At-rest lateral earth pressure of compacted expansive soils:Experimental investigations and prediction approach

This paper presents experimental studies on a compacted expansive soil,from Nanyang,China for investigating the at-rest lateral earth pressureσL of expansive soils.The key studies include(i)relationships between theσL and the vertical stressσV during soaking and consolidation,(ii)the influences of initial dry densityρd0 and moisture content w 0 on the vertical and lateral swelling pressures at no swelling strain(i.e.σV0 andσL0),and(iii)evolution of theσL during five long-term wetting-drying cycles.Experimental results demonstrated that the post-soakingσL-σV relationships are piecewise linear and their slopes in the passive state(σL>σV)and active state(σL<σV)are similar to that of the consolidationσL-σV relationships in the normal-and over-consolidated states,respectively.The soakingσL-σV relationships converge to the consolidationσL-σV relationships at a thresholdσV where the interparticle swelling is restrained.TheσL0 andσV0 increase monotonically withρd0;however,they show increasing-then-decreasing trends with the w 0.The extent of compaction-induced swelling anisotropy,which is evaluated byσL0/σV0,reduces with an increase in the compaction energy and molding water content.TheσL reduces over moisture cycles and the stress relaxation in theσL during soaking is observed.An approach was developed to predict the at-rest soakingσL-σV relationships,which requires conventional consolidation and shear strength properties and one measurement of theσL-σV relationships during soaking.The proposed approach was validated using the results of three different expansive soils available in the literature.

Swelling pressure evolution characterization of strong expansive soil considering the influence of reserved expansion deformation

Numerous engineering cases have demonstrated that the expansive soil channel slope remains susceptible to damage with the implementation of a rigid or closed protective structure. It is common for the protective structure to experience bulging failure due to excessive swelling pressure. To investigate the swelling pressure properties of expansive soil, the constant volume test was employed to study the influence of water content and reserved expansion deformation on the characteristics of swelling pressure in strong expansive soils, and also to explore the evolution mechanism of the swelling pressure. The findings demonstrate that the swelling pressure-time curve can be classified into swelling pressure-time softening and swelling pressure-time stability type. The swelling pressuretime curve of the specimen with low water content is the swelling pressure-time softening type, and the softening level will be weakened with increasing reserved expansion deformation. Besides, the maximum swelling pressure Psmax decreases with increasing water content and reserved expansion deformation, especially for expansion ratio η from 24% to 37%. The reserved deformation has little effect on reducing Psmax when it is beyond 7% of the expansion rate. The specimen with low water content has a more homogeneous structure due to the significant expansion-filling effect, and the fracture and reorganization of the aggregates in the specimens with low water content cause the swelling pressure-time softening behavior. In addition, the proposed swelling pressure-time curve prediction model has a good prediction on the test results. If necessary, a deformation space of about 7% expansion rate is recommended to be reserved in the engineering to reduce the swelling pressure except for keeping a stable water content.

Application of multi-algorithm ensemble methods in high-dimensional and small-sample data of geotechnical engineering:A case study of swelling pressure of expansive soils

Geotechnical engineering data are usually small-sample and high-dimensional,which brings a lot of challenges in predictive modeling.This paper uses a typical high-dimensional and small-sample swell pressure(P_(s))dataset to explore the possibility of using multi-algorithm hybrid ensemble and dimensionality reduction methods to mitigate the uncertainty of soil parameter prediction.Based on six machine learning(ML)algorithms,the base learner pool is constructed,and four ensemble methods,Stacking(SG),Blending(BG),Voting regression(VR),and Feature weight linear stacking(FWL),are used for the multi-algorithm ensemble.Furthermore,the importance of permutation is used for feature dimensionality reduction to mitigate the impact of weakly correlated variables on predictive modeling.The results show that the proposed methods are superior to traditional prediction models and base ML models,where FWL is more suitable for modeling with small-sample datasets,and dimensionality reduction can simplify the data structure and reduce the adverse impact of the small-sample effect,which points the way to feature selection for predictive modeling.Based on the ensemble methods,the feature importance of the five primary factors affecting P_(s) is the maximum dry density(31.145%),clay fraction(15.876%),swell percent(15.289%),plasticity index(14%),and optimum moisture content(13.69%),the influence of input parameters on P_(s) is also investigated,in line with the findings of the existing literature.

