SYNTHETIC STUDIES ON BLOOD COMPATIBLE BIOMATERIALSⅡ. SYNTHESIS OF POLY(ETHYLENEGLYCOL MONOMETHYLLTHER ) METHACRYLATE AND ANTITHROMBOGENICITY OF ITS COPOLYMERS

Poly （ethyleneglycol monomethylether） methacrylate （PEGMM）was synthesized by means of the reaction of methacrylyl chloride with sodium monomethylpolyethyleneglycoxide and was characterized by FTIR,;H-NMR,and ultraviolet spectrometries. A series of poly （vinyl alcohol）-graft-PEGMM （PVA-g-PEGMM ）and methyl methacrylate-PEGMM copolymer （PMMA-PEGMM） were prepared and tested for antithrombogenicity in vitro. The results indicate that the antithrombogenicity of the copolymers basically increases with the increasing of the DP of polyoxyethylene （POE） chain and tends to a plateau after the DP around 114,i.e. the long chain structure of POE is favourable to the antithrombogenicityof its copolymers ;moreover, the extent of the improvement ofantithrombogenicity also relates to the PEGMM content of the copolymers and the kind of the matrix that the POE chains are located on. These results are consistent with the anticipation of the hypothesis of maintaining proteins normal conformations for blood compatible bioraaterials.

Comparison of selective flocculation of low grade goethitic iron ore fines using natural and synthetic polymers and a graft copolymer

This study aims to beneficiate low grade goethitic iron ore fines using a selective flocculation process. Selective flocculation studies were conducted using different polymers such as starch amylopectin(AP), poly acrylic acid(PAA), and a graft copolymer(AP-g-PAA). The obtained results were analyzed; they indicate the enhancement of the iron ore grade from 58.49% to 67.52% using AP-g-PAA with a recovery of 95.08%. In addition, 64.45% Fe with a recovery of 88.79% was obtained using AP. Similarly, using PAA, the grade increased to 63.46% Fe with a recovery of 82.10%. The findings are also supported by characterizing concentrates using X-ray diffraction(XRD) and electron probe microanalysis(EPMA) techniques.

Poly(L-lactide)-Poly(ethylene glycol) Multiblock Copolymers: Synthesis and Properties

Poly (L-lactide)-poly(ethylene glycol) multiblock copolymers with predetermined block lengths were synthesized by polycondensation of PLA diols and PEG diacids. These copolymers presented special properties, such as better miscibility between the two components, low crystallinity and better hydrophilicity, which can be modulated by adjusting the block lengths of the two components.

Synthesis and Characterization of Chitosan-g-poly- (D, L-lactic acid) Copolymer

Biodegradable chitosan-g-poly (D, L-lactic acid) copolymers were prepared via two methods. (1) The lactide was grafted onto hydroxyl groups of chitosan by using macromolecular initiator sodium of trimethylsilyl-chitosan, (2) poly (D,L-lactic acid)(PLA) with low molecular weight can be linked to the amino group by coupling activated PLA to trimethylsilyl-chitosan. Two graft copolymers had hydrophilic-hydrophobic character and can be applied as carriers for drug delivery.

Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide) synthesized by ATRP

Novel Y-shaped block copolymers of poly（ethylene glycol） and poly（N-isopropylacrylamide）, PEG-b-（PNIPAM）2, were successfully synthesized through atom transfer radical polymerization （ATRP）. A difunctional macroinitiator was prepared by esterification of 2,2-dichloroacetyl chloride with poly（ethylene glycol） monomethyl ether （PEG）. The copolymers were obtained via the ATRP ofN-isopropylacrylamide （NIPAM） at 30℃ with CuCl/Me6TREN as a catalyst system and DMF/H2O （v/v = 3：1） mixture as solvent. The resulting copolymers were characterized by gel permeation chromatography （GPC） and ^1H NMR. These block copolymers show controllable molecular weights and narrow molecular weight distributions （PDI 〈 1.15）. Their phase transition temperatures and the corresponding enthalpy changes in aqueous solution were measured by differential scanning calorimetry （DSC）. As a result, the phase transition temperature of PEG45-b-（PNIPAM55）2 is higher than that of PNIPAM, however, the corresponding enthalpy change is much lower, indicating the significant influence of the macromolecular composition and architecture on the phase transition.

