The Effect of Ignition Parameters on the Combustion Characteristics of an Aviation Piston Engine

A cylinder combustion simulation model was established for a two-stroke aviation piston engine used in a small unmanned aerial vehicle. The influence of different ignition system parameters on the combustion process of aviation kerosene was studied using this model. The research results showed that under the working conditions of 5500 r/min and 50% throttle opening, as the ignition energy increased, the peak values of average cylinder pressure and average temperature increased, and the combustion duration shortened, The advance of the combustion center of gravity increases the tendency of the engine to knock. Under the same operating conditions, as the ignition timing advances, the peak values of average pressure and average temperature in the cylinder increase, gradually approaching the top dead center, and the tendency of engine detonation increases more significantly.

Fuzzy Control Method for Gasoline Engine Idle Speed Control

In order to improve the steady and dynamic characteristic of the idle speed control and study the performance of the fuzzy control method for the idle speed control, a fuzzy control system is developed to control the idle speed of gasoline engine. The construction and working principle of the fuzzy controller are described, and the design procedure of the fuzzy controller is given in detail. The control parameters are determined by computer simulation. The simulation and experiments on the engine test bench show that the idle speed is controlled accurately both in stationary and in dynamic states, and the fuzzy control method is robust to the changes of engine parameters.

Mixture formation analysis of an opposed-piston two-stroke gasoline-direct-injection engine

The effects of different flow forms on an opposed-piston two-stroke（OPTS）gasoline-directinjection（GDI）engine was studied by analyzing the mixture formation and combustion.Swirl was broken and dissipated gradually and the turbulence kinetic energy（TKE）was small in the compression process;however,tumble was strengthened and the TKE was strong in the compression process.For swirl around X axis（the axis of cylinder）and tumble around Y axis（the vertical direction of injector）,droplets were attached to the cylinder liner by the centrifugal force and the mixture distribution was poor.For tumble around Zaxis（the direction of injector）,the wall film in cylinder liner was thin and mixture distribution was homogeneous.Results showed that since the injector were installed on the wall of the cylinder liner in the OPTS-GDI engine,the spray angle was small and the mixture formation time was short.The 45° oblique axis tumble ratio of 1 was reasonable for the mixture formation and combustion for an OPTS-GDI engine.

Effect of Nozzle Inclination Angle on Fuel-Air Mixing and Combustion in a Heavy Fuel Engine

Heavy-fuel engines are widely used in UAVs(Unmanned Autonomous Vehicles)because of their reliability and high-power density.In this study,a combustion model for an in-cylinder direct injection engine has been imple-mented using the AVL FIRE software.The effects of the angle of nozzle inclination on fuel evaporation,mixture distribution,and combustion in the engine cylinder have been systematically studied at 5500 r/min and consider-ing full load cruise conditions.According to the results,as the angle of nozzle inclination increases,the maximum combustion explosion pressure in the cylinderfirst increases and then it decreases.When the angle of nozzle incli-nation is less than 45°,the quality of the mixture in the cylinder and the combustion performance can be improved by increasing the angle.When the angle of nozzle inclination is greater than 45°,however,the mixture unevenness increases slightly with the angle,leading to a deterioration of the combustion performances.When the angle of nozzle inclination is between 35°and 55°,the overall combustion performance of the engine is rela-tively good.When the angle of nozzle inclination is 45°,the combustion chamber’s geometry and the cylinder’s airflow are well matched with the fuel spray,and the mixture quality is the best.Compared with 25°,the peak heat release rate increases by 20%,and the maximum combustion burst pressure increases by 5.5%.

STUDY ON INJECTION AND IGNITION CONTROL OF GASOLINE ENGINE BASED ON BP NEURAL NETWORK

According to advantages of neural network and characteristics of operatingprocedures of engine, a new strategy is represented on the control of fuel injection and ignitiontiming of gasoline engine based on improved BP network algorithm. The optimum ignition advance angleand fuel injection pulse band of engine under different speed and load are tested for the samplestraining network, focusing on the study of the design method and procedure of BP neural network inengine injection and ignition control. The results show that artificial neural network technique canmeet the requirement of engine injection and ignition control. The method is feasible for improvingpower performance, economy and emission performances of gasoline engine.

