The microstructure evolution during deformation enhanced transformation of undercooled austenite of a plain low carbon steel has been investigated by means of hot compression simulation experiment under various condit...The microstructure evolution during deformation enhanced transformation of undercooled austenite of a plain low carbon steel has been investigated by means of hot compression simulation experiment under various conditions of strain rate, deformation temperature and strain. The effect of austenite grain size on the strain enhanced ferrite transformation has been studied. The ferrite dynamic recrystallization involved in successive hot deformation has been explored.展开更多
Bipolar plates are a multifunctional component of PEMFC. Comparing with the machined graphite and stainless steels, the plain carbon steel is a very cheap commercial metal material. In this paper, the possibility of a...Bipolar plates are a multifunctional component of PEMFC. Comparing with the machined graphite and stainless steels, the plain carbon steel is a very cheap commercial metal material. In this paper, the possibility of applying the plain carbon steels in the bipolar plate for PEMFC was exploited. In order to improve the corrosion resistance of the low carbon steel in the PEMFCs′ environments, two surface modification processes was developed and then the electrochemical performances and interfacial contact resistance (ICR) of the surface modified plate of plain carbon steel were investigated. The results show that the surface modified steel plates have good corrosion resistance and relatively low contact resistance, and it may be a candidate material as bipolar plate of PEMFC.展开更多
The effects of cooling rate and coiling temperature on microstructure and mechanical properties of a plain carbon steel were investigated by combining metallography and tensile experiments. The results indicate that f...The effects of cooling rate and coiling temperature on microstructure and mechanical properties of a plain carbon steel were investigated by combining metallography and tensile experiments. The results indicate that ferrite grain size is refined and bainite transformation occurs to ensure high strength and elongation, as the cooling rate is quick enough. Yield strength and tensite strength improve with the decreased finish cooling temperature, but the elongation decreases too significantly to meet the requirements. Thus, the cooling rate must be quick enough, and the appropriate coiling temperature should be carefully selected to obtain refined ferrite and a small amount of bainite to improve the strength while the plasticity is also ensured. Under this condition, the Mn element concentration can be reduced to save cost or produce higher strength steel with same chemical composition.展开更多
1.IntroductionSo far there are few people who studythe relationship between the criticalhydrogen concentration and the stress forhvdrogen induced cracking (CCHIC)quantitatively.Several researchers have cal-culated the...1.IntroductionSo far there are few people who studythe relationship between the criticalhydrogen concentration and the stress forhvdrogen induced cracking (CCHIC)quantitatively.Several researchers have cal-culated the CCHIC of steels under no stressby means of H permeation method,but no展开更多
A model based on Avrami equation and Scheil's additivity rule was proposed to simulate the phase transformation in plain carbon steels during continuous cooling in hot strip mill. In this model, a wide range of co...A model based on Avrami equation and Scheil's additivity rule was proposed to simulate the phase transformation in plain carbon steels during continuous cooling in hot strip mill. In this model, a wide range of composition, cooling rate, primary austenite grain size and retained strain has been taken into account. It can be used to calculate the phase fraction transformed at different temperatures during continuous cooling. The phase equilibrium and transformation starting temperature can be determined by using Thermo-Calc and DICTRA. The simulated results containing the transformation at starting and finishing temperatures, Ae1, Ae3 and the maximum volume fraction for Q235B, were obtained. The calculated phase volume fractions are in good agreement with .the experimental results.展开更多
The program to predict the microstructure evolutions during hot strip rolling of C-M n steels has been developed in this paper, BV using this program, the microstructure changes with the processing parameters were ana...The program to predict the microstructure evolutions during hot strip rolling of C-M n steels has been developed in this paper, BV using this program, the microstructure changes with the processing parameters were analysed in detail. showing not only a good agreement of prediction with the measured values, but also entirely possibility to optimize hot strip rolling precess by computer simulation展开更多
