Influence of Poly(methylmethacrylate) Dopant on Butadiene Derivative Electroluminescence

Organic electroluminescent (EL) devices with one layer of 1,1 bis( p diethyl aminophenyl) 4,4 diphenyl 1, 3 (DEAB) doped with different quantities of poly(methylmethacrylate) (PMMA) (DEAB/PMMA) as the EL emitting layer, sandwiched between indium/tin oxide (ITO) and aluminum electrodes, have been fabricated by spin coating onto ITO. We found that there is an optimum doping ratio of DEAB to PMMA in the emitting layer for enhancing the EL intensity and efficiency of DEAB/PMMA devices.

New optically active poly(amide-imide)s derived from N,N'-(4,4-diphthaloyl)-bis-L-leucine and hydantoin derivatives:Synthesis and properties

Six new optically active poly（amide-imide）s （5a-f） were synthesized through the direct polycondensation reaction of N,N′-（4,4′- diphthaloyl）-bis-L-leucine （3） with six hydantoin derivatives （4a-f）. Tripbenyl phosphite （TPP）/pyridine in the presence of calcium chloride （CaCl2） and N-methyl-2-pyrrolidone （NMP） were successfully applied for direct polycondensation. The polycondensation reactions produce a series of new poly（amide-imide）s （5a-f） in high yields, and inherent viscosity between 0.42 and 0,55 dL/g. The resulting poly（amide-imide）s （5a-f） were characterized by elemental analysis, viscosity measurements, thermal gravimetric analysis （TGA and DTG）, solubility test and FT-IR spectroscopy.

POLYMERIZATION OF N,N'-(PYROMELLITOYL)-BIS-L-LEUCINE DIACID CHLORIDE WITH HYDANTOIN DERIVATIVES BY MICROWAVE IRRADIATION

Facile and rapid polycondensation reactions of N,N'-(pyromellitoyl)-bis-L-leucine diacid chloride 1 with eight different derivatives of hydantoin compounds 2a-h were developed by using a domestic microwave oven in the presence of a small amount of polar organic medium such as o-cresol. The polycondensation reactions proceeded rapidly, compared with the conventional solution polycondensation, and was completed within 7-10 min, producing a series of novel optically active poly(amide-imide)s 3a-h with high yield and inherent viscosity of 0.35-0.65 dL/g. All of the above polymers were fully characterized by FT-IR, elemental analyses, inherent viscosity (η inh ), solubility test and specific rotation. Some structural characterization and physical properties of these optically active poly(amide-imide)s are reported.

Addition of Per(poly)fluoroalkyl Iodides to vinyl Cyclopropane Derivatives: Synthesis of Fluoroalkyl Substituted γ,δ-Unsaturated Carbonyl Compounds

In the presence of CrC13 /Fe bimetal couple,per(poly)fluoroalkyl iodides add to vinyl cyclopropane compounds giving addition-ring-opening products in good yields.

Big Third-order Nonlinear Optical Properties of Two Poly[(3-alkylthiophene-2, 5-diyl)-(benzylidenequinomethane-2, 5-diyl)] Derivatives

Two novel poly[(3-alkylthiophene-2,5-diyl)-(benzylidenequinomethane-2,5-diyl)s] derivatives, poly[ (3-butylthiophene-2,5-diyl)-( p-N,N-dimethylamino) benzylidenequinomethane-2,5-diyl) ] ( PBTDMABQ) and poly [( 3-octylthiophene2,5-diyl) -(p-N, N-dimethylamino ) benzylidenequinomethane-2, 5-diyl)] (POTDMABQ), were synthesized.The band gaps of the two polymers are calculated as 1. 75 eV for PBTDMABQ and 1. 69 eV for POTDMABQ,respectively. The homogenous films of the two polymers were prepared and their third-ordernonlinear optical properties were studied by the backward degenerate four-wave mixing at 532 nm. Byusing the relative measurement technique, the third-order nonlinear optical susceptibilities ofPBTDMABQ and POTDMABQ are calculated as 5. 62 X 10^(-9) and 1. 22 X 10^(-8) ESU, respectively. It isfound that substituted alky groups have strong effects on the band gap and nonlinear opticalproperties of the two polymers. The relatively big third-order nonlinear optical susceptibilitiesand small band gap of POTDMABQ resulted mainly from the longer alkyl with strong electron-donatingability can enhance the delocation degree of conjugated π electronics.