Effects of working parameters on gasoline engine exergy balance

To improve the energy utilization efficiency of internal combustion （IC） engine, exergy analysis was conducted on a passenger car gasoline engine. According to the thermodynamic theory of IC engine, in-cylinder exergy balance model was built. The working processes of gasoline engine were simulated by using the GT-power. In this way, the required parameters were calculated and then gasoline engine exergy balance was obtained by programming on computer. On this basis, the influences of various parameters on exergy balance were analyzed. Results show that, the proportions of various forms of exergy in gasoline engine from high to low are irreversible loss, effective work, exhaust gas exergy and heat transfer exergy. Effective exergy proportion fluctuates with cylinder volumetric efficiency at full load, while it always increases with break mean effective pressure （BMEP） at part load. Exhaust gas exergy proportion is more sensitive to speed, and it increases with speed increasing except at the highest speed. The lower proportion of heat transfer exergy appears at high speed and high load. Irreversible loss is mainly influenced by load. At part load, higher BMEP results in lower proportion of irreversible loss; at full load, the proportion of irreversible loss changes little except at the highest speed.

Comparative Effect of Gasoline Formulations on Fuel Economy and Emissions of Modern GDI Engine

In this paper the effect of gasoline formulations on fuel economy and emissions were studied,aiming at exploring the optimized fuel formulation that can alleviate energy crisis and greenhouse effect to some extent.Five gasoline blends with same research octane number(RON)were designed and tested on a calibrated gasoline direct injection(GDI)engine under the mapped characteristic conditions.Test results illustrate that the optimized fuel formulation shows good superiority in fuel economy,and reduces carbon dioxide(CO2)emissions at low engine speeds with medium loads.The brake-specific fuel consumption(BSFC)decreased by a maximum value of 3.26%mainly because of the improvement of combustion velocity and the optimization of low heating value.The optimized fuel formulation simultaneously increases total hydrocarbon(THC)emissions.Nevertheless,it also markedly reduces CO2 emissions,reaching the maximum value of 2.34%.The research results can be applied practically by refineries to reduce the CO2 emissions and to alleviate the greenhouse effect.

A comparison of hydrocarbons emission from engine running 85￣＃gasoline and M－100 methanol fuel

Increasing global interest in methanoi fuel has led us to investigate the exhaust emissionsof its engine. Analysis of its inorganic and organic emissions. such as CO. NO_x and hydrocarbons(total HC) have been widely reported. This paper presents an analysis of more than 20 kinds ofhydrocarbons in the emissions obtained from a spark-ignition Shanghai car running 85# gasoline anda comparison with emission from a Santana test car running M-100 methanol fuel. A set ofenrichment method has also been described. Test results show that at the current stage of methanolengine development the concentration of individual hydrocarbon including some poisonous substancesis lower than those of normal gasoline engine.

Monolithic Catalysts with Low Noble-Metal Content for Exhaust Purification of Small Gasoline Engines

A series of low noble-metal coment monolithic catalysts for exhaust purification of small gasoline engines was investigated, and it was found that the Pt/Rh-OSM/Al2O3 （where OSM was oxygen storage material） catalyst with Ce0.5Zr0.5-MnOx（3%MnOx） OSM held low light-off temperature for CO, HC, and NO; quite wide three-way window, and outstanding thermal stability. The catalyst could efficiently comrol exhaust emission of small gasoline engines.

Turbocharging the DA465 gasoline engine

In order to improve performance of the DA465Q gasoline engine, a substantial amount of research was done to optimize its turbocharging system. The research led to the GT12 turbocharger being selected and its turbocharging parameters being settled. Based on these tests, rational matching was worked out for respective components of the turbocharging system. Results show that this turbocharger allows the engine to easily meet the proposed requirements for power and economic performance, giving insight into further performance improvements for gasoline engines.

RIPP Grasps the Techniques for Manufacturing the Latest-Generation Gasoline Engine Oils

Recently,the gasoline engine oil developed by the SINOPEC Research Institute of Petroleum Processing(RIPP)has passed seven engine tests required by the latest-generation gasoline engine oil standard GF-6/SP.Meanwhile,RIPP has brought forward the technology for manufacture of new generation gasoline engine oil based on its own formulation meeting the engine oil standard GF-6/SP simultaneously with the international additives companies,which has eliminated the new generation gap in gasoline engine oil between China and the overseas players.

