Removal of manganese from waste water by complexation-ultrafiltration using copolymer of maleic acid and acrylic acid

Copolymer of maleic acid and acrylic acid （PMA-100）, combining with polyvinyl butyral （PVB） ultrafiltration membrane was used for the removal of Mn（II） from waste water by complexation-ultrafiltration. The carboxylic group content of PMA-100 and the rate of complexation reaction were measured. Effects of the mass ratio of PMA-100 to Mn（II） （n）, pH, background electrolyte, etc on the rejection rate （R） and permeate flux （J） were investigated. The results show that carboxylic group content of PMA-100 is 9.5 mmol/g. The complexation of Mn（II） with PMA-100 is rapid and completed within 5 min at pH 6.0. Both R and J increase with pH increasing in the range of 2.5-7.0, and R increases with the increase of n at pH 6.0 while J is little affected. The background electrolyte leads to the decrease of R, and CaCl2 has much greater effect on R than NaCl at the same ionic strength.

Antimicrobial Expanded Polytetrafluoroethylene Film Prepared by 3-ray Radiation Induced Grafting of Poly（acrylic acid）

The simultaneous γ-ray-radiation-induced grafting polymerization of acrylic acid on ex- panded polytetrafluoroethylene （ePTFE） film was investigated. It was found that the degree of grafting （DG） of poly（acrylic acid） （PAA） can be controlled by the monomer concentration, absorbed dose, and dose rate under an optimal inhibitor concentration of [Fe2＋]=18 mmol/L. SEM observation showed that the macroporous structure in ePTFE films would be covered gradually with the increase of the DG of PAA. The prepared ePTFE-g-PAA film was im- mersed in a neutral silver nitrate solution to fabricate an ePTFE-g-PAA/Ag hybrid film after the addition of NaBH4 as a reduction agent of Ag＋ to Ag atom. SEM, XRD, and XPS results proved that Ag nanoparticles with a size of several tens of nanometers to 100 nanometers were in situ immobilized on ePTFE film. The loading capacity of Ag nanoparticles could be tuned by the DG of PAA, and determined by thermal gravimetric analysis. The quart- titative antibacterial activity of the obtained ePTFE-g-PAA/Ag hybrid films was measured using counting plate method. It can kill all the Escherichia coli in the suspension in 1 h. Moreover, this excellent antibacterial activity can last at least for 4 h. This work provides a facile and practical way to make ePTFE meet the demanding antimicrobial requirement in more and more practical application areas.

Pretreatment of poly(acrylic acid) sodium by continuous diafiltration and time revolution of filtration potential

The pretreatment for the removal of small molecules from poly(acrylic acid) sodium (PAAS) solution by continuous diafiltration was investigated using ultrafiltration membrane. The effects of PAAS concentration, pH, trans-membrane pressure and pretreatment time on the permeate concentration and permeate flux were studied. The results show that the necessary pretreatment time (NPT) increases with PAAS concentration, decreases with TMP. The change trend of permeate flux with time is affected by pH. The permeate fluxes rapidly decrease from the start, and then increase gradually to stable values at pH 5.0, pH 7.0 and pH 9.3. However, it decreases gradually with time till a state value at pH 3.0 (iso-electric point, IEP). The removal of small molecules is easy at pH greater than iso-electric point (IEP). The change of filtration potential with time indicates the similar trend to that of permeation concentration, but the former is more convenient for indication of NPT.

Redox active polymer metal chelates for use in flexible symmetrical supercapacitors:Cobalt-containing poly(acrylic acid)polymer electrolytes

The novel polymer metal chelate electrolytes(polychelates)were prepared by incorporation of cobalt sulfate(Co)into poly(acrylic acid)(PAA)host matrix.Quasi-solid state supercapacitor devices were fabricated using polychelates,PAA-Co X(X:3,5,7,and 10)where X represents the doping fraction(w/w)of Co in PAA.All polymer metal electrolytes were showed excellent bending-stretching properties,thermal stability and electrochemical durability with an optimum ionic conductivity of 3.15×10^(-4) S cm^(-1).Hierarchically porous activated carbon and nano-sized conductive carbon were used to form carbon composite symmetrical device electrodes.The electric double-layer capacitor(EDLC)and redox reactions of Co-incorporated polychelates at the interfaces of porous activated carbon provided an optimum specific capacitance of 341.33 F g^(-1) with a device of PAA-Co7,which is at least 15 times enhancement compared to the device of pristine PAA.The PAA-Co7 device also provided energy density of 21.25 Wh kg^(-1) at a power density of 117.69 W kg^(-1).A prolonged cyclic stability of the device exhibited superior capacitive performance after 10,000 charge-discharge cycles and the maintained 90%of its initial performance.In addition,the supercapacitor with a dimension of 1.5 cm×3 cm containing PAA-Co7 successfully operated the red-blue-green(RGB)LED light.