Influence of Temperature on the Inter-pressure of Soil Water Tension with Correcting Method

When the electronic temperature sensor was incorporated into a system of soil water tension and the insidetube temperature was monitored in real time, it is concluded that the inside temperature increased by 26.9 ℃ and the inside pressure changed about 14.6 Kpa, when the pottery soil was replaced by the sealing plug. When the soil water was relatively stable in the experimental salvers, the in-side pressure stil varied regularly with the temperature. When the inside temperature increased by 22.2 ℃, the inside pressure varied about 7.4 Kpa. Through com-pensation calculation of the inside tension, the temperature in the warming and cooling periods was compensated, which was useful to correct the tension measurement errors induced from the changing temperature. When the measuring interval was 4 hours and the temperature difference was 18.1 ℃, the tension difference of both points was only 0.278 Kpa, compared to the difference up to 6.5 Kpa before compensation.

Biological soil crust distribution in Artemisia ordosica communities along a grazing pressure gradient in Mu Us Sandy Land, Northern China

This study investigated the distribution pattern of biological soil crust （BSC） in Artemisia ordosica communities in Mu Us Sandy Land. Three experimental sites were selected according to grazing pressure gradient. In each experimental site, the total vegetation cover, A. ordosica cover, BSC cover, litter-fall cover, BSC degree of fragmentation, BSC thickness and soil properties were investigated in both fixed and semi-fixed sand dunes and simultaneously analyzed in the laboratory. The results showed that at the same grazing pressure, BSC cover and composition were significantly affected by the fixation degree of sand dunes. In addition, BSC cover in the fixed sand dunes was 83.74% on average, whereas it is proportionally dominated by 28% mosses, 21% lichens, and 51% algae. Meanwhile, BSC cover in the semi-fixed sand dunes was 23.54% on average, which is proportionally domi- nated by 6.3% mosses, 2.5% lichens, and 91.2% algae. Fine sand, organic matter, and total nitrogen （N） contents in the fixed sand dunes were all significantly higher than those in the semi-fixed sand dunes. Litter-fall cover de- creased along the grazing pressure gradient, whereas BSC fragmentation degree increased. Fine sand content decreased along with the increase of grazing pressure, whereas medium sand content increased in both fixed and semi-fixed dunes. The organic matter and total N contents in the no grazing site were significantly higher than those in light and normal grazing sites. However, there were no significant differences between the light and normal grazing sites. In addition, there were also no significant differences in BSC thickness between the light and normal grazing sites in the fixed sand dunes. However, a significant decrease was observed in both BSC cover and thick- ness in the normal grazing site. The BSC in the semi-fixed dunes was more sensitive to disturbance.

Wave-induced pore water pressure in marine cohesive soils

Cyclic triaxial tests and numerical analyses were undertaken, in order to evaluate the wave-induced pore water pressure in seabed sediments in the Hangzhou Bay. The cyclic triaxial tests indicate that the rate of pore water pressure generation in cohesive soils decreases with time, and the development of the pore water pressure can be represented by a hyperbolic curve. Numerical analyses, taking into account the generation and dissipation of pore water pressure simultaneously, suggest that the pore water pressure buildup in cohesive soils may increase with time continuously until the pore water pressure ratio approaches to 1, or it may decrease after a certain time, which is controlled by drain conditions. These phenomena are different from those in sands. For waves with a retum period of 100 a in the Hangzhou Bay, if the wave duration is more than 60 h, then the pore water pressure ratio will be close to 1 and soil fabric failure will take place.

Non-limit passive soil pressure on rigid retaining walls

This paper aims to reveal the depth distribution law of non-limit passive soil pressure on rigid retaining wall that rotates about the top of the wall(rotation around the top(RT) model). Based on Coulomb theory, the disturbance degree theory, as well as the spring-element model, by setting the rotation angle of the wall as the disturbance parameter, we establish both a depth distribution function for sand and a nonlinear depth distribution calculation method for the non-limit passive soil pressure on a rigid retaining wall under the RT model, which is then compared with experiment. The results suggest that under the RT model: the non-limit soil pressure has a nonlinear distribution; the backfill disturbance degree and the lateral soil pressure increase with an increase in the wall rotation angle; and, the points where the resultant lateral soil pressure acts on the retaining wall are less than 2/3 of the height of the wall. The soil pressure predicted by the theoretical calculation put forward in this paper are quite similar to those obtained by the model experiment, which verifies the theoretical value, and the engineering guidance provided by the calculations are of significance.

