In this work, a set of GTN （Gurson-Tvergaard-Needleman） parameters of the Alloy52M dissimilar metal welded joint （DMWJ） have been calibrated, and a micromechanical analysis of in-plane constraint effects on the lo...In this work, a set of GTN （Gurson-Tvergaard-Needleman） parameters of the Alloy52M dissimilar metal welded joint （DMWJ） have been calibrated, and a micromechanical analysis of in-plane constraint effects on the local fracture behavior of two cracks, which located in the weakest regions of the DMWJ, has been investigated by the local approach based on the GTN damage model. The results show that the partition of the material and the variation of the q2 parameter make the J-resistance curves obtained by numerical simulations close to the experimental values. The numerical J-resistance curves and crack growth paths are consistent with the experiment results, which show that the GTN damage model can incorporate the in-plane constraint effect. Furthermore, after the stress, strain and damage fields at the crack tip during the crack propagation process have been calculated, and the change of the J-resistance curves, crack growth paths and fracture mechanism with in-plane constraint have been analyzed.展开更多
Plane strain elastic-plastic finite element analyses are used tostudy the stress, strain fields around a straight crack in powerhardening plastic material. Center crack panel (CCP), single edgecrack panel (SECP) and d...Plane strain elastic-plastic finite element analyses are used tostudy the stress, strain fields around a straight crack in powerhardening plastic material. Center crack panel (CCP), single edgecrack panel (SECP) and double edge crack panel (DECP) tensionspecimens are analyzed with various crack lengths. Two localconstraint parameters, i.e. in-plane stress ratio T_x andout-of-plane constraint T_z are an- alyzed, which are defined astangential stress dividing normal (open) stress and out-of-planestress dividing the sum of tangential stress and normal stressrespectively.展开更多
In the present paper,three dimensional analyses of some general constraint parameters and fracture parameters near the crack tip of Mode I CT specimens in two different thicknesses are carried out by employing ADINA p...In the present paper,three dimensional analyses of some general constraint parameters and fracture parameters near the crack tip of Mode I CT specimens in two different thicknesses are carried out by employing ADINA program.The results reveal that the constraints along the thickness direction are obviously separated into two parts:the keeping similar high constraint field(Z_(1))and rapid reducing constraints one(Z_(2)).The two fields are experimentally confiremed to correspond to the smooth region and the shear lip on the fracture face respectively.So the three dimensional stress structure of Mode I specimens can be derived through discussing the two fields respectively.The distribution of the Crack Tip Opening Displacement(CTOD)along the thickness direction and the three dimensional distribution of the void growth ratio(V_(g))near the crack tip are also obtained.The two fracture parameters are in similar trends along the thickness direction,and both of them can reflect the effect of thickness and that of the loading level to a certain degree.展开更多
The Green function method （GFM） is utilized to analyze the in-plane forced vibration of curved pipe conveying fluid, where the randomicity and distribution of the external excitation and the added mass and damping r...The Green function method （GFM） is utilized to analyze the in-plane forced vibration of curved pipe conveying fluid, where the randomicity and distribution of the external excitation and the added mass and damping ratio are considered. The Laplace transform is used, and the Green functions with various boundary conditions are obtained subsequently. Numerical calculations are performed to validate the present solutions, and the effects of some key parameters on both tangential and radial displacements are further investigated. The forced vibration problems with linear and nonlinear motion constraints are also discussed briefly. The method can be radiated to study other forms of forced vibration problems related with pipes or more extensive issues.展开更多
We describe a new active-set, cutting-plane Constraint Optimal Selection Technique (COST) for solving general linear programming problems. We describe strategies to bound the initial problem and simultaneously add mul...We describe a new active-set, cutting-plane Constraint Optimal Selection Technique (COST) for solving general linear programming problems. We describe strategies to bound the initial problem and simultaneously add multiple constraints. We give an interpretation of the new COST’s selection rule, which considers both the depth of constraints as well as their angles from the objective function. We provide computational comparisons of the COST with existing linear programming algorithms, including other COSTs in the literature, for some large-scale problems. Finally, we discuss conclusions and future research.展开更多