Auto-Ignition and Heat Release Correlations for Controlled Auto-Ignition Combustion in Gasoline Engines

Auto-ignition and heat release correlations for controlled auto-ignition(CAI)combustion were derived from extensive in-cylinder pressure data of a four-stroke gasoline engine operating in CAI combustion mode.Abundant experiments were carried out under a wide range of air/fuel ratio,speed and residual gas fraction to ensure that the combustion correlations can be used in the entire CAI engine operation range.Furthermore,a more accurate method to compute the residual gas fraction was proposed by calculating the working fluid temperature at the exhaust valve close timing in the experiments.The heat release correlation was described in two parts,one is for the first slower heat release process at low temperature,and the other is for the second faster heat release process at high temperature.Finally the heat release correlation was evaluated on the single cylinder gasoline engine running with CAI combustion by comparing the experimental data with the 1-D engine simulation results obtained with the aid of the GT-Power simulation program.The results show that the predicted loads and ignition timings match closely with the measurements.

Performance Evaluation of Spark Ignited Engine Fueled with Gasoline-Ethanol-Methanol Blends

In this paper, experimental investigations are presented to assess the performance variations in a single cylinder spark ignited engine when run with three different gasoline-alcohol blends： （88% gasoline-12% methanol, 88% gasoline-12% ethanol and 88% gasoline-6% methanol-6% ethanol）. Additional tests are carried out with the basic gasoline fuel for comparison analysis and performance assessment. Engine performance is investigated under a variety of engine operating conditions. The results are presented in the domain of engine speed. In particular, the brake power of the engine is shown to be slightly increased. The brake thermal efficiency showed an increase compared with the basic gasoline engine. Similarly, it is shown that brake specific fuel consumption is enhanced compared with basic gasoline engine. The exhaust gas temperature showed a decrease compared with gasoline fuel which is preferable to reduce emissions. The alcohol additives are strongly recommended to enhance performance, increasing the mileage and reducing the emissions.

Study on Using Mixed Fuel of Jet Fuel/Gasoline as Fuel of Gasoline Engine

This paper has integrated various methods such as laboratory physical and chemical analysis, engine bench test and actual road test, etc. to conduct a feasibility study on the emergency alternative fuel of gasoline by mixed jet fuel and gasoline. The study shows that both the evaporability and anti-knock quality decrease after mixing jet fuel with gasoline. While the mixing proportion increases, the engine power decreases and the fuel consumption increases gradually. When the proportion reaches 40%, the engine power drops by 5.3% to 11.7%, the fuel consumption rises by an average of 3.8%, and meantime the oil dilution and emission of the engine power become worse. Therefore, as for the gasoline engine, the mixed oil can only be used as emergency alternative fuel due to its harm to the engine.

Comparison of two types of twin-rotor piston engine mechanisms

A novel twin-rotor piston engine （TRPE） mechanism with high volumetric output and power density was introduced. This new engine comprises an energy conversion system and a differential velocity drive mechanism （DVDM）. Two special geared four-bar mechanisms, DVDM-1 and DVDM-2, were utilized and compared. Based on the closed loop vector method, a mathematical model for position, velocity, and acceleration of the two mechanisms was established. Numerical examples illustrate that the kinematic characteristics were presented. Expression of the displacement and compression ratio of the two engine mechanisms were derived and compared. It is concluded that both DVDM-1 and DVDM-2 adopted in the proposed TRPE with six vane pistons create thirty-six power strokes per revolution of the output shaft, and the summation of two angles covered by each rocker is always 2x/N as the output shaft rotates an angle of x/N. In DVDM-1, the span angle of a vane piston should be designed to be 10.2°, and the compression ratio should be equal to 10; in DVDM-2, the span angle of a vane piston should be designed to be 10.6°, and the compression ratio should be equal to 4.3.

Asymmetric vibration characteristics of two-cylinder four-stroke single-piston hydraulic free piston engine

The structure and working principle of a two-cylinder four-stroke single-piston hydraulic free piston engine(HFPE) were introduced. The basic vibration equation of free piston assembly(FPA) was established based upon the energy conversion between the injected fuel and the friction together with the load. Both the theoretical and numerical results show that the vibration system of FPA is a nonlinear conservative autonomous system in one cycle. The FPA vibration is symmetric with constant amplitude when FPA is only driven by the compression pressure in the compression accumulator and that in the combustion chamber. When considering the friction and load, FPA could still achieve a stable vibration after a few cycles' adjustment whether the input energy is equal to the consumed energy or not. The vibration characteristics are different when FPA vibrates in the compression stroke and the expansion stroke, which is the unique feature of the single-piston HFPE.

