Construction and solution of strain model along thickness of aluminum alloy plate under plastic deformation

A thickness strain model of aluminium alloy plate under plastic deformation,based on thin plate assumption was proposed.It is found that when ratio of stress fractions is constant during in-plane loading,ratios of strain components under various loading conditions are linearly related and these points of ratios form a η-η line.Under these simple loadings,strains in thickness direction can be easily calculated by the η-η line equation without integral and differential work.When the plate is under more complicated loading conditions,the thickness can be computed by the proposed optimization and piecewise calculation model.Validation computations indicate that the relative error of the results of the presented model is less than 0.75% compared with the proven theories and FE simulation.Therefore,the developed model can be applied to engineering calculation,e.g.pre-stretching analysis of aerospace aluminium thick plate,with acceptable accuracy.

ANALYSIS ON THE MAGNETO-ELASTIC-PLASTIC BUCKLING/SNAPPING OF CANTILEVER RECTANGULAR FERROMAGNETIC PLATES

An analysis of buckling/snapping and bending behaviors of magneto-elastic-plastic interaction and coupling for cantilever rectangular soft ferromagnetic plates is presented. Based on the expression of magnetic force from the variational principle of ferromagnetic plates, the buckling and bending theory of thin plates, the Mises yield criterion and the increment theory for plastic deformation, we establish a numerical code to quantitatively simulate the behaviors of the nonlinearly multi-fields coupling problems by the finite element method. Along with the phenomena of buckling/snapping and bending, or the characteristic curve of deflection versus magnitude of applied magnetic fields being numerically displayed, the critical loads of buckling/snapping, and the influences of plastic deformation and the width of plate on these critical loads, the plastic regions expanding with the magnitude of applied magnetic field, as well as the evolvement of deflection configuration of the plate are numerically obtained in a case study.

Study on magneto-elastic-plastic deformation characteristics of ferromagnetic rectangular plate with simple supports

In this paper, the magnetic-elastic-plastic deformation behavior is studied for a ferromagnetic plate with simple supports. The perturbation formula of magnetic force is first derived based on the perturbation technique, and is then applied to the analysis of deformation characteristics with emphasis laid on the analyses of modes, symmetry of deformation and influences of incident angle of applied magnetic field on the plate deformation. The theoretical analyses offer explanations why the configuration offer- romagnetic rectangular plate with simple supports under an oblique magnetic field is in-wavy type along the x-direction, and why the largest deformation of the ferromagnetic plate occurs at the incident angle of 45°for the magnetic field. A numerical code based on the finite element method is developed to simulate quantitatively behaviors of the nonlinearly coupled multi-field problem. Some characteristic curves are plotted to illustrate the magneto--elastic-plastic deflections, and to reveal how the deflections can be influenced by the incident angle of applied magnetic field. The deformation characteristics obtained from the numerical simulations are found in good agreement with the theoretical analyses.

ANALYSIS OF THE LARGE DEFLECTION DYNAMIC PLASTIC RESPONSE OF SIMPLY-SUPPORTED CIRCULAR PLATES BY THE“MEMBRANE FACTOR METHOD”

Based on energy equilibrium,a new procedure called the Membrane Factor Method is devel- oped to analyze the dynamic plastic response of plates with deflections in the range where both bending mo- ments and membrane forces are important.The final deflection of a simply -supported circular rigid-plastic plate loaded by a uniformly distributed impulse is obtained.In comparison with other approximate solutions, the present results are found to be simpler and in better agreement with the corresponding experimental values reoorded by Florence.

Dynamic plastic response of clamped stiffened plates with large deflection

Study on the dynamic response, and especially the nonlinear dynamic response of stiffened plates is complicated by their discontinuity and inhomogeneity. The finite element method (FEM) and the finite strip method are usually adopted in their analysis. Although many useful conclusions have been obtained, the computational cost is enormous. Based on some assumptions, the dynamic plastic response of clamped stiffened plates with large deflections was theoretically investigated herein by a singly symmetric beam model. Firstly, the deflection conditions that a plastic string must satisfy were obtained by the linearized moment-axial force interaction curve for singly symmetric cross sections and the associated plastic flow rule. Secondly, the possible motion mechanisms of the beam under different load intensity were analysed in detail. For structures with plastic deformations, a simplified method was then given that the arbitrary impact load can be replaced equivalently by a rectangular pulse. Finally, to confirm the validity of the proposed method, the dynamic plastic response of a one-way stiffened plate with four fully clamped edges was calculated. The theoretical results were in good agreement with those of FEM. It indicates that the present calculation model is easy and feasible, and the equivalent substitution of load almost has no influence on the final deflection.

Effect of plastic deformation on diffusion-rolling bonding of steel sandwich plates

Diffusion bonding is one of the most important techniques for composite materials, while bonding temperature, holding time,and rolling reduction are the key parameters that affect the bonding strength of sandwich plates. To study the effect of plastic deformation on the bonding strength, laboratory experiments were carried on a Gleeble Thermal Simulator to imitate the diffusion-rolling bonding under different reductions for steel sandwich plates. The bonding strength and interlayer film thickness were measured, and the element diffusion was analyzed using line scanning. The relationship between the bonding strength and “diffused interlayer” thickness was investigated. It has been found that the bonding strength increases with reduction, whereas the interlayer film thickness decreases gradually as the reduction increases. The diffusion under plastic deformation is obviously enhanced in comparison with that of nil reduction. The mechanism of plastic deformation effect on the diffusion bonding and related models have been discussed.