Synthesis of Methylated β-Cyclodextrins Derived Optically Active Poly(N-diphenylmethyl maleimide)

The methylated β-cyclodextrins derived optically active polymers are firs synthesized through asymmetric polymerization of N-diphenylmethyl maleimide with lithium salt of heptakis(2,6-O-dimethyl) β-cyclodextrin (DM-β-CD) as an initiator. The resulting polymers show negative specific rotation which is opposite in sign to that of DM-β-CD. The asymmetric induction is further confirmed by circular dichroism. The structure is characterized by IR and NMR spectroscopies

ELECTROCHEMICAL BEHAVIOURS OF CYANOETHENYL ANILINE DERIVATIVES

The redox behaviours of the donor-acceptor model compounds, cyanoethenyl aniline derivatives were investigated by cyclic voltammetry and the mechanism of the electrode reaction was studied in detail.

基质细胞衍生因子1修饰左旋聚乳酸多孔微球促进软骨细胞增殖和组织形成

背景:二维培养条件下的软骨细胞增殖及表型维持受限,多孔微球作为支架材料可提供三维培养环境,以更好地模拟体内生长条件。基质细胞衍生因子1是有强趋化效力的稳态细胞因子,能够促进细胞的黏附与增殖。目的:明确接枝基质细胞衍生因子1左旋聚乳酸多孔微球对软骨细胞生物学特性及软骨组织形成的影响。方法:(1)体外验证不同质量浓度基质细胞衍生因子1对兔软骨细胞增殖、迁移、表型维持的影响。(2)采用复乳法制备左旋聚乳酸多孔微球,利用碳二亚胺法将基质细胞衍生因子1接枝于左旋聚乳酸多孔微球上,通过酶联免疫吸附实验及孵育基质细胞衍生因子1特异荧光抗体验证接枝情况。(3)将兔软骨细胞分别接种于左旋聚乳酸多孔微球、接枝基质细胞衍生因子1左旋聚乳酸多孔微球上,检测细胞增殖与黏附。(4)在裸鼠背部皮下分别植入甲基丙烯酰胺基明胶-软骨细胞复合体(对照组)、左旋聚乳酸多孔微球-甲基丙烯酰胺基明胶-软骨细胞复合体(多孔微球组)、接枝基质细胞衍生因子1左旋聚乳酸多孔微球-甲基丙烯酰胺基明胶-软骨细胞复合体(多孔微球修饰组),8周后取材,分别进行组织学染色与成软骨相关基因qRT-PCR检测。结果与结论:(1)相较于0,1 000 ng/mL基质细胞衍生因子1,500 ng/mL基质细胞衍生因子1可促进软骨细胞的增殖与迁移,提升软骨细胞内Ⅱ型胶原、弹性蛋白、增殖细胞核抗原、Bcl-2 mRNA表达;(2)基质细胞衍生因子1成功接枝于左旋聚乳酸多孔微球上,接枝率为93.75%;(3)相较于左旋聚乳酸多孔微球,接枝基质细胞衍生因子1左旋聚乳酸多孔微球可促进软骨细胞的增殖、黏附;(4)裸鼠皮下植入8周后,相较于对照组、多孔微球组,多孔微球修饰组具有更明显的软骨陷窝结构、更丰富的软骨特异性基质和Ⅱ型胶原沉积,弹性蛋白、Ⅱ型胶原、增殖细胞核抗原、Bcl-2 mRNA表达升高。结果表明:接枝基质细胞衍生因子1左旋聚乳酸多孔微球有利于软骨细胞的黏附、增殖、表型维持以及体内软骨组织形成。

