Nano-size aluminum nitride （A1N） powders have been successfully synthesized with a high efficiency method through annealing from milling assisted by discharge plasma （p-milling） alumina （Al2O3） precursors. The c...Nano-size aluminum nitride （A1N） powders have been successfully synthesized with a high efficiency method through annealing from milling assisted by discharge plasma （p-milling） alumina （Al2O3） precursors. The characterization of the p-milling Al2O3 powders and the synthesized AlN are investigated. Compared to conventional ball milling （c-milling）, it can be found that the precursors by p-milling have a finer grain size with a higher specific surface area, which lead to a faster reaction efficiency and higher conversion to A1N at lower temperatures. The activation energy of p-milling Al2O3 is found to be 371.5 kJ/mol, a value that is much less than the reported value of the unmilled and the conventional milled Al2O3. Meanwhile, the synthesized AlN powders have unique features, such as an irregular lamp-like morphology with uniform particle distribution and fine average particle size. The results are attributed to the unique synergistic effect of p-milling, which is the effect of deformation, fracture, and cold welding of Al2O3 powders resulting from ball milling, that will be enhanced due to the introduction of discharge plasma.展开更多
Based on the results of plasma experiments and research work done by Dawson and Jones, Trubnikov, Endean, and other researchers, three requirements for producing and maintaining plasma ball lightning have been found: ...Based on the results of plasma experiments and research work done by Dawson and Jones, Trubnikov, Endean, and other researchers, three requirements for producing and maintaining plasma ball lightning have been found: 1) rotation of plasma, 2) the density of charged particles nc > 3.15 × 10-10ω2,3) a stable confinement of plasma. In this model, the energy density of ball lightning ranged from 10-2 J / cm3 to 104 J/ cm3, the formation, shape, stability, energy, maintaining processes and other properties of ball lightning were explained reasonably.展开更多
A 92WC-8Co powder mixture with 33 nm WC grains was prepared by strengthening ball milling and was then sintered by spark plasma sintering （SPS） at 1000-1200℃ for 5-18 rain under 10-25 kN, respectively. Movement of ...A 92WC-8Co powder mixture with 33 nm WC grains was prepared by strengthening ball milling and was then sintered by spark plasma sintering （SPS） at 1000-1200℃ for 5-18 rain under 10-25 kN, respectively. Movement of the position of low punch shown shrinkage of the sintered body began above 800℃. The shrinkage slowly rose as the temperature rose from 800 to 1000℃ and then quickly rose at above 1000℃ and then gradually rose at above 1150℃. The densities of the samples increased with an increase in sintering temperature, rapidly below 1100℃, and then gradually above 1100℃. WC grains grow gradually with increasing sintering temperature. The powder was sintered to near full density at 1100℃ for 5 rain under 10 kN. The best result of the sample with 275 nm WC grains and no pores was obtained at 1150℃ under 10 kN for 5 rain. The research found the graphite die had a function of carburization, which could compensate the sintered body for the lack of carbon, and had the normal microstructure.展开更多
Ultrafine grain WC alloys were prepared by high energy ball milling and subsequent spark plasma sintering from elemental mixed powders of nominal composition of WC-6Co-1.5Al(%, mass fraction). The influences of spark ...Ultrafine grain WC alloys were prepared by high energy ball milling and subsequent spark plasma sintering from elemental mixed powders of nominal composition of WC-6Co-1.5Al(%, mass fraction). The influences of spark plasma sintering parameters on the density, hardness, bend strength and microstructure of sintered WC alloys were also investigated. The results show that there existed a proper time combination of pulse current and constant current employed for sintering.When the peak, base, frequency and occupational ratio of pulse current, constant current, total sintering time and sintering pressure were chosen as 3000 A, 360 A, 50 Hz, 50%, 1500 A, 6 min and 30 MPa, respectively, the optimal sintering was a combination application of 1min pulse-current and subsequent 5 min constant-current. The density, hardness and bend strength of the as sintered alloys could get up to 14.224 g/cm^3, HRA94 and 1660 MPa, respectively, and the average grain size of WC was only about 500 nm.展开更多
In this study, nanostructured Fe powders were synthesized following 10 hours of high-energy ball milling with a superimposed dielectric barrier discharge plasma （DBDP）. The mean size of the milled powder was approxi...In this study, nanostructured Fe powders were synthesized following 10 hours of high-energy ball milling with a superimposed dielectric barrier discharge plasma （DBDP）. The mean size of the milled powder was approximately 100 nm with an average grain size of 16.2 nm. The influence of DBDP on the underlying grain refinement mechanisms during ball milling was investigated by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, X-ray diffraction （XRD） and BET methods. Our results show that the Fe particles displayed an extraordinary plasticity during the early milling stages under the action of DBDP, and that the plastic deformation experienced by the Fe particles during this stage was more severe than that present in normal milling. A high concentration of spherical Fe particles, approximately 50-100 nm in diameter, was documented via TEM. We propose that these spherical particles were generated via high temperature disintegration as a result of DBDP electron bombardment during ball milling. Our results suggest that it may be possible to significantly refine metallic powders during milling via the superimposition of DBDP.展开更多
基金supported by National Natural Science Foundation of China(No.51177008)
文摘Nano-size aluminum nitride （A1N） powders have been successfully synthesized with a high efficiency method through annealing from milling assisted by discharge plasma （p-milling） alumina （Al2O3） precursors. The characterization of the p-milling Al2O3 powders and the synthesized AlN are investigated. Compared to conventional ball milling （c-milling）, it can be found that the precursors by p-milling have a finer grain size with a higher specific surface area, which lead to a faster reaction efficiency and higher conversion to A1N at lower temperatures. The activation energy of p-milling Al2O3 is found to be 371.5 kJ/mol, a value that is much less than the reported value of the unmilled and the conventional milled Al2O3. Meanwhile, the synthesized AlN powders have unique features, such as an irregular lamp-like morphology with uniform particle distribution and fine average particle size. The results are attributed to the unique synergistic effect of p-milling, which is the effect of deformation, fracture, and cold welding of Al2O3 powders resulting from ball milling, that will be enhanced due to the introduction of discharge plasma.
