Enhancing corrosion resistance of plasma electrolytic oxidation coatings on AM50 Mg alloy by inhibitor containing Ba(NO_(3))_(2) solutions

To enhance the long-term corrosion resistance of the plasma electrolytic oxidation(PEO)coating on the magnesium(Mg)alloy,an inorganic salt combined with corrosion inhibitors was used for posttreatment of the coating.In this study,the corrosion performance of PEO-coated AM50 Mg was significantly improved by loading sodium lauryl sulfonate(SDS)and sodium dodecyl benzene sulf-onate into Ba(NO_(3))_(2) post-sealing solutions.Scanning electron microscopy,X-ray photoelectron spectroscopy,X-ray diffraction,Fourier transform infrared spectrometer,and ultraviolet-visible analyses showed that the inhibitors enhanced the incorporation of BaO_(2) into PEO coatings.Electrochemical impedance showed that post-sealing in Ba(NO_(3))_(2)/SDS treatment enhanced corrosion resistance by three orders of magnitude.The total impedance value remained at 926Ω·cm^(2)after immersing in a 0.5wt%NaCl solution for 768 h.A salt spray test for 40 days did not show any obvious region of corrosion,proving excellent post-sealing by Ba(NO_(3))_(2)/SDS treatment.The corrosion resistance of the coating was enhanced through the synergistic effect of BaO2 pore sealing and SDS adsorption.

NaF assisted preparation and the improved corrosion resistance of high content ZnO doped plasma electrolytic oxidation coating on AZ31B alloy

In the present research,the NaF assisted plasma electrolytic oxidation(PEO)is designed to fabricate the high-content ZnO nanoparti-cles doped coating on AZ31B alloy.The microstructure,phase constituents and corrosion behavior of the PEO coatings are investigated systematically.The results reveal that the introduction of NaF promotes the formation of MgF2 nanophases in the passivation layer on Mg alloy,decreasing the breakdown voltage and discharge voltage.As a result,the continuous arcing caused by high discharge voltage is alleviated.With the increasing of NaF content,the Zn content in the PEO coating is enhanced and the pore size in the coating is decreased correspondingly.Due to the high-content ZnO doping,the PEO coating protected AZ31B alloy demonstrates the better corrosion resistance.Compared with the bare AZ31B alloy,the high-content ZnO doped PEO coated sample shows an increased corrosion potential from-1.465 V to-1.008 V,a decreased corrosion current density from 3.043×10^(-5) A·cm^(-2) to 3.960×10^(-8) A·cm^(-2) and an increased charge transfer resistance from 1.213×10^(2) ohm·cm^(2) to 2.598×10^(5) ohm·cm^(2).Besides,the high-content ZnO doped PEO coated sample also has the excellent corrosion resistance in salt solution,exhibiting no obvious corrosion after more than 2000 h neutral salt spraying and 28 days’immersion testing.The improved corrosion resistance can be ascribed to the relative uniform distribution of ZnO in PEO coating which can transform to Zn(OH)2 and form a continuous protective layer along the corrosion interface.

Formation process of composite plasma electrolytic oxidation coating containing zirconium oxides on AM50 magnesium alloy

The formation processes of a composite ceramic coating on AM50 magnesium alloy prepared by plasma electrolytic oxidation （PEO） in a K 2 ZrF 6 electrolyte solution were studied by scanning electron microscope （SEM） and energy dispersive X-ray spectroscope （EDX）. Electrochemical impedance spectroscopy （EIS） tests were used to study the variation of the corrosion resistance of the coating during the PEO treatment. The results show that the coating formed on Mg alloy is mainly composed of MgO and MgF 2 when the applied voltage is lower than the sparking voltage, and zirconium oxides start to be deposited on Mg substrate after the potential exceeding the sparking voltage. The corrosion resistance of the coating increases with increasing the applied voltage.

