Numerical Simulation of the Impact of Urban Non-uniformity on Precipitation

To evaluate the influence of urban non-uniformity on precipitation, the area of a city was divided into three categories （commercial, high-density residential, and low-density residential） according to the building density data from Landsat satel- lites. Numerical simulations of three corresponding scenarios （urban non-uniformity, urban uniformity, and non-urban） were performed in Nanjing using the WRF model. The results demonstrate that the existence of the city results in more precip- itation, and that urban heterogeneity enhances this phenomenon. For the urban non-uniformity, uniformity, and non-urban experiments, the mean cumulative summer precipitation was 423.09 mm, 407.40 mm, and 389.67 mm, respectively. Urban non-uniformity has a significant effect on the amount of heavy rainfall in summer. The cumulative precipitation from heavy rain in the summer for the three numerical experiments was 278.2 mm, 250.6 mm, and 236.5 mm, respectively. In the non- uniformity experiments, the amount of precipitation between 1500 and 2200 （LST） increased significantly. Furthermore, the adoption of urban non-uniformity into the WRF model could improve the numerical simulation of summer rain and its daily variation.

Radial Non-uniformity Index Research on High-density,High-flux CFB Riser with Stratified Injection

A high-density, high-flux circulating fluidized bed （CFB） riser （100 mm in ID and 10.614 m in height） was ap- plied in a wide range of operating conditions （with solid fluxes up to 400 kg/m2s and superficial gas velocities up to 12 m/s） to examine its radial non-uniformity dynamics. The solids holdup was determined through the use of a fiber-optic probe at 11 axial levels. The results indicated that under all operating conditions, the high superficial gas velocity and low solid flux- es maintained a low radial non-uniformity index （RNI）. The high-density/flux CFB riser had several unique characteristics, so that the peak of the radial solids holdup profile occurred at a position with r/R=0.8. The RNI and solids holdup at the cross-sectional position had a good logarithmic relationship at the low-density condition （with a mean solids holdup of 〈0.2）, and the RNI decreased when the mean solids holdup exceeded 0.2. Investigation of the dynamics of stratified injec- tion revealed that the feed ratio had an important effect on G, and on solids holdup distribution. A novel ＂〈＂ shaped axial solids holdup profile was found. Gs decreased sharply when the up-flow feed ratio exceeded 0.5, and RNI was lowest when the up-flow feed ratio was 1.

结合Pixel2style2Pixel的年龄转化方法

年龄转化在刑侦、人脸识别等领域有着重要作用。常见的年龄转化方法需要使用成对带有年龄注释的数据集进行训练,并且存在生成图像质量低、年龄语义信息不够解耦等问题。针对上述问题,在Pix2style2Pix的训练框架中,引入年龄识别、contextual损失函数,对整体损失函数做出符合年龄转化的改进,提取年龄信息并保证图像质量。改进编码网络配合损失函数对潜在空间的图像进行编辑,提出一种基于Pixel2style2Pixel的年龄转化方法。通过FFHQ、CelebA数据集,对所提方法进行验证,实验结果表明,在不采用成对年龄注释的训练集下,改进后的损失函数能生成更符合期望年龄的转化图像,人脸相似度距离为0.346、FID为45.69、SSIM为0.593 6、PSNR为19.64 dB,均优于对比方法,证明所提方法能够生成高质量、年龄语义高度解耦的转化结果。

Effect of heat transfer space non-uniformity of combustion chamber components on in-cylinder soot emission formation in diesel engine

Combustion chamber components （cylinder head, cylinder liner, piston assembly and oil film） are treated as a coupled body. Based on the three-dimensional numerical simulation of heat transfer of the coupled body, a coupled three-dimensional calculation model for the in-cylinder working process and the combustion chamber components was built with domain decomposition and boundary coupling method, in which the coupled three-dimensional simulation of in-cylindcr working process and the combustion chamber components was adopted. The simulation was applied in the influence investigation of the space non-uniformity in heat transfer among combustion chamber components on the generation of in-cylinder emissions. The results show that the space non-uniformity in heat transfer among the combustion chamber components has great influence on the generation of in-cylinder NOx emissions. The heat transfer space non-uniformity of combustion chamber components has little effect on soot formation, and far less effect on soot formation than on NOx. Under two situations of different wall temperature distributions, the soot in cylinder is different by 1.3% when exhaust valves are open.