文摘Based on the results of plasma experiments and research work done by Dawson and Jones, Trubnikov, Endean, and other researchers, three requirements for producing and maintaining plasma ball lightning have been found: 1) rotation of plasma, 2) the density of charged particles nc > 3.15 × 10-10ω2,3) a stable confinement of plasma. In this model, the energy density of ball lightning ranged from 10-2 J / cm3 to 104 J/ cm3, the formation, shape, stability, energy, maintaining processes and other properties of ball lightning were explained reasonably.
文摘A 92WC-8Co powder mixture with 33 nm WC grains was prepared by strengthening ball milling and was then sintered by spark plasma sintering （SPS） at 1000-1200℃ for 5-18 rain under 10-25 kN, respectively. Movement of the position of low punch shown shrinkage of the sintered body began above 800℃. The shrinkage slowly rose as the temperature rose from 800 to 1000℃ and then quickly rose at above 1000℃ and then gradually rose at above 1150℃. The densities of the samples increased with an increase in sintering temperature, rapidly below 1100℃, and then gradually above 1100℃. WC grains grow gradually with increasing sintering temperature. The powder was sintered to near full density at 1100℃ for 5 rain under 10 kN. The best result of the sample with 275 nm WC grains and no pores was obtained at 1150℃ under 10 kN for 5 rain. The research found the graphite die had a function of carburization, which could compensate the sintered body for the lack of carbon, and had the normal microstructure.
文摘Ultrafine grain WC alloys were prepared by high energy ball milling and subsequent spark plasma sintering from elemental mixed powders of nominal composition of WC-6Co-1.5Al(%, mass fraction). The influences of spark plasma sintering parameters on the density, hardness, bend strength and microstructure of sintered WC alloys were also investigated. The results show that there existed a proper time combination of pulse current and constant current employed for sintering.When the peak, base, frequency and occupational ratio of pulse current, constant current, total sintering time and sintering pressure were chosen as 3000 A, 360 A, 50 Hz, 50%, 1500 A, 6 min and 30 MPa, respectively, the optimal sintering was a combination application of 1min pulse-current and subsequent 5 min constant-current. The density, hardness and bend strength of the as sintered alloys could get up to 14.224 g/cm^3, HRA94 and 1660 MPa, respectively, and the average grain size of WC was only about 500 nm.
基金supported by the National Natural Science Foundation of China (No.51177008)Natural Science Fundation of Fujian Province(No. 2012J01228)+1 种基金the Program for New Century Excellent Talents in Fujian Province University (No. NCETFJ–Z80136)Fujian Provincial Department of Science & Technology (Nos. 2011J01324 and JK2010030)
文摘In this study, nanostructured Fe powders were synthesized following 10 hours of high-energy ball milling with a superimposed dielectric barrier discharge plasma （DBDP）. The mean size of the milled powder was approximately 100 nm with an average grain size of 16.2 nm. The influence of DBDP on the underlying grain refinement mechanisms during ball milling was investigated by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, X-ray diffraction （XRD） and BET methods. Our results show that the Fe particles displayed an extraordinary plasticity during the early milling stages under the action of DBDP, and that the plastic deformation experienced by the Fe particles during this stage was more severe than that present in normal milling. A high concentration of spherical Fe particles, approximately 50-100 nm in diameter, was documented via TEM. We propose that these spherical particles were generated via high temperature disintegration as a result of DBDP electron bombardment during ball milling. Our results suggest that it may be possible to significantly refine metallic powders during milling via the superimposition of DBDP.