Synthesis and Thermal Crosslinking Behavior of Poly(aryl ether ketone)s Containing 1,4-Naphthalene Moieties

A new monomer, 1,4-bis(4-fluorobenzoyl) naphthalene(compound 2) was synthesized via a two-step reaction. 1,4-Naphthalenedicarboxylic acid chloride(compound 1) was prepared by using the acyl chlorization reaction of 1,4-naphthalenedicarboxylic acid with thionyl chloride. The Friedel-Crafts acylation of compound 1 with fluorobenzene afforded compound 2 in a 80% yield. The polycondensation of compound 2 with various bisphenols in tetramethylene sulfone(TMS) in the presence of excess potassium carbonate as a condensation reagent was carried out at 210 ℃ to quantitatively afford the corresponding poly(aryl ether ketone)s(compounds 3_8) containing 1,4-naphthalene moieties. Thermal analyses showed that the polymers have T g values ranging from 496 to 500 K and are thermally stable in air with initial mass loss above 500 ℃. These novel polymers exhibited an excellent solubility in organic solvents including NMP, DMAc, and chloroform, etc. In addition, the glass transition temperatures of these polymers increased and the polymers became insoluble in chloroform after treated at 260 ℃, indicating the occurrence of a thermal crosslinking reaction.

Synthesis and Properties of Poly(aryl ether ketone) Copolymers Containing 2,7-Naphthalene Moieties

Poly（ aryl ether ketone） copolymers containing 2,7-naphthylene and hydroquinone（HQ） moieties with various compositions were prepared by the reaction of 4,4＇-difluorobenzophenone（DFB） 2,7-naphthylene and hydroquinone in the presence of sodium carbonate and potassium carbonate （ 19： 1, mass ratio） in diphenyl sulfone （DPS）. The thermal analysis results of the copolymers show that the glass transition temperatures（Tgs） increase, while the melting temperatures（Tra） and tile 5.0% weight loss temperatures （ Td ） decrease with the increase of the 2,7-naphthalene moieties. For the copolymers synthesized at a molar fraction of 2,7-naphthalene in the difluoro monomers being over 0.30, no peaks corresponding to the cold crystallization temperature and the melting temperature could be detected, indicating that these copolymers are almost amorphous. The crystal structures of the copolymers with a molar fraction of 2,7-naphthalene being less than 0. 30 are rhombic.

Development of a Freeze-Dried Skin Care Product Composed of Hyaluronic Acid and Poly(γ-Glutamic Acid) Containing Bioactive Components for Application after Chemical Peels

Eight types of spongy sheet were prepared by freeze-drying aqueous solutions of hyaluronic acid (HA) and poly(γ-glutamic acid) (PGA) with or without bioactive components including vitamin C derivative (VC), glucosylceramide (GC), and epidermal growth factor (EGF). Spongy sheets were categorized into the following groups: Group I (HA/PGA), Group II (HA/PGA + VC), Group III (HA/PGA + GC), Group IV (HA/PGA + VC, GC), Group V (HA/PGA + EGF), Group VI (HA/PGA + VC, EGF), Group VII (HA/PGA + GC, EGF), and Group VIII (HA/PGA + VC, GC, EGF). In the first experiment, we examined fibroblast proliferation in conditioned medium that had been prepared by immersing each spongy sheet in a conventional culture medium. EGF-incorporating spongy sheets (Groups V-VIII) enhanced fibroblast proliferation more than EGF-free spongy sheets (Groups I-IV). In the second experiment, cytokine production by fibroblasts was evaluated using a wound surface model. This involved elevation of fibroblasts-incorporating collagen gel sheets to the air-liquid interface, on which a spongy sheet (Groups I, IV, V and VIII) was placed and cultured for 1 week. EGF-incorporating spongy sheets (Groups V and VIII) enhanced the production of vascular endothelial growth factor (VEGF) and hepatocyte growth factor (HGF) by fibroblasts more than EGF-free spongy sheets (Groups I and IV). The effect of these four types of spongy sheet on wounds was investigated in animal experiments. Chemical peel was performed by contacting 50% trichloroacetic acid (TCA) on the dorsal region of mice, after which a spongy sheet was placed, and the wound condition was then observed in a two-week period. Angiogenesis was facilitated to a greater degree in Group VIII compared with Groups I, IV and V. This finding indicates that Group VIII spongy sheet is a promising aid for skin recovery after chemical peel.