Soil pressure and pore pressure for seismic design of tunnels revisited: considering water-saturated, poroelastic half-space

This paper describes a systematic study on the fundamental features of seismic soil pressure on underground tunnels, in terms of its magnitude and distribution, and further identifi es the dominant factors that signifi cantly infl uence the seismic soil pressure. A tunnel embedded in water-saturated poroelastic half-space is considered, with a large variety of model and excitation parameters. The primary features of both the total soil pressure and the pore pressure are investigated. Taking a circular tunnel as an example, the results are presented using a fi nite element-indirect boundary element(FE-IBE) method, which can account for dynamic soil-tunnel interaction and solid frame-pore water coupling. The effects of tunnel stiffness, tunnel buried depth and input motions on the seismic soil pressure and pore pressure are also examined. It is shown that the most crucial factors that dominate the magnitude and distribution of the soil pressure are the tunnel stiffness and dynamic soil-tunnel interaction. Moreover, the solid frame-pore water coupling has a prominent infl uence on the magnitude of the pore pressure. The fi ndings are benefi cial to obtain insight into the seismic soil pressure on underground tunnels, thus facilitating more accurate estimation of the seismic soil pressure.

Water and salt movement in different soil textures under various negative irrigating pressures

supported by the National High-Tech R＆D Program of China （2013AA102901）

Coefficient of earth pressure at rest for normal,consolidated soils

In this study consecutive consolidated isotropically drained triaxial tests for the coefficient of earth pressure at rest(K_0) were carried out to investigate its rules of evolution as well as its strength characteristics for normal,consolidated saturated silt under high pressure.The tests results indicate that:1) for normal,consolidated saturated silt,K_0 values increase as the consolidation stress increases at high pressure levels,while the nonlinear characteristics of K_0 are inconspicuous compared to cohesive soils;2) the Jaky and Roscoe equations,used to calculate K_0,are only suitable for certain soils,but cannot represent these values for normal, consolidated saturated silt due to the variation in bilinear strength at high pressure;and 3) there are close relations between the nonlinear characteristics of K_0 and the void ratio,measured in the tests.Both share the same functional form while under pressure. Based on our experimental results,we developed an empirical linear model to interpret the rules of nonlinear variation for the coefficient of earth pressure at rest.

Comparative study on pullout behaviour of pressure grouted soil nails from field and laboratory tests

Pullout resistance of a soil nail is a critical parameter in design and analysis for geotechnical engineers. Due to the complexity of field conditions, the pullout behaviour of cement grouted soil nail in field is not well investigated. In this work, a number of field pullout tests of pressure grouted soil nails were conducted to estimate the pullout resistance of soil nails. The effective bond lengths of field soil nails were accurately controlled by a new grouting packer system. Typical field test results and the related comparison with typical laboratory test results reveal that the apparent coefficient of friction （ACF） decreases with the increase of overburden soil pressure when grouting pressure is constant, but increases almost linearly with the increase of grouting pressure when overburden pressure （soil depth） is unchanged. Water contents of soil samples at soil nail surfaces show obvious reductions compared with the results of soil samples from drillholes. After soil nails were completely pulled out of the ground, surface conditions of the soil nails and surrounding soil were examined. It is found that the water content values of the soil at the soil/nail interfaces decrease substantially compared with those of soil samples extracted from drillholes. In addition, all soil nails expand significantly in the diametrical direction after being pulled out of ground, indicating that the pressurized cement grout compacts the soil and penetrates into soil voids, leading to a corresponding shift of failure surface into surrounding soil mass significantly.

