Indentation of elastically soft and plastically compressible solids

The effect of soft elasticity, i.e., a relatively small value of the ratio of Young＇s modulus to yield strength and plastic compressibility on the indentation of isotropically hardening elastic-viscoplastic solids is investigated. Calcu- lations are carried out for indentation of a perfectly sticking rigid sharp indenter into a cylinder modeling indentation of a half space. The material is characterized by a finite strain elastic-viscoplastic constitutive relation that allows for plas- tic as well as elastic compressibility. Both soft elasticity and plastic compressibility significantly reduce the ratio of nomi- nal indentation hardness to yield strength. A linear relation is found between the nominal indentation hardness and the log- arithm of the ratio of Young＇s modulus to yield strength, but with a different coefficient than reported in previous studies. The nominal indentation hardness decreases rapidly for small deviations from plastic incompressibility and then decreases rather slowly for values of the plastic Poisson＇s ratio less than 0.25. For both soft elasticity and plastic compressibility, the main reason for the lower values of indentation hardness is related to the reduction in the hydrostatic stress level in the material below the indenter.

Deformation of plastically compressible hardening-softening-hardening solids

Motivated by a model of the response of vertically aligned carbon nanotube （VACNT） pillars in uniaxial compression, we consider the deformation of a class of compressible elastic-viscoplastic solids with a hardeningsoftening-hardening variation of flow strength with plastic strain. In previous work （Hutchens et al. 2011） a constitutive relation was presented and used to model the response of VACNT pillars in axisymmetric compression. Subsequently, it was found that due to a programming error the constitutive relation presented in the paper （Hutchens et al. 2011） was not the one actually implemented. In particular, the plastic flow rule actually used did not satisfy plastic normality. Here, we present the constitutive formulation actually implemented in the previous work （Hutchens et al. 2011）. Dynamic, finite deformation, finite element calculations are carried out for uniaxial compression, uniaxial tension and for indentation of a ＂half-space＂ by a conical indenter tip. A sequential buckling-like deformation mode is found in compression when there is plastic non-normality and hardening- softening-hardening. The same material characterization gives rise to a Lfiders band-like deformation mode in ten- sion. When there is a deformation mode with a sharp front along mesh boundaries, the overall stress-strain response contains high frequency oscillations that are a mesh artifact. The responses of non-softening solids are also analyzed and their overall stress-strain behavior and deformation modes are compared with those of hardening-softening- hardening solids. We find that indentation with a sharp indenter tip gives a qualitatively equivalent response for hardening and hardening-softening-hardening solids.

Finite deformation analysis of crack tip fields in plastically compressible hardening–softening–hardening solids

Crack tip fields are calculated under plane strain small scale yielding conditions. The material is characterized by a finite strain elastic-viscoplastic constitutive relation with various hardening-softening-hardening hardness functions. Both plastically compressible and plastically incompressible solids are considered. Displacements corresponding to the isotropic linear elastic mode I crack field are prescribed on a remote boundary. The initial crack is taken to be a semi-circular notch and symmetry about the crack plane is imposed. Plastic compressibility is found to give an increased crack opening displacement for a given value of the applied loading. The plastic zone size and shape are found to depend on the plastic compressibility, but not much on whether material softening occurs near the crack tip. On the other hand, the near crack tip stress and deformation fields depend sensitively on whether or not material softening occurs. The combination of plastic compressibility and softening (or softening-hardening) has a particularly strong effect on the near crack tip stress and deformation fields.

Corrosion behavior of severely plastically deformed Mg and Mg alloys

Magnesium(Mg)alloys have several advantages,such as low density,high specific strength and biocompatibility.However,they also suffer weak points,such as high corrosion,low formability and easy ignition,which makes their applications limited.Many studies have been conducted to overcome these disadvantages and further improve the advantages of Mg alloys.Severe plastic deformation(SPD)is one of the most important techniques and has great effects on the microstructure refinement of Mg alloys and improvements in their strength and formability.Several researchers have studied the corrosion behavior of SPD-processed Mg alloys in recent decades.However,these studies have reported some controversial effects of SPD on the corrosion of Mg alloys,which makes the research roadmap ambiguous.Therefore,it is important to review the literature related to the corrosion properties of Mg alloys prepared by SPD and understand the mechanisms controlling their corrosion behavior.Effective grain refinement by SPD improves the corrosion properties of pure Mg and Mg alloys,but control of the processing conditions is a key factor for achieving this goal because texture,dislocation density,size and morphology of secondary phase also importantly affects the corrosion properties of Mg alloys.Reduced grain size in the fine grain-size range can decrease the corrosion rate due to the increased barrier effect of grain boundaries against corrosion and the formation of a stable passivation layer on the surface of fine grains.Basal texture reduces the corrosion rate because basal planes with the highest atomic planar density are more corrosion resistant than other planes.Increased dislocation density after SPD deteriorates the corrosion resistance of the interior grains and thus proper annealing after SPD is important.The fine and uniform distribution of secondary phase particles during SPD is important to minimize the micro-galvanic corrosion effect and retain small grains during annealing treatment for removing dislocations.

