Removal of manganese from waste water by complexation-ultrafiltration using copolymer of maleic acid and acrylic acid

Copolymer of maleic acid and acrylic acid （PMA-100）, combining with polyvinyl butyral （PVB） ultrafiltration membrane was used for the removal of Mn（II） from waste water by complexation-ultrafiltration. The carboxylic group content of PMA-100 and the rate of complexation reaction were measured. Effects of the mass ratio of PMA-100 to Mn（II） （n）, pH, background electrolyte, etc on the rejection rate （R） and permeate flux （J） were investigated. The results show that carboxylic group content of PMA-100 is 9.5 mmol/g. The complexation of Mn（II） with PMA-100 is rapid and completed within 5 min at pH 6.0. Both R and J increase with pH increasing in the range of 2.5-7.0, and R increases with the increase of n at pH 6.0 while J is little affected. The background electrolyte leads to the decrease of R, and CaCl2 has much greater effect on R than NaCl at the same ionic strength.

Antimicrobial Expanded Polytetrafluoroethylene Film Prepared by 3-ray Radiation Induced Grafting of Poly（acrylic acid）

The simultaneous γ-ray-radiation-induced grafting polymerization of acrylic acid on ex- panded polytetrafluoroethylene （ePTFE） film was investigated. It was found that the degree of grafting （DG） of poly（acrylic acid） （PAA） can be controlled by the monomer concentration, absorbed dose, and dose rate under an optimal inhibitor concentration of [Fe2＋]=18 mmol/L. SEM observation showed that the macroporous structure in ePTFE films would be covered gradually with the increase of the DG of PAA. The prepared ePTFE-g-PAA film was im- mersed in a neutral silver nitrate solution to fabricate an ePTFE-g-PAA/Ag hybrid film after the addition of NaBH4 as a reduction agent of Ag＋ to Ag atom. SEM, XRD, and XPS results proved that Ag nanoparticles with a size of several tens of nanometers to 100 nanometers were in situ immobilized on ePTFE film. The loading capacity of Ag nanoparticles could be tuned by the DG of PAA, and determined by thermal gravimetric analysis. The quart- titative antibacterial activity of the obtained ePTFE-g-PAA/Ag hybrid films was measured using counting plate method. It can kill all the Escherichia coli in the suspension in 1 h. Moreover, this excellent antibacterial activity can last at least for 4 h. This work provides a facile and practical way to make ePTFE meet the demanding antimicrobial requirement in more and more practical application areas.

Pretreatment of poly(acrylic acid) sodium by continuous diafiltration and time revolution of filtration potential

The pretreatment for the removal of small molecules from poly(acrylic acid) sodium (PAAS) solution by continuous diafiltration was investigated using ultrafiltration membrane. The effects of PAAS concentration, pH, trans-membrane pressure and pretreatment time on the permeate concentration and permeate flux were studied. The results show that the necessary pretreatment time (NPT) increases with PAAS concentration, decreases with TMP. The change trend of permeate flux with time is affected by pH. The permeate fluxes rapidly decrease from the start, and then increase gradually to stable values at pH 5.0, pH 7.0 and pH 9.3. However, it decreases gradually with time till a state value at pH 3.0 (iso-electric point, IEP). The removal of small molecules is easy at pH greater than iso-electric point (IEP). The change of filtration potential with time indicates the similar trend to that of permeation concentration, but the former is more convenient for indication of NPT.

Redox active polymer metal chelates for use in flexible symmetrical supercapacitors:Cobalt-containing poly(acrylic acid)polymer electrolytes