CONFORMATIONAL CHARACTERISTICS OF POLY(ACRYLIC ACID) AND POLY(METHACRYLIC ACID)

A full-relaxation optimization of molecule and the Dreiding force field are employed to obtain the geometry parameters and the conformational energy surfaces of meso or racemic dyad of poly(acrylic acid) (PAA) and poly(methacrylic acid) (PMAA). Three different carbonyl-bond orientations of side-groups resulted in the differences in depth of potential wells in their energetic contours for a meso or a racemic dyad. These discrepancies are interpreted as a result of various fine structures corresponding to grid search conformations as well as thereby different interactions. The analysis on the most stable conformations of PMAA confirmed that the ester groups are nearly perpendicular to the plane defined by the two adjacent skeletal bonds but may possibly change their relative orientations to meet the requirement of lower energy during the conformational state transition. For each polymer, two global energy maps of a meso and a racemic dyad were finally constructed from the superposition of energy data for the three kinds of side-group orientations by the Boltzmann factors. From an ensemble average, the proposed scheme with three rotational isomeric states (RIS) allowed us to access the experimentally unperturbed dimensions of PAA chain via the configurational statistical mechanics. Although the calculation was based on the short-range, local interactions, it was interested to note that the experimental characteristic ratios just fell within the range calculated for atactic chains.

PREPARATION OF POLY(ETHYLENEGLYCOL-co-ACRYLIC ACID) MICROSPHERES WITH DIVINYLBENZNE AS CROSSLINKER BY DISTILLATION-PRECIPITATION POLYMERIZATION

Monodisperse poly（poly（ethyleneglycol） methyl ether acrylate-co-acrylic acid） （poly（PEGMA-co-AA）） microspheres were prepared by distillation-precipitation polymerization with divinylbenzene （DVB） as crosslinker with 2,2＇- azobisisobutyronitrile （AIBN） as initiator in neat acetonitrile without stirring. Under various reaction conditions, four distinct morphologies including the sol, microemulsion, microgels and microspheres were formed during the distillation of the solvent from the reaction system. A 2D morphological map was established as a function of crosslinker concentration and the polar monomer AA concentration, in comonomer feed in the transition between the morphology domains. The effect of the covalent crosslinker DVB on the morphology of the polymer network was investigated in detail at AA fraction of 40 vol%. The ratios of acid to ethylene oxide units presenting in the comonomers dramatically affected the polymer-polymer interaction and hence the morphology of the resultant polymer network. The covalent crosslinking by DVB and the hydrogen bonding crosslinking between two acid units as well as between the acid and ethylene oxide unit played key roles in the formation of monodisperse polymer microspheres.

Poly (Acrylamide-co-Acrylic Acid) Hydrogel Induced by Glow-Discharge Electrolysis Plasma and Its Adsorption Properties for Cationic Dyes

In this paper, poly （acrylamide-co-acrylic acid） （P（AM-co-AA）） hydrogel was pre- pared in an aqueous solution by using glow-discharge electrolysis plasma （GDEP） induced copoly- merization of acrylamide （AM） and acrylic acid （AA）, in which N,N＇-methylenebisacrylamide （MBA） was used as a crosslinker. A mechanism for the synthesis of P（AM-co-AA） hydrogel was proposed. To optimize the synthesis condition, the following parameters were examined in detail： the discharge voltage, discharge time, the content of the crosslinker, and the mass ratio of AM to AA. The results showed that the optimum pH range for cationic dyes removal was found to be 5.0-10.0. The P（AM-co-AA） hydrogel exhibits a very high adsorption potential and the ex- perimental adsorption capacities for Crystal violet （CV） and Methylene blue （MB） were 2974.3 mg/g and 2303.6 mg/g, respectively. The adsorption process follows a pseudo-second-order kinetic model. In addition, the adsorption mechanism of P（AM-co-AA） hydrogel for cationic dyes was also discussed.