Revealing the role of pyramidal slip in the high ductility of Mg-Li alloy

The high ductility of Mg-Li alloy has been mainly ascribed to a high activity of pyramidal<c+a>slip to accommodate plastic strain.In the present study,however,a quantitative analysis reveals that Li-addition can only slightly stimulate the activation of pyramidal<c+a>slip under compression along the normal direction of a hot-rolled Mg-4.5 wt.%Li plate,with a relative activity of approximately 18%.Although the limited activity of pyramidal<c+a>slip alone cannot accommodate a large plastic strain,it effectively reduces the number of{10.11}−{10.12}double twins,which are believed to be favorable sites for crack initiation.The evidently reduced activity of double twins leads to a lower cracking tendency,and therefore improves ductility.

Green synthesis of ZSM-5 using silica fume and catalytic co-cracking of lignin and plastics for production of monocyclic aromatics

ZSM-5 with hierarchical pore structure was synthesized by a simple two-step hydrothermal crystallization from silica fume without using any organic ammonium templates.The synthesized ZSM-5 were oval shaped particles with a particle size about 2.0 μm and weak acid-dominated with proper Brønsted(B)and Lewis(L)acid sites.The ZSM-5 was used for catalytic co-cracking of n-octane and guaiacol,lowdensity polyethylene(LDPE)and alkali lignin(AL)to enhance the production of benzene,toluene,ethylbenzene and xylene(BTEX).The most significant synergistic effect occurred at n-octane/guaiacol at 1:1 and LDPE/AL at 1:3,under the condition,the achieved BTEX selectivity were 24%and 33%(mass)higher than the calculated values(weighted average).The highest BTEX selectivity reached 88.5%,which was 3.7%and 54.2%higher than those from individual cracking LDPE and AL.The synthesized ZSM-5 exhibited superior catalytic performance compared to the commercial ZSM-5,indicating potential application prospect.

Experimental,Numerical,and Analytical Studies on the Bending of Mechanically Lined Pipe

Mechanically lined pipe(MLP)is often used for offshore oil and gas transport because of its low cost and corrosion resistance.During installation and operation,the pipe may undergo severe bending deformation,which causes the liner to separate from the outer pipe and buckles,affecting the stability of the whole line.In this paper,the buckling response of MLP subjected to bending is investigated to clarify its bending characteristics by employing both experiments,numerical simulation,as theoretical methods.Two types of MLPs were manufactured with GB 45 carbon steel(SLP)and Al 6061(ALP)used as the outer pipe material,respectively.The hydraulic expansion and bending experiments of small-scale MLPs are conducted.In addition to the ovalized shape of the cross-section for the SLP specimens,the copper liner was found to wrinkle on the compressive side.In contrast,the liner of ALP remains intact without developing any wrinkling and collapse mode.In addition,a dedicated numerical framework and theoretical models were also established.It was found both the manufacturing and bending responses of the MLP can be well reproduced,and the predicted maximum moment and critical curvatures are in good agreement with the experimental results.

预处理技术--家庭生物废弃物处理过程中的微塑料制造者

Mechanical pretreatment is an indispensable process in biological treatment plants that remove plastics and other impurities from household biogenic waste(HBW).However,the imperfect separation of plas-tics in these pretreatment methods has raised concerns that they pose a secondary formation risk for microplastics(MPs).To validate this presumption,herein,quantities and properties of plastic debris and MPs larger than 50μm were examined in the full chain of three different pretreatment methods in six plants.These facilities received HBW with or without prior depackaging at the source.The key points in the secondary formation of MPs were identified.Moreover,flux estimates of MPs were released,and an analysis of MPs sources was provided to develop an overview of their fate in HBW pretreatment.Pretreated output can contain a maximum of(1673±279)to(3198±263)MP particles per kilogram of wet weight(particles·kg^(-1) ww)for those undepackaged at source,and secondary MPs formation is pri-marily attributed to biomass crushers,biohydrolysis reactors,and rough shredders.Comparatively,HBW depackaged at the source can greatly reduce MPs by 8%-72%,regardless of pretreatment processes.Before pretreatment,4.6-205.6 million MP particles were present in 100 tonnes of HBW.MPs are pro-duced at a rate of 741.11-33124.22billion MP partices annually in anaerobic digester feedstock(ADF).This study demonstrated that HBW pretreatment is a competitive source of MPs and emphasized the importance of implementing municipal solid waste segregation at the source.Furthemore,depack-aging biogenic waste at the source is recommended to substantially alleviate the negative effect of pre-treatment on MPs formation.