The novel polymer metal chelate electrolytes(polychelates)were prepared by incorporation of cobalt sulfate(Co)into poly(acrylic acid)(PAA)host matrix.Quasi-solid state supercapacitor devices were fabricated using polychelates,PAA-Co X(X:3,5,7,and 10)where X represents the doping fraction(w/w)of Co in PAA.All polymer metal electrolytes were showed excellent bending-stretching properties,thermal stability and electrochemical durability with an optimum ionic conductivity of 3.15×10^(-4) S cm^(-1).Hierarchically porous activated carbon and nano-sized conductive carbon were used to form carbon composite symmetrical device electrodes.The electric double-layer capacitor(EDLC)and redox reactions of Co-incorporated polychelates at the interfaces of porous activated carbon provided an optimum specific capacitance of 341.33 F g^(-1) with a device of PAA-Co7,which is at least 15 times enhancement compared to the device of pristine PAA.The PAA-Co7 device also provided energy density of 21.25 Wh kg^(-1) at a power density of 117.69 W kg^(-1).A prolonged cyclic stability of the device exhibited superior capacitive performance after 10,000 charge-discharge cycles and the maintained 90%of its initial performance.In addition,the supercapacitor with a dimension of 1.5 cm×3 cm containing PAA-Co7 successfully operated the red-blue-green(RGB)LED light.

PREPARATION OF POLY(ETHYLENEGLYCOL-co-ACRYLIC ACID) MICROSPHERES WITH DIVINYLBENZNE AS CROSSLINKER BY DISTILLATION-PRECIPITATION POLYMERIZATION

Monodisperse poly（poly（ethyleneglycol） methyl ether acrylate-co-acrylic acid） （poly（PEGMA-co-AA）） microspheres were prepared by distillation-precipitation polymerization with divinylbenzene （DVB） as crosslinker with 2,2＇- azobisisobutyronitrile （AIBN） as initiator in neat acetonitrile without stirring. Under various reaction conditions, four distinct morphologies including the sol, microemulsion, microgels and microspheres were formed during the distillation of the solvent from the reaction system. A 2D morphological map was established as a function of crosslinker concentration and the polar monomer AA concentration, in comonomer feed in the transition between the morphology domains. The effect of the covalent crosslinker DVB on the morphology of the polymer network was investigated in detail at AA fraction of 40 vol%. The ratios of acid to ethylene oxide units presenting in the comonomers dramatically affected the polymer-polymer interaction and hence the morphology of the resultant polymer network. The covalent crosslinking by DVB and the hydrogen bonding crosslinking between two acid units as well as between the acid and ethylene oxide unit played key roles in the formation of monodisperse polymer microspheres.

CONFORMATIONAL CHARACTERISTICS OF POLY(ACRYLIC ACID) AND POLY(METHACRYLIC ACID)

A full-relaxation optimization of molecule and the Dreiding force field are employed to obtain the geometry parameters and the conformational energy surfaces of meso or racemic dyad of poly(acrylic acid) (PAA) and poly(methacrylic acid) (PMAA). Three different carbonyl-bond orientations of side-groups resulted in the differences in depth of potential wells in their energetic contours for a meso or a racemic dyad. These discrepancies are interpreted as a result of various fine structures corresponding to grid search conformations as well as thereby different interactions. The analysis on the most stable conformations of PMAA confirmed that the ester groups are nearly perpendicular to the plane defined by the two adjacent skeletal bonds but may possibly change their relative orientations to meet the requirement of lower energy during the conformational state transition. For each polymer, two global energy maps of a meso and a racemic dyad were finally constructed from the superposition of energy data for the three kinds of side-group orientations by the Boltzmann factors. From an ensemble average, the proposed scheme with three rotational isomeric states (RIS) allowed us to access the experimentally unperturbed dimensions of PAA chain via the configurational statistical mechanics. Although the calculation was based on the short-range, local interactions, it was interested to note that the experimental characteristic ratios just fell within the range calculated for atactic chains.

Microstructure and Mechanical Properties of Poly (Vinyl Chloride) Modified by Silica Fume /Acrylic Core-Shell Impact Modifier Blends

This research explored replacing acrylic core-shell impact modifier （AIM） by silica fume to toughen PVC. 100%, 75%, 50% and 25% of AIM （8 phr） were substituted by silica fume in PVC respectively, and then processed by dry blending and twin-screw extrusion. Severe silica fume agglomeration was observed by scanning electron microscope （SEM） in the PVC matrix when 8 phr pure silica fume was used and processed by screw speed of 20 rpm. Its tensile strength was thereby reduced by 38% comparing to unmodified PVC. The silica fume was successfully dispersed while the screw speed was slowed down to 10 rpm to give a stronger screw torque and a longer melt residential time in the extruder. The tensile strength was ’recovered’ to a level comparable to unmodified PVC. Impact test were performed on all formulations extruded at 10 rpm screw speed and synergetic toughening effect was found with 50% substitution and it had the impact strength that was comparable to 8 phr pure AIM toughened PVC.