SINGLE-ION CONDUCTIVITY IN POLY (LITHIUM PROPIONATE METHYL SILOXANE)

Poly(lithium propionate methyl siloxane )as a single-ion carrier source was synthesized. The crosslinked film showed lower lithium ionic conductivity at room temperature (about 10^(-10) S/cm). However,the lithium ionic conductivity was obviously increased by blending with high polar polymers such as polyethylene oxide, poly (methylsiloxane - co- ethylene oxide) and poly (methylsiloxane- g- ethylene oxide). In the blend system a high conductivity of 10^(-7)-10^(-5) Scm^(-1) at room temperature was obtained and the single-ion conductivity was deeply influenced by the content of the poly (lithium propionate methyl siioxane). The dc ionic conductivity of the flexible crosslinked films is more stable over time.

Poly Ethylene Glycols as Efficient Media for the Synthesis of <i>β</i>-Nitro Styrenes from <i>α</i>, <i>β</i>-Unsaturated Carboxylic Acids and Metal Nitrates under Conventional and Non-Conventional Conditions

Poly ethylene glycols (PEG-200, 400, 600, 4000 and 6000) supported reactions were conducted with certain α, β-unsaturated acids in presence of metal nitrates under solvent free (solid state) and mineral acid free conditions. The reactants were ground in a mortar with a pestle for about 30 minutes. The aromatic acids underwent nitro decarboxylation and afforded β-nitro styrene derivatives in very good yield while α, β-unsaturated aliphatic carboxylic acids gave corresponding nitro derivatives. Addition of PEG accelerated rate of the reaction enormously. Reaction times substantially decreased from several hours to few minutes followed by highly significant increase in the product yield. Among the several PEGs PEG-300 has been found to be much more effective than other PEGs.

A combination of chondroitinase ABC,glial cell line-derived neurotrophic factor,and Nogo A antibody delayed-release microspheres for the treatment of spinal cord injury

The purpose of this study was to evaluate the effect of poly（lactide-co-glycolic acid） delayed-release microspheres,which were prepared using glial cell line-derived neurotrophic factor（GDNF）,on the delayed-release,controllability,and protection of GDNF activity.The present study is the first to combine chondroitinase ABC,GDNF,and Nogo A antibody delayed-release microspheres for the treatment of spinal cord injury.Results show that the combined therapy of chondroitinase ABC,GDNF,and Nogo A antibody microspheres can increase the immunoreaction of neurofilament 200 in the injured spinal cord,and this therapeutic effect was better than chondroitinase ABC,GDNF,or Nogo A antibody microspheres administered singularly.

Protein adsorption on the poly(L-lactic acid) surface modified by chitosan and its derivatives

Surface modification of biomaterials has been adopted over the years to improve their biocompatibility. In this study, aiming to promote hydrophilicity and to introduce natural recognition sites onto poly(L-lactic acid) (PLLA) films, chitosan and its derivatives, carboxymethyl chitosan(CMC) and N-methylene phosphonic chitosan (NPC), were used to modify the surface of PLLA films by an entrapment method. Radiolabeled (125I) proteins were used to measure the amount of protein adsorbed to PLLA surfaces. Fibronectin (Fn) was used to study the protein adsorption on the modified PLLA surfaces, including isotherm adsorption and adsorption kinetics of single protein, competitive adsorption of binary proteins system and serum multi-proteins and the desorption behavior in serum solution. The results showed that in the isotherm adsorption, Fn had a larger adsorption capacity on the CS-modified surface at lower concentrations, but had a high adsorption capacity at CMC-modified surface at higher concentrations. In the study of absorption kinetics, Fn had a fastest adsorption equilibrium and a highest equilibrium adsorption capacity at the CS-modified surface, while it was opposite at the PCS-modified surface. When BSA and serum were added, it had the greatest effect on the adsorption of Fn on the PCS-modified surface. After 6 hours soaking in the desorption study, Fn had reached desorption equilibrium on all the modified surfaces, which had different effects on the desorption rate and the remaining percentage of Fn.

