Enzymatic Degradation of Poly(butylenesuccinate)/Thermoplastic Starch Blend

The degradation of thermoplastic starch blend in the presence of commerciala-amylase and unpurified amylase of microbial origin was investigated.The blends consisting of thermoplastic starch and poly(butylene succinate)have potential use in packaging applications thus,it is essential to establish susceptibility to degradation.Molar mass loss,gravimetric weight loss,and molecular structure were evaluated.The changes in the surface were observed with scanning electron microscopy.It was confirmed that there was a significant difference in gravimetric weight loss between the blends degraded in two different solutions.Unpurified enzymes of microbial origin,produced by Rhizopus oryzae cultures decomposed analyzed materials more efficiently than purified commercial ones.Moreover,it was proved that in applied conditions,the molar mass of PBS fraction did not change significantly.

Improving Polylactide Toughness by Plasticizing with Low Molecular Weight Polylactide-Poly(Butylene Succinate)Copolymer

A low-molecular-weight polylactide-poly(butylene succinate)(PLA-PBS)copolymer was synthesized and incorporated into polylactide(PLA)as a novel toughening agent by solvent casting.The copolymer had the same chemical structure and function as PLA and it was used as a plasticizer to PLA.The copolymer was blended with PLA at a weight ratio from 2 to 10 wt%.Phase separation between PLA and PLA-PBS was not observed from their scanning electron microscopy(SEM)images and the crystal structure of PLA almost remained unchanged based on the X-ray diffraction(XRD)measurement.The melt flow index(MFI)of the blends was higher as the amount of PLA-PBS increased,indicating that the block copolymer did improve the mobility of the PLA chains.Moreover,tensile tests revealed that PLA with greater PLA-PBS copolymer exhibited higher elongation at break and it reached the maximum at 8 wt%of PLA-PBS in PLA,which was around 6 times higher than that of pure PLA.Furthermore,the glass transition temperature,measured by differential scanning calorimetry(DSC),markedly decreased with an increasing amount of the copolymer as it decreased from 61.2℃ for pure PLA to 41.3℃when it was blended with 10 wt%PLA-PBS copolymer.Therefore,the PLA-PBS copolymer was shown to be a promising plasticizer for fully biobased and toughened PLA.

DSC Study of Thermal Properties of Biodegradable Poly(Butylene Succinate-co-terephthalate)

Poly(butylene succinate) (PBS),poly(butylene terephthalate) (PBT) and poly(butylene succinate-co-terephthalate) (PBST)s were synthesized from dimethyl succinate and/or dimethyl terephthalate reacting with 1,4-butanediol through a process of transesterification/polycondensation in the presence of a high effective catalyst and characterized by means of GPC and DSC. The investigation was mainly focused on the influence of content of terephthalate units on the molecular weight and thermal properties of resulting polymers. It is revealed that the melting temperature and crystallinity of synthesized polymers decrease first with the increase of terephthalate units, then shift to rise gradually by DSC measurements. The results of Flory equation suggest sequence structure of PBSTs is random.

Construction and evaluation of co-electrospun poly (butylene succinate)/gelatin materials as potential vascular grafts

In this study,a series of poly(butylene succinate)(PBSU)/gelatin composites were prepared by electrospinning.The morphology,physicochemical analysis,biomechanical properties,biocompatibility,and biodegradability of the materials were evaluated.The results showed that the ultimate tensile stress of the vascular PBSU/gelatin grafts at(95/5),(90/10),(85/15),and(80/20)was(4.17±0.54)MPa,(3.81±0.44)MPa,2.94±0.69 MPa and 2.11±0.72 MPa respectively,and the burst pressure was(282.7±22.3)kPa,(295.3±3.9)kPa,(306.8±13.9)kPa and(307.6±9.0)kPa respectively,which met the requirements of tissue-engineered blood vessels.Furthermore,the addition of gelatin improved the hydrophilicity and degradation properties of PBSU,thus enhancing cell adhesion and promoting the inward growth of vascular smooth muscle cells.In summary,the research in this paper provides a useful reference for the preparation and optimization of vascular scaffolds.