Poly (Acrylamide-co-Acrylic Acid) Hydrogel Induced by Glow-Discharge Electrolysis Plasma and Its Adsorption Properties for Cationic Dyes

In this paper, poly （acrylamide-co-acrylic acid） （P（AM-co-AA）） hydrogel was pre- pared in an aqueous solution by using glow-discharge electrolysis plasma （GDEP） induced copoly- merization of acrylamide （AM） and acrylic acid （AA）, in which N,N＇-methylenebisacrylamide （MBA） was used as a crosslinker. A mechanism for the synthesis of P（AM-co-AA） hydrogel was proposed. To optimize the synthesis condition, the following parameters were examined in detail： the discharge voltage, discharge time, the content of the crosslinker, and the mass ratio of AM to AA. The results showed that the optimum pH range for cationic dyes removal was found to be 5.0-10.0. The P（AM-co-AA） hydrogel exhibits a very high adsorption potential and the ex- perimental adsorption capacities for Crystal violet （CV） and Methylene blue （MB） were 2974.3 mg/g and 2303.6 mg/g, respectively. The adsorption process follows a pseudo-second-order kinetic model. In addition, the adsorption mechanism of P（AM-co-AA） hydrogel for cationic dyes was also discussed.

Molecular Imprinting Fibrous Membranes of Poly(acrylonitrile-co-acrylic acid) Prepared by Electrospinning

IntroductionOver the past few decades, molecular imprinting has been described as a technology for preparing ＂molecular doors＂ which can be matched to ＂template keys＂. It has been found to be a simple and effective approach to introduce specific recognition sites into synthetic polymers, namely, to create molecular imprinting polymers Remarkable features such as stability, ease of preparation and low cost, have made molecular imprinting polymers particularly attractive in chemical sensors, catalysis, drug delivery, and dedicated separations. Practical applications of molecular imprinting polymers require accessible sites, fast mass transfer, and quick binding. However, present techniques used to prepare molecular imprinting polymers most often result in materials exhibiting a high affinity and selectivity but a low capacity and poor site accessibility for the target molecules. It is also very difficult to remove the imprinted molecules located in these molecular imprinting polymers because the highly cross-linked structures do not allow the templates to move freely. To some extent, combining molecular imprinting technology with membrane separation and surface imprinting can overcome the shortcomings, such as mass transfer limitations and non-quantitative recovery of the template molecules seen for imprinted materials fabricated by conventional bulk methods. In that ease, it appears to us that molecular imprinting polymers with high surface area to volume ratios are particularly desirable for largescale applications. Eleetrospun nano and ultrafine fibrous membranes are the most suitable materials due to advantages such as： （1） large specific surfaces, providing relatively high imprinting sites per unit mass; （2） fine porous structures, resulting in the accessibility of imprinting sites and low diffusion resistance necessary for high efficiency; and （3） easy recoverability from practical operation or applicability for continuous usages. Therefore, in this work, we prepared a unique kind of imprinted material--molecularly imprinted fibrous membranes of poly （ acrylonitrile-co-acrylic acid） fabricated by means of an electrospinning process.

CD POLY/Acrylic/Viscose混纺弹性织物气流机染色

用阳离子染料对CD POLY／Acrylic／Viscose混纺弹性织物进行一浴法染色，在大货生产中容易出现色差、折痕和毛头等问题。实验通过分段式升温，控制40-70℃升温速率为1．0℃／min，70-90℃升温速率为0．3℃／min，90-105℃升温速率为0．5℃／min，105℃保温30min能有效控制色差问题；气流机染色选用合适的行机条件也是控制质量问题的关键。设定行机条件为45％的风机，80％N差，机速350m／min，行一圈时间2．75min。大生产证明织物的布面品质良好。

Synthesis and Properties of IPN Hydrogels Based on Konjac Glucomannan and Poly(acrylic acid)

Novel interpenetrating polymer network （IPN） hydrogels based on konjac glucomannan （KGM） and poly（acrylic acid） （PAA） were prepared by polymerization and cross-linking of acrylic acid （AA） in the pre-fabricated KGM gel. The IPN gel was analyzed by FF-IR. The studies on the equilibrium swelling ratio of IPN hydrogels revealed their sensitive response to environmental pH value. The results of in vitro degradation showed that the IPN hydrogels retain the enzymatic degradation character of KGM.