Effects of current density on microstructure and properties of plasma electrolytic oxidation ceramic coatings formed on 6063 aluminum alloy

Plasma electrolytic oxidation (PEO) ceramic coatings were fabricated in a silicate-based electrolyte with the addition of potassium fluorozirconate (K2ZrF6) on 6063 aluminum alloy, and the effects of current density on microstructure and properties of the PEO coatings were studied. It was found that pore density of the coatings decreased with increasing the current density. The tribological and hardness tests suggested that the ceramic coating produced under the current density of 15 A/dm2showed the best mechanical property, which matched well with the phase analysis. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curves proved that the coating obtained under 15 A/dm2 displayed the best anti-corrosion property, which was directly connected with morphologies of coatings.

Plasma electrolytic oxidation of zircaloy-4 alloy with DC regime and properties of coatings

The plasma electrolytic oxidation（PEO） coatings on zircaloy？4 alloy were prepared in silicate,phosphate and pyrophosphate electrolyte systems or their combination by DC current regime.The proper processing parameters were determined and the coatings were evaluated by electrochemistry technique,micro-hardness,SEM and XRD.The results show that the coating prepared in pure silicate system is uneven and after the addition of phosphate solution,the homogeneity of the coating is still poor.The coating prepared in pure pyrophosphate electrolyte system is homogeneous,but its hardness value is low.After the addition of silicate into the pyrophosphate electrolytic system,both the uniformity and hardness of the coating are improved.The XRD results show that the phase compositions are m-ZrO2 and t-ZrO2,the addition of silicate is beneficial to the formation of t-ZrO2.The results of polarization curves show that the coatings prepared in pyrophosphate and the mixture of pyrophosphate and silicate have better corrosion resistance.

Wear and corrosion resistant coatings on surface of cast A356 aluminum alloy by plasma electrolytic oxidation in moderately concentrated aluminate electrolytes

Plasma electrolytic oxidation of a cast A356 aluminum alloy was carried out in aluminate electrolytes to develop wear and corrosion resistant coatings. Different concentrations of 2, 16 and 24 g/L NaAlO2 solutions and a silicate electrolyte （for comparison） were employed for the investigation. Wear performance and corrosion resistance of the coatings were evaluated by WC （tungsten carbide） ball-on-flat dry sliding tests and electrochemical methods, respectively. The results show that the coating formed for a short duration of 480 s in 24 g/L NaAlO2 solution generated the best protection. The coating sustained 30 N load for sliding time of 1800 s, showing very low wear rate of -4.5×10^-7 mm3/（N· m）. A low corrosion current density of -8.81×10^-9 A/cm2 was also recorded. Despite low α-Al2O3 content of the coating, the compact and nearly single layer nature of the coating guaranteed the excellent performances.

Plasma electrolytic oxidation of magnesium and its alloys:Mechanism,properties and applications

Plasma Electrolyte Oxidation(PEO)process has increasingly been employed to improve magnesium surface properties by fabrication of an MgO-based coating.Originating from conventional anodizing procedures,this high-voltage process produces an adhesive ceramic film on the surface.The present article provides a comprehensive review around mechanisms of PEO coatings fabrication and their different properties.Due to complexity of PEO coatings formation,a complete explanation regarding fabrication mechanisms of PEO coatings has not yet been proposed;however,the most important advancements in the field of fabrication mechanisms of PEO coatings were gathered in this work.Mechanisms of PEO coatings fabrication on magnesium were reviewed considering voltage–time plots,optical spectrometry,acoustic emission spectrometry and electronic properties of the ceramic film.Afterwards,the coatings properties,affecting parameters and improvement strategies were discussed.In addition,corrosion resistance of coatings,important factors in corrosion resistance and methods for corrosion resistance improvement were considered.Tribological properties(important factors and improvement methods)of coatings were also studied.Since magnesium and its alloys are broadly used in biological applications,the biological properties of PEO coatings,important factors in their biological performance and existing methods for improvement of coatings were explained.Addition of ceramic based nanoparticles and formation of nanocomposite coatings may considerably influence properties of plasma electrolyte oxidation coatings.Nanocomposite coatings properties and nanoparticles adsorption mechanisms were included in a separate sector.Another method to improve coatings properties is formation of hybrid coatings on PEO coatings which was discussed in the end.