Crystallization and Dynamic Mechanical Behavior of Coir Fiber Reinforced Poly(Butylene Succinate)Biocomposites

The crystallization behavior,crystal morphology and form,and viscoelastic behavior of poly(butylene succinate)(PBS)and coir fiber/PBS composites(CPB)were investigated by differential scanning calorimetry(DSC),polarized optical microscopy(POM),X-ray diffraction(XRD)and dynamic mechanical analysis(DMA).The results of DSC measurement show that the crystallization temperature increases with the filling of coir fibers.POM images reveal that the spherulitic size and crystallization behavior of PBS are influenced by the coir fibers in the composites.XRD curves show that the crystal form of pure PBS and CPB are remaining almost identical.In addition,the storage modulus of CPB significantly increases comparing with the pure PBS.This predicted the dimensional stability and improved load-deformation temperature.In conclusion,the addition of coir fibers has a significant effect on the thermal properties of the matrix.

Influencing Factors and Process on <i>in Situ</i>Degradation of Poly(<i>Butylene Succinate</i>) Film by Strain <i>Bionectria ochroleuca</i>BFM-X1 in Soil

This is the first report on the PBS film degraded by any Bionectria ochroleuca fungal strain. The fungal strain BFM-X1 was isolated from an air environment on a vegetable field and was capable of degrading poly(butylene succinate) (PBS). The taxonomic identity of the strain BFM-X1 was confirmed to be Bionectria ochroleuca (showing a 99% similarity to B. ochroleuca in a BLAST search) through an ITS rRNA analysis. The bio-degradation of the PBS film by strain BFM-X1 was studied. Approximately 97.9% of the PBS film was degraded after strain BFM-X1 was inoculated at 28?C for 14 days. The degradation efficiency of BFM-X1 against PBS film under different soil environmental conditions was characterized. The results indicated that 62.78% of the PBS film loss was recorded in a 30-d experimental run in a sterile soil environment indoors. On adding strain BFM-X1 to a soil sample, the PBS degradation rate accelerated approximately fivefold. Furthermore, both temperature and humidity influenced the in situ degradation of the PBS by strain BFM-X1, and temperature may be the major regulating factor. The degradation was particularly effective in the warm season, with 90% of weight loss occurring in July and August. Scanning electron microscope observations showed surface changes to the film during the degradation process, which suggested that strain BFM-X1preferentially degraded an amorphous part of the film from the surface. These results suggested that the strain B. ochroleuca BFM-X1 was a new resource for degrading PBS film and has high potential in the bioremediation of PBS-plastic-contaminated soil

THERMAL PROPERTY, MISCIBILITY AND CRYSTALLIZATION BEHAVIOR OF POLY(3-HYDROXYBUTYRATE-co-3-YDROXYHEXANOATE) AND POLY(BUTYLENE SUCCINATE-ADIPATE) (PHBHHX/PBSA) BLENDS

Blends of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) and poly(butylene succinate-adipate) (PBSA), both biodegradable semicrystalline polyesters, were prepared with the ratio of PHBHHx/PBSA ranging from 80/20 to 20/80 by melt mixing method. Differential scanning calorimetry (DSC), thermogravimetry analysis (TGA), dynamic mechanical thermal analysis (DMA), polarizing optical microscopy (POM) and wide angle X-ray diffractometer (WAXD) were used to study the miscibility and crystallization behavior of PHBHHx/PBSA blends. Experimental results indicate that PHBHHx is immiscible with PBSA as shown by the almost unchanged glass transition temperature and the biphasic melt.

Nonisothermal Crystallization Kinetics of Poly(butylene adipate-co-terephthalate) Copolyester

Nonisothermal crystallization behavior of poly(butylene adipate-co-terephthalate)(PBAT) synthesized via direct esterification and polycondensation reactions was investigated by the differential scanning calorimetry(DSC).The Avrami equation modified by Jeziorny and the Z.S.Mo equation were employed to describe the non-isothermal crystallization kinetics of copolyester samples.The test results showed that the Avrami equation was successful in describing nonisothermal crystallization process of PBAT copolyesters.PBAT copolyester could give birth to secondary crystallization.The crystallization parameter(Zc) increased with an increasing cooling rate and the Avrami exponent(n) was around 2.3.For a given cooling rate,the value of Zc demonstrated a sagging trend with an increase in adipic acid(AA) content.The equation proposed by Z.S.Mo was successful in describing the nonisothermal crystallization kinetics of PBAT copolyesters.