Considering the specialities of the steel plate production, the TMCP study has been carried out with Gleeble 2000 tester to explore the possibility of fine grained ferrite in the low carbon steel plates with the chemi...Considering the specialities of the steel plate production, the TMCP study has been carried out with Gleeble 2000 tester to explore the possibility of fine grained ferrite in the low carbon steel plates with the chemical composition of C 0.13--0.18, Si 0.12-0.18, Mn 0.50-0. 65, P 0. 010-0. 025, and S 0. 005-0. 028. The plates with thickness of 8. 7 mm in which the ferrite grain size is smaller than 8μm have been produced by special de- formation process in the laboratory. Furthermore, the trial production of special plain carbon steel plates of 16-25 mm in thickness and 2 000- 2 800 mm in width with fine grained ferrite has been successfully carried out in the Shougang Steel Plate Rolling Plant. The ferrite grain size is 5.5-7μm in the surface layers and 9.5-15μm in the central layer respectively. The yield strength is 320- 360 MPa, tensile strength is 440-520 MPa and the elongation is 25%- 34 %. It is very important for the rolling plants to improve the low carbon steel plates＇ mechanical properties. The results show that the ferrite grains in the surface layer can be refined effectively by the appropriate rolling process, and the strength can be also increased.展开更多
The carbides/nitrides precipitates in ferrite grains, on grain boundaries and dislocations were investigated on a hot-rolled C-Mn strip （0.16wt%C-1.22wt%Mn-0.022wt%Ti） produced by the CSP （compact strip production...The carbides/nitrides precipitates in ferrite grains, on grain boundaries and dislocations were investigated on a hot-rolled C-Mn strip （0.16wt%C-1.22wt%Mn-0.022wt%Ti） produced by the CSP （compact strip production） technology using TEM and X-ray energy dispersive spectroscopy. The Pickering＇s equation for the contribution of precipitates to the yield stress was also discussed. It is shown that there are numerous fine and dispersive precipitates TiC in the ferrite grains, on the grain boundaries and dislocations. Also there are a small amount of coarser Ti（C, N） particles and TiC particles associated with MnS. Precipitation strengthening on steels produced by the CSP technology is significant.展开更多
A new thermomechanical process consisting of heavy cold rolling(HCR)and short-time heat treatment(STH)is developed to fabricate fine-grained martensite microstructure in a low-cost plain low-carbon steel.To achieve th...A new thermomechanical process consisting of heavy cold rolling(HCR)and short-time heat treatment(STH)is developed to fabricate fine-grained martensite microstructure in a low-cost plain low-carbon steel.To achieve the optimal mechanical properties after STH,three different ferrite-pearlite(F-P)dual-phase microstructures are prepared via hot rolling(HR),HR and austenitizing,and HR and HCR.The microstructure evolution and the comprehensive mechanical properties of the alloy during STH are then investigated.We find that the volume fractions of transformed martensite after STH increase with decreasing grain sizes of the pre-STH F-P dual phases.The rapid heating and short-time holding of STH promote grain nucleation and inhibit grain growth,resulting in microstructure refinement.The formation of martensites with different morphologies and different carbon concentrations in the HR and HCR+STH alloy is identified,owing to the inhomogeneous carbon distribution by STH.Tensile experiments demonstrate that STH greatly improves the comprehension mechanical properties of the alloy.Excellent mechanical properties,with a yield strength of 1224 MPa,a tensile strength of 1583 MPa,a uniform elongation of 4.0%and a total elongation of 7.3%are achieved in the HR and HCR+STH alloy.These excellent mechanical properties are principally attributed to the microstructure refinement and martensite formation induced by STH,with a yield strength improvement of 134%and a tensile strength improvement of 150%relative to the HR alloy.展开更多
基金Acknowledgements-Financial support of National Science and Technology Ministry to the research projectfundamental research of
文摘The microstructure evolution during deformation enhanced transformation of undercooled austenite of a plain low carbon steel has been investigated by means of hot compression simulation experiment under various conditions of strain rate, deformation temperature and strain. The effect of austenite grain size on the strain enhanced ferrite transformation has been studied. The ferrite dynamic recrystallization involved in successive hot deformation has been explored.
文摘Bipolar plates are a multifunctional component of PEMFC. Comparing with the machined graphite and stainless steels, the plain carbon steel is a very cheap commercial metal material. In this paper, the possibility of applying the plain carbon steels in the bipolar plate for PEMFC was exploited. In order to improve the corrosion resistance of the low carbon steel in the PEMFCs′ environments, two surface modification processes was developed and then the electrochemical performances and interfacial contact resistance (ICR) of the surface modified plate of plain carbon steel were investigated. The results show that the surface modified steel plates have good corrosion resistance and relatively low contact resistance, and it may be a candidate material as bipolar plate of PEMFC.
文摘The effects of cooling rate and coiling temperature on microstructure and mechanical properties of a plain carbon steel were investigated by combining metallography and tensile experiments. The results indicate that ferrite grain size is refined and bainite transformation occurs to ensure high strength and elongation, as the cooling rate is quick enough. Yield strength and tensite strength improve with the decreased finish cooling temperature, but the elongation decreases too significantly to meet the requirements. Thus, the cooling rate must be quick enough, and the appropriate coiling temperature should be carefully selected to obtain refined ferrite and a small amount of bainite to improve the strength while the plasticity is also ensured. Under this condition, the Mn element concentration can be reduced to save cost or produce higher strength steel with same chemical composition.