A new criterion of degree of freedom for planar mechanism was presented. Compared with Gruebler's equation, this criterion possesses some characteristics. On one hand, this equation needs no modifying to the compl...A new criterion of degree of freedom for planar mechanism was presented. Compared with Gruebler's equation, this criterion possesses some characteristics. On one hand, this equation needs no modifying to the complex hinges, degrees of local freedom, and the case of mechanism with all sliding pairs. On the other hand, synthesing the concepts of substitution higher pair for kinematically equivalent lower pair, DOF determination and evolution. which benefits the students in learning. Hence, the authors suggest the formula be recommended, since its briefness, easiness to grasp.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.51605292)the Natural Science Foundation of Shanghai(Grant No.15ZR1429000)the Youth Foundation of Shanghai(Grant No.ZZslg15013)
文摘In this work, a set of GTN （Gurson-Tvergaard-Needleman） parameters of the Alloy52M dissimilar metal welded joint （DMWJ） have been calibrated, and a micromechanical analysis of in-plane constraint effects on the local fracture behavior of two cracks, which located in the weakest regions of the DMWJ, has been investigated by the local approach based on the GTN damage model. The results show that the partition of the material and the variation of the q2 parameter make the J-resistance curves obtained by numerical simulations close to the experimental values. The numerical J-resistance curves and crack growth paths are consistent with the experiment results, which show that the GTN damage model can incorporate the in-plane constraint effect. Furthermore, after the stress, strain and damage fields at the crack tip during the crack propagation process have been calculated, and the change of the J-resistance curves, crack growth paths and fracture mechanism with in-plane constraint have been analyzed.
基金the National Foundation of Distinguished Young Scientists of China(No.59625510)
文摘Plane strain elastic-plastic finite element analyses are used tostudy the stress, strain fields around a straight crack in powerhardening plastic material. Center crack panel (CCP), single edgecrack panel (SECP) and double edge crack panel (DECP) tensionspecimens are analyzed with various crack lengths. Two localconstraint parameters, i.e. in-plane stress ratio T_x andout-of-plane constraint T_z are an- alyzed, which are defined astangential stress dividing normal (open) stress and out-of-planestress dividing the sum of tangential stress and normal stressrespectively.
文摘In the present paper,three dimensional analyses of some general constraint parameters and fracture parameters near the crack tip of Mode I CT specimens in two different thicknesses are carried out by employing ADINA program.The results reveal that the constraints along the thickness direction are obviously separated into two parts:the keeping similar high constraint field(Z_(1))and rapid reducing constraints one(Z_(2)).The two fields are experimentally confiremed to correspond to the smooth region and the shear lip on the fracture face respectively.So the three dimensional stress structure of Mode I specimens can be derived through discussing the two fields respectively.The distribution of the Crack Tip Opening Displacement(CTOD)along the thickness direction and the three dimensional distribution of the void growth ratio(V_(g))near the crack tip are also obtained.The two fracture parameters are in similar trends along the thickness direction,and both of them can reflect the effect of thickness and that of the loading level to a certain degree.
基金Project supported by the National Science and Technology Major Project(NMP)of China(No.2013ZX04011-011)
文摘The Green function method （GFM） is utilized to analyze the in-plane forced vibration of curved pipe conveying fluid, where the randomicity and distribution of the external excitation and the added mass and damping ratio are considered. The Laplace transform is used, and the Green functions with various boundary conditions are obtained subsequently. Numerical calculations are performed to validate the present solutions, and the effects of some key parameters on both tangential and radial displacements are further investigated. The forced vibration problems with linear and nonlinear motion constraints are also discussed briefly. The method can be radiated to study other forms of forced vibration problems related with pipes or more extensive issues.
文摘We describe a new active-set, cutting-plane Constraint Optimal Selection Technique (COST) for solving general linear programming problems. We describe strategies to bound the initial problem and simultaneously add multiple constraints. We give an interpretation of the new COST’s selection rule, which considers both the depth of constraints as well as their angles from the objective function. We provide computational comparisons of the COST with existing linear programming algorithms, including other COSTs in the literature, for some large-scale problems. Finally, we discuss conclusions and future research.
文摘A new criterion of degree of freedom for planar mechanism was presented. Compared with Gruebler's equation, this criterion possesses some characteristics. On one hand, this equation needs no modifying to the complex hinges, degrees of local freedom, and the case of mechanism with all sliding pairs. On the other hand, synthesing the concepts of substitution higher pair for kinematically equivalent lower pair, DOF determination and evolution. which benefits the students in learning. Hence, the authors suggest the formula be recommended, since its briefness, easiness to grasp.