Preparation and Properties of a New Type of Poly(butylene-terephthalate)with Layered Silicate Nanocomposites

In this paper, poly(butylene-terephthalate)-layered silicate of clay nanocomposites (NPBT) are reported. Their thermal properties, heat distortion temperature (HDT) and crystallization nucleation are investigated. NPBT samples have apparent viscosity over 0.85, HDT of 30℃ to 50℃ higher than that of poly (butyleneterephthalate) (PBT) for clay load from 1.0% to 10.0% (by mass), and higher capability to accommodate clay than other polymers. The nonisothermal crystallization experiments indicate that the better thermal degradation behavior and crystallization rate of NPBT are 50% higher than PBT, and its injection mould processing temperature is lowered from ll0℃ to 55℃. NPBT samples are characterized by several techniques. X-ray shows an original clay interlayer distance enlarged from 1.0 nm to 2.5 nm, while both TEM and AFM indicate an average size from 30nm to 100nm of exfoliated clay layers, and 3%(by mass) of particle agglomeration being phase separated from PBT matrix, which are factors on some mechanical properties decrease of NPBT. The disappearance of spherulitic morphology in NPBT resulted from layers nucleation is detected. Improving NPBT properties by treating clay with long chain organic reagent and controlling the way to load it is suggested.

Thermal Behavior and Crystal Transition of Biodegradable Poly(butylenes adipate)Revealed by Two-Dimensional Correlation Spectroscopy

In the present study,thermal behavior and crystal transition of pure poly(butylene adipate)(PBA)upon heating process were investigated by FTIR spectroscopy.To gain further insight into the thermal behavior alteration and the phase transition of PBA,we performed two-dimensional(2D)correlation analysis.We found thatβ-form PBA crystal undergoes not only the melting process but also crystal transition upon the heating process.

TRANSESTERIFICATION OF POLY(BISPHENOL A CARBONATE) WITH AROMATIC AND ALIPHATIC SEGMENTS IN BUTYLENE TEREPHTHALATE-CAPROLACTONE COPOLYESTER

In this article, the transesterification of poly(bisphenol A carbonate) (PC) with butylene terephthalate-caprolactone copolyester at a weight ratio 50/50 (BCL(21)) was thoroughly investigated by proton nuclear magnetic resonance spectroscopy ('H-NMR), in conjunction with a model compound. The 1 H-NMR results of the annealed blend PC/BCL(21) show that the formation of bisphenol A-terephthalate ester units is the same as in the annealed blend of PC with PBT, and the transesterification actually occurs between PC and butylene terephthalate (BT) segments in BCL(21). By comparison with the model compound bisphenol A dibutyrate, the new signal appearing at δ= 2.56 in the 1H-NMR spectrum confirms the existence of bisphenol A caprolactone ester units resulting from the exchange reaction of PC with caprolactone (CL) segments. 1H-NMR analysis of the transesterification rates reveals that the reaction of PC with aromatic and aliphatic segments in BCL(21) proceeds in a random manner. The miscibility of the blend PC/BCL(21) copolyester is favorable for the transesterification of PC with BT segments and CL segments.