Growth behaviour of low-energy plasma electrolytic oxidation coatings on a magnesium alloy

Plasma electrolytic oxidation(PEO),a promising surface treatment method to improve the corrosion and wear resistance of magnesium and its alloys,operates at high voltages,resulting in a relatively high energy cost.To make the PEO process more economically viable,its energy efficiency needs to be improved.This study investigates the growth behaviour and microstructural characteristics of low-energy PEO coatings on an AM50 magnesium alloy in a concentrated electrolyte containing sodium tetraborate.The surface morphology of the coatings was different from typical PEO coating morphologies and a large voltage oscillation was observed during treatment.Using different characterisation techniques,and based on a micro-discharge model,a correlation was made between the voltage-time behaviour,microdischarge characteristics and the composition and microstructure of the coated samples.The results suggest electrolyte chemistry can somewhat control discharge behaviour,which plays an important role in PEO coating growth.

Effects of electrical parameters and their interactions on plasma electrolytic oxidation coatings on aluminum substrates

Based on orthogonal experiments,the effects of voltage,frequency,duty ratio and their interactions on the thickness and corrosion resistance of coatings prepared by plasma electrolytic oxidation(PEO)on aluminum in an alkaline silicate-containing electrolyte were investigated.The thicknesses of these coatings were obtained by measuring their cross-section using Image J software.Their corrosion resistances were evaluated in HCl and NaCl media through spot test and electrochemical test.The results show that the experimental design of this study is the key to investigate the interactions among these electrical parameters.Additionally,not only each independent factor,but also their interactions exhibit a remarkable influence on the coatings.The combination of high voltage,low frequency and large duty ratio significantly increases the coating thickness and content of the corrosion resistance phase,and thus improves the corrosion resistance of the coating in HNO3 medium.Conversely,the coating possessing the densest microstructure and best corrosion resistance in NaCl medium is obtained when low voltage and high frequency match with a small duty ratio.

Corrosion and wear resistance of AZ31 Mg alloy treated by duplex process of magnetron sputtering and plasma electrolytic oxidation

In order to improve the wear and corrosion resistance of AZ31 magnesium alloy,a magnetron-sputtered Al layer with a thickness of 11μm was firstly applied on the alloy,and then treated by plasma electrolytic oxidation(PEO)in an aluminate and silicate electrolytes,respectively.The performance of PEO coatings was investigated by dry sliding wear and electrochemical corrosion tests.The aluminate coating exhibits excellent wear resistance under both 10 and 20 N loads.The silicate coating only shows low wear rate under 10 N,but it was destroyed under 20 N.Corrosion tests show that the Al layer after magnetron sputtering treatment alone cannot afford good protection to the Mg substrate.However,the duplex layer of PEO/Al can significantly improve the corrosion resistance of AZ31 alloy.Electrochemical tests show that the aluminate and silicate coatings have corrosion current densities of-1.6×10^(-6) and-1.1×10^(-6) A/cm^(2),respectively,which are two orders lower than that of the un-coated AZ31 alloy.However,immersion tests and electrochemical impedance spectroscopy(EIS)show that the aluminate coating exhibits better long-term corrosion protection than silicate coating.