Evaluation of Inner Soil Pressure Acting on Opened Bottom Cylindrical Structure

An opened bottom cylinder is a large-diameter cylinder placed on a rubber base or embedded in a soil foundation. The settlement of such a cylinder differs greatly from that of a closed bottom cylinder and so does the distribution of inner soil pressure over the opened bottom cylindrical structure. Through investigation of the settlement and the inner soil pressure on the opened bottom cylinder by model experiments, the interactions among the filler inside the cylinder, subsoil and cylinder are analyzed. The adjusting mechanism of friction resistance between the inner filler and the wall of the cylinder during overturning of the cylinder is discussed. Based on the experimental study, a method for calculating the inner soil pressure on the cylindrical structure under axisymmetric loading or non- axisymmetric (with lateral) loading is proposed in this paper. Meanwhile, the effective anti-overturning ratio of the opened bottom cylinder is derived.

Coefficients of earth pressure at rest in thick and deep soils

The effect of test methods and stress paths on the experimental value of the coefficient of earth pressure at rest, K0, was investigated under high pressures. The results indicate that the rigid pressure chamber and flexible lateral confining pressure medium method gives a stress ratio at the initial stage that is not the real K0. Moreover, K0 increases during the loading process becoming greater at high pressures. In the unloading process, however, K0 increases only at the initial stage but decreases thereafter. In addition, the incremental magnitude definition, K0=dσ3/dσ1, gives higher values than the total magnitude definition, K0=σ3/σ1, under loading. This is also true during initial stages of unloading. The experiment results also indicate that earth pressure at rest in deep and thick soils can be estimated by a power function of axial and confining pressures. It is necessary to choose the appropriate Kn to avoid some accidents.

Effects of sample dimensions and shapes on measuring soil-water characteristic curves using pressure plate

It is well known that soilewater characteristic curve （SWCC） plays an important role in unsaturated soil mechanics, but the measurement of SWCC is inconvenient. In laboratory it requires days of testing time. For fine-grained clays, it may last for a couple of months using pressure plate tests. In this study, the effects of sample dimensions and shapes on the balance time of measuring SWCCs using pressure plate tests and the shape of SWCCs are investigated. It can be found that the sample dimensions and shapes have apparent influence on the balance time. The testing durations for circular samples with smaller diameters and annular samples with larger contact area are significantly shortened. However, there is little effect of sample dimensions and shapes on the shape of SWCCs. Its mechanism is explored and discussed in details through analysing the principle of pressure plate tests and microstructure of the sample. Based on the above findings, it is found that the circular samples with smaller dimensions can accelerate the testing duration of SWCC using the pressure plate.

Evaluation of Dynamic Soil-Structure Interaction and Dynamic Seismic Soil Pressures Acting on It Subjected to Strong Earthquake Motions

In order to clarify the damage mechanism of the subway structure, the dynamic soil-structure interaction and the dynamic forces acting on the structure, a series of shaking table tests and simulation analyses were performed. The seismic response of the structure and the dynamic forces acting on the structure due to sinusoidal and random waves were investigated with special attention to the dynamic soil-structure interaction. The result shows that the compression seismic soil pressures and extension seismic soil pressures simultaneously act on the sidewalls, and big shear stress also acts on the ceiling slab due to horizontal excitation. The seismic soil pressure could be approximated to hyperbola curve, and reached a peak value with increase of the shear strain of the model ground. In addition, a slide and exfoliation phenomenon between the structure and the surrounding ground was simulated, using the nonlinear analyses. The foundation is provided for amending the calculation method of seismic soil pressure and improving the anti-earthquake designing level of underground structure.

Determination of critical state line(CSL)for silty-sandy iron ore tailings subjected to low-high confining pressures

The disposal of filtered tailings in high dry stacks can induce particle breakage,changing the material's behaviour during the structure's lifetime.The grading changes influence material properties at the critical state,and this is not mature for intermediate artificial soils(tailings)in a broad range of confining pressures.In this paper,it aims to describe the behaviour of iron ore tailings in a spectrum of confining pressures broader than the reported in previous studies.A series of consolidated drained(CD)triaxial tests was carried out with confining pressures ranging from 0.075 MPa to 120 MPa.These results show that the amount of breakage plays an essential role in the response of iron ore tailings.The existence of curved critical state line(CSL)in both specific volume(ν)-logarithm of mean effective stress(p′)and deviatoric stress(q)-mean effective stress(p′)planes,and different responses in the deviatoric stress-axial strain-volumetric strain curves were verified.An inverse S-shaped equation was proposed to represent the silty-sandy tailings'behaviour up to high pressures onν-lnp′plane.The proposed equation provides a basis for enhancing constitutive models and considers the evolution of the grading up to severe loading conditions.The adjustment considered three regions with different responses associated with particle breakage at different pressure levels.