Delivery of docetaxel using pH-sensitive liposomes based on D-α-tocopheryl poly(2-ethyl-2-oxazoline) succinate:Comparison with PEGylated liposomes

This study aimed to investigate the ability of the novel materials D-α-tocopheryl poly(2-ethyl-2-oxazoline) succinate(TPOS) to construct pH-sensitive liposomes. TPOS was initially synthesized and characterized by TLC, FTIR, and ~1H-NMR. The buffering capacity of polyethylene glycol-distearoyl phosphatidylethanolamine(PEG-DSPE) and TPOS was determined by acid-base titration, and TPOS displayed a slower downtrend and gentler slope of titration curve than PEG-DSPE within pH 7.4–5.0. Studies on the in vitro drug release demonstrated that TPOS modified docetaxel(DOC) liposomes(TPOS-DOC-L) had a slower drugrelease rate at pH 7.4 similar to PEGylated-DOC liposomes(PEG-DOC-L), whereas the release rate reached approximately 86.92% ± 1.69% at pH 6.4. In vitro cellular uptake assays by microplate reader, and flow cytometry revealed that TPOS modified coumarin 6 liposomes(TPOS-C6-L) had stronger cellular uptake at pH 6.4 than that at pH 7.4( P < 0.01). Conversely, for PEGylated C6 liposomes(PEG-C6-L) and conventional C6 liposomes(C6-L), very similar cellular uptakes were exhibited at different pH values. Confocal laser scanning microscopy images showed that PEG-C6-L and C6-L were mainly located in lysosomes. By contrast, TPOS-C6-L showed broader cytoplasmic release and distribution at 4 h. MTT assay showed that the cytotoxicity of TPOS-DOC-L was similar to that of PEG-DOC-L and conventional DOC liposomes(DOC-L) at the same DOC concentration and at pH 7.4, but was much lower than those at pH 6.4 after 48 h of incubation. The apoptosis of PEG-DOC-L and DOC-L had no remarkable improvement with decreased pH from 7.4 to 6.4. Meanwhile, TPOS-DOC-Lsignificantly induced the apoptosis of HeLa cells with decreased pH. Therefore, TPOS can be a biomaterial for the construction of a pH-sensitive drug delivery system.

Nanocellulose: Effect on Thermal, Structural, Molecular Mobility and Rheological Characteristics of Poly(Butylenes Adipate-Co-Butylene Terephthalate) Nanocomposites

The concern with environmental preservation is a very current and relevant topic. Regarding polymers, the search for potentially ecofriendly matters has been the subject of scientific research. In this context, this work aimed to study the effect of adding nanocellulose (nCE) with 1, 3, and 5 wt.% on poly(butylene adipate-co-butylene terephthalate) (PBAT). Thermal, structural, relaxometric, and rheological assessments were carried out. Quantitative evaluation of PBAT copolymer by high field NMR revealed 56.4 and 43.6 m.% of the butylene adipate and butylene terephthalate segments, respectively. WAXD measurement on the deconvoluted diffraction patterns identified that nCE was a mixing of Cellulose I and Cellulose II polymorph structures. At any composition, nanocellulose interfered with the PBAT crystallisation process. Also, a series of new PBAT crystallographic planes appeared as a function of nanocellulose content. PBAT hydrogen molecular relaxation varied randomly with nanocellulose content and had a strong effect on the hydrogen relaxation. PBAT cold crystallisation and melting temperatures (Tcc and Tm) were almost unchangeable. Although Tcc did not change during polymer solidification from PBAT molten state, the sample’s degree of crystallinity varied with composition through the transcrystallization phenomenon. Nanocomposite thermal stability decreased possibly owing to the catalytic action of sulfonated amorphous cellulose chains. For the sample with 3 wt.% of nanocellulose, the highest values of complex viscosity and storage modulus were achieved.

Generation of Tough Poly(glycolic acid)(PGA)/Poly(butylene succinate-co-butylene adipate)(PBSA)Films with High Gas Barrier Performance through In situ Nanofibrillation of PBSA under an Elongational Flow Field