Hybrid electric discharge plasma technologies for water decontamination:a short review

Electric discharge plasma(EDP)can efficiently degrade aqueous pollutants by its in situ gen erated strong oxidative species(OH,0,H2O2.O.etc)“nd other physiochemical effects(UV irradiation,shockwaves,local high temperature,etc),but a high energy consumptions limit the application of EDP in water treatment.Some adsorbents,catalysts,and oxida nts have been employed for en hanci ng the degradation of pollutants by discharge plasma.These hybrid plasma technologies offer improved water treatment performance compared to dischai'ge plasma alone.This paper reviews the water decontamination performance and mechanisms of these hybrid plasma technologies,and some suggestions on future water treatment technologies based on discharge plasma are also proposed.

Preparation of micro/nano-structured ceramic coatings on Ti6Al4V alloy by plasma electrolytic oxidation process

In order to improve the osseointegration and antibacterial activity of titanium alloys,micro/nano-structured ceramic coatings doped with antibacterial element F were prepared by plasma electrolytic oxidation(PEO)process on Ti6Al4V alloy in NaF electrolyte.The influence of NaF concentration(0.15-0.50 mol/L)on the PEO process,microstructure,phase composition,corrosion resistance and thickness of the coatings was investigated using scanning/transmission electron microscopy,energy dispersive spectroscopy,atomic force microscopy,X-ray diffractometer,and potentiodynamic polarization.The results demonstrated that Ti6Al4V alloy had low PEO voltage(less than 200 V)in NaF electrolyte,which decreased further as the NaF concentration increased.A micro/nano-structured coating with 10-15μm pits and 200-800 nm pores was formed in NaF electrolyte;the morphology was different from the typical pancake structure obtained with other electrolytes.The coating formed in NaF electrolyte had low surface roughness and was thin(<4μm).The NaF concentration had a small effect on the phase transition from metastable anatase phase to stable rutile phase,but greatly affected the corrosion resistance.In general,as the NaF concentration increased,the surface roughness,phase(anatase and rutile)contents,corrosion resistance,and thickness of the coating first increased and then decreased,reaching the maximum values at 0.25 mol/L NaF.

Improving the wear resistance of plasma electrolytic oxidation(PEO)coatings applied on Mg and its alloys under the addition of nano-and micro-sized additives into the electrolytes:A review

As an efficient surface modification approach,the plasma electrolytic oxidation(PEO)technique can boost the capability of wear protection in Mg and its alloys by applying a hard and thick ceramic coating.In this procedure,more efficient protection can be acquired via adding additives(in the form of particle,powder,sheet,etc.)into solutions and producing composite coatings.These additives result in more efficient protection against wear via getting stuck in the cracks and pores of coatings and rising the thickness,hardness,and diminishing the porosity size and content.The efficiency of each additive can be changed owing to its intrinsic properties like melting point,size,participation type(reactive,partly reactive,or inert)and potential of zeta.In this review,the effects of distinct additives in nano-and micro-scale size on wear behavior of PEO coatings on Mg and its alloys is going to be reviewed.

Investigation of mutual effects among additives in electrolyte for plasma electrolytic oxidation on magnesium alloys

Plasma electrolytic oxidation(PEO)coatings were prepared on AZ91D magnesium alloys in alkaline silicate-based electrolyte with and without additives.The mutual effects among additives including TiC particles,dispersant polyethylene glycol 6000(PEG6000)and anionic surfactant sodium dodecyl sulfate(SDS)were studied based on orthogonal experiment.The content and distribution of TiC deposited in the coatings were measured by EPMA and EDS.The thicknesses,phase compositions,microstructures and corrosion resistances of the codlings were cAarnined by using TT260 eddy current tuickncss gage,XRD,SEM and clcctrochcniical test,respectively.The results show that the experiment design of this study is the key to study the mutual effects among these additives.Each additive and their interactions all remarkably influence TiC content and corrosion resistance of the coatings.Smaller size TiC is much easier to migrate towards the anode,and the interaction between PEG6000 and SDS both effectively prevents its agglomeration and increases the number of its negative surface charges,which further increase the migration rate and the deposited uniformity of TiC and make TiC have more opportunity to deposit in the discharge channel.Thus,when smaller size TiC,PEG6000 and SDS are all added into the electrolyte,they could improve the anti-corrosion property of the coating to the largest extent attributed to higher TiC content and the densest microstructure of the coating.