Study on effect of heat transfer space non-uniformity of combustion chamber components on in-cylinder NOx emission formation in internal combustion engine

The components of combustion chamber (cylinder head-cylinder liner-piston assembly-oil film) were taken as a coupled body.Based on the three-dimensional heat transfer numerical simulation of the coupled body,a coupled three-dimensional calculation model for in-cylinder working process and the combustion chamber components was built with domain decomposition and boundary coupled method,which implements the coupled three-dimensional simulation of in-cylinder working process and the combustion chamber components.The model was applied in the influence investigation of the space non-uniformity in heat transfer among combustion chamber components on the generation of in-cylinder emissions:NOx.The results showed that the heat transfer space non-uniformity of combustion chamber components directly influences the formation of in-cylinder NOx.The main area being influenced was the accessory area on the wall,while the influence on the generation of NOx in the central area couold be omitted.

Improved Non-uniformity Correction Method for Uncooled Microbolometer

The uncooled microbolometer has a severe temperature requirement for non-uniformity correction. An improved two-point non-uniformity correction method is proposed, which can operate in wider uniform substrate temperatures. This method can control the bias voltage of MOS transistors by memory and DAC to meet two restrictions about responsivity and offset before traditional two-point calibration is implemented. The simulation results seem that this non-uniformity correction can work at uniform substrate temperature with fluctuant range of 4K.

The coefficient of variation representing the non-uniformity of the strain field and its implication to detect earthquake precursor

Before the major earthquake or rock damage occurs,it is often accompanied by a sudden change in the degree of non-uniformity of the strain field.In order to find a stronger non-uniformity signal before the rock failure,the coefficient of variation(Cv)is examined and reformed in this study.We test the Cv calculation way of the"normal-abnormal"model proposed in the previous studies.Based on the analysis of the physical process of rock failure and its relationship to the shear strain field,we construct a new way to calculate the Cv value.The variation of shear strain field on rock sample with the increase of stress is obtained by the digital speckle correlation method(DSCM).The new Cv value calculation way is used to study the non-uniformity of the spatial distribution for the shear strain field.The results show that this Cv calculation way can get more obvious abnormal signals.When the number of observation points are limited,the specific distribution of points can increase the signal strength,which may provide reference for the research on precursor detection of earthquakes.

Non-Uniformity of Heavy-Ion Beam Irradiation on a Direct-Driven Pellet in Inertial Confinement Fusion

Heavy-ion-driven fusion （HIF） is a scheme to achieve inertial confinement fusion （ICF）. Investigation of the non-uniformity of heavy-ion beam （HIB） irradiation is one of the key issues for ICF driven by powerful heavy-ion beams. Ions in HIB impinge on the pellet surface and deposit their energy in a relatively deep and wide area. Therefore, the non-uniformity of HIB irradiation should be evaluated in the volume of the deposition area in the absorber layer. By using the OK1 code with some corrections, the non-uniformity of heavy-ion beam irradiation for the different ion beams on two kinds of targets were evaluated in 12-beam, 20-beam, 60-beam and 120-beam irradiation schemes. The root-mean-square （RMS） non-uniformity value becomes aRMS = 8.39% in an aluminum mono-layer pellet structure and aRMS = 6.53% in a lead-aluminum layer target for the 12-uranium-beam system. The RMS non-uniformity for the lead-aluminum layer target was lower than that for the mono-layer target. The RMS and peak-to-valley （PTV） non-uniformities are reduced with the increase in beam number, and low at the Bragg peak layer.

Failure mechanisms and destruction characteristics of cemented coal gangue backfill under compression effect of non-uniform load

Backfill mining is one of the most important technical means for controlling strata movement and reducing surface subsidence and environmental damage during exploitation of underground coal resources. Ensuring the stability of the backfill bodies is the primary prerequisite for maintaining the safety of the backfilling working face, and the loading characteristics of backfill are closely related to the deformation and subsidence of the roof. Elastic thin plate model was used to explore the non-uniform subsidence law of the roof, and then the non-uniform distribution characteristics of backfill bodies’ load were revealed. Through a self-developed non-uniform loading device combined with acoustic emission (AE) and digital image correlation (DIC) monitoring technology, the synergistic dynamic evolution law of the bearing capacity, apparent crack, and internal fracture of cemented coal gangue backfills (CCGBs) under loads with different degrees of non-uniformity was deeply explored. The results showed that: 1) The uniaxial compressive strength (UCS) of CCGB increased and then decreased with an increase in the degree of non-uniformity of load (DNL). About 40% of DNL was the inflection point of DNL-UCS curve and when DNL exceeded 40%, the strength decreased in a cliff-like manner;2) A positive correlation was observed between the AE ringing count and UCS during the loading process of the specimen, which was manifested by a higher AE ringing count of the high-strength specimen. 3) Shear cracks gradually increased and failure mode of specimens gradually changed from “X” type dominated by tension cracks to inverted “Y” type dominated by shear cracks with an increase in DNL, and the crack opening displacement at the peak stress decreased and then increased. The crack opening displacement at 40% of the DNL was the smallest. This was consistent with the judgment of crack size based on the AE b-value, i. e., it showed the typical characteristics of “small b-value-large crack and large b-value-small crack”. The research results are of significance for preventing the instability and failure of backfill.