Experimental study on the wave pressure of liquefied silty soil

A number of studies focus on the pore-water pressure in seabed under thewaves and seabed instability induced by liquefaction, but rarely on the wave pressureof liquefied soil. In this paper, flume tests were performed at varying wave heightsunder both conditions of liquefied and stable seabed. The total pressures equal to soilpressures and pore water pressures were measured and analyzed at each depth. Theresults showed that the liquefied seabed had little difference from the stable seabed onthe peak pressures. However, the pressure amplitude of the liquefied soil increased byseveral to 10 times and decreased faster with increasing soil depths, compared with thestable soil. According to the experiments and further analysis, an empirical equationbetween pressure amplitude of the liquefied soil and wave parameters was put forwardunder the flume test. The results provide a valuable reference for engineeringapplications.

Experimental study on the pressure control of soil chamber in shield tunneling

A mathematical model of the soil pressure system in shield tunneling was proposed to optimize soil pressure control in the soil chamber, based on the constitutive relationship between strain and stress. The desired pressure is determined by using the finite element method. A linear quadratic constant state tracking problem was considered over an infinite time interval. The optimal control law was derived by differentiating the Hamilton function with respect to system input. In order to verify the effectiveness of the proposed mathematical model and optimal control law, an experimental study on the pressure control of the soil chamber in shield tunneling was conducted in a laboratory. The experiment results show that soil pressure in the soil chamber in shield tunneling can be accurately controlled.

An analytical p-y curve method based on compressive soil pressure model in sand soil

With the high-quality development of urban buildings,higher requirements are come up with for lateral bearing capacity of laterally loaded piles.Consequently,a more accurate analysis to predict the lateral response of the pile within an allowable displacement is an important issue.However,the current p-y curve methods cannot fully take into account the pile-soil interaction,which will lead to a large calculation difference.In this paper,a new analytical p-y curve is established and a finite difference method for determining the lateral response of pile is proposed,which can consider the separation effect of pile-soil interface and the coefficient of circumferential friction resistance.In particular,an analytical expression is developed to determine the compressive soil pressure by dividing the compressive soil pressure into two parts:initial compressive soil pressure and increment of compressive soil pressure.In addition,the relationship between compressive soil pressure and horizontal displacement of the pile is established based on the reasonable assumption.The correctness of the proposed method is verified through four examples.Based on the verified method,a parametric analysis is also conducted to investigate the influences of factors on lateral response of the pile,including internal friction angle,pile length and elastic modulus of pile.

Test on Muddy Soil Reinforcement by Negative Pressure and Electro-Osmosis Inside Cover-Bearing-Type Bucket Foundation for Offshore Wind Turbines

Cover-bearing-type bucket foundation for offshore wind turbines has been paid more and more attention due to its low cost and great bearing capacity. In order to ensure the cover-bearing mode, the muddy soil inside the bucket foundation should be reinforced by some soil consolidation methods, such as negative pressure and electro-osmosis. Firstly, tests were conducted to obtain the reasonable current density. Meanwhile, to improve the electro-osmotic speed and effectiveness, other factors such as intermittent power and layout of electrode, were also studied in the tests. Then, the soil reinforcing tests by negative pressure combined with electro-osmosis were performed for the muddy soil consolidation inside the bucket foundation. The results showed that soil reinforcement by negative pressure was quicker and more obvious during the early phase, and electro-osmotic method can affect more range of soil by rational arrangement of electrodes. Compared with negative pressure, the electro-osmotic method was a continuous and relatively slow process of reinforcement, which was complementary to the negative pressure method. The voltage value of electro-osmosis had little effect on the muddy soil reinforcement inside the bucket foundation, and 1.5 A was chosen as the most reasonable current value for scale model testing in the electro-osmotic method.