Wear and corrosion behavior of clay containing coating on AM 50 magnesium alloy produced by aluminate-based plasma electrolytic oxidation

This study aims to examine the effect of clay micro particles addition on the microstructure,wear and corrosion behavior of PEO coatings on AM 50 magnesium alloy.PEO coatings were prepared using an aluminate-based electrolyte with and without the presence of 5 g/L clay particles.The structure and composition of the coatings were evaluated using SEM,EDS and XRD.The wear investigations were conducted using a ball-on-disk tribometer at 2,5 and 10 N loads.The corrosion behavior of the coatings was examined using polarization and EIS tests in 0.5 wt.%NaCl.The results revealed that the addition of clay particles deteriorated the wear resistance of the coatings under the loads of 5 and 10 N.The SEM examinations of the worn surfaces indicated that a combination of adhesive and abrasive wear mechanisms was activated for the coating with clay particles.The poor wear performance of the clay-incorporated coating was related to its lower adhesion strength and higher roughness.The potentiodynamic polarization examinations revealed that the addition of clay particles slightly decreased the corrosion rate of the coatings.Corrosion resistance of the clay-containing coating was attributed to its compactness,as indicated by the results of EIS tests.

Effect of particles addition to solution of plasma electrolytic oxidation(PEO)on the properties of PEO coatings formed on magnesium and its alloys:A review

The plasma electrolytic oxidation(PEO)procedure is utilized in order to amend the surface properties of Mg and its alloys.This procedure creates a ceramic coating on the surface applying high-voltage.The presence of deep pores and porosities in the surface that affect the corrosion resistance of the coatings is one of the PEO procedure limitations.One of the useful methods to decrease porosities of coating and improve its final properties is changing electrolyte conditions based on the presence of micro-and nanoparticles.The present paper reviews the mechanisms of particle adsorption and composition in PEO thin films in addition to the effect of particle addition on the microstructure,composition and corrosion behavior of coatings that were applied on magnesium alloys.

Plasma electrolytic oxidation of AZ31 and AZ91 magnesium alloys:Comparison of coatings formation mechanism

The growth kinetics of PEO coatings on AZ31 and AZ91 magnesium alloys were studied and correlated with their structure,compositions(phase and elemental)and corrosion resistance.It was established that the coatings have a two-(outer and anodic)or three-layer structure(outer,inner and anodic)depending on the treatment time.Briefly,at short treatment time only an anodic layer and outer layer exists.Growth of the outer PEO layer takes place due to the micro discharges,which occur in vertical pores and voids with spherical cross-section.If the time is increasing,and electrolyte inside of the pores is heating-up,etching of the Mg substrate and oxide film becomes more dominant and horizontal pores in the interface between coating and metal are formed.In the pores new anodic layer will form and at this time the formation of the third inner layer starts.The growth of the inner layer happens via the anodic film as a result of micro discharge ignition in the horizontal pores,accompanied by formation of plasma in numerous micro-voids of this layer.The coatings formed on AZ91 alloy are denser,than those on AZ31,which is related to the difference in the rates of inner layer growth and dissolving of oxides which are located at the bottom of the horizontal pores.Because of the lower Al content,the AZ31 substrate itself and the also the oxide films are less stable and tend to dissolve at a higher rate compared to AZ91.Thus,it was demonstrated that a good corrosion resistance of the coatings was only obtained on AZ91 and if the average thickness of the coating is around 50μm,correlating with the formation of a sufficiently dense inner laye-Knowing this mechanism,a new two-step treatment was suggested,combining the standard PEO treatment with a subsequent PEO process in an electrolyte supporting the inner film formation.The concept was successfully applied and a further improved corrosion resistance was obtained compared to the single stage PEO process.This improvement of corrosion resistance was related to the better sealing of porosity and formation of a denser inner layer.