Study of the pressure transient behavior of directional wells considering the effect of non-uniform flux distribution

During the production,the fluid in the vicinity of the directional well enters the wellbore with different rates,leading to non-uniform flux distribution along the directional well.However,in all existing studies,it is oversimplified to a uniform flux distribution,which can result in inaccurate results for field applications.Therefore,this paper proposes a semi-analytical model of a directional well based on the assumption of non-uniform flux distribution.Specifically,the direction well is discretized into a carefully chosen series of linear sources,such that the complex well trajectory can be captured and the nonuniform flux distribution along the wellbore can be considered to model the three-dimensional flow behavior.By using the finite difference method,we can obtain the numerical solutions of the transient flow within the wellbore.With the aid of Green's function method,we can obtain the analytical solutions of the transient flow from the matrix to the wellbore.The complete flow behavior of a directional well is perfectly represented by coupling the above two types of transient flow.Subsequently,on the basis of the proposed model,we conduct a comprehensive analysis of the pressure transient behavior of a directional well.The computation results show that the flux variation along the direction well has a significant effect on pressure responses.In addition,the directional well in an infinite reservoir may exhibit the following flow regimes:wellbore afterflow,transition flow,inclined radial flow,elliptical flow,horizontal linear flow,and horizontal radial flow.The horizontal linear flow can be observed only if the formation thickness is much smaller than the well length.Furthermore,a dip region that appears on the pressure derivative curve indicates the three-dimensional flow behavior near the wellbore.

Effect of non-uniform swelling on coal multiphysics during gas injection: The triangle approach

In current dual porosity/permeability models,there exists a fundamental assumption that the adsorption-induced swelling is distributed uniformly within the representative elementary volume (REV),irrespective of its internal structures and transient processes.However,both internal structures and transient processes can lead to the non-uniform swelling.In this study,we hypothesize that the non-uniform swelling is responsible for why coal permeability in experimental measurements is not only controlled by the effective stress but also is affected by the adsorption-induced swelling.We propose a concept of the swelling triangle composed of swelling paths to characterize the evolution of the non-uniform swelling and serve as a core link in coupled multiphysics.A swelling path is determined by a dimensionless volumetric ratio and a dimensionless swelling ratio.Different swelling paths have the same start and end point,and each swelling path represents a unique swelling case.The swelling path as the diagonal of the triangle represents the case of the uniform swelling while that as the two perpendicular boundaries represents the case of the localized swelling.The paths of all intermediate cases populate inside the triangle.The corresponding relations between the swelling path and the response of coal multiphysics are established by a non-uniform swelling coefficient.We define this method as the triangle approach and corresponding models as swelling path-based ones.The proposed concept and models are verified against a long-term experimental measurement of permeability and strains under constant effective stress.Our results demonstrate that during gas injection,coal multiphysics responses have a close dependence on the swelling path,and that in both future experiments and field predictions,this dependence must be considered.

Effect of multiple coulomb scattering on the beam tests of silicon pixel detectors

In the research and development of new silicon pixel detectors,a collimated monoenergetic charged-particle test beam equipped with a high-resolution pixel-beam telescope is crucial for prototype verification and performance evaluation.When the beam energy is low,the effect of multiple Coulomb scattering on the measured resolution of the Device Under Test(DUT)must be considered to accurately evaluate the performance of the pixel chips and detectors.This study aimed to investigate the effect of multiple Coulomb scattering on the measured resolution,particularly at low beam energies.Simulations were conducted using Allpix^(2) to study the effects of multiple Coulomb scattering under different beam energies,material budgets,and telescope layouts.The simulations also provided the minimum energy at which the effect of multiple Coulomb scattering could be ignored.Compared with the results of a five-layer detector system tested with an electron beam at DESY,the simulation results were consistent with the beam test results,confirming the reliability of the simulations.