Molecular Imprinting Fibrous Membranes of Poly(acrylonitrile-co-acrylic acid) Prepared by Electrospinning

IntroductionOver the past few decades, molecular imprinting has been described as a technology for preparing ＂molecular doors＂ which can be matched to ＂template keys＂. It has been found to be a simple and effective approach to introduce specific recognition sites into synthetic polymers, namely, to create molecular imprinting polymers Remarkable features such as stability, ease of preparation and low cost, have made molecular imprinting polymers particularly attractive in chemical sensors, catalysis, drug delivery, and dedicated separations. Practical applications of molecular imprinting polymers require accessible sites, fast mass transfer, and quick binding. However, present techniques used to prepare molecular imprinting polymers most often result in materials exhibiting a high affinity and selectivity but a low capacity and poor site accessibility for the target molecules. It is also very difficult to remove the imprinted molecules located in these molecular imprinting polymers because the highly cross-linked structures do not allow the templates to move freely. To some extent, combining molecular imprinting technology with membrane separation and surface imprinting can overcome the shortcomings, such as mass transfer limitations and non-quantitative recovery of the template molecules seen for imprinted materials fabricated by conventional bulk methods. In that ease, it appears to us that molecular imprinting polymers with high surface area to volume ratios are particularly desirable for largescale applications. Eleetrospun nano and ultrafine fibrous membranes are the most suitable materials due to advantages such as： （1） large specific surfaces, providing relatively high imprinting sites per unit mass; （2） fine porous structures, resulting in the accessibility of imprinting sites and low diffusion resistance necessary for high efficiency; and （3） easy recoverability from practical operation or applicability for continuous usages. Therefore, in this work, we prepared a unique kind of imprinted material--molecularly imprinted fibrous membranes of poly （ acrylonitrile-co-acrylic acid） fabricated by means of an electrospinning process.

Synthesis and Properties of IPN Hydrogels Based on Konjac Glucomannan and Poly(acrylic acid)

Novel interpenetrating polymer network （IPN） hydrogels based on konjac glucomannan （KGM） and poly（acrylic acid） （PAA） were prepared by polymerization and cross-linking of acrylic acid （AA） in the pre-fabricated KGM gel. The IPN gel was analyzed by FF-IR. The studies on the equilibrium swelling ratio of IPN hydrogels revealed their sensitive response to environmental pH value. The results of in vitro degradation showed that the IPN hydrogels retain the enzymatic degradation character of KGM.

Swelling Behaviors of Polyaniline-Poly(Acrylic Acid) Hydrogels

Using poly（acrylic acid） （PAA） aqueous solution, NaOH aqueous solution, aniline （An） and ammonium persulfate （APS）, PAn-PAA hydrogels with a semi-interpenetrating structure connected by physical interlocks, chemical ion bonds and hydrogen bonds were prepared. The swelling properties of the hydrogels in solutions of different pH values （adjusted by adding NaOH or HCI） were studied. All the hydrogels prepared have similar swelling curves （the curves of equilibrium swelling ratio vs. pH value） and reach their maximum swelling at pH of 8 - 10. The maximum swelling ratio of the hydrogels is dependent on composition, including molecular weight of PAA, polymer content of the hydrogel, and molar ratios of AA to An, APS to An, and NaOH to AA, And the compositional dependence of the swelling capacity of PAn-PAA hydrogels was also studied.

Preparation and Properties of Carrageenan-g-Poly(Acrylic Acid)/Bentonite Superabsorbent Composite

A novel biopolymer-based superabsorbent hydrogel composite based on kappa-carrageenan (κC) have been prepared via graft copolymerization of acrylic acid (AA) in the presence of bentonite powder using methylenebisacrylamide (MBA) as a crosslinking agent and ammonium persulfate (APS) as an initiator. The hydrogel structure was confirmed using FTIR spectroscopy and the morphology of the samples was examined by scanning electron microscopy (SEM). The affecting variables onto graft polymerization (i.e. AA, MBA and APS concentration, as well as the bentonite amount) were systematically optimized to achieve a hydrogel with swelling capacity as high as possible. The results of Brunauer–Emmett–Teller (BET) analysis showed that the average pore diameter of the synthesized hydrogel was 11.5 nm. The effect of various salt media and solutions with different pHs on the swelling of the superabsorbent was also studied.