Poly(glycolic acid)(PGA)is derived from glycolide obtained by fermenting pineapples or sugarcane,which has excellent gas barrier properties and a small carbon footprint.PGA is a potential substitute for the current aluminum-plastic composite films used in high barrier packaging applications.However,its poor ductility and narrow processing window limit its application in food packaging.Herein,poly(butylene succinate-co-butylene adipate)(PBSA)was used to fabricate PGA/PBSA blend films through an in situ fibrillation technique and blown film extrusion.Under the elongational flow field used during the extrusion process,a unique hierarchical structure based on the PBSA nanofibrils and interfacially oriented PGA crystals was obtained.This structure enhances the strength,ductility and gas barrier properties of the PGA/PBSA blend film.In addition,an epoxy chain extender(ADR4468)was used as a compatibilizer to further enhance the interfacial adhesion between PGA and PBSA.70PGA/0.7ADR exhibited a very low oxygen permeability(2.34×10^(-4)Barrer)with significantly high elongating at break(604.4%),tensile strength(47.4 MPa),and transparency,which were superior to those of petroleum-based polymers.Thus,the 70PGA/0.7ADR blown films could satisfy the requirements for most instant foods such as coffee,peanuts,and fresh meat.

Enhanced Crystallization of Poly(butylene adipate-co-terephthalate)by a Self-assembly Nucleating Agent

Poly(butylene adipate-co-terephthalate)(PBAT)is a promising biodegradable flexible polymer but suffers from slow crystallization rate,making it less attractive for some applications like the injection-molded products in comparison with low-density polyethylene(LDPE).This work aimed to accelerate the crystallization of PBAT by adding a self-assembly nucleating agent octamethylenedicarboxylic dibenzoylhydrazide(OMBH).PBAT/OMBH composites with various OMBH contents(0 wt%,0.5 wt%,0.7 wt%,1 wt%,2 wt%,3 wt%and 5 wt%)were prepared through melt-mixing.The effect of OMBH on the crystallization behavior,morphologies and mechanical properties of PBAT was investigated.The highest nucleation efficiency value of 59.6%was achieved for PBAT with 0.7 wt%OMBH,much higher than that of 22.7%for PBAT with 0.7 wt%talc.Atomic force microscopy results showed that OMBH formed fine fibers and induced the formation of transcrystalline layers of PBAT.Fourier transform infrared spectroscopy(FTIR)combined with two-dimensional correlation spectra suggested that the intermolecular dipole-dipole N—H…O=C interactions but not hydrogen bond between OMBH and PBAT promoted the crystallization of PBAT in the initial period of crystallization.The presence of OMBH did not change the crystal form of PBAT but had positive contribution in enhancing its crystallinity and mechanical properties.This work is essential for preparing PBAT with high crystallization rate,enhancing its potential applications in injection-molded products.

淀粉的改性及其对淀粉/PBAT/碳酸钙复合材料结构和性能的影响

采用甘油、六偏磷酸钠(SHMP)和聚乙二醇(PEG)改性木薯淀粉并制备改性淀粉/聚己二酸对苯二甲酸丁二醇酯(PBAT)/碳酸钙复合材料,采用傅里叶变换红外光谱仪(FTIR)、X射线衍射仪(XRD)、扫描电子显微镜(SEM)、差示扫描量热仪(DSC)、热失重分析仪(TG)等对改性淀粉和复合材料进行分析,研究改性淀粉对复合材料结构和性能的影响。结果表明,甘油的外增塑作用和PEG、SHMP的内增塑作用使淀粉化学结构改变、无定形成分增加,淀粉颗粒由饱满的圆球状变成了不规则的大颗粒,250℃前稳定性提高,250℃后稳定性降低,有利于使用加工和热分解,不同改性剂改性淀粉结晶熔融行为存在差异;复合不会改变PBAT、碳酸钙和淀粉的原有晶型,但相容性的差异导致复合材料热性能和力学性能的差异,改性淀粉增加了复合材料的韧性,甘油、SHMP和PEG的协同改性使淀粉与PBAT、碳酸钙的相容性最佳,复合材料的综合性能最好。

Effects of Crystallization Temperature and Blend Ratio on the Crystal Structure of Poly(butylene adipate) in the Poly(butylene adipate)/Poly(butylene succinate) Blends