Image Non-Uniformity Correction in 3T Gd-EOB-DTPA-Enhanced Magnetic Resonance Imaging: Comparison among Different Software Versions

Background: Non-uniformity in signal intensity occurs commonly in magnetic resonance (MR) imaging, which may pose substantial problems when using a 3T scanner. Therefore, image non-uniformity correction is usually applied. Purpose: To compare the correction effects of the phased-array uniformity enhancement (PURE), a calibration-based image non-uniformity correction method, among three different software versions in 3T Gd-EOB-DTPA-enhanced MR imaging. Material and Methods: Hepatobiliary-phase images of a total of 120 patients who underwent Gd-EOB-DTPA-enhanced MR imaging on the same 3T scanner were analyzed retrospectively. Forty patients each were examined using three software versions (DV25, DV25.1, and DV26). The effects of PURE were compared by visual assessment, histogram analysis of liver signal intensity, evaluation of the spatial distribution of correction effects, and evaluation of quantitative indices of liver parenchymal enhancement. Results: The visual assessment indicated the highest uniformity of PURE-corrected images for DV26, followed by DV25 and DV25.1. Histogram analysis of corrected images demonstrated significantly larger variations in liver signal for DV25.1 than for the other two versions. Although PURE caused a relative increase in pixel values for central and lateral regions, such effects were weaker for DV25.1 than for the other two versions. In the evaluation of quantitative indices of liver parenchymal enhancement, the liver-to-muscle ratio (LMR) was significantly higher for the corrected images than for the uncorrected images, but the liver-to-spleen ratio (LSR) showed no significant differences. For corrected images, the LMR was significantly higher for DV25 and DV26 than for DV25.1, but the LSR showed no significant differences among the three versions. Conclusion: There were differences in the effects of PURE among the three software versions in 3T Gd-EOB-DTPA-enhanced MR imaging. Even if the non-uniformity correction method has the same brand name, correction effects may differ depending on the software version, and these differences may affect visual and quantitative evaluations.

Pressure transient characteristics of non-uniform conductivity fractured wells in viscoelasticity polymer flooding based on oil-water two-phase flow

Polymer flooding in fractured wells has been extensively applied in oilfields to enhance oil recovery.In contrast to water,polymer solution exhibits non-Newtonian and nonlinear behavior such as effects of shear thinning and shear thickening,polymer convection,diffusion,adsorption retention,inaccessible pore volume and reduced effective permeability.Meanwhile,the flux density and fracture conductivity along the hydraulic fracture are generally non-uniform due to the effects of pressure distribution,formation damage,and proppant breakage.In this paper,we present an oil-water two-phase flow model that captures these complex non-Newtonian and nonlinear behavior,and non-uniform fracture characteristics in fractured polymer flooding.The hydraulic fracture is firstly divided into two parts:high-conductivity fracture near the wellbore and low-conductivity fracture in the far-wellbore section.A hybrid grid system,including perpendicular bisection(PEBI)and Cartesian grid,is applied to discrete the partial differential flow equations,and the local grid refinement method is applied in the near-wellbore region to accurately calculate the pressure distribution and shear rate of polymer solution.The combination of polymer behavior characterizations and numerical flow simulations are applied,resulting in the calculation for the distribution of water saturation,polymer concentration and reservoir pressure.Compared with the polymer flooding well with uniform fracture conductivity,this non-uniform fracture conductivity model exhibits the larger pressure difference,and the shorter bilinear flow period due to the decrease of fracture flow ability in the far-wellbore section.The field case of the fall-off test demonstrates that the proposed method characterizes fracture characteristics more accurately,and yields fracture half-lengths that better match engineering reality,enabling a quantitative segmented characterization of the near-wellbore section with high fracture conductivity and the far-wellbore section with low fracture conductivity.The novelty of this paper is the analysis of pressure performances caused by the fracture dynamics and polymer rheology,as well as an analysis method that derives formation and fracture parameters based on the pressure and its derivative curves.

An improved non-uniform fast Fourier transform method for radio imaging of coronal mass ejections

Radioheliographs can obtain solar images at high temporal and spatial resolution,with a high dynamic range.These are among the most important instruments for studying solar radio bursts,understanding solar eruption events,and conducting space weather forecasting.This study aims to explore the effective use of radioheliographs for solar observations,specifically for imaging coronal mass ejections(CME),to track their evolution and provide space weather warnings.We have developed an imaging simulation program based on the principle of aperture synthesis imaging,covering the entire data processing flow from antenna configuration to dirty map generation.For grid processing,we propose an improved non-uniform fast Fourier transform(NUFFT)method to provide superior image quality.Using simulated imaging of radio coronal mass ejections,we provide practical recommendations for the performance of radioheliographs.This study provides important support for the validation and calibration of radioheliograph data processing,and is expected to profoundly enhance our understanding of solar activities.