NOVEL AMPHIPHILIC FLUORESCENT GRAFT COPOLYMER: SYNTHESIS, CHARACTERIZATION AND ENCAPSULATION OF A HYDROPHOBIC AGENT

Novel amphiphilic fluorescent graft copolymer （PVP-PyAHy） was successfully synthesized by the free radical copolymerization of hydrophobic monomer N-（1-pyrenebutyryl）-N＇-acryloyl hydrazide （PyAHy） with hydrophilic precursor polymers of vinyl-functionalized poly（N-vinylpyrrolidone） （PVP） in DMF. The copolymer is amphiphilic and has intrinsic fluorescence. FT-IR, ^1H-NMR, TEM, gel permeation chromatography-multi-angle laser light scattering, UV-Vis spectroscopy and fluorescence spectroscopy were used to characterize this copolymer. The TEM observation shows that the copolymer PVP-PyAHy forms micelles in aqueous solution. Results of fluorometric measurements illustrate that the critical micelle concentration （CMC） value of PVP-PyAHy in aqueous solution is about 0.90 mg/mL. To examine the encapsulation ability of the copolymer in aqueous media, methyl yellow was employed as a model hydrophobic agent. The loading level of the polymer to methyl yellow is 8.8 mg/g. The cytotoxicity assays for Madin Darby Canine Kidney （MDCK） cells shows good biocompatibility of PVP-PyAHy in vitro. These results suggest the potential of this copolymer PVP-PyAHy as drugs delivery carrier and fluorescent tracer.

Poly(GMA/MA/MBAA)Copolymer Beads:a Highly Efficient Support Immobilizing Penicillin G Acylase

The hydrophilic, macroporous and beaded ternary copolymer of glycidyl methacrylate （GMA）/methacrylamide（MA）/N,N＇-methylene-bis（acrylamide）（MBAA）was synthesized using the industrial agents by inverse suspension polymerization. The apparent activity of the immobilized penicillin G acylase reached 1096 IU/g for hydrolysis penicillin G on the beads with diameter of 0.11-0.13 ram, and it changed hardly after 50 cycles. It can be expected to be a good potential in industrial application,

Synthesis and Characterization of Degraded Gelatin Grafted Poly(ε-caprolactone) Copolymers

Hydrophilic degraded gelatin was modified with hydrophobic poly(ε-caprolactone) (PCL) via a chemical grafting route.Firstly,PCL with one hydroxyl end group was prepared by the ring-opening polymerization of εcaprolactone (ε-CL) with tin (Ⅱ) 2-ethylhexanoate as catalyst and n-butyl alcohol as initiator.Secondly,the PCL reacted with isophorone diisocyanate (IPDI) to prepare PCL with isocyanate functional group (PCL-NCO).Hydroxylamine was used to degrade gelatin by the cleavage between asparagine and glycine residues of gelatin.PCL-NCO reacted with the hydroxyl/amino groups of degraded gelatin in a homogeneous system and yielded the PCL modified gelatin copolymers.The gelatin grafted PCL copolymers were measured by means of XRD,FTIR,DSC and 1 H NMR.The results confirmed the conjugation of PCL onto gelatin chains.The PCL modified gelatin can be used as biomaterials owing to their biocompatibility and biodegradation.