Finite element analysis of elasto-plastic plate bending problems using transition rectangular plate elements

In this work, the finite element analysis of the elasto-plastic plate bending problems is carried out using transition rectangular plate elements. The shape functions of the transition plate elements are derived based on a practical rule. The transition plate elements are all quadrilateral and can be used to obtain efficient finite element models using minimum number of elements. The mesh convergence rates of the models including the transition elements are compared with the regular element models. To verify the developed elements, simple tests are demonstrated and various elasto-plastic problems are solved. Their results are compared with ANSYS results.

Elastic-plastic contact force history and response characteristics of circular plate subjected to impact by a projectile

A new elastic-plastic impact-contact model is proposed in this paper. By adopting the principle of minimum acceleration for elastic-plastic continue at finite deformation, and with the aid of finite difference method, the proposed model is applied in the problem of dynamic response of a clamped thin circular plate subjected to a projectile impact centrally. The impact force history and response characteristics of the target plate is studied in detail. The theoretical predictions of the impact force and plate deflection are in good agreements with those of LDA experimental data. Linear expressions of the maximum impact force/transverse deflection versus impact velocity are given on the basis of the theoretical results.

A NEW APPROACH OF PREDICTING BIFURCATION POINTS OF ELASTIC-PLASTIC BUCKLING OF PLATES AND SHELLS

The paper proposes a new approach of predicting the bifurcation points of elastic-plastic buckling of plates and shells,which is obtained from the natural combination of the Lyaponov's dy- namic criterion on stability and the modified adaptive Dynamic Relaxation(maDR)method developed recently by the authors.This new method can overcome the difficulties in the applications of the dy- namic criterion.Numerical results show that the theoretically predicted bifurcation points are in very good agreement with the corresponding experimental ones.The paper also provides a new means for further research on the plastic buckling paradox of plates and shells.

PERTURBATION ANALYSIS FOR MAGNETO-PLASTIC INSTABILITY OF FERROMAGNETIC BEAM-PLATES WITH GEOMETRIC IMPERFECTION

The magneto-plastic instability of a ferromagnetic beam-type plate with simple supports and small initial imperfection is analytically investigated in this paper for that the plastic deformation of the plate with a linear-strain hardening relation is considered when the plate is located in a strong uniformly distributed magnetic ?eld. After the distribution of magnetic ?elds related to the de?ected con?guration of plate is imaginably divided into two parts, i.e., one is related to the ?at plate and the other dependent on the perturbation of magnetic ?elds for which the plate con?guration changes from the ?at into the deformed state, the perturbation technique is employed to analyze the distribution of the perturbation magnetic ?elds in and out-of the magnetic medium of the ferromagnetic structure in a transverse magnetic ?eld, which leads to some analytical formulae/solutions for the magnetic ?elds and the resulting magnetic force exerted on the plate. Based on them, the magneto-plastic buckling and snapping of the plate in a transverse magnetic ?eld is discussed, and the critical magnetic ?eld is analytically formulated in terms of the parameters of geometry and material of the plate employed by solving the governing equation of the magneto-plastic plate in the applied magnetic ?eld. Further, the sensitivity of the initial imperfection on the magneto-plastic instability, expressed by an ampli?cation function, is obtained by solving the dynamic equation of de?ection of the plate after the inertial force in the transverse direction is taken into account. The results obtained show that the critical magnetic ?eld is sensitive to the plastic characteristic, e.g., hardening coe?cient, and the instability mode and de?ection of the plate are dependent on the geometrical imperfection as well.

Dynamic Plastic Response of Circular Plates Resting on Fluid with Finite Deformation

This paper concerns the dynamic plastic response of a circular plate resting on fluid subjected to a uniformly distributed rectangular load pulse with finite deformation. It is assumed that the fluid is incompressible and inviscous, and the plate is made of rigid-plastic material and simply supported along its edge. By using the method of the Hankel integral transformation, the nonuniform fluid resistance is derived as the plate and the fluid is coupled. Finally, an analytic solution for a circular plate under a medium load is obtained according to the equations of motion of the plate with finite deformation.

THE DYNAMIC PLASTIC BEHAVIOR OF A SIMPLY SUPPORTED CIRCULAR PLATE IN A DAMPING MEDIUM WITH FINITE-DEFLECTIONS

A theoretical analysis is presented for the dynamic plastic behavior of a simply supported rigid, perfectly plastic circular plate in damping medium with finite-deflections subjected to a rectangular pressure pulse. Analytical solutions of every moving stage under both medium and high loads are developed.