Pixel激光治疗面部痤疮瘢痕

目的:观察Pixel激光治疗面部痤疮瘢痕的临床效果。方法:采用以色列飞顿2940nm像素激光对54例痤疮瘢痕的患者进行治疗,共治疗3～5次,每次间隔时间2～3周。除少数对疼痛敏感的患者治疗前外涂表面麻醉,其余不用任何处理。对比治疗前后的照片并进行疗效评价。结果:共治疗54例痤疮瘢痕患者,有效率75%～100%。Pixel同时可以有效改善4种不同类型痤疮,无一例色沉和瘢痕。结论:Pixel激光治疗痤疮凹陷性瘢痕疗效满意,对增生瘢痕疗效有限。是一种适合东方人痤疮瘢痕的安全,有效的治疗方法。

剪切波弹性成像技术对慢性肾脏病的诊断价值

目的分析剪切波弹性成像技术(SWE)对慢性肾脏病(CKD)的诊断价值。方法选择2022年9月至2023年7月新乡医学院第一附属医院收治的125例CKD患者为研究对象,依据病情分期将其分为CKD 1期组(n=22)、CKD 2期组(n=24)、CKD 3期组(n=26)、CKD 4期组(n=26)、CKD 5期组(n=27)。另选择同时期自愿参加本研究的55例健康志愿者作为对照组。应用彩色多普勒超声诊断仪检测各组受试者肾实质的剪切波速度(SWV)、肾实质像素强度、叶间动脉阻力指数(RI)及肾脏皮质部、髓质部、肾窦部杨氏模量值。采用受试者操作特征(ROC)曲线分析SWE对CKD的诊断价值。结果各分期组CKD患者右肾和左肾皮质SWV、髓质SWV均显著低于对照组,且整体趋势表现为随着病情加重逐渐降低(P<0.05);肾实质像素强度高于对照组,且整体趋势表现为随着病情加重逐渐升高(P<0.05)。各分期组CKD患者肾脏皮质部、髓质部杨氏模量值的平均值、最大值、最小值均显著高于对照组,且整体趋势表现为随着病情加重各数值逐渐升高(P<0.05)。各组受试者肾窦部杨氏模量值比较差异均无统计学意义(P>0.05)。ROC曲线结果显示,肾皮质部杨氏模量值的平均值、最大值、最小值、肾实质像素强度及SWV诊断CKD的曲线下面积分别为0.955、0.920、0.940、0.910、0.858,对CKD均有较佳的诊断价值。结论SWE可协助诊断CKD,且对于患者肾实质病变程度评估有一定参考价值。

Design,Analysis,and Optimization of a CMOS Active Pixel Sensor

A three-transistor active pixel sensor and its double sampling readout circuit implemented by a switch capacitor amplifier are designed. The circuit is embedded in a 64 × 64 pixel array CMOS image sensor and success-fully taped out with a Chartered 0.35μm process. The pixel pitch is 8μm × 8μm with a fill factor of 57%, the photo-sensitivity is 0.8V/（lux · s） ,and the dynamic range is 50dB. Theoretical analysis and test results indicate that as the process is scaled down, a smaller pixel pitch reduces the sensitivity. A deep junction n-well/p-substrate photodiode with a reasonable fill factor and high sensitivity are more appropriate for submicron processes.

Pixel激光治疗黄褐斑的疗效和安全性分析

目的:评估Pixel激光治疗黄褐斑的疗效及安全性。方法:采用Pixel激光治疗黄褐斑患者72例,3～4周治疗1次,3～5次为一个疗程,每次复诊由医生和患者共同评定疗效和安全性。结果:72例患者中,痊愈17例(23.61%),显效18例(25.0%),有效率48.61%。轻度组:痊愈率45.45%(15例),显效率36.36%(12例),有效率81.81%;重度组:痊愈率5.13%(2例),显效率15.38%(6例),有效率20.51%;两组比较有显著性差异。病程小于2年者,有效率68.42%,疗效高于病程大于2年者。21例患者术后出现轻度色素沉着,均于术后3个月消退。结论:Pixel激光治疗黄褐斑安全有效,病程短、颜色浅者疗效更佳。

Pixel Factory影像数据处理系统介绍与应用探讨

简单阐述Pixel Factory体系结构及其特点,结合航空、航天遥感影像数据处理项目重点分析该系统在海量遥感影像数据处理中所展现出的优势并针对存在的相关问题进行探讨。实践证明,该系统在传统正射影像制作、海量卫星影像数据处理方面具有明显算法优势,但DSM自动计算算法及框幅式航摄数据空中三角测量功能仍需增强。