Synthesis and characterization of poly(phthalazinone ether nitrile) (PPEN)-polydimethylsiloxane (PDMS) block copolymers

Block copolymers with different backbone compositions have been prepared by the condensation of dimethylamino terminated poly（dimethylsiloxane） （PDMS） and hydroquinone terminated poly（phthalazinone ether nitrile） （PPEN） in the presence of chlorobenzcne/N-methyl pyrrolidone （NMP） as solvents. The products were characterized by FTIR, ^1H NMR and gel permeation chromatography. Differential scanning calorimetry analysis indicated that the block copolymers showed separated microphase.

SYNTHESIS AND CHARACTERIZATION OF AMPHIPHILIC GRAFT COPOLYMER CONTAINING MICROPHASE SEPARATED AND LONG POLY(ETHYLENE OXIDE) SIDE CHAIN STRUCTURES

Acryloyl terminated Poly (ethyleneoxide)macromonomers (PEO-A) with different PEO chain lengths have been prepared by deactivation of PEO alkoxide with acryloyl chloride. A new kind of amphiphilic polystyrene-g-poly (ethylene oxide)graft copolymer containing both microphase separated and PEO side chain structures has been synthesized from radical copolymerization of PEO-A macromonomer with styrene. After careful purification by a newly-developed method called 'selective dissolution', the well-defined structure of the purified copolymers was confirmed by IR, ~1H-NMR and GPC. Various experimental parameters controlling the copolymerization were studied in detail. The results indicated that the feed ratio of styrene to macromonomer(S/M) was the most important determining factor for the composition of the copolymers. A detailed 'comb- model' was proposed to describe the molecular structure of the graft copolymers. Finally, this amphiphilic graft copolymers may readily form microphase separated structures as clearly indicated by transmission electron microscopy.

Improving Polylactide Toughness by Plasticizing with Low Molecular Weight Polylactide-Poly(Butylene Succinate)Copolymer

A low-molecular-weight polylactide-poly(butylene succinate)(PLA-PBS)copolymer was synthesized and incorporated into polylactide(PLA)as a novel toughening agent by solvent casting.The copolymer had the same chemical structure and function as PLA and it was used as a plasticizer to PLA.The copolymer was blended with PLA at a weight ratio from 2 to 10 wt%.Phase separation between PLA and PLA-PBS was not observed from their scanning electron microscopy(SEM)images and the crystal structure of PLA almost remained unchanged based on the X-ray diffraction(XRD)measurement.The melt flow index(MFI)of the blends was higher as the amount of PLA-PBS increased,indicating that the block copolymer did improve the mobility of the PLA chains.Moreover,tensile tests revealed that PLA with greater PLA-PBS copolymer exhibited higher elongation at break and it reached the maximum at 8 wt%of PLA-PBS in PLA,which was around 6 times higher than that of pure PLA.Furthermore,the glass transition temperature,measured by differential scanning calorimetry(DSC),markedly decreased with an increasing amount of the copolymer as it decreased from 61.2℃ for pure PLA to 41.3℃when it was blended with 10 wt%PLA-PBS copolymer.Therefore,the PLA-PBS copolymer was shown to be a promising plasticizer for fully biobased and toughened PLA.

Selective swelling of polysulfone/poly(ethylene glycol) block copolymer towards fouling-resistant ultrafiltration membranes

Fouling resistance of ultrafiltration(UF) membranes is critical for their long-term usages in terms of stable performance, so convenient approaches to prepare fouling-resistant membranes are always anticipated. Herein, we demonstrate the facile fabrication of antifouling polysulfone-block-poly(ethylene glycol)(PSF-b-PEG, SFEG)composite membranes. SFEG layer was coated onto macroporous supports and cavitated by immerging them in acetone/n-propanol following the mechanism of selective swelling induced pore generation. Thus-produced SFEG membranes possessed high permeance and excellent mechanical strength. Meanwhile, the structures and separation performances of the SFEG layers can be continuously tuned through simply changing swelling durations. More importantly, the hydrophilic PEG chains were spontaneously enriched onto the pore walls through swelling treatment, endowing intrinsic antifouling property to the SFEG membranes. Bovine serum albumin(BSA)/humic acid(HA) fouling tests proved the prominent fouling resistance of SFEG membranes, and the fouling resistance is expected to be long-standing because of the firm connection between PEG chains and PSF matrix by covalent bonding.

