect to water flow-rate, heads elevation, and motor current. In addition to that, the proposed system presents Photovoltaic-Grid (PV-Grid) Integrated model, where the power shortage required for normally operation of the pump is drawn from the electrical grid.

Research and practice of designing hydro/ photovoltaic hybrid power system in microgrid

Small-hydro power station is often used in remote areas beside a river,but it doesn't match electricity demand so well,especially in dry seasons. A photovoltaic (PV) system with battery is a suitable option to complement the electricity gap. In this paper,a new structure of megawatt-class PV system integrating battery at DC-bus (DC: direct current) is proposed to be used in hydro/PV hybrid power system,and 4 main designing considerations and several key equipments are discussed. In 2011,a 2 MWp PV station with the proposed structure was built up in Yushu,China. From stability analysis,the station shows a strong stability under load cut-in/off and solar irradiance's fluctuation.

基于PVsyst的光伏系统研究

基于PVsyst软件,以吐鲁番地区某民居为模拟对象,对当地的气象数据进行分析,并构建了一套安装在屋顶的光伏并网发电系统。对光伏并网系统的安装倾角进行优化,并对光伏组件进行选型,对系统损失进行分析。最后根据模拟结果,对影响系统发电效率的因素进行分析并提出了一些优化方案,以及得出吐鲁番地区19.1 kW的光伏并网系统全年发电量为27.9 MW·h,系统效率为80.9%,能量回收期为2.98年,每年可减少32790 kg的CO_(2)排放量,具有一定的环境效益;若按新疆光伏上网电价0.262元(/kW·h)进行计算,每年还可带来7309.8元的收入。该研究对实际光伏并网系统的设计施工具有一定的参考意义。