Analysis of Oil Consumption in Cylinder of Diesel Engine for Optimization of Piston Rings

The performance and particulate emission of a diesel engine are affected by the consumption of lubricating oil. Most studies on oil consumption mechanism of the cylinder have been done by using the experimental method, however they are very costly. Therefore, it is very necessary to study oil consumption mechanism of the cylinder and obtain the accurate results by the calculation method. Firstly, four main modes of lubricating oil consumption in cylinder are analyzed and then the oil consumption rate under common working conditions are calculated for the four modes based on an engine. Then, the factors that affect the lubricating oil consumption such as working conditions, the second ring closed gap, the elastic force of the piston rings are also investigated for the four modes. The calculation results show that most of the lubricating oil is consumed by evaporation on the liner surface. Besides, there are three other findings： （1） The oil evaporation from the liner is determined by the working condition of an engine; （2） The increase of the ring closed gap reduces the oil blow through the top ring end gap but increases blow-by; （3） With the increase of the elastic force of the ring, both the left oil film thickness and the oil throw-off at the top ring decrease. The oil scraping of the piston top edge is consequently reduced while the friction loss between the rings and the liner increases. A neural network prediction model of the lubricating oil consumption in cylinder is established based on the BP neural network theory, and then the model is trained and validated. The main piston rings parameters which affect the oil consumption are optimized by using the BP neural network prediction model and the prediction accuracy of this BP neural network is within 8%, which is acceptable for normal engineering applications. The oil consumption is also measured experimentally. The relative errors of the calculated and experimental values are less than 10%, verifying the validity of the simulation results. Applying the established simulation model and the validated BP network model is able to generate numerical results with sufficient accuracy, which significantly reduces experimental work and provides guidance for the optimal design of the piston rings diesel engines.

Combustion simulation and key parameter optimization for opposite axial piston engine in small-scale

As potential alternative power sources used in portable electric generators, opposite axial piston engines in small-scale were investigated to show their advantages in power density. A novel cylinder charge system was introduced, based on which a quasi-dimension model and a CFD(computational fluid dynamics) model were established. Comparison of those two models was carried out to validate the quasi-dimension model. Furthermore, optimal diameter of charge cylinder and speed were determined after evaluating the quasi-dimension model based on different parameters. High agreement between the quasi-dimension model and the CFD model validates the quasi-dimension model. Further studies show that the power of engine increases with the diameter of charge cylinder. However, a too big charge cylinder lowers the fuel efficiency instead. Taking economic influence into consideration the charge cylinder should be 1.4 times power cylinder, which could ensure the power density, volumetric efficiency and fuel economic at the same time. Axial piston engine running at 1.0×104 r/min could achieve a better overall performance. The maximal power of engine with optimal parameters is 0.82 k W, which fits the power need of the portable electric generators completely.

Multi-body dynamic simulation research on the influence of piston engine crankshaft thrust bearings abrasion

Fault diagnosis studying on piston engine,crankshaft and gearbox is focused in this paper. The thrust bearing abrasion caused by axial movement of the crankshaft will affect the force of timing gears and oil pump gears,which will result in the fracture of gears,abnormal ignition,connecting rod cracking and collision of cylinder. Simulation based on CREO software is done to build three-dimensional models of crankshaft and gears of a WP10 diesel engine. The models are imported into ADAMS to complete multi-body dynamics simulations. The force analysis of gears in different kinds of axial movements is finished and variations rules of gear dynamic load is obtained. The presented results show that the crankshaft axial movement can cause overload and vibration on gears. Combined with the realistic case data,the fault feature through simulation research is validated and early warming parameters of gear fault are proposed.

Sensitivity and effect of key operational parameters on performance of a dual-cylinder free-piston engine generator

The free-piston engine generator(FPEG)is regarded as the next generation of energy conversion system which may replace traditional engines in the future.The effect of key operational parameters like excess air ratio of input mixture and ignition position on the engine performance of a dual-cylinder FPEG was investigated,and their sensitivity was analyzed in this paper.The operating compression ratio of the system is susceptible to changes in excess air ratio and ignition position.At the same time,it decreases from 15.8 to 6.6 when excess air ratio increases from 0.85 to 1.15,but it increases from 6.1 to 13.3 as ignition position increases from 15 mm to 20 mm.The operating frequency and indicated power are more sensitive to changes in excess air ratio than ignition position.But it is the opposite for the indicated thermal efficiency and friction loss.Excess air ratio and ignition position have a quite similar influence on heat transfer.Therefore,from the perspective of system operation and performance,it is preferable to keep excess air coefficient slightly below 1.0.In contrast,when selecting ignition position,it is of great importance to comprehensively consider the risk of structural damage caused by the increase in the compression ratio and in-cylinder gas pressure.