The effects of crystallization temperature and blend ratio on the polymorphic crystal structures of poly（butylene adipate） （PBA） in poly（butylene succinate） （PBS）/poly（butylene adipate） （PBS/PBA） blends were studied by means of differential scanning calorimetry （DSC）, wide-angle X-ray diffraction （XRD） and atomic force microscopy （AFM）. It was revealed that the polymorphism of PBA can be regulated by the blend ratio even in a non-isothermal crystallization process. The results demonstrate that high temperature favors fiat-on α crystals, while low temperature contributes to edge-on β crystals. It was also found that the effect of blend ratio on the crystallization mechanism of PBA is well coincident with that of the crystallization temperature. The increment of PBS content in the PBS/PBA blend gives rise to more β-form crystals of PBA. For those PBS/PBA blends with low PBA content, the interlamellar phase segregation of PBA makes its molecular chains so difficult to diffuse from one isolated microdomain to another that high crystallization temperature and sufficiently long crystallization time will be required if the PBA α-type crystals are targeted.

EFFECT OF POLY(BUTYLENE SUCCINATE) ON THE MORPHOLOGY EVOLUTION OF POLY(VINYLIDENE FLUORIDE) IN THEIR BLENDS

The effect of PBS on the morphological features of PVDF has been investigated by optical and atomic force microscopies under various conditions. It was found that neat PVDF forms large γform spherulites with extraordinarily weak birefringence at 170℃. Adding 30% PBS makes PVDF exhibit intrigued flower-like spherulitic morphology. The growth mechanism was explained by the decrease of the supercooling and the materials dissipation. Increasing the PBS content to 70% favors the formation of ring banded spherulites. Temperature dependent experiments verify the α→γ phase transition occurs from the junction sites of the ot and y crystals, while starts from the centers of α spherulites in the blends. Ring banded structures could be observed in neat PVDF, 70/30 blend and 30/70 blend when crystallized at 155℃, without γ crystals. The band period of PVDF α spherulites increases with crystallization temperature as well as the amount of PBS content. At 140℃, spherulites in neat PVDF lose their ring banded feature, while coarse spherulites consisting of evident lamellar bundles could be found in 30/70 blend.

Effect of Molecular Weight on the Properties of Poly(butylene succinate)

Poly（butylene succinate） （PBS） with different molecular weight was synthesized from 1, 4-butanediol and succinic acid by direct melt condensation. The synthesized PBS was identified by IH-NMR and FTIR spectrometry. The molecular weight was calculated from the intrinsic viscosity, and its value was between 20000 and 70000. The crystallization behavior and crystal morphology as function of molecular weight were investigated by DSC and PLM, respectively. The mechanical properties and hydrolytic degradation behaviors related with change of molecular weight were also studied in this work. The results demonstrated that the properties of PBS were determined by both molecular weight and crystallization properties （crystallinity as well as crystal morphology）. Our work is important for the design and preparation of PBS with proper molecular weight for its practical application.

NONISOTHERMAL CRYSTALLIZATION AND MORPHOLOGY OF POLY(BUTYLENE SUCCINATE)/LAYERED DOUBLE HYDROXIDE NANOCOMPOSITES

Biodegradable poly（butylene succinate） （PBS） and layered double hydroxide （LDH） nanocomposites were prepared via melt blending in a twin-screw extruder. The morphology and dispersion of LDH nanoparticles within PBS matrix were characterized by transmission electron microscopy （TEM）, which showed that LDH nanoparticles were found to be well distributed at the nanometer level. The nonisothermal crystallization behavior of nanocomposites was extensively studied using differential scanning calorimetry （DSC） technique at various cooling rates. The crystallization rate of PBS was accelerated by the addition of LDH due to its heterogeneous nucleation effect; however, the crystallization mechanism and crystal structure of PBS remained almost unchanged. In kinetics analysis of nonisothermal crystallization, the Ozawa approach failed to describe the crystallization behavior of PBS/LDH nanocomposites, whereas both the modified Avrami model and the Mo method well represented the crystallization behavior of nanocomposites. The effective activation energy was estimated as a function of the relative degree of crystallinity using the isoeonversional analysis. The subsequent melting behavior of PBS and PBS/LDH nanocomposites was observed to be dependent on the cooling rate. The POM showed that the small and less perfect crystals were formed in nanocomposites.