Timing effect of high temperature exposure on the plasticity of internode and plant architecture in maize

The occurrence of high temperature(HT)in crop production is becoming more frequent and unpredictable with global warming,severely threatening food security.The state of an organ’s growth and development is largely determined by the temperature conditions it is exposed to over time.Maize is the main cereal crop,and its stem growth and plant architecture are closely related to lodging resistance,and especially sensitive to temperature.However,systematic research on the timing effect of HT on the sequentially developing internode and stem is currently lacking.To identify the timing effect of HT on the morphology and plasticity of the stem in maize,two hybrids(Zhengdan 958(ZD958),Xianyu 335(XY335))characterized by distinct morphological traits in the stem were exposed to a 7-day HT treatment from the V6 to V17 stages(Vn presents the vegetative stage with n leaves fully expanded)in 2019-2020.The results demonstrated that exposure to HT during V6-V12 accelerated the rapid elongation of stems.For instance,HT occurring at V7 and V12 specifically promoted the lengths and weights of the 3rd-5th and 9th-11th internodes,respectively.Meanwhile,HT slowed the growth of internodes adjacent to the promoted internodes.Interestingly,compared with control,the plant height was significantly increased soon after HT treatment,but the promotion effect became narrower at the subsequent flowering stage,demonstrating a self-adjusting mechanism in the maize plant in response to HT.Importantly,HT altered the plant architectures,including a rising of the ear position and increase in the ear position coefficient.XY335 exhibited greater sensitivity in stem development than ZD958 under HT treatment.These findings improve our systematic understanding of the plasticity of internode and plant architecture in response to the timing of HT exposure.

Perspectives in human brain plasticity sparked by glioma invasion:from intraoperative(re)mappings to neural reconfigurations

Exploring the aptitude of the human brain to compensate functional consequences of a lesion damaging its structural architecture is a key challenge to improve patient care in various neurological diseases,to optimize neuroscientifically-informed strategies of postlesional rehabilitation,and ultimately to develop innovative neuro-regenerative therapies.The term‘plasticity’,initially referring to the intrinsic propensity of neurons to modulate their synaptic transmission in a learning situation,was progressively transposed to brain injury research and clinical neurosciences.Indeed,in the event of brain damage,adaptive mechanisms of compensation allow a partial reshaping of the structure and activities of the central nervous system,thus permitting to some extent the maintenance of brain functions.

Exercise-induced adaptation of neurons in the vertebrate locomotor system

Vertebrate neurons are highly dynamic cells that undergo several alterations in their functioning and physiologies in adaptation to various external stimuli.In particular,how these neurons respond to physical exercise has long been an area of active research.Studies of the vertebrate locomotor system’s adaptability suggest multiple mechanisms are involved in the regulation of neuronal activity and properties during exercise.In this brief review,we highlight recent results and insights from the field with a focus on the following mechanisms:(a)alterations in neuronal excitability during acute exercise;(b)alterations in neuronal excitability after chronic exercise;(c)exercise-induced changes in neuronal membrane properties via modulation of ion channel activity;(d)exercise-enhanced dendritic plasticity;and(e)exercise-induced alterations in neuronal gene expression and protein synthesis.Our hope is to update the community with a cellular and molecular understanding of the recent mechanisms underlying the adaptability of the vertebrate locomotor system in response to both acute and chronic physical exercise.

Mitochondrial recruitment in myelin:an anchor for myelin dynamics and plasticity?

Optimal propagation of neuronal electrical impulses depends on the insulation of axons by myelin,produced in the central nervous system by oligodendrocytes.Myelin is an extension of the oligodendrocyte plasma membrane,which wraps around an axon to form a compact multi-layered sheath.Myelin is composed of a substantially higher proportion of lipids compared to other biological membranes and enriched in a small number of specialized proteins.