PREPARATION OF HIGH DENSITY POLYETHYLENE/POLYETHYLENE-BLOCK-POLY(ETHYLENE GLYCOL)COPOLYMER BLEND POROUS MEMBRANES VIA THERMALLY INDUCED PHASE SEPARATION PROCESS AND THEIR PROPERTIES

High density polyethylene （HDPE）/polyethylene-block-poly（ethylene glycol） （PE-b-PEG） blend porous membranes were prepared via thermally induced phase separation （TIPS） process using diphenyl ether （DPE） as diluent. The phase diagrams of HDPE/PE-b-PEG/DPE systems were determined by optical microscopy and differential scanning calorimetry （DSC）. By varying the content of PE-b-PEG, the effects of PE-b-PEG copolymer on morphology and crystalline structure of membranes were studied by scanning electron microscopy （SEM） and wide angle X-ray diffraction （WAXD）. The chemical compositions of whole membranes and surface layers were characterized by elementary analysis, Fourier transform infrared spectroscopy-attenuated total reflection （FTIR-ATR） and X-ray photoelectron spectroscopy （XPS）. Water contact angle, static protein adsorption and water flux experiments were used to evaluate the hydrophilicity, antifouling and water permeation properties of the membranes. It was found that the addition of PE-b-PEG increased the pore size of the obtained blend membranes. In the investigated range of PE-b-PEG content, the PEG blocks could not aggregate into obviously separated domains in membrane matrix. More importantly, PE-b-PEG could not only be retained stably in the membrane matrix during membrane formation, but also enrich at the membrane surface layer. Such stability and surface enrichment of PE-b-PEG endowed the blend membranes with improved hydrophilicity, protein absorption resistance and water permeation properties, which would be substantially beneficial to HDPE membranes for water treatment application.

Synthesis and Characterization of ABBA Block Copolymer of Glycolide and ε-Caprolactone

A biodegradable ABBA block copolymer was synthesized via the ring-opening co-polymerization of ~ε-caprolactone(CL, B) and glycolide(A) by means of step polymerization in the presence of ethylene glycol as an initiator and stannous octanoate as a catalyst at 110 ℃ for 48 h. The molecular length of the PCL pre-polymer(BB) could be adjusted by controlling the molar ratio of the ethylene glycol initiator to ε-caprolactone monomer. The structure and the composition of the block copolymer were determined by the weight ratio of the monomer glycolide(A) to PCL pre-polymer(BB). The block copolymers were characterized by ~ 1H NMR, GPC, DSC and X-ray. The results confirm the successful synthesis of an ABBA block copolymer.

POLYCAPROLACTONE-POLY (ETHYLENE GLYCOL) BLOCK COPOLYMER Ⅲ DRUG RELEASE BEHAVIOR

The drug release behavior of degradable polymer--polycaprolactone-poly (ethyleneglycol)block copolymer(PCE) in vitro was investigated by using 5-Fluoro-uracil (5-Fu) asa model drug under a condition of pH 7. 4 at 37C. It is found that the release rate of 5-Fufrom PCE increased with increasing polyether content of the copolymer. The results showthat the increasing polyether content of the copolymer caused increasing hydrophilicity anddecreasing crystallinity of the PCE copolymer. Thus, the drug release behavior and thedegradable property of the PCE can be controlled by adjusting the composition of thecopolymer.