Synthesis and application of a novel star-hyperbranched poly(acrylic acid) for improved dental restoratives

A new star-hyperbranched poly(acrylic acid) has been synthesized and incorporated into dental glassionomer cement for enhanced mechanical strengths. The effects of arm number and branching on viscosity of the polymer aqueous solution and mechanical strengths of the formed experimental cement were evaluated. It was found that the higher the arm number and the more the branching, the lower the viscosity of the polymer solution as well as the mechanical strengths of the formed cement. It was also found that the experimental cement exhibited significantly higher mechanical strengths than commercial Fuji II LC. The experimental cement was 51% in CS, 55% in compressive modulus, 118% in DTS, 82% in FS, 18% in FT and 85% in KHN higher than Fuji II LC. The experimental cement was only 6.7% of abrasive and 10% of attritional wear depths of Fuji II LC in each wear cycle. It appears that this novel experimental cement is a clinically attractive dental restorative and may potentially be used for high-wear and high-stress-bearing site restorations.

Studies on Micellization of a Polystyrene-b-poly(acrylic acid) Copolymer in Aqueous Media by Pyrene Fluorescence

Pyrene probe and TEM have been employed to investigate the behavior of a polystyrene-b-poly(acrylic acid) (PS-b-PAA) copolymer in aqueous solution. A significant annealing temperature effect on the I1/I3 ratio of pyrene was observed and was interpreted in terms of the morphological change of micellar cores. Annealing at a temperature higher than the glass transition temperature (Tg) of PS leads to densification of the hydrophobic core.

Poly(Acrylamide-Co-Acrylic Acid)-Zinc Acetate Polymer Electrolytes: Studies Based on Structural and Morphology and Electrical Spectroscopy

Solid polymer electrolytes (SPEs) of polyacrylamide-co-acrylic acid (PAA) as the polymer host and zinc acetate (ZnA) as an ionic dopant were prepared using a single solvent by the solution casting technique. The amorphous and crystalline structures of film were investigated by X-ray diffraction (XRD). The surface morphology of samples was examined by scanning electron microscopy (SEM). The composition and complex formation of films were characterized by Fourier transform infrared (FTIR) spectroscopy. The conductivity of the PAA-ZnA films was determined by electrochemical impedance spectroscopy. According to the XRD and FTIR analyses, all electrolyte films were in amorphous state and the existence of interaction between Zn2+ cations and the PAA structure confirms that the film was successfully prepared. The SEM observations reveal that the electrolyte films appeared to be rough and flat with irregularly shaped surfaces. The highest ionic conductivity (σ) of 1.82 × 10-5 Scm-1 was achieved at room temperature (303 K) for the sample containing 10 wt % ZnA.

Nano-Li3V2（PO4）3/C Synthesized by Thermal Polymerization Method as Cathode Material for Lithium Ion Batteries

A nano-Li3V2（PO4）3/C powder was successfully prepared by a thermal polymerization method. The particle sizes of the intermediate product powder and the final product Li3V2（PO4）3 are all less than 200 nm. The carbon is partially coated on the surface of Li3V2（PO4）3 particles and the rest exists between particles with a total carbon content of 4.6wt%. This nano-Li3V2（PO4）3/C sample shows a discharge capacity of 124 mAh/g with-out capacity fading after 100 cycles at 0.1 C in the voltage rang of 3.0-4.3 V. Excellent rate performance is also achieved with a capacity of 80 mAh/g at 20 C in 3.0-4.3 V and 100 mAh/g at 10 C in 3.0-4.8 V. This study suggests that the thermal polymerization method is suitable to synthesize nano-Li3V2（PO4）3/C materials.

3D打印工艺参数对PLA/PTW共混物力学性能影响的研究

采用3D打印中的熔融沉积成型(FDM)工艺制备了聚乳酸/乙烯-丙烯酸丁酯-甲基丙烯酸缩水甘油酯共聚物(PLA/PTW),通过单因素实验探究了3D打印工艺参数(喷头温度、打印平台温度和打印速度)对PLA/PTW共混物力学性能的影响,并在此基础上设计了三因素三水平正交实验,优化了3D打印的工艺参数。结果表明,共混物的冲击强度和拉伸强度均随喷头温度的增加呈现先上升后下降、均随打印平台温度的增加而增加、均随打印速度的增加出现下降的趋势。各工艺参数对PLA/PTW共混物综合力学性能的影响从大到小依次为:喷头温度、打印速度、打印平台温度,且当喷头温度为210℃、打印平台温度为80℃以及打印速度为40 mm/s时,打印出的PLA/PTW共混物的综合力学性能最佳。