文摘1.IntroductionSo far there are few people who studythe relationship between the criticalhydrogen concentration and the stress forhvdrogen induced cracking (CCHIC)quantitatively.Several researchers have cal-culated the CCHIC of steels under no stressby means of H permeation method,but no
基金This work was financially supported by the National Key Foundational Research Project(grant No.G1998061512).
文摘A model based on Avrami equation and Scheil's additivity rule was proposed to simulate the phase transformation in plain carbon steels during continuous cooling in hot strip mill. In this model, a wide range of composition, cooling rate, primary austenite grain size and retained strain has been taken into account. It can be used to calculate the phase fraction transformed at different temperatures during continuous cooling. The phase equilibrium and transformation starting temperature can be determined by using Thermo-Calc and DICTRA. The simulated results containing the transformation at starting and finishing temperatures, Ae1, Ae3 and the maximum volume fraction for Q235B, were obtained. The calculated phase volume fractions are in good agreement with .the experimental results.
文摘The program to predict the microstructure evolutions during hot strip rolling of C-M n steels has been developed in this paper, BV using this program, the microstructure changes with the processing parameters were analysed in detail. showing not only a good agreement of prediction with the measured values, but also entirely possibility to optimize hot strip rolling precess by computer simulation
文摘Considering the specialities of the steel plate production, the TMCP study has been carried out with Gleeble 2000 tester to explore the possibility of fine grained ferrite in the low carbon steel plates with the chemical composition of C 0.13--0.18, Si 0.12-0.18, Mn 0.50-0. 65, P 0. 010-0. 025, and S 0. 005-0. 028. The plates with thickness of 8. 7 mm in which the ferrite grain size is smaller than 8μm have been produced by special de- formation process in the laboratory. Furthermore, the trial production of special plain carbon steel plates of 16-25 mm in thickness and 2 000- 2 800 mm in width with fine grained ferrite has been successfully carried out in the Shougang Steel Plate Rolling Plant. The ferrite grain size is 5.5-7μm in the surface layers and 9.5-15μm in the central layer respectively. The yield strength is 320- 360 MPa, tensile strength is 440-520 MPa and the elongation is 25%- 34 %. It is very important for the rolling plants to improve the low carbon steel plates＇ mechanical properties. The results show that the ferrite grains in the surface layer can be refined effectively by the appropriate rolling process, and the strength can be also increased.
基金This work was financially supported by the National High-Tech Research and Development Program of China(No.2001AA332020).
文摘The carbides/nitrides precipitates in ferrite grains, on grain boundaries and dislocations were investigated on a hot-rolled C-Mn strip （0.16wt%C-1.22wt%Mn-0.022wt%Ti） produced by the CSP （compact strip production） technology using TEM and X-ray energy dispersive spectroscopy. The Pickering＇s equation for the contribution of precipitates to the yield stress was also discussed. It is shown that there are numerous fine and dispersive precipitates TiC in the ferrite grains, on the grain boundaries and dislocations. Also there are a small amount of coarser Ti（C, N） particles and TiC particles associated with MnS. Precipitation strengthening on steels produced by the CSP technology is significant.
基金funded by the National Natural Science Foundation of China(No.52071212).
文摘A new thermomechanical process consisting of heavy cold rolling(HCR)and short-time heat treatment(STH)is developed to fabricate fine-grained martensite microstructure in a low-cost plain low-carbon steel.To achieve the optimal mechanical properties after STH,three different ferrite-pearlite(F-P)dual-phase microstructures are prepared via hot rolling(HR),HR and austenitizing,and HR and HCR.The microstructure evolution and the comprehensive mechanical properties of the alloy during STH are then investigated.We find that the volume fractions of transformed martensite after STH increase with decreasing grain sizes of the pre-STH F-P dual phases.The rapid heating and short-time holding of STH promote grain nucleation and inhibit grain growth,resulting in microstructure refinement.The formation of martensites with different morphologies and different carbon concentrations in the HR and HCR+STH alloy is identified,owing to the inhomogeneous carbon distribution by STH.Tensile experiments demonstrate that STH greatly improves the comprehension mechanical properties of the alloy.Excellent mechanical properties,with a yield strength of 1224 MPa,a tensile strength of 1583 MPa,a uniform elongation of 4.0%and a total elongation of 7.3%are achieved in the HR and HCR+STH alloy.These excellent mechanical properties are principally attributed to the microstructure refinement and martensite formation induced by STH,with a yield strength improvement of 134%and a tensile strength improvement of 150%relative to the HR alloy.