SYNTHESIS OF NOVEL BLOCK COPOLYMERS OF POLY(3-HYDROXYBUTYRIC ACID)WITH POLY(ETHYLENE GLYCOL)THROUGH ANIONIC POLYMERISATION

A novel kind of copolymer with ABA-type block structure was synthesized by anionic ring-opening polymerization of beta-butyrolactone (beta-BL) in the presence of a PEG-based dicarboxylates as macroinitiators which were prepared by the esterification of aliphatic cyclic anhydride and poly(ethylene glycol) (PEG) oligomers (M-n = 2000, 4000 and 6000) and conversion of potassium dicarboxylates. The resultant copolymers as well as the intermediates were characterized by IR, H-1-NMR and GPC.

DETERMINATION OFTHE CRYSTALLINITY IN DIFFERENT TYPE POLY (OXYETHYLENE-STYRENE)BLOCK COPOLYMERS BY X-RAY DIFFRACTION METHOD

By means of the intensity theory of X-ray scattering and the two-phase concept of high polymer, the basic formula of the crystaUinity in block copolymers has been proposed after the corrections of atomic, temperature, absorption, Lorentz and polarization factor. Application of this method to different type poly (oxyethylene-styrene)block copolymers and the same type block copolymers with different EO contents indicates that the crystallinity in poly (oxyethylene-styrene ) block copolymers increases with the increase of the EO content and decreases in the order: PEO-PS-PEO>PEO-PS>PS-PEO-PS.

SYNTHESIS OF AN AMPHIPHILIC PPESK-g-P(PEGMA)GRAFT COPOLYMER VIA ATRP AND ITS USE IN BLEND MODIFICATION OF PPESK MEMBRANES

Preparation of an amphiphilic graft copolymer having poly(phthalazinone ether sulfone ketone)(PPESK) as main chains was carried out by atom transfer radical polymerization(ATRP).The precursor,chloromethylated PPESK (CMPPESK),was prepared by using chioromethylether as chloromethylation agent.Then,poly(ethylene glycol) methyl ether methacrylate(PEGMA) was used as monomer to synthesize PPESK-g-P(PEGMA) by ATRP method under the catalysis of a cuprous chloride/2,2'-bipyridyl system.PPESK/PPESK-g-P(PEGMA) blend m...

Enzymatic Synthesis and Characterization of Novel Amphiphilic Triblock Copolymer Poly(p-dioxanone-co-5-benzyloxytrimethylene carbonate)-block-poly(ethylene glycol)

Novel amphiphilic triblock copolymer poly（p-dioxanone-co-5-benzyloxytrimethylene carbonate）-block-poly（ethylene glycol）-block-poly（p-dioxanone-co-5-benzyloxytrimethylene carbonate） （p（PDO-co-BTMC）-b-PEG-b-p（PDO-co-BTMC）） was successfully synthesized using immobilized porcine pancreas lipase on porous silica particles （IPPL） as the catalyst for the fLrSt time. 1H NMR, 13C NMR and GPC analysis were used to confirm the structures of resulting copolymers. The molecular weight （Mn） of the copolymer with feed ratio of 69：20：11 （BTMC： PDO： PEG ） was 31300 g/mol and the polydispersity was 1.85, while the Mn decreased to 25000 g/mol and polydispersity of 1.93 with the feed ratio of 50：40：10.

Synthesis and characterization of a novel amphiphilic biodegradable β-cyclodextrin/poly(γ-benzyl L-glutamate) copolymer

β-Cyclodextrin/poly（γ-benzyl L-glutamate） （β-CD-PBLG） copolymers were synthesized by ring-opening polymerization of N- carboxy-γ-benzyl L-glutamate anhydride （BLG-NCA） in N,N-dimethylformamide （DMF） initiated by mono-amino-β-cyclodextrin（H2N-β-CD）. The structures of the copolymers were confirmed by IR, ^1H NMR and GPC. The fluorescence technique was used to determine the critical micelle concentrations （CMC） of copolymer micell solution, the diameter and the distribution of micelles were characterized by DLS. The results showed that BLG-NCA could be initiated by H2N-β-CD to produce copolymer. The nanomicells were formed by these copolymers in water.