Glial progenitor heterogeneity and plasticity in the adult spinal cord

Glial progenitor cells were reported to have the capacity to generate various types of cells in both the central nervous system(CNS)and peripheral nervous system.Glial progenitor cells can respond to diverse environmental signals and transform into distinct populations,each serving specific functions.Notably,the adult spinal cord hosts various populations of glial progenitors,a region integral to the central nervous system.During development,glial progenitors express glial fibrillary acidic protein(GFAP;Dimou and Gotz,2014).However,the specific identities of GFAP-expressing progenitors in the adult spinal cord were not thoroughly investigated.

Enhanced prediction of anisotropic deformation behavior using machine learning with data augmentation

Mg alloys possess an inherent plastic anisotropy owing to the selective activation of deformation mechanisms depending on the loading condition.This characteristic results in a diverse range of flow curves that vary with a deformation condition.This study proposes a novel approach for accurately predicting an anisotropic deformation behavior of wrought Mg alloys using machine learning(ML)with data augmentation.The developed model combines four key strategies from data science:learning the entire flow curves,generative adversarial networks(GAN),algorithm-driven hyperparameter tuning,and gated recurrent unit(GRU)architecture.The proposed model,namely GAN-aided GRU,was extensively evaluated for various predictive scenarios,such as interpolation,extrapolation,and a limited dataset size.The model exhibited significant predictability and improved generalizability for estimating the anisotropic compressive behavior of ZK60 Mg alloys under 11 annealing conditions and for three loading directions.The GAN-aided GRU results were superior to those of previous ML models and constitutive equations.The superior performance was attributed to hyperparameter optimization,GAN-based data augmentation,and the inherent predictivity of the GRU for extrapolation.As a first attempt to employ ML techniques other than artificial neural networks,this study proposes a novel perspective on predicting the anisotropic deformation behaviors of wrought Mg alloys.

Microstructure and forming mechanism of metals subjected to ultrasonic vibration plastic forming: A mini review

Compared with traditional plastic forming,ultrasonic vibration plastic forming has the advantages of reducing the forming force and improving the surface quality of the workpiece.This technology has a very broad application prospect in industrial manufactur-ing.Researchers have conducted extensive research on the ultrasonic vibration plastic forming of metals and laid a deep foundation for the development of this field.In this review,metals were classified according to their crystal structures.The effects of ultrasonic vibration on the microstructure of face-centered cubic,body-centered cubic,and hexagonal close-packed metals during plastic forming and the mech-anism underlying ultrasonic vibration forming were reviewed.The main challenges and future research direction of the ultrasonic vibra-tion plastic forming of metals were also discussed.

Dopamine in the prefrontal cortex plays multiple roles in the executive function of patients with Parkinson's disease

Parkinson’s disease can affect not only motor functions but also cognitive abilities,leading to cognitive impairment.One common issue in Parkinson’s disease with cognitive dysfunction is the difficulty in executive functioning.Executive functions help us plan,organize,and control our actions based on our goals.The brain area responsible for executive functions is called the prefrontal co rtex.It acts as the command center for the brain,especially when it comes to regulating executive functions.The role of the prefrontal cortex in cognitive processes is influenced by a chemical messenger called dopamine.However,little is known about how dopamine affects the cognitive functions of patients with Parkinson’s disease.In this article,the authors review the latest research on this topic.They start by looking at how the dopaminergic syste m,is alte red in Parkinson’s disease with executive dysfunction.Then,they explore how these changes in dopamine impact the synaptic structure,electrical activity,and connection components of the prefrontal cortex.The authors also summarize the relationship between Parkinson’s disease and dopamine-related cognitive issues.This information may offer valuable insights and directions for further research and improvement in the clinical treatment of cognitive impairment in Parkinson’s disease.

Upcycling plastic wastes into value-added products via electrocatalysis and photoelectrocatalysis

Plastic,renowned for its versatility,durability,and cost-effectiveness,is indispensable in modern society.Nevertheless,the annual production of nearly 400 million tons of plastic,coupled with a recycling rate of only 9%,has led to a monumental environmental crisis.Plastic recycling has emerged as a vital response to this crisis,offering sustainable solutions to mitigate its environmental impact.Among these recycling efforts,plastic upcycling has garnered attention,which elevates discarded plastics into higher-value products.Here,electrocatalytic and photoelectrocatalytic treatments stand at the forefront of advanced plastic upcycling.Electrocatalytic or photoelectrocatalytic treatments involve chemical reactions that facilitate electron transfer through the electrode/electrolyte interface,driven by electrical or solar energy,respectively.These methods enable precise control of chemical reactions,harnessing potential,current density,or light to yield valuable chemical products.This review explores recent progress in plastic upcycling through electrocatalytic and photoelectrocatalytic pathways,offering promising solutions to the plastic waste crisis and advancing sustainability in the plastics industry.