Characteristics of a multi-component MgO-based bioceramic coating synthesized in-situ by plasma electrolytic oxidation

Plasma electrolytic oxidation(PEO)has held great potential for the advancement of biodegradable implants,as it helps in developing porous bioceramic coatings on the surface of magnesium alloys.In this research work,MgO-based bioceramic coatings containing the Si,P,Ca,Na,and F elements have been successfully fabricated on an AZ31 magnesium alloy plate utilizing the PEO method.The characteristic current-voltage behavior of the samples during the process was surveyed in an electrolyte containing Ca(H_(2)PO_(4))_(2),Na_(2)SiO_(3)·9H_(2)O,Na_(3)PO_(4)·12H_(2)O,NaF,and KOH with a pH of 12.5 and electrical conductivity of 20 mS/cm^(-1).The results revealed that applying a voltage of 350-400 V(that is 50-100 V higher than the breakdown limit)could greatly facilitate the synthesis of a PEO ceramic coating with fewer defects and more uniform morphology.The resulting coating was a compositionally graded bioceramic layer with a thickness in the range of 3.5±0.4 to 6.0±0.7µm,comprising the above-mentioned elements as promising bioactive agents.The synthesized ceramic features were investigated in terms of the elemental distribution of components through the thickness,which indicated a gradual rise in the Si and P contents and,conversely,a decline in the F content towards the outer surface.The growth mechanism of the PEO coating has been discussed accordingly.

Micro and nano-enabled approaches to improve the performance of plasma electrolytic oxidation coated magnesium alloys

Magnesium(Mg)and its alloys have become a hot research topic in various industries owing to the specific physical and chemical properties.However,high corrosion rate is considered the key lifetime-limiting.Plasma electrolytic oxidation(PEO)method is a simple strategy to deposit an oxide layer on the surface of light metals such as magnesium alloys,to control corrosion rate and promote some other properties,depending on their performances.Nevertheless,their features including their micropore size,distribution,and interconnectivity,and microcracks have not been improved to an acceptable level to support long-term performances of the magnesium-based substrates.Studies have introduced micro/nano-enabled approaches to enhance various properties of PEO coatings such as corrosion resistance,tribological properties,self-healing ability,bioactivity,biocompatibility,antibacterial properties,or catalytic performances.These strategies consist of incorporating of micro and nanoparticles into the PEO layers to produce multi-functional surfaces or the formation of multi-layered coatings to cover the defects of PEO coatings.In this perspective,the present paper aims to overview various nano/micro-enabled strategies to promote the properties of PEO coatings on magnesium alloys.The main focus is given to the functional changes that occurred in response to the incorporation of various types of nano/micro-structures into the PEO coatings on magnesium alloys.

Optimization of plasma electrolyte oxidation process parameters for corrosion resistance of Mg alloy

Plasma electrolyte oxidation(PEO)is a surface treatment method with high dependency on the process parameters.This paper focuses on maximizing the corrosion resistance of PEO coatings applied on Mg-5Zn-0.4Ca(ZX504)alloy by optimizing the process parameiers.For this purpose,the Taguchi method based on LI8 orthogonal array with mixed level design was used for optimization and determining effective parameters.Main process factors including electrolyte concentration,current density,frequency and duty cycle were considered at different levels.The corrosion resistance,as the performance indicator,was obtained using electrochemical impedance spectroscopy technique.Surface characteristics were also evaluated using SEM(scanning electron microscopy),EDS(energy dispersive spectroscopy),profilometer and contact angle goniometer.The statistical analysis showed that the optimum condition could be obtained at a current density of 200 mA/cm^2,frequency of 500Hz and at a duty cycle of 30%,in an electrolyle containing 15 g/L NazPO·12H2O and 10g/L KF.