Preparation and Properties of Carrageenan-g-Poly(Acrylic Acid)/Bentonite Superabsorbent Composite

A novel biopolymer-based superabsorbent hydrogel composite based on kappa-carrageenan (κC) have been prepared via graft copolymerization of acrylic acid (AA) in the presence of bentonite powder using methylenebisacrylamide (MBA) as a crosslinking agent and ammonium persulfate (APS) as an initiator. The hydrogel structure was confirmed using FTIR spectroscopy and the morphology of the samples was examined by scanning electron microscopy (SEM). The affecting variables onto graft polymerization (i.e. AA, MBA and APS concentration, as well as the bentonite amount) were systematically optimized to achieve a hydrogel with swelling capacity as high as possible. The results of Brunauer–Emmett–Teller (BET) analysis showed that the average pore diameter of the synthesized hydrogel was 11.5 nm. The effect of various salt media and solutions with different pHs on the swelling of the superabsorbent was also studied.

Swelling Behaviors of Polyaniline-Poly(Acrylic Acid) Hydrogels

Using poly（acrylic acid） （PAA） aqueous solution, NaOH aqueous solution, aniline （An） and ammonium persulfate （APS）, PAn-PAA hydrogels with a semi-interpenetrating structure connected by physical interlocks, chemical ion bonds and hydrogen bonds were prepared. The swelling properties of the hydrogels in solutions of different pH values （adjusted by adding NaOH or HCI） were studied. All the hydrogels prepared have similar swelling curves （the curves of equilibrium swelling ratio vs. pH value） and reach their maximum swelling at pH of 8 - 10. The maximum swelling ratio of the hydrogels is dependent on composition, including molecular weight of PAA, polymer content of the hydrogel, and molar ratios of AA to An, APS to An, and NaOH to AA, And the compositional dependence of the swelling capacity of PAn-PAA hydrogels was also studied.

Synthesis and application of a novel star-hyperbranched poly(acrylic acid) for improved dental restoratives

A new star-hyperbranched poly(acrylic acid) has been synthesized and incorporated into dental glassionomer cement for enhanced mechanical strengths. The effects of arm number and branching on viscosity of the polymer aqueous solution and mechanical strengths of the formed experimental cement were evaluated. It was found that the higher the arm number and the more the branching, the lower the viscosity of the polymer solution as well as the mechanical strengths of the formed cement. It was also found that the experimental cement exhibited significantly higher mechanical strengths than commercial Fuji II LC. The experimental cement was 51% in CS, 55% in compressive modulus, 118% in DTS, 82% in FS, 18% in FT and 85% in KHN higher than Fuji II LC. The experimental cement was only 6.7% of abrasive and 10% of attritional wear depths of Fuji II LC in each wear cycle. It appears that this novel experimental cement is a clinically attractive dental restorative and may potentially be used for high-wear and high-stress-bearing site restorations.

Studies on Micellization of a Polystyrene-b-poly(acrylic acid) Copolymer in Aqueous Media by Pyrene Fluorescence

Pyrene probe and TEM have been employed to investigate the behavior of a polystyrene-b-poly(acrylic acid) (PS-b-PAA) copolymer in aqueous solution. A significant annealing temperature effect on the I1/I3 ratio of pyrene was observed and was interpreted in terms of the morphological change of micellar cores. Annealing at a temperature higher than the glass transition temperature (Tg) of PS leads to densification of the hydrophobic core.