Temperature effect on nanotwinned Ni under nanoindentation using molecular dynamic simulation

Temperature effect on atomic deformation of nanotwinned Ni (nt-Ni) under localized nanoindentation is investigated in comparison with nanocrystalline Ni (nc-Ni) through molecular simulation.The nt-Ni exhibits enhanced critical load and hardness compared to nc-Ni,where perfect,stair-rod and Shockley dislocations are activated at (111),(111) and (111) slip planes in nt-Ni compared to only SSockley dislocation nucleation at (111) and (111) slip planes of nc-Ni.The nt-Ni exhibits a less significant indentation size effect in comparison with nc-Ni due to the dislocation slips hindrance of the twin boundary.The atomic deformation associated with the indentation size effect is investigated during dislocation transmission.Different from the decreasing partial slips parallel to the indenter surface in nc-Ni with increasing temperature,the temperaturedependent atomic deformation of nt-Ni is closely related to the twin boundary:from the partial slips parallel to the twin boundary (~10 K),to increased confined layer slips and decreased twin migration(300 K–600 K),to decreased confined layer slips and increased dislocation interaction of dislocation pinning and dissociation (900 K–1200 K).Dislocation density and atomic structure types through quantitative analysis are implemented to further reveal the above-mentioned dislocation motion and atomic structure alteration.Our study is helpful for understanding the temperature-dependent plasticity of twin boundary in nanotwinned materials.

Plastic deformation behavior of a Cu-10Ta alloy under strong impact loading

In this work,a Cu-10Ta alloy with a copper to tantalum mass ratio of 9:1 is prepared using powder metallurgy technology.Physical properties of the alloy,including density,microstructure,melting point,and constant-volume specific heat,are tested.Via the split Hopkinson pressure bar(SHPB)and flyerplate impact experiments,the relationship between equivalent stress and equivalent plastic strain of the material is studied at temperatures of 298-823 K and under strain rates of 1×10^(-3)-5.2×10^(3)s^(-1),and the Hugoniot relationship at impact pressures of 1.46-17.25 GPa and impact velocities of 108-942 m/s is obtained.Evolution of the Cu-10Ta microstructure that occurs during high-strain-rate impact is analyzed.Results indicate that the Cu-10Ta alloy possesses good thermal stability,and at ambient temperatures of up to 50%its melting point,stress softening of less than 15%of the initial strength is observed.A modified J-C constitutive model is employed to accurately predict the variation of yield strength with strain rate.Under strong impact,the copper phase is identified as the primary source of plastic deformation in the Cu-10Ta alloy,while significant deformation of the high-strength tantalum particles is less pronounced.Furthermore,the longitudinal wave speed D is found to correlate linearly with the particle velocity u upon strong impact.Analysis reveals that the sound speed and spallation strength of the alloy increase with increasing impact pressure.

The interaction between KIF21A and KANK1 regulates dendritic morphology and synapse plasticity in neurons

Morphological alterations in dendritic spines have been linked to changes in functional communication between neurons that affect learning and memory.Kinesin-4 KIF21A helps organize the microtubule-actin network at the cell cortex by interacting with KANK1;however,whether KIF21A modulates dendritic structure and function in neurons remains unknown.In this study,we found that KIF21A was distributed in a subset of dendritic spines,and that these KIF21A-positive spines were larger and more structurally plastic than KIF21A-negative spines.Furthermore,the interaction between KIF21A and KANK1 was found to be critical for dendritic spine morphogenesis and synaptic plasticity.Knockdown of either KIF21A or KANK1 inhibited dendritic spine morphogenesis and dendritic branching,and these deficits were fully rescued by coexpressing full-length KIF21A or KANK1,but not by proteins with mutations disrupting direct binding between KIF21A and KANK1 or binding between KANK1 and talin1.Knocking down KIF21A in the hippocampus of rats inhibited the amplitudes of long-term potentiation induced by high-frequency stimulation and negatively impacted the animals’cognitive abilities.Taken together,our findings demonstrate the function of KIF21A in modulating spine morphology and provide insight into its role in synaptic function.