纳米富锂锰基正极材料的合成及性能研究

富锂层状氧化物材料具有较高的比容量,被认为是下一代先进锂离子电池正极材料。采用丙烯酸热聚合法和柠檬酸溶胶-凝胶法分别合成了纳米富锂锰基正极材料Li_(1.2)Mn_(0.54)Ni_(0.13)Co_(0.13)O_(2),并进行Mg^(^(2+))掺杂改性。通过扫描电子显微镜、X射线粉末衍射仪对制备的正极材料进行形貌和结构表征,并组装成纽扣电池进行充放电性能测试和电化学阻抗谱分析。结果表明,丙烯酸热聚合法合成的正极材料粒径均匀,结晶度更高;与未掺杂样品相比,掺杂Mg^(2+)的正极材料首次库伦效率从67.66%提高到73.34%,循环性能显著改善。

沥青路面水性聚氨酯丙烯酸热反射涂料制备

以异佛尔酮二异氰酸酯(IPDI)、聚丙二醇(PPG)等原料制备水性聚氨酯(WPU),通过丙烯酸单体和交联剂改性WPU制得水性聚氨酯丙烯酸(WPUA)乳液。利用傅里叶变换红外光谱(FTIR)分析WPUA的官能团,利用铅笔硬度和百格划线法对WPUA膜的硬度、附着力进行测定,利用水接触角试验对WPUA膜的疏水性能进行测试;以降温值、黏度值、光泽度作为评价指标,借助正交试验设计确定WPUA热反射涂料的最佳配方;通过室内太阳辐射模拟装置以及室外太阳照射试验对WPUA热反射涂料的降温效果进行测试。结果表明,WPUA膜的附着力和硬度均得到提高,具有较好的疏水性;WPUA热反射涂料的最佳制备配方为固含量30%的WPUA乳液、16%的金红石型钛白粉、2%的石英砂和4%的中空玻璃微珠。WPUA热反射涂料室内外降温效果显著。

超韧聚乳酸/乙烯丙烯酸丁酯甲基丙烯酸缩水甘油酯共混物的制备与性能

向聚乳酸(PLA)和乙烯丙烯酸丁酯甲基丙烯酸缩水甘油酯(EBA-GMA)接枝共聚物的共混物PLA/EBA-GMA(质量比,70/30)中引入催化剂(N,N-二甲基十八胺,DMSA),通过促进PLA与EBA-GMA的原位反应增容来提高共混体系的冲击韧性,并研究了DMSA质量分数对共混体系力学性能的影响。结果显示,未添加DMSA时,PLA/EBA-GMA(70/30)共混物的冲击强度仅为10.9 kJ/m^(2)。当DMSA质量分数为0.5%时,PLA/EBA-GMA(70/30)共混物的冲击强度高达63.1 kJ/m^(2)。共混物结构与形态表征结果表明,添加少量DMSA就能有效促进EBA-GMA上环氧基团与聚乳酸端基的反应活性,提高PLA/EBA-GMA共混物的冲击韧性。

Self-healing poly(acrylic acid) hydrogels fabricated by hydrogen bonding and Fe^(3+) ion cross-linking for cartilage tissue engineering

Autonomous self-healing hydrogels were achieved through a dynamic combination of hydrogen bonding and ferric ion(Fe^(3+))migration.N,N′-methylenebis(acrylamide)(MBA),a cross-linking agent,was added in this study.Poly(acrylic acid)(PAA)/Fe^(3+)and PAA–MBA/Fe^(3+)hydrogels were prepared by introducing Fe^(3+)into the PAA hydrogel network.The ionic bonds were formed between Fe^(3+)ions and carboxyl groups.The microstructure,mechanical properties,and composition of hydrogels were characterized by field emission scanning electron microscopy and Fourier transform infrared spectroscopy.The experimental results showed that PAA/Fe^(3+)and PAA–MBA/Fe^(3+)hydrogels healed themselves without external stimuli.The PAA/Fe^(3+)hydrogel exhibited good mechanical properties,i.e.,the tensile strength of 50 kPa,the breaking elongation of 750%,and the self-healing efficiency of 82%.Meanwhile,the PAA–MBA/Fe^(3+)hydrogel had a tensile strength of 120 kPa.These fabricated hydrogels are biocompatible,which may have promising applications in cartilage tissue engineering.