Elastic-plastic analytical solution for centric crack loaded by two pairs of point shear forces in finite plate

The near crack line analysis method was used to investigate a centric crack loaded by two pairs of point shear forces in a finite plate, and the analytical solution was obtained. The solution includes the unit normal vector of the elastic-plastic boundary near the crack line, the elastic-plastic stress fields near the crack line, the variations of the length of the plastic zone along the crack line with an external load, and the bearing capacity of a finite plate with a centric crack loaded by two pairs of point shear forces. The results are sufficiently precise near the crack line because the assumptions of small scale yielding theory have not been made and no other assumptions are taken.

LARGE DEFLECTION DYNAMIC PLASTIC RESPONSE OF CLAMPED SQUARE PLATES WITH STIEEENERS

The large deflection dynamic plastic response of fully clamped square plates with stiffeners under blast load is analyzed in detail in this paper. Various relevant motion patterns and criterions are presented. The formulas of maximum permanent deformation of the plates with stiffeners are derived. The results of calculation are compared with those of experiment in [3], with good agreement shown in most cases.

Elasto-plasticity and pore-pressure coupled analysis on the pullout behaviors of a plate anchor

A numerical method is proposed for the elasto-plasticity and pore-pressure coupled analysis on the pull- out behaviors of a plate anchor. The bounding-surface plasticity （BSP） model combined with Blot＇s consol- idation theory is employed to simulate the cyclic loading induced elasto-plastic deformation of the soil skeleton and the accompanying generation/dissipation of the excess pore water pressure. The suction force generated around the anchor due to the cyclic variation of the pore water pressure has much effect on the pullout capacity of the plate anchor. The calculated pullout capacity with the proposed method （i.e., the coupled analysis） gets lower than that with the conventional total stress analysis for the case of long-term sustained loading, but slightly higher for the case of short-term monotonic loading. The cyclic loading induced accumulation of pore water pressure may result in an obvious decrease of the stiffness of the soil-Plate anchor svstem.

THE ELASTO-PLASTIC STRAIN ANALYSIS OF NOTCHED PLATE UNDER CYCLIC LOADING—AN APPLICATION OF PLASTIC ANISOTROPIC HARDENING THEORY

In order to predict the life of engineering structures, it is necessary to investigate the strain distribution in notched members. In gineral, the Uauschinger Effect of materials under cyclic loading is not negligible, and so the anisolropic hardening model has been suggested. From the comparison between the calculated and experimental results in this paper, we can see that even the linear kinematic hardening model is quite suitable for strain analysis under cyclic loading.

Elasto-plastic postbuckling of damaged orthotropic plates

Based on the elasto-plastic mechanics and continuum damage theory, a yield criterion related to spherical tensor of stress is proposed to describe the mixed hardening of damaged orthotropic materials. Its dimensionless form is isomorphic with the Mises criterion for isotropic materials. Furthermore, the incremental elasto-plastic damage constitutive equations and damage evolution equations are established. Based on the classical nonlinear plate theory, the incremental nonlinear equilibrium equations of orthotropic thin plates considering damage effect are obtained, and solved with the finite difference and iteration methods. In the numerical examples, the effects of damage evolution and initial deflection on the elasto-plastic postbuckling of orthotropic plates are discussed in detail.

ANALYSIS OF THE LARGE DEFLECTION DYNAMIC RESPONSE OF RIGID-PLASTIC CIRCULAR PLATE RESTING ON FLUID

A study is presented for the large deflection dynamic response of rigid- plastic circular plate resting on potential fluid under a rectangular pressure pulse load. By virtue of Hankel integral transform technique,this interaction problem is reduced to a problem of dynamic plastic response of the plate in vacuum.The closed-form solutions are derived for both middle and high pressure loads by solving the equations of motion with the large deflection in the range where both bending moments and membrane forces are important.Some numerical results are given.

Three-Dimensional Thermo-Elastic-Plastic Finite Element Method Modeling for Predicting Weld-Induced Residual Stresses and Distortions in Steel Stiffened-Plate Structures

The objective of the present paper is to develop nonlinear finite element method models for predicting the weld-induced initial deflection and residual stress of plating in steel stiffened-plate structures. For this purpose, three-dimensional thermo-elastic-plastic finite element method computations are performed with varying plate thickness and weld bead length (leg length) in welded plate panels, the latter being associated with weld heat input. The finite element models are verified by a comparison with experimental database which was obtained by the authors in separate studies with full scale measurements. It is concluded that the nonlinear finite element method models developed in the present paper are very accurate in terms of predicting the weld-induced initial imperfections of steel stiffened plate structures. Details of the numerical computations together with test database are documented.

NEAR CRACK LINE ELASTIC-PLASTIC ANALYSIS FOR A FINITE PLATE LOADED BY TWO PAIRS OF ANTIPLANE POINT FORCES

In this paper, the improved near crack line analysis method proposed in Refs. [1] and [2] is used to investigate a center crack loaded by two pairs of antiplane point forces in a finite plate in an elastic-perfectly plastic solid. And the analytical solutions are obtained, that is elastic-plastic stress fields near the crack line and the law that the length of the plastic zone along the crack line is varied with an external loads tr,ld the bearing capacity of a finite plate with a center crack. The results of this paper are sufficiently precise near the crack line, because the assumptions of the small scale yielding theory have not been used and no other assumptions have been taken.