Poly(Acrylamide-Co-Acrylic Acid)-Zinc Acetate Polymer Electrolytes: Studies Based on Structural and Morphology and Electrical Spectroscopy

Solid polymer electrolytes (SPEs) of polyacrylamide-co-acrylic acid (PAA) as the polymer host and zinc acetate (ZnA) as an ionic dopant were prepared using a single solvent by the solution casting technique. The amorphous and crystalline structures of film were investigated by X-ray diffraction (XRD). The surface morphology of samples was examined by scanning electron microscopy (SEM). The composition and complex formation of films were characterized by Fourier transform infrared (FTIR) spectroscopy. The conductivity of the PAA-ZnA films was determined by electrochemical impedance spectroscopy. According to the XRD and FTIR analyses, all electrolyte films were in amorphous state and the existence of interaction between Zn2+ cations and the PAA structure confirms that the film was successfully prepared. The SEM observations reveal that the electrolyte films appeared to be rough and flat with irregularly shaped surfaces. The highest ionic conductivity (σ) of 1.82 × 10-5 Scm-1 was achieved at room temperature (303 K) for the sample containing 10 wt % ZnA.

PREPARATION AND MECHANICAL PROPERTIES OF POLY(METHYL METHACRYLATE)/ URETHANE ACRYLATE COPOLYMERS

The urethane acrylate(UA) was made of poly(tetramethylenc oxide), 4,4’-diphenylmethane diisocyanate, and 2-hydroxyethyl methacrylate. A series of poly(methyl methacrylate) / urethane acrylate copolymers was prepared by using a redox initiating system. The copolymers had cross linked structures and two-phase morphologies as indicated by the results of the dynamic mechanical measurement and swelling test.

COMPUTER SIMULATIONS ON UNPERTURBED CONFIGURATIONAL DIMENSIONS OF POLY (METHYL ACRYLATE)

A full-relaxation optimization of molecule and the popular MM2 force field are employed to obtain the geometry parameters and the conformational energy surface of a meso or a racemic dyad of poly(methyl acrylate) (PMA) with a specified carbonyl-bond orientation in side-groups. It is found that the conformational energy maps calculated here considerably differ from those calculated with the rigid molecular model as reported in the earlier studies. The g(-) state cannot be omitted in the obtained contour maps. Two important conformers tg(-) and g(-t) with energy minima were newly detected for a racemic dyad. The analysis on the conformations with energy minima confirmed that the ester groups are not always perpendicular to the plane defined by the two adjacent skeletal bonds and may change their relative orientations to meet the requirement of lower energies during the conformational state transition. Instead of the early way of adjusting the interaction energy parameters to fit the experimental data, we attempt to predict unperturbed chain dimensions via the reliable force field and the configurational statistical mechanics. The proposed scheme with three rotational states identified from the contour maps allowed us to satisfactorily reproduce the experimental dimensions of random PMA chains.

Rapid Expansion of Supercritical Solution of Poly (1,1,2,2- Tetrahy-droperfluorodecyl Acrylate)

Poly(1,1,2,2- tetrahydroperfluorodecyl acrylate) (poly (TA-N)) was synthesized in laboratory. The resulting morphology of rapid expansion of supercritical solution (RESS) sprays of poly(TA - N) was investigated. At apre - expansion temperature of 45℃), amorphous polymer was formed. At temperature around 60 ℃ to 80 ℃ , fibers were formed. Increase of temperature increasesparticle size slightly. At temperature of 105℃ , most of particles are spheres. The RESS is an attractive process. To apply the polymers desired for coating applications in an organic solvent - free process that is economically viable , and it will have implications for pollution prevention during polymer film

EFFECTS OF ω-ACRYLOYL POLY (ETHYLENE OXIDE) MACROMONOMER ON EMULSIFIER-FREE EMULSI0N COPOLYMERIZATION OF METHYL METHACRYLATE AND n-BUTYL ACRYLATE

Well-defined nonionic hydrophilic ω-acryloyl poly(ethylene oxide) macro-monomer (PEO-A) has been prepared by living anionic polymerization of ethylene oxidewith diphenyl methyl potassium as the initiator and acryloyl chloride as the reaction termi-nating agent. The polymer was characterized by FTIR and SEC. The emulsifier-free emul-sion polymerization of methyl methacrylate (MMA) and n-butyl acrylate (BA) containingvarious concentrations of PEO-A was studied. In all cases stable emulsion coplymerizationsof MMA and BA were obtained. The stabilizing effect was found to be dependent on themolecular weight and the feed amount of the macromonomer.