聚天冬氨酸及其衍生物的研究进展

聚天冬氨酸和聚天冬酰胺是一类性能优异的高分子材料,在药物控释、组织工程等许多领域应用广泛。综述了近年来国内外对该领域研究的进展。

静电纺丝聚乳酸/聚己内酯共混纤维支架与兔脂肪源干细胞的体外生物相容性研究

目的利用兔脂肪源干细胞评价静电纺丝聚乳酸/聚己内酯共混纤维支架的生物相容性。方法脂肪源干细胞取自新西兰白兔皮下脂肪组织,经分离、培养后接种到待检支架上,使用倒置相差显微镜和扫描电镜观察细胞在支架上的生长形态;MTT法比较支架上培养和常规培养条件下的脂肪源干细胞生长曲线与倍增时间。结果脂肪源干细胞在纤维支架上生长良好,生长曲线与常规培养时基本一致,两组间细胞倍增时间差异无统计学意义(P>0.05)。结论脂肪源干细胞能够在静电纺丝聚乳酸/聚己内酯共混纤维支架材料上正常生长增殖,该支架材料生物相容性好。

季铵化聚4-乙烯吡啶衍生物与葫芦脲[6]的超分子自组装及性质研究

通过葫芦[6]脲(CB[6])与季铵化聚4-乙烯吡啶衍生物2在水溶液中于室温下进行超分子组装,得到一种新型的超分子聚合物3,并通过1HNMR,IR,元素分析,X射线粉末衍射分析(XRD)对其结构进行了表征,证实CB[6]位于2的侧基脂肪链上,通过非共价键与2结合;通过热重分析(TGA)、紫外-可见吸收(UV-vis)对其性质进行了研究,证实了超分子聚合物3比相应的聚合物2有更高的热稳定性,以及更强的UV-vis吸收.

聚苯胺在聚合物发光二极管中的空穴传输作用

报道了聚苯胺中间氧化态(emeraldine base form PANI-EB)空穴传输层对以PPV衍生物(PTA-PPV,PTA-DMPPV和MEH-PPV)为发光层和Alq3为电子传输层构成的多层结构的发光二极管的影响。实验结果表明,在器件中PANI-EB空穴层的引入能有效地降低器件的启亮电压和提高器件的发光亮度,其影响程度依赖于PPV衍生物的结构。

各种烷氧基取代聚对苯乙炔的合成和发光性能研究

利用脱氯缩合聚合法合成了聚 ( 2 甲氧基 5 丁氧基 )对苯乙炔 (PMOBOPV)、聚 ( 2 甲氧基 5 辛氧基 )对苯乙炔 (PMOCOPV)和聚 ( 2 丁氧基 5 丁氧基 )对苯乙炔 (PDBOPV)、聚 ( 2 辛氧基 5 辛氧基 )对苯乙炔 (PD COPV) 4种发光材料。对反应体系的浓度、酸碱度、反应温度及时间等工艺条件和路线进行了细致的研究。结果表明 :反应物的纯度、含量对合成产物的产率和性能有较大的影响 ;碱性是影响脱氯缩合反应的关键因素 ;而反应温度和时间对缩合反应影响则相对较小 ,在一定温度下当反应时间达到一定阶段后其转化率基本不变。对合成材料的化学结构、物理性能和发光特性进行了表征和检测。结果显示 :非对称烷氧基取代PPV具有良好的溶解性、成膜性和稳定性 ;而对称性烷氧基取代PPV的溶解性和成膜性相对较差。以PMOBOPV为发光材料 ,采用旋涂工艺制作出